Sharp Home Theater Server PN ZS701 User Manual

TIPS  
Back  
The supplied clamps can be attached to the stand rods and shelf board  
bar to hold the cables.  
Clamp position  
Clamp  
Operation Manual  
TROLLEY STAND PN-ZS701  
Specifications  
Applicable models (as of September 2011) LCD MONITOR PN-L702B  
(Available models differ according to region.)  
Units: mm (inch)  
Model  
PN-ZS701  
(Note that the values shown are approximate values.)  
Height  
4 positions  
Thank you for purchasing a SHARP product.  
adjustment  
Center height of the screen  
Approx. 1310 mm (51-9/16 inch) [A],  
approx. 1210 mm (47-5/8 inch) [B],  
approx. 1110 mm (43-11/16 inch) [C],  
approx. 1010 mm (39-3/4 inch) [D]  
(Depends on the position of the mounting  
brackets attached in Step 1-(4).)  
See the diagram at right  
Before using the product, please be sure to read this operation manual carefully. In particular, be sure to read the section “To  
ensure safe and correct use”. After reading the manual, keep it in a convenient location where it can be accessed at any time.  
TIPS  
- This product was shipped after strict quality control and inspection; however, if breakage or a malfunction should be found,  
contact your SHARP dealer or your nearest customer contact.  
- Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a  
third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is  
recognized under law.  
Dimensions  
Weight  
Approx. 48 kg (105.8 lbs.)  
- This product and its accessories may be upgraded without advance notice.  
As a part of our policy of continuous improvement, SHARP  
reserves the right to make design and specification changes  
for product improvement without prior notice. The  
performance specification figures indicated are nominal  
values of production units.  
To ensure safe and correct use  
This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays and labels  
and incorrectly using the product could have results as classified below.  
There may be some deviations from these values in individual  
units.  
Please read the following warning symbol information before reading the rest of this section, and be sure to strictly observe all  
instructions.  
Not following these instructions could result  
in death or serious injury.  
Not following these instructions could result  
in injury or property damage.  
Warning:  
Caution:  
1980 (77-15/16)  
• The installation must be performed by qualified service  
personnel.  
• Do not climb onto or lean on the stand and monitor.  
Toppling may occur, causing injury.  
Improper installation work may cause the monitor to fall or  
topple over, resulting in injury.  
• If deformation or cracks are discovered, stop using the  
stand.  
• Do not place the stand on an unstable surface.  
Do not subject to intense shock or vibration.  
Toppling or falling may occur, causing injury.  
Using the stand without repairing the problem may cause  
the monitor to fall or the stand to topple, resulting in injury.  
• Take suitable preventative measures to reduce the risk  
of this product falling or toppling due to an earthquake  
or other circumstances.  
• Only use this product with specified models. Do not  
modify the stand or the accessories.  
Otherwise, the monitor may fall or the stand may topple  
over, resulting in injury.  
The equipment for preventing falling and toppling will not  
be effective if the wall or table to which the equipment is  
attached is not sufficiently strong. Reinforce the wall or  
table sufficiently. These measures to prevent falling and  
toppling are intended to reduce the risk of injury and other  
harm, however, their effectiveness is not guaranteed in all  
earthquakes.  
• Lock the casters when using the stand.  
Toppling may occur, causing injury.  
• Do not transport the stand with a monitor attached.  
If the monitor mounting attachments become broken or  
damaged, the monitor may fall or the stand may break or  
topple, resulting in injury.  
• Use the supplied screws. Tighten all screws firmly.  
Insufficient tightening may cause the monitor to fall or the  
stand to topple over, resulting in injury.  
Printed in China  
TINSE1212MPZZ(1)  
– 4 –  
– 1 –  
 

Shark Vacuum Cleaner uvc805 User Manual
Sharp PDAs Smartphones OZ 630 User Manual
Sony Cassette Player WM FX153 User Manual
Sony Speaker System SA VA15 User Manual
Sony Stereo Amplifier TA F501ES User Manual
Sony Stereo System CMT EP414 User Manual
Stiga Outdoor Storage 107 M User Manual
Subaru Robin Power Products Automobile Parts EY15 2B User Manual
Sunbeam Blender PB9800 User Manual
Tanaka Cultivator TMC 200 User Manual