e m p a p e l r e c i c l a d o p ó s u t i l i z a ç ã o .
n p a p e l r e c i c l a d o .
LC-20M4U
LCD AV MONITOR
MONITEUR AV À CRISTAUX
LIQUIDES
OPERATION MANUAL
MODE D’EMPLOI
Printed in Japan
Imprimé au Japon
Printed on post-consumer recycled paper.
Imprimé sur du papier recyclé.
2
TINS-7530CEZZ
01P11-JKK
LC-20M4U
LCD AV MONITOR
ENGLISH
OPERATION MANUAL
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
The lightning flash with arrow-
head symbol, within an equilat-
eral triangle, is intended to alert
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a
triangle is intended to alert the
user to the presence of impor-
tant operating and maintenance
(servicing) instructions in the
literature accompanying the
product.
IMPORTANT INFORMATION
Declaration of Conformity
SHARP LCD AV MONITOR MODEL LC-20M4U
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430
TEL : 1-800-BE-SHARP (1-800-237-4277)
U.S.A. ONLY
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY
CAUTION: Use the supplied AC cord as it is.
Do not remove the core part from the AC cord, and do not
change the way of winding cables around the core part.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Relocate or adjust the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
2
IMPORTANT INFORMATION (Continued)
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronic Industries Alliance:
3
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp LCD product. To ensure safety and many
years of trouble-free operation of your product, please read the Safety Precautions
carefully before using this product.
IMPORTANT SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property
damage if improperly handled. This product has been engineered and manufactured with the highest
priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent
potential danger, please observe the following instructions when installing, operating and cleaning the
product. To ensure your safety and prolong the service life of your LCD product, please read the following
precautions carefully before using the product.
1. Read instructions—All operating instructions must be read and understood before the product is
operated.
2. Keep this manual in a safe place—These safety and operating instructions must be kept in a safe
place for future reference.
3. Observe warnings—All warnings on the product and in the instructions must be observed closely.
4. Follow instructions—All operating instructions must be followed.
5. Cleaning—Unplug the power cord from the AC outlet before cleaning the product. Use a damp
cloth to clean the product. Do not use liquid cleaners or aerosol cleaners.
6. Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate
attachments can result in accidents.
7. Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen
sink and laundry tub, swimming pool and in a wet basement.
8. Stand—Do not place the product on an unstable cart, stand, tripod or table. Placing the product
on an unstable base can cause the product to fall, resulting in serious personal injuries as well as
damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the
manufacturer or sold with the product.
9. When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops,
excessive force and uneven floor surface can cause the product to fall from the
cart.
10. Ventilation—The vents and other openings in the cabinet are designed for
ventilation. Do not cover or block these vents and openings since insufficient
ventilation can cause overheating and/or shorten the life of the product. Do not
place the product on a bed, sofa, rug or other similar surface, since they can
block ventilation openings. This product is not designed for built-in installation; do
not place the product in an enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer’s instructions are followed.
11. Power source—This product must operate on a power source specified on the
specification label. If you are not sure of the type of power supply used in your home, consult your
dealer or local power company. For units designed to operate on batteries or another power
source, refer to the operating instructions.
12. Power cord protection—The power cords must be routed properly to prevent people from stepping
on them or objects from resting on them. Check the cords at the plugs and product.
13. If the AC adapter is misplaced or needs to be replaced, obtain the same type of adapter from a
SHARP service center or your dealer.
14. If you plan to use a 13-VDC power supply unit other than the AC adapter supplied with the
product, make sure the power supply unit provides stable voltage with minimum fluctuations.
Unstable power supply can cause problems in the product.
15. The LCD panel used in this product is made of glass. Therefore, it can break when the product is
dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the
LCD panel breaks.
16. Overloading—Do not overload AC outlets or extension cords. Overloading can cause fire or
electric shock.
17. Entering of objects and liquids—Never insert an object into the product through vents or openings.
High voltage flows in the product, and inserting an object can cause electric shock and/or short
internal parts. For the same reason, do not spill water or liquid on the product.
4
18. Servicing—Do not attempt to service the product yourself. Removing covers can expose you to
high voltage and other dangerous conditions. Request a qualified service person to perform
servicing.
19. Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and
request a qualified service person to perform repairs.
a.When the power cord or plug is damaged.
b.When a liquid was spilled on the product or when objects have fallen into the product.
c.When the product has been exposed to rain or water.
d.When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper
adjustment of controls not described in the instructions can cause damage, which often requires
extensive adjustment work by a qualified technician.
e.When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product
indicates that the product needs servicing.
20. Replacement parts—In case the product needs replacement parts, make sure that the service
person uses replacement parts specified by the manufacturer, or those with the same characteris-
tics and performance as the original parts. Use of unauthorized parts can result in fire, electric
shock and/or other danger.
21. Safety checks—Upon completion of service or repair work, request the service technician to
perform safety checks to ensure that the product is in proper operating condition.
22. Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and
other heat-generating products (including amplifiers).
23. Polarization—This AC adapter may be equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
The LCD panel is a very high technology product with 921,600 thin film transistors, giving you fine
picture details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or
red.
Please note that this does not affect the performance of your product.
5
CONTENTS
Page
DEAR SHARP CUSTOMER ............................................................................................................. 4
IMPORTANT SAFETY PRECAUTIONS .......................................................................................... 4
SUPPLIED ACCESSORIES ............................................................................................................. 7
PREPARATION................................................................................................................................. 8
Power Connection ...................................................................................................................... 8
Batteries for Remote Control .................................................................................................... 8
PART NAMES (Main Unit) ............................................................................................................... 9
Opening and Closing Front Cover............................................................................................ 9
Removing Back Cover.............................................................................................................. 10
PART NAMES (Remote Control) .................................................................................................. 11
BASIC OPERATION ....................................................................................................................... 12
Turning on MAIN POWER ........................................................................................................ 12
Switching the AV INPUT [AV1/AV2] Mode ............................................................................. 12
Sound Volume ........................................................................................................................... 13
ON/OFF Standby ....................................................................................................................... 13
SELECTING THE MENU ITEMS .................................................................................................... 14
ADJUSTMENT ................................................................................................................................ 15
Adjusting the LANGUAGE Settings........................................................................................ 15
Adjusting the PICTURE Settings ............................................................................................ 16
Adjusting the SET UP Settings ............................................................................................... 18
Adjusting the SLEEP TIMER Settings .................................................................................... 19
CONNECTING TO EXTERNAL DEVICES..................................................................................... 20
Connecting to a VCR, a DVD player etc. (AV 1/2 IN) ............................................................ 20
Connecting to a DVD player (COMPONENT terminal) ......................................................... 21
Outputting video and audio (video output) ........................................................................... 22
Listening with Headphones ..................................................................................................... 22
Fixing the Cables ...................................................................................................................... 22
Watching TV .............................................................................................................................. 23
TROUBLESHOOTING .................................................................................................................... 24
SPECIFICATIONS........................................................................................................................... 25
DIMENSIONAL DRAWINGS .......................................................................................................... 26
6
SUPPLIED ACCESSORIES
Make sure the following accessories are provided with the product.
Operation Manual (×1)
Wireless Remote Control (×1)
LC-20M4U
LCD AV MONITOR
MONITEUR AV Á CRISTAUX
LIQUIDES
OPERATION MANUAL
MODE D’EMPLOI
Printed in Japan
Printed on post-consumer recycled paper.
Imprimé au Japon
Imprimé sur du papier recyclé.
TINS-7530CEZZ
01P11-JKK
RRMCG1459CESA
TINS-7530CEZZ
AC Adapter (×1)
AC Cord (×1)
QACCD3088CEZZ
* Product shape varies in some countries
UADP-0220CEZZ
Cable Clamp (×2)
“AAA” size (UM/SUM-4) Dry Battery (×2)
UBATU0026GEZZ
LHLDW1028GEZZ
7
PREPARATION
Power Connection
Connect to DC input
terminal of the product.
Plug into AC outlet.
AC electrical outlet
AC adapter
AC cord
DC input terminal
(DC 13 V)
Notes:
I Use a commercially available AC plug adapter, if necessary, depending on the design of the wall.
I Always turn the main power switch of the LCD monitor to OFF when connecting the AC adapter.
I Always unplug the AC adapter from the product and power outlet when not being used for a long period of time.
Batteries for Remote Control
If the remote control fails to operate monitor functions, replace the batteries in the remote control.
2 Insert batteries (two “AAA”
size (UM/SUM-4) batteries,
supplied with product).
3 Close the battery
1 Open the battery
cover.
cover.
I Slide the cover while
pressing down.
I Place batteries with their
terminals corresponding to
the (+) and (–) indications
in the battery compartment.
Caution!
Cautions regarding batteries
Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to follow the
instructions below.
• Place batteries with their terminals corresponding to the (+) and (–) indications.
• Different types of batteries have different characteristics. Do not mix batteries of different types.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries
and/or cause old batteries to leak chemicals.
• Remove batteries when they become weak.
Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe with a cloth.
• The batteries supplied with the product may have a shorter life expectancy due to storage conditions.
• If the remote control is not used for an extended period of time, remove batteries from the remote
control.
8
PART NAMES (Main Unit)
Main unit (front view)
To change the vertical angle of
the LCD monitor, tilt the screen
up to 10 degrees backward.
The monitor can also be
rotated 20 degrees horizontally.
Please adjust the angle so that
the monitor can be watched
most comfortably.
Speaker
MENU
Speaker
–
VOL
+
SELECT
AV INPUT
MAIN
POWER
POWER SLEEP
HEAD
PHONE
HEADPHONE
SLEEP indicator
AV INPUT
button
VOL (+)/(–)
buttons
MENU
button
MAIN POWER
switch
SELECT (])/([)
buttons
Remote sensor window
POWER indicator
A green indicator lights when the power
is on and a red indicator lights when in
the standby mode (the indicator will not
light when the main power is off).
Note:
I MENU, VOL (+)/(–), SELECT(])/([), and AV INPUT on the main unit have the same functions as the same
buttons on the remote control. Fundamentally, this operation manual provides a description based on operation
using the remote control.
Opening and Closing Front Cover
I To open the cover, push
.
I To close the cover, press the upper part of the cover.
MAIN
POWER
9
PART NAMES (Main Unit) (Continued)
Main unit (rear view)
Rear Speaker
(woofer)
Stand
Rear terminal section
Can also be used as video
output terminals.
AV 2 IN/OUT
AUDIO
AV 1 IN
S-VIDEO
POWER
INPUT
DC13V
VIDEO
AUDIO
VIDEO
COMPONENT
( )
CB
( )
R CR
R
L
R
L
Y
P
B
P
AUDIO
AUDIO
S-VIDEO
AV 1 IN
POWER INPUT
DC13V
VIDEO
VIDEO
COMPONENT
AV 2 IN/OUT
Removing Back Cover
I When connecting the cords to the terminals, remove the back
cover by gently pulling the part marked forward.
I To replace the back cover, first fit the four top clips (1) into the
corresponding slots of the terminal section, and then align the four
side clips (2) with the corresponding slots. Then, press the marked
parts (3) until the two hooks on the bottom of the cover lock in
place with a click.
Caution!
Before using the LCD AV monitor, be sure to remove the protection tape
and sheet from the back cover.
protection tape and sheet
10
PART NAMES (Remote Control)
Remote control
Infrared transmitter window
Menu control section
Sound MUTE button
MENU button
ON/OFF
MUTE
Power ON/OFF
button
MENU
AV INPUT
AV INPUT
button
SELECT
SELECT (])/([) buttons
VOL
VOL
VOL (+)/(–) buttons
SELECT
LCD MONITOR
Note:
I MENU, VOL (+)/(–), SELECT(])/([), and AV INPUT on the main unit have the same functions as the same
buttons on the remote control. Fundamentally, this operation manual provides a description based on operation
using the remote control.
11
BASIC OPERATION
Turning on MAIN POWER
Control section of main unit
M On-screen display
1 Press MAIN POWER, located on the
front side of the main unit.
AV1
2 The POWER indicator
N358
instantaneously changes from red to
green and the main unit is turned on.
Notes:
I When the POWER indicator is red, press
ON/OFF on the remote control to turn on
the monitor.
The POWER indicator changes from red to
green.
I The input mode indication disappears after
five seconds.
POWER indicator
MAIN POWER
Switching the AV INPUT [AV1/AV2] Mode
1 Turn on the power of the connected
video equipment.
Initial mode (AV1)
2 Press AV INPUT and select the
applicable input source. The screen
displays AV1 or AV2 mode at the
upper right corner each time AV
INPUT is pressed.
ON/OFF
MUTE
MENU
ON/OFF
AV INPUT
AV INPUT
SELECT
SELECT
VOL
VOL
AV1 mode
Note:
I The AV input mode indication remains for
five seconds.
AV1
AV2
• AV1: Select AV1 when video equipment is
connected to the AV 1 IN terminals.
The display of the AV1 mode indicates
either AV1 or COMPONENT depend-
ing on the adjustment of the SET UP
settings.
LCD MONITOR
AV2 mode
AV1 is displayed when AV1 is set to
NORMAL in the SET UP settings, and
COMPONENT is displayed when AV1
is set to COMPONENT.
(see page 18)
• AV2: The AV2 mode can be set to either IN
or OUT in the SET UP settings.
(see page 18)
AV2 indication is not displayed when
the mode is selected to OUT.
12
BASIC OPERATION (Continued)
Sound Volume
To adjust the volume
ON/OFF
MUTE
Press VOL (+) to increase the sound
volume. The indicator segment
increases.
|
MUTE
MENU
AV INPUT
VOLUME
50
SELECT
SELECT
VOL
VOL
Press VOL (–) to decrease the sound
volume. The indicator segment
decreases.
|
VOLUME
10
VOL
(+)/( )
LCD MONITOR
To mute the sound
Press MUTE to temporarily turn off the
sound.
|
The MUTE mark
is displayed.
Press MUTE or VOL (+)/(–) to turn the
sound back to the previous level.
|
The MUTE mark
disappears.
VOLUME
30
Note:
I MUTE is automatically cleared when the
following button is pressed: ON/OFF,
VOL (+)/(–) or MUTE.
ON/OFF Standby
To turn off the LCD monitor
ON/OFF
ON/OFF
MUTE
MENU
Press ON/OFF.
The POWER indicator turns red.
AV INPUT
SELECT
SELECT
To turn the LCD monitor back on
VOL
VOL
Press ON/OFF again.
The POWER indicator turns green.
LCD MONITOR
13
SELECTING THE MENU ITEMS
Selecting the Menu Items
• This LCD monitor set allows you to adjust the picture, sound, and other features using the On-screen
Display. Select the desired menu item by following the steps below and then refer to the indicated page
for details.
1 Press MENU to display the MENU
(Pages 16 and 17)
VOL
(+)/( )
screen.
ON/OFF
MUTE
PICTURE(AV1)
[
[
[
[
[
[
[
[
30]
0]
CONTRAST
TINT
2 Press SELECT (])/([) to select
MENU
AV INPUT
the desired menu item.
0]
COLOR
SELECT
SELECT
MENU
0]
BLACK LEVEL
SHARPNESS
RED-BLUE
GREEN
• The cursor moves up or down.
• The cursor indicates the selected
menu item.
0]
0]
0]
VOL
VOL
N358]
COLOR SYSTEM
RESET
SELECT
(])/([)
3 Press VOL (+)/(–) to enter.
SELECT:
ENTER: –VOL+
EXIT: MENU
4 Press MENU again to exit.
(Pages 18 and 19)
SET UP
MENU
LCD MONITOR
[BRIGHT
]
BRIGHTNESS
UPSIDE
PICTURE
SET UP
LANGUAGE
[NORMAL]
[NORMAL]
RIGHT/LEFT
BLUE SCREEN
AV1
AV2 IN/OUT
SLEEP TIMER
[OFF
]
[NORMAL]
[IN
]
[ – – – REMAIN]
SELECT:
ADJUST: –VOL+ EXIT: MENU
SELECT:
ENTER: –VOL+
EXIT: MENU
(Page 15)
LANGUAGE
ENGLISH
Notes:
ESPAÑOL
FRANÇAIS
I The displayed items differ depending
on the setting conditions.
I The selected item is highlighted in
yellow.
I Items in purple cannot be selected.
I The original screen is restored by
pressing MENU on the menu screen
or any of the adjustment screens.
The original screen is also restored
when no buttons have been pressed
for about a period of 30 seconds.
The adjustment values and settings
that were changed before the screen
is restored are saved as is in the
memory.
SELECT:
EXIT: MENU
* The screen indications shown above are larger than actual size for easy reading.
14
ADJUSTMENT
Adjusting the LANGUAGE Settings
MENU on the LCD monitor set can also be used to select the language.
1 Press MENU to display the MENU
VOL
(+)/( )
MENU
ON/OFF
screen.
PICTURE
MUTE
SET UP
LANGUAGE
2 Press SELECT (])/([) to move the
MENU
AV INPUT
cursor to LANGUAGE, and then press
VOL (+)/(–) to display the LANGUAGE
screen.
SELECT
SELECT
MENU
VOL
VOL
SELECT
(])/([)
SELECT:
ENTER: –VOL+
EXIT: MENU
3 Press SELECT (])/([) to select the
LANGUAGE
ENGLISH
LCD MONITOR
language you want to display.
ESPAÑOL
FRANÇAIS
4 Press MENU again to exit.
SELECT:
EXIT: MENU
15
ADJUSTMENT (Continued)
Adjusting the PICTURE Settings
1 Press MENU to display the MENU
MENU
VOL
(+)/( )
screen.
ON/OFF
PICTURE
MUTE
MENU
SET UP
LANGUAGE
2 Press SELECT (])/([) to move the
cursor to PICTURE, and then press
VOL (+)/(–) to display the PICTURE
screen.
AV INPUT
SELECT
SELECT
MENU
VOL
VOL
SELECT:
ENTER: –VOL+
EXIT: MENU
SELECT
(])/([)
PICTURE(AV1)
CONTRAST
TINT
[
[
[
[
[
[
[
[
30]
0]
3 Press SELECT (])/([) to move the
cursor and select the desired
adjustment item.
0]
COLOR
LCD MONITOR
0]
BLACK LEVEL
SHARPNESS
RED-BLUE
GREEN
COLOR SYSTEM
RESET
0]
All items that can be adjusted are
shown in the table on the next page.
0]
0]
N358]
4 Press VOL (+)/(–) to display the screen
SELECT:
ENTER: –VOL+
EXIT: MENU
for the selected adjustment item.
5 Press VOL (+)/(–) to make the
adjustment.
COLOR
0
–
+
ADJUST: –VOL+ EXIT: MENU
SELECT:
6 Press MENU again to exit.
16
ADJUSTMENT (Continued)
Adjusting the PICTURE Settings (Continued)
Selected item
CONTRAST
TINT
Press VOL (–).
Press VOL (+).
Increase contrast
Toward green
Higher color intensity
Increase brightness
Sharp picture
Decrease contrast
Toward purple
COLOR
Lower color intensity
Decrease brightness
Soft picture
BLACK LEVEL
SHARPNESS
RED-BLUE
GREEN
More red
More blue
Less green
More green
COLOR SYSTEM
Press VOL (+)/(–) to select COLOR SYSTEM.
Note:
I TINT is displayed only when N358 or N443 is selected.
Switching the COLOR SYSTEM
Set the system to N358 for normal reception.
When the picture is not stable, switching to an appropriate system may improve the picture quality.
17
ADJUSTMENT (Continued)
Adjusting the SET UP Settings
The SET UP items can be set by the user.
1 Press MENU to display the MENU
MENU
VOL
(+)/( )
screen.
ON/OFF
PICTURE
MUTE
MENU
SET UP
LANGUAGE
2 Press SELECT (])/([) to move the
AV INPUT
cursor to SET UP.
SELECT
SELECT
MENU
VOL
VOL
SELECT:
ENTER: –VOL+
EXIT: MENU
SELECT
(])/([)
3 Press VOL (+)/(–) to display the SET
SET UP
UP screen.
[BRIGHT
]
BRIGHTNESS
UPSIDE
[NORMAL]
[NORMAL]
RIGHT/LEFT
BLUE SCREEN
AV1
4 Check the factory setting of each item
on the SET UP screen.
LCD MONITOR
[OFF
]
[NORMAL]
[IN
]
AV2 IN/OUT
SLEEP TIMER
The user can change the settings with
SELECT (])/([) and VOL (+)/(–).
[ – – – REMAIN]
SELECT:
ADJUST: –VOL+ EXIT: MENU
5 Press MENU again to exit.
Selected item
Factory setting
Setting change
BRIGHTNESS
[BRIGHT] Maximum brightness [NORMAL] Brightness 60% → Suitable for viewing in well-lit areas.
Saves energy.
[DARK]
Brightness 20% → Sufficiently bright when viewing in
dim areas.
UPSIDE
[NORMAL] Normal vertical
image orientation
[DOWN] Inverted image → To display images upside down for
special applications.
A B C
RIGHT/LEFT
[NORMAL] Normal horizontal
image orientation
[MIRROR] Mirror image → To display mirror images for special
applications.
B C
A B C
BLUE SCREEN
[OFF]
This feature is
inactive.
[ON]
The screen is turned blue when there is no signal.
AV1
[NORMAL]
[IN]
[COMPONENT]
AV2 IN/OUT
[OUT
[OUT
]
Line Output is selected, Output volume is fixed, Speaker
output is available.
] Line Output is selected, Output volume is variable,
Speaker output is Mute.
[ – – – REMAIN]
The setting can be specified in increments of 30 minutes and in a
range between 30 and 120 minutes. (see page 19)
SLEEP TIMER
Note:
I In BLUE SCREEN, PICTURE setting displayed in purple cannot be selected.
18
ADJUSTMENT (Continued)
Adjusting the SLEEP TIMER Settings
1 Press MENU to display the MENU
MENU
VOL
ON/OFF
PICTURE
MUTE
screen.
(+)/( )
SET UP
LANGUAGE
MENU
AV INPUT
2 Press SELECT (])/([) to move the
cursor to SET UP, and then press VOL
(+)/(–) to display the SET UP screen.
SELECT
SELECT
MENU
VOL
VOL
SELECT:
ENTER: –VOL+
EXIT: MENU
SELECT
(])/([)
3 Press SELECT (])/([) to move the
cursor to SLEEP TIMER, and then
press VOL (+)/(–) to set SLEEP TIMER
(in minutes).
SET UP
[BRIGHT
]
BRIGHTNESS
UPSIDE
[NORMAL]
[NORMAL]
RIGHT/LEFT
BLUE SCREEN
AV1
AV2 IN/OUT
SLEEP TIMER
LCD MONITOR
[OFF
]
[NORMAL]
[IN
]
The setting can be specified in
increments of 30 minutes and in a
range between 30 and 120 minutes.
The setting is turned off when --- is
displayed.
[ – – – REMAIN]
SELECT:
ADJUST: –VOL+ EXIT: MENU
4 Press MENU again to exit.
Note:
I If the monitor’s power is turned off and then
turned back on again after the SLEEP TIMER
has been set, the setting will be canceled.
19
CONNECTING TO EXTERNAL DEVICES
Connecting to a VCR, a DVD Player, etc. (AV 1/2 IN)
This LCD monitor can be connected to most external devices as shown below.
When connecting to an external device, turn off the power of the main unit and then connect to the device
to prevent any possible damage.
AV 2 IN/OUT
AUDIO
AV 1 IN
S-VIDEO
VIDEO
AUDIO
VIDEO
COMPONENT
R
L
R
L
Y
PB
PR
Video cord
Audio cord
(BNC TYPE)
S-video cord
To AUDIO input
terminal
To VIDEO input
terminal
To S-VIDEO input
terminal
To AUDIO input
terminal
To VIDEO input
terminal
Audio cord
Video cord
(BNC TYPE)
To audio output
terminal
To video output
terminal
Audio Audio
(R) (L)
Video
Audio Audio
Video
S-Video
To audio output
terminal
To S-Video
output terminal
To video output
terminal
(R)
(L)
/
VCR, Laser disc player, etc.
DVD Player, etc.
* For improved picture quality from video
sources with COMPONENT output, use
the connection diagram on page 21.
Notes:
I PC connection is not possible.
I Use a commercially available audio/video cord for the cable.
I When connecting or disconnecting the video cord (BNC TYPE) to or from the VIDEO input terminal, disconnect the
audio cable.
I Only connect audio/video signals to AV 1/2 IN terminals. Connecting other signals may result in a malfunction.
I When external devices are connected to both the VIDEO and S-VIDEO terminals (and AV1 is selected), priority is
given to the S-VIDEO input terminal. To view images from the VIDEO input terminal, do not connect any cable to the
S-VIDEO terminal.
I For details concerning the usage and connection of external devices, see their respective instruction manuals.
20
CONNECTING TO EXTERNAL DEVICES (Continued)
Connecting to a DVD player (COMPONENT terminal)
AV 2 IN/OUT
AUDIO VIDEO
AV 1 IN
S-VIDEO
AUDIO
VIDEO
COMPONENT
R
L
R
L
Y
PB
PR
To AUDIO
input terminal
To COMPONENT
terminal
Audio cord
Video cord
(BNC TYPE)
To audio
output terminal
To COMPONENT
terminal
Y
PB
Audio
(R)
Audio
(L)
PR
DVD Player
Note:
I To view the image from the component connected to the terminals for AV 1 IN, set AV1 to COMPONENT with the
SET UP setting (see page 18).
21
CONNECTING TO EXTERNAL DEVICES (Continued)
Outputting video and audio (video output)
It is possible to output video and audio from the set through the AV output terminals (AV 2 IN/OUT).
AV 2 IN/OUT
AUDIO VIDEO
AV 1 IN
S-VIDEO
AUDIO
VIDEO
COMPONENT
PB
R
L
R
L
Y
P
R
Connect a VCR, Audio amplifies, etc
Notes:
I AV2 can be set to input or output. When set to input, output is not possible and vice versa.
I When using COMPONENT and/or S-VIDEO terminal, it is not possible to output video, but it is possible to output
audio for connecting to audio systems.
Listening with Headphones
I Plug the headphone mini-plug into the headphone jack located on the front side of the set.
ꢀ On-screen display
Mini-plug
MENU
HEAD
PHONE
HEADPHONE
jack
VOLUME
60
Headphones
Notes:
I The headphones are not included in the supplied accessories.
I No sound will be heard from the main unit speakers when the headphones are connected.
Fixing the Cables
• Secure cables and cords with the supplied
cable clamps so that they do not get caught
when mounting the cover.
• Connect the cables and cords after affixing the
cable clamps (2 positions) close to the AUDIO
input terminal and the POWER INPUT terminal.
Cable clamps
22
CONNECTING TO EXTERNAL DEVICES (Continued)
Watching TV
To view a TV broadcast on the LCD monitor, the set-top box must be used with a TV tuner, satellite tuner
or VCR. Refer to the diagram below for wiring.
TV
ROOM ANTENNA
TERMINAL
SET-TOP BOX
MONITOR
TV BROADCAST
(ON AIR)
AUDIO
VIDEO
R
L
(BNC TYPE)
TV ANT
RF IN
VCR
VIDEO OUT
AUDIO
VIDEO
R
L
(BNC TYPE)
TV ANT
RF IN
TV TUNER
VIDEO OUT
PAY TV
AUDIO
VIDEO
R
L
(BNC TYPE)
CABLE
RF IN
RF IN
RF IN
SET-TOP BOX
VIDEO OUT
SATELLITE TV
AUDIO
VIDEO
R
L
(BNC TYPE)
SATELLITE
SATELLITE TUNER
VIDEO OUT
WEB TV
AUDIO
VIDEO
R
L
TV ANT
(BNC TYPE)
TEL, LINE
Web
SET-TOP BOX
VIDEO OUT
23
TROUBLESHOOTING
Problem
Check item
Pages
• Make sure that the AC power cord plug is securely
inserted in AC power outlet and AC adapter.
• Make sure that the AC adapter’s DC output is securely
connected to main unit’s DC input terminal.
• Make sure that the main power switch of the main unit is
on.
• Make sure that the AV input is properly set.
• Make sure that the cables are correctly connected to
rear terminal section of LCD monitor.
8
12
12
No image on screen, and
no sound from speakers.
• Check to see if the batteries in the remote control have
sufficient power.
8
• Make sure that the unit is not in the standby mode
(power indicator is red).
13
• Make sure that the cables are correctly connected.
• Make sure that AV1 is set to COMPONENT to view
the image from component sources.
20, 21
18
Speakers produce sound,
but no image on screen.
• Check COLOR and TINT adjustments. (NTSC ONLY)
• Check CONTRAST and BLACK LEVEL adjustments.
• Check RED-BLUE adjustments.
17
17
• Make sure that the DVD connection cord is correctly
connected to the COMPONENT terminal.
Image is too light or
improperly tinted.
• Make sure that the cables are properly connected to
rear terminal section of LCD monitor.
• Check the volume adjustment.
• Make sure that the sound is not muted.
• Make sure that the headphones are not connected.
13
13
22
Image is displayed, but no
sound from speakers.
• Check to see if BRIGHTNESS is set to DARK.
• Check CONTRAST and BLACK LEVEL adjustments.
• Lamp may have reached the end of its life. (Contact
an authorized Sharp service facility for replacement
lamp(s).)
18
17
Image is too dark.
• Check COLOR adjustment.
• Check the color system setting.
17
17
• Make sure that the DVD connection cord is correctly
connected to PB and PR of the COMPONENT terminal.
No colors on image.
• Check to see if the batteries in the remote control
have sufficient power.
• Make sure that (+) and (–) side of batteries are
properly positioned in remote control.
• Make sure that the remote sensor window is not
under strong fluorescent lighting.
8
8
Remote control does not work.
24
SPECIFICATIONS
ITEMS
Panel
LC-20M4U
20” Black TFT LCD
LCD
Number of dots
Low reflection
Brightness
921,600 (640 × 3 × 480) dots
Non-glare
430 cd/m2
Viewing angles
Left to right 160°
Upper to lower 160°
40,000 hours (at normal mode)
Lamp Life
COLOR SYSTEM System
N358/N443/PAL/PAL-M/PAL-N/PAL-60/SECAM
4.0 W (0.7 W × 2 + 2.6 W)
AUDIO
Output
Speaker
Full range 1.2 × 1.6 in. (3 × 4 cm) Oval, 2 pcs.
Woofer 3.1 in. (8 cm) Round, 1 pc.
TERMINALS
AV 1 IN
Video Composite (BNC TYPE), S-Video,
Audio R/L
Component input, Y/PB/PR (BNC TYPE)
Video Composite (BNC TYPE), Audio R/L
0.1 in. (3.5 mm) ø jack
AV 2 IN/OUT
Headphone jack
POWER SUPPLY DC operation
AC operation
DC 13 V, Typical: 3.0 A, Max: 3.8 A
AC 110~240 V, 50/60 Hz with AC adapter
AC 120 V, Typical: 50 W, Standby: 0.5 W
Silver
Power consumption
Exterior color
APPEARANCE
Outside dimensions
18.1 (W) × 17.2 (H) × 7.3 (D) in.
(460 (W) × 437.5 (H) × 186 (D) mm)
Net weight
19.0 lbs (8.6 kg), incl. stand, excl. accessories
13.4 lbs (6.1 kg), excl. stand
ACCESSORIES
Operation manual
Remote control
Language: English/French/Spanish/Portuguese
Infrared wireless type
(Infrared carrier frequency: 38 kHz)
AC adapter
Multi-Voltage type, 1 pc.
DC cable: 6.5 ft (2 m)
DC power converter:
2.6 (W) x 1.5 (H) x 5.5 (D) in.
(67 (W) x 37 (H) x 140 (D) mm)
AC cord
6.1 ft (1.85 m), 1 pc.
Batteries
“AAA” size (UM/SUM-4) Dry Battery × 2 pcs.
2 pcs.
Cable clamp
OSD LANGUAGE Language
English/French/Spanish
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of
production units. There may be some deviations from these values in individual units.
25
DIMENSIONAL DRAWINGS
Unit: inch/mm
18.1/460
MAIN
POWER
POWER
SLEEP
2.0/52
7.3/186
26
Calling for Service
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or customer
assistance, please call 1-800-BE-SHARP.
LIMITED WARRANTY
END-USER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this Sharp brand product (the
“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it
will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured
equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or
other misuse, abnormal service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide
proof of purchase to the servicer.
To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and exclusive of, all other
warranties, express or implied. Specifically, ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE
EXCLUDED. ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR USE, AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, under
applicable state law, implied warranties may not validly be disclaimed or excluded, the duration of such implied warranties is
limited to the period(s) from the date of purchase set forth below.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused
by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any
way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on
warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply.
Model Specific Section
Your Product Model Number & Description:
LC-20M4U LCD AV MONITOR
(Be sure to have this information available when you need service for
your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from
Warranty Coverage (if any):
None
Where to Obtain Service:
From a Sharp Authorized Servicer located in the United States.
To find the location of the nearest Sharp Authorized Servicer, call
Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Be sure to have Proof of Purchase available. If you ship the Product,
be sure it is insured and packaged securely.
TO OBTAIN PRODUCT INFORMATION, CALL 1-888-LCD-SHARP.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
OSAKA, JAPAN
LIMITED WARRANTY
Information Systems Products
Congratulations on your purchase!
Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express warranty to the first consumer purchaser for this
Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer:
Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If any such
defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the product as
specified herein.
This warranty shall not apply to:
(a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate
use as outlined in the owner’s manual.
(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp’s Authorized Service Centres
or Sharp’s Authorized Servicing Dealers.
(c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited to
software, toner, paper and batteries.
(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including but
not limited to AC adapters, ribbon, correction tape, printwheel, ink rollers, toner, developer, drum, cables, paper, filters, software.
(e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.
(f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or liquid
spillage.
(g) Any product received without appropriate model, serial number and CSA/cUL markings.
(h) Any products used for rental purposes.
(i) Any installation, setup and/or programming charges.
Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp product
together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an
Authorized Sharp Servicing Dealer.
This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee is
authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all
liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting from a
defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product or the loss
of information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs incurred. Correction of
defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations and responsibilities of Sharp
to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict
liability or otherwise.
WARRANTY PERIODS
Personal Copier
3 years
Personal Facsimile
1 year
High End Personal Computer
LCD Projectors (XG & PG Series)
LCD Monitor
3 years (rechargeable battery 1 year)
3 years (bulb 90 days)
1 year
Laser Printer
1 year
Inkjet Printer
1 year
Open Line Electronic Cash Register
6 months
To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:
SHARP ELECTRONICS OF CANADA LTD.
SHARP ELECTRONICS OF CANADA LTD
335 Britannia Road East
Mississauga, Ontario
L4Z 1W9
(905) 568-7140 or 1 (877) SHARP-CC
VALID IN CANADA ONLY
|