Sharp Speaker System HT SB20 User Manual

Controls and indicators (continued)  
System preparation  
Accessories  
The following accessories are included.  
ENGLISH  
1
To mount the sound bar on the wall  
Rear Panel  
2
Make a hole on the wall following the screw  
point marks on the pattern paper by using  
a drill.  
MODEL  
1. DC In Jack  
Caution:  
2. Audio In Jack  
Be very careful to prevent the sound bar [5.07 lbs.  
(2.3 kg)] from falling when mounting on the wall.  
Before mounting, check the wall strength. (Do not  
put on the veneer plaster or whitewashed wall. The  
sound bar may fall.) If unsure, consult a qualied  
service technician.  
1-1/4” (32 mm)  
HT-SB20  
HT-SB30  
Remote control x 1  
(RRMCGA326AWSA: HT-SB20)  
(RRMCGA322AWSA: HT-SB30)  
AC/DC adaptor x 1  
(RADPAA096AWZZ)  
AC power cord x 1  
(QACCDA005AWZZ)  
3/8” (8-9 mm)  
Wall surface  
Mounting screws are not supplied. Use appropri-  
ate ones.  
SOUND BAR HOME THEATER SYSTEM  
3
4
Fix a wall mount plug into the hole using  
a hammer, until it is ush with the wall  
surface.  
2
Check all wall mount angle screws for looseness.  
Select a good location. If not, accidents may occur  
or the sound bar may get damaged.  
SHARP is not responsible for accidents result-  
ing from improper installation.  
1
2
Remote Control  
OPERATION MANUAL  
ON/  
MUTE  
STAND-BY  
1-1/4” (32 mm)  
Audio cable x 1  
(QCNWGA087AWPZ)  
Pattern paper x 1  
(TCAUHA034AWZZ)  
12  
13  
1. Remote Control Transmitter  
2. Mute Button  
3. Cinema (Sound Mode) button  
4. Music (Sound Mode) button  
5. Surround Button  
6. Bypass (Sound Mode) button  
7. TV Operation Buttons  
8. Bluetooth Pairing Button (HT-SB30 only)  
9. Bluetooth Play/Pause Button (HT-SB30  
only)  
SOUND MODE  
MUSIC  
CINEMA  
NEWS  
INPUT  
3
4
5
6
3/8” (8-9 mm)  
Wall surface  
Driving screws  
SHARP designed the sound bar so you may hang  
it on the wall. Use proper screws (not supplied).  
The illustrations printed in this manual are for the model HT-SB30.  
BYPASS SURROUND  
14  
ON/  
Y
D-B  
AN  
ST  
TE  
MU  
DE  
MO  
ND  
OU  
NE  
WS  
S
SIC  
MU  
TV  
A
EM  
CIN  
Controls and indicators  
UT  
INP  
UND  
RRO  
SU  
SS  
PA  
BY  
TV  
Fastenthescrewstothewallasshownbelow.  
(Total screw is 2 pieces)  
CH  
See below for size and type.  
L
VO  
VOL  
CH  
7
Front Panel (HT-SB20)  
L
VO  
1 2 3 4  
5 6  
7 8  
1/8” (3.2 mm)  
1. On/Stand-by  
Indicator  
2. On/Stand-by  
Button  
3. Surround Button  
4. Surround Indicator  
5. Volume Indicator  
6. Volume Down  
Button  
7. Volume Up Button  
A
WS  
2A  
32  
GA  
MC  
RR  
Screw using  
Screwdriver  
8
9
3/16”  
(5 mm)  
8. Remote Sensor  
9. Left Channel  
Speakers  
10. Bluetooth Skip Up Button (HT-SB30 only)  
11. Bluetooth Skip Down Button (HT-SB30  
only)  
3/8” (9 mm)  
VOL  
15  
10  
11  
Wall surface  
Min. 7/8” (22 mm)  
10. Right Channel  
Speakers  
SOUND BAR HOME THEATER SYSTEM HT-SB20  
12. On/Stand-by Button  
13. News (Sound Mode) button  
14. Input Button (HT-SB30 only)  
15. Volume Up/Down Buttons  
4.5mm - 5mm  
RRMCGA322AWSA  
Installing the sound bar  
Gap from  
wall surface  
Wall surface  
SOUND BAR HOME THEATER SYSTEM HT-SB20  
Note:  
Remote control  
1
Fix the pattern paper to the wall in hori-  
zontal position as below.  
Plastic shield  
Before using remote control, please remove plastic  
shield at battery holder.  
9
10  
6 7 8 9 10  
5
Hang the sound bar onto the screws.  
509 mm  
Wall  
surface  
(HT-SB30 only)  
548 mm  
Front Panel (HT-SB30)  
44 mm  
1 2 3 4 5  
The Bluetooth® word mark and logos are registered trademarks owned by  
Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other  
trademarks and trade names are those of their respective owners.  
Battery holder  
TV Operation Buttons (Only SHARP TV):  
1. On/Stand-by  
Indicator  
2. On/Stand-by  
Button  
10. Remote Sensor  
11. Left Channel  
Speakers  
Note: This product is recommended for at panel TV (LED, LCD and plasma).  
Pattern paper  
(supplied)  
12. Right Channel  
Speakers  
On/Stand-  
by Button  
Volume Up  
and Down  
Buttons  
Sets the TV power to  
“ON” or “STAND-BY”.  
Turn up/down the TV  
volume.  
Input Select  
Button (TV)  
Channel Up and  
Down Buttons  
Press the button to  
switch the input source.  
Switch up/down the TV  
channels.  
SOUND BAR HOME THEATER SYSTEM HT-SB30  
3. Input Button  
4. Pairing Button  
5. Pairing Indicator  
6. Surround Indicator  
7. Surround Button  
8. Volume Down  
Button  
Caution: Before operating this product, refer “IMPORTANT SAFEGUARDS AND  
WARRANTY” at the reverse page of English operation manual.  
VOL  
CH  
SOUND BAR HOHEATEEM HT-SB30  
9. Volume Up Button  
Note:  
Some models of SHARP TV may not be operable.  
SHARP TV remote control will not work with HT-SB20/HT-SB30 system.  
11  
12  
Printed in Malaysia  
13A R AS 1  
*TINSZB425AWZZ2-*|  
E-1  
E-2  
E-3  
TINSZB425AWZZ  
When mounting on the wall  
Sound bar connections to TVs  
Placing the sound bar  
Installation image:  
AC power connection  
Screw eye (not supplied)  
Notes:  
After checking all the connections have  
been made correctly, connect the AC  
power cord to the AC power input jack,  
then to the AC outlet.  
Caution:  
Make sure to unplug the AC power  
cord before making any connections.  
Remove the protective lm covering the sound  
Turn off all other equipment before making any connections.  
Safety wires (not  
supplied)  
bar before turning on the system.  
The front panel of the sound bar is not  
removable.  
TV  
Notes:  
To connect to TV, use Audio IN terminals located at the rear of the sound bar.  
Refer the operation manual of the equipment to be connected.  
Fully insert the plugs to avoid fuzzy pictures or noises.  
Place the  
sound  
bar as  
shown.  
AC/DC Adaptor  
Caution:  
2
Using with the AC/DC adaptor  
SOUND BAR HOME THEATER SYSTEM HT-SB30  
Cable  
Do not change the installation direction when  
In some cases, a small background noise could emit from the sound bar, when you  
use the RCA audio output terminal connection from a TV-Set/DVD/Blu-ray Disc  
Player. In such case, please change the connection to the headphone terminal  
connection. This effect depends on the used TV/DVD/Blu-ray Disc Player-Brand,  
model and age, and it is not a quality matter from the sound bar.  
If the TV volume is continuously at low level, the sound bar will automatically  
power off. Increase the TV output volume to enjoy the sound from the speaker.  
the sound bar is turned on.  
Do not stand or sit on the sound bar as you  
may be injured.  
1 Plug the AC power cord into the AC/  
DC adaptor.  
2 Plug the AC/DC adaptor cable into  
the DC INPUT jack on the sound  
bar.  
DC IN jack  
(DC 17V)  
Sound bar  
Wall  
AC power cord  
DVD player  
3 Plug the AC power cord into an AC  
VCR  
1
AC outlet  
outlet.  
Connecting a TV, or DVD player, etc.  
When placing on the shelf/table  
AC/DC Adaptor  
(AC 100 - 240 V ~ 50/60 Hz)  
Notes:  
Falling prevention  
Safety wires (not supplied) are useful to prevent the sound bar from falling.  
If the TV/monitor has an audio output, connect it to the Audio IN jack on the rear  
of the sound bar.  
During power standby, the stand-by  
indicator turns RED. If ON-STANDBY  
button is pressed, the STAND-BY  
indicator turns BLUE.  
Unplug the AC/DC adaptor from the  
AC outlet if the sound bar will not be  
used for a prolonged period of time.  
Use only the supplied AC/DC adaptor.  
Using other AC/DC adaptor may  
cause an electric shock or re.  
Sound bar  
HT-SB30  
To select AUDIO IN function:  
Press INPUT button repeatedly.  
To select Bluetooth function:  
Press INPUT button repeatedly. (PAIRING indicator turns blue.)  
TV  
Screw eye  
(not supplied)  
To audio output terminals  
Safety  
Rack/  
table  
wires  
(not  
supplied)  
Screw eye  
(not supplied)  
or  
To HEADPHONE  
terminal  
Blu-Ray/DVD player/  
Digital Tuner  
Audio cable  
Audio cable  
(not supplied)  
To AUDIO  
IN jack  
Sound bar  
E-4  
E-5  
E-6  
E-7  
Listening to Bluetooth enabled devices (for HT-SB30) (continued)  
General control  
Remote control  
Listening to Bluetooth enabled devices (for HT-SB30)  
ON/STAND-BY  
PAIRING  
Audio stream  
Precautions for battery use:  
5
Select “SHARP HT-SB30” from the source  
list. If Passcode* is required, enter “0000”.  
Pairing indicator (blue) on the sound bar will  
stop blinking once the sound bar is success-  
fully paired with the source device. Pairing  
information is now memorized in the sound  
bar.  
To turn the power on  
Press the ON/STAND-BY button.  
The STAND-BY indicator turns BLUE.  
Sound Mode  
About Bluetooth technology  
Battery installation  
O
N
/
S
T
A
N
D
-
B
Y
S
O
U
R
C
E
PAIRING  
SURROUND  
-
VOLUME  
+
SOUND BAR HOME THEATER SYSTEM HT-SB30  
Remove the battery if the sound bar will  
not be used for a long period of time.  
This will prevent potential damage due  
to battery leakage.  
O
N
/
S
T
A
N
D
-
B
Y
S
O
U
R
C
E
PAIRING  
SURROUND  
-
VOLUME  
+
Bluetooth wireless technology is a short-range radio  
technology that enables wireless communication  
between various types of digital devices, such  
as mobile phone or computer. It operates within  
a range of about 10 meters (30 feet) without the  
hassle of having to use cables to connect these  
devices. Since the Bluetooth technology does not  
require line of sight between the communicating  
devices, it is not necessary to line up the transmit-  
ting device and the receiver, as in the case of infra  
red technology.  
This product contains a CR Coin  
Lithium Battery which contains Per-  
chlorate Material – special handling  
may apply, California residents, see  
chlorate/  
Remote control operation:  
Press the desired sound mode button  
on the remote control.  
SOUND BAR HOME THEATER SYSTEM HT-SB30  
Bluetooth mobile phone or other  
Bluetooth Stereo audio source device  
Note:  
If the power does not turn on, check whether  
the power cord is plugged in properly.  
Pairing with other Bluetooth  
Caution:  
HT-SB20  
Do not use rechargeable battery  
(nickel-cadmium battery, etc.).  
Danger of explosion if battery is in-  
correctly replaced.  
source device  
Pairing Bluetooth devices  
The VOLUME indicator: blinking  
HT-SB30  
To set the sound bar to stand-by mode:  
Press the ON/STAND-BY button again. The  
STAND-BY indicator turns RED.  
* Passcode may be called PIN Code, Passkey,  
PIN number or Password.  
1
2
3
Press the ON/STAND-BY button to turn the  
power on.  
Bluetooth devices need to be initially paired rst  
before they can exchange data. Once paired, it is  
not necessary to pair them again unless:  
1
While pushing the locking tab to-  
wards the center of the remote con-  
trol, slide out the battery holder.  
Replace only with the same or  
equivalent type.  
The SURROUND indicator: blinking  
6
Start the Bluetooth connection from the  
source device.  
Some audio source devices may connect with  
the sound bar automatically, otherwise follow  
the instructions in the source device operating  
manual to start connection.  
Press the INPUT button to select Bluetooth  
function. (PAIRING indicator blinks.)  
Volume auto fade-in  
If you turn off and on the sound bar again,  
volume will start at lower level and gradually  
increase to the last set level.  
CINEMA (for cinema sound effect)  
MUSIC (for standard sound effect)  
Batteries (battery pack or batteries  
installed) shall not be exposed to ex-  
cessive heat such as sunshine, re  
or the like.  
pairing is made with more than 8 devices.  
Pairing can only be made one device at  
a time. This sound bar can be paired to a  
maximum of 8 devices. If subsequent device  
is paired, the oldest device paired, will be de-  
leted and replaced with the new one.  
Back of  
remote control  
Press and hold the PAIRING button for 1  
second or more.  
NEWS  
(for news)  
Communication System and Bluetooth Prole  
of this sound bar  
There are many available Bluetooth Profiles  
describing the basic communication methods,  
specic functions and uses, to enable communica-  
tion between devices.  
Installing the battery incorrectly may  
cause the sound bar to malfunction.  
PAIRING indicator blinks quickly. The sound  
bar is now in pairing mode and is ready to be  
paired with other Bluetooth source device.  
BYPASS (for at sound effect)  
Volume control  
Sound bar operation:  
Press volume up (VOLUME + ) to increase  
the volume and press volume down (VOL-  
UME – ) to decrease the volume.  
Locking  
tab  
Notes concerning use:  
Function  
Notes:  
Replace the battery if the operating  
distance is reduced or if the opera-  
tion becomes erratic. Purchase “CR  
2025”, coin lithium battery.  
this sound bar is reset. All pairing information  
is deleted when sound bar is reset.  
pairing information is deleted while repairing, etc.  
If this sound bar or the source device is turned  
Note:  
2
Remove the old battery from the  
battery holder, insert the new bat-  
tery and then slide the battery hold-  
er back into the remote control.  
HT-SB20  
off before Bluetooth connection is completed,  
pairing will not be completed and the pairing  
information will not be memorized. Repeat  
step 1 onwards to start pairing again.  
To pair with other devices, repeat steps 1 - 5  
for each device.  
This sound bar can be paired to a maximum  
of 8 devices. If subsequent device is paired,  
the oldest device paired, will be deleted and  
replaced with the new one.  
Pairing indicator (blue) will stop blinking once  
the sound bar is successfully paired with the  
source device.  
When the sound bar is connected to the TV/  
DVD, etc., the AUDIO IN function is ready  
to be used.  
This sound bar supports the following:  
Communication System: Bluetooth Specication  
version 2.1 Bluetooth + Enhanced Data Rate  
(EDR) Prole : A2DP (Advanced Audio Distribu-  
tion Prole)  
A2DP enables audio streaming from an A2DP  
equipped Bluetooth stereo audio source device  
(eg mobile phone) to this sound bar. By convert-  
ing wireless stereo audio signal to analogue audio  
signal, you can enjoy listening to the sound through  
this speaker system.  
Periodically clean the transmitter on  
the remote control and the sensor  
on the sound bar with a soft cloth.  
Exposing the sensor on the sound  
bar to strong light may interfere with  
operation. Change the lighting or the  
direction of the sound bar if this oc-  
curs.  
On indicators  
Remote control operation:  
Press the VOL + button to increase the  
volume and the VOL – button to decrease  
the volume.  
Status  
PAIRING indicator (blue)  
Blinks  
4
Perform pairing procedure on the source  
device to detect this sound bar. (Refer  
the source device operating manual for  
details).  
“SHARP HT-SB30” will appear in the detected  
devices list (if available) in the source device.  
Positive (+)  
side up  
Battery holder  
HT-SB30  
Unconnected  
Pairing mode  
Connected  
Polarity  
(+) symbol  
When the INPUT button is pressed, the input  
source will change.  
Blinks quickly  
Lights up  
Note:  
When volume is maximum or minimum:  
Battery type  
Locking tab  
1
2
Audio In Function - the pairing indicator turns  
off.  
HT-SB20  
Keep the remote control away from  
moisture, heat, shock, and vibra-  
tions.  
Bluetooth Function - the pairing indicator  
turns blue.  
Notes:  
The VOLUME indicator: blinking  
HT-SB30  
Once  
a
device is ousted or deleted from  
Place the devices to be paired within 1 me-  
ter (3 feet) of each other when pairing.  
Note:  
the pairing list, the pairing information for  
the device is also deleted. To listen to the  
sound from the device again, it needs to be  
re-paired. Perform steps 1 - 5 to pair the de-  
vice again.  
Passcode of this sound bar is xed to “0000”  
and can only be paired with Bluetooth source  
device whose passcode is also “0000”.  
The backup function will protect the memorized  
function mode for a few hours should there be  
a power failure or the AC power cord becomes  
disconnected.  
The SURROUND indicator: blinking  
AVRCP (Audio/Video Remote Control Prole) is a  
technology that allows a single remote control to  
control all Bluetooth enabled Audio Video equip-  
ment to which a user has access.  
Some source devices are unable to display  
lists of detected devices. To pair this sound  
bar with the source device, refer to the  
source device operating manual for details.  
Muting  
The volume is muted temporarily when pressing  
the MUTE button on the remote control. Press  
again to restore the volume.  
Auto power on function:  
When stand-by indicator is VIOLET, the sound  
bar will automatically power ON if it detects  
audio signal from connected equipment,  
unless it is turned off manually (STAND-BY  
indicator turns red).  
Notes when using unit with a mobile phone  
This unit cannot be used to talk over the tele-  
phone even when there is a Bluetooth con-  
nection made to a mobile phone.  
Please refer to the operating manual supplied  
with the mobile phone for details on operation  
of your mobile phone while transmitting the  
sound using a Bluetooth connection.  
Surround  
When the SURROUND button is pressed, the  
SURROUND sound is ON. (SURROUND indicator  
turns ORANGE)  
Auto power off and auto detect signal:  
The sound bar will automatically go to stand-  
by mode (STAND-BY indicator turns violet) if  
no audio signal is detected within 20 minutes.  
E-8  
E-9  
E-10  
E-11  
Listening to Bluetooth enabled devices (for HT-SB30) (continued)  
Troubleshooting chart  
Troubleshooting chart  
Maintenance  
Specications  
Many potential problems can be resolved by the  
owner without calling a service technician.  
If something is wrong with this product, check the  
following before calling your authorized SHARP  
dealer or service center.  
Cleaning the cabinet  
As part of our policy of continuous improvement,  
SHARP reserves the right to make design and  
specication changes for product improve-  
ment without prior notice. The performance  
specication gures indicated are nominal  
values of production unit. There may be some  
deviations from these values in individual unit.  
Listening to the sound  
To nish listening  
Condensation  
Bluetooth sound  
Is the sound bar  
too near to a device  
that generates  
Error indicators and  
warnings  
When you fail to perform operations properly, the fol-  
lowing messages are displayed on the sound bar.  
is interrupted or  
distorted.  
Periodically wipe the cabinet with a soft cloth.  
Check that:  
Sudden temperature changes, storage or operation  
in an extremely humid environment may cause con-  
densation inside the cabinet or on the transmitter  
on the remote control.  
Condensation can cause the sound bar to malfunc-  
tion. If this happens, leave the power on until normal  
operation is possible (about 1 hour). Wipe off any  
condensation on the transmitter with a soft cloth  
before operating the sound bar.  
Perform any of the followings.  
- Terminate the Bluetooth connection on the audio  
source device.  
Refer the operating manual supplied with the  
device.  
- Turn off the Bluetooth stereo audio source  
device.  
- Turn off this sound bar.  
Caution:  
The source device Bluetooth functionality is ON.  
Pairing of this sound bar and the source device  
is completed.  
(HT-SB30)  
electromagnetic  
radiation?  
Do not use chemicals for cleaning (petrol, paint  
thinner, etc.). It may damage the cabinet nish.  
Is there any obstacle  
between the sound  
bar and the Bluetooth  
stereo audio source  
device?  
Do not apply oil to the inside of each component.  
It may cause malfunctions.  
Display  
Meaning  
General  
Any device connected to the AUDIO IN socket  
is turned off.  
General  
When the protection circuit  
is activated.  
Symptom  
Possible cause  
Power indica-  
tor (blinks red)  
1
Press the ON/STAND-BY button to turn the  
power on.  
Power source DC IN 17V  
2.8A: AC/DC  
No sound is heard.  
Is the input signal  
(selection) set  
adaptor  
Factory reset, clearing all  
2
3
4
Press the INPUT button to select Bluetooth  
(*): Should the same message appear even if  
the sound bar is unplugged and plugged in  
or is set to the stand-by mode and on again,  
contact your local dealer where you purchased  
the sound bar.  
Note:  
(AC 100 - 240V ~ 50/60Hz)  
O
N
/
S
T
A
N
D
-
B
Y
S
O
U
R
C
E
PAIRING  
SURROUND  
-
VOLUME  
+
Remote control  
properly?  
setting  
SOUND BAR HOME THEATER SYSTEM HT-SB30  
function.  
The volume of this sound bar may not be controlled  
as intended depending on the device.  
Is the volume level set  
to minimum?  
Is muting activated?  
Are the connections  
made correctly?  
Is the sound bar too  
far from the Bluetooth  
stereo audio source  
device? (HT-SB30)  
Is the sound bar paired  
with the Bluetooth  
stereo audio source  
device? (HT-SB30)  
Power  
consumption  
10W  
Start the Bluetooth connection from the  
Bluetooth stereo audio source device.  
Symptom  
Possible cause  
Make sure to disconnect all audio input cables  
attached to the sound bar before performing the  
factory reset.  
The remote control  
does not operate  
properly.  
Is the battery polarity  
correct?  
Is the battery dead?  
Is the distance or angle  
incorrect?  
Are there any  
obstructions in front of  
the sound bar?  
Is there a strong light  
shining on the remote  
sensor?  
Is the remote control  
for another equipment  
used simultaneously?  
Start playing on the Bluetooth stereo audio  
source device.  
Maximum  
RMS: Total 40 Watts  
Bluetooth operation buttons  
(remote control only)  
output power 20 Watts per channel into  
6 ohms at 1 kHz, 10% total  
harmonic distortion  
1. Unplug the AC power cord.  
Notes:  
2.  
HT-SB20  
If the source device has an extra bass function  
or equalizer function, set them to off. If these  
functions are on, sound may be distorted.  
Press the button to play or pause.  
FTC: Minimum 14 watts  
per channel into 3 ohms at  
100 Hz to  
20 kHz, 1% total harmonic  
distortion  
Press and hold ON/STAND-BY button  
and the SURROUND button and plug the  
AC power cord.  
Press the button to skip up.  
Notes:  
Press the button to skip down.  
You need to make the Bluetooth connection  
HT-SB30  
again if:  
Press and hold ON/STAND-BY button  
and the PAIRING button and plug the AC  
power cord.  
Speaker  
2-way Speaker System  
2-1/4” (5.7cm) Woofer  
1” (2.5cm) Soft Dome  
- the sound bar is not turned on.  
Noise is heard  
during playback.  
Move the sound  
bar away from any  
computers or mobile  
phones.  
- the source device is not turned on, or its Blue-  
tooth functionality is off or is in sleep mode.  
If both the Bluetooth connected device and the  
one connected to the AUDIO IN are played  
simultaneously, only the Bluetooth sound can  
3. Press the ON/STAND-BY button  
Input  
terminals  
Analog input (AUDIO IN):  
Stereo mini jack Ø 3.5mm  
500mV / 47kohms  
Caution:  
The sound bar  
cannot be turned  
on with the remote  
control.  
Is the AC power cord  
of the sound bar  
When a button  
is pressed, the  
sound bar does not  
respond.  
Set this sound bar to  
the stand-by mode and  
then turn it back on.  
If the sound bar still  
malfunctions, reset it.  
(Refer to page 7.)  
This operation will erase all data stored in  
memory.  
be heard.  
plugged in?  
Frequency  
Band  
(HT-SB30)  
2.4 GHz band (2,400GHz  
- 2,480GHz)  
Is the battery inserted?  
If problem occurs during  
TV cannot be  
operated with the  
remote control.  
Depending on the  
model, some or all  
operation  
Compatible  
Bluetooth  
Prole  
A2DP (Advanced Audio  
Distribution Prole), AVRCP  
(Audio/Video Remote Control  
Prole)  
When this product is subject to strong external  
interference (mechanical shock, excessive static  
electricity, abnormal supply voltage due to light-  
ning, etc.) or if it is operated incorrectly, it may  
malfunction.  
functions may not be  
operable using the  
remote control of this  
sound bar. In this case,  
use the remote control  
supplied with the TV.  
The power is not  
turned on.  
Is the sound bar  
unplugged? (Refer to  
page 10)  
(HT-SB30)  
Bluetooth 2.1 +EDR  
The protection circuit  
may be activated.  
Unplug and plug in the  
power cord again after  
5 minutes or more.  
If such a problem occurs, do the following:  
Dimensions  
Weight  
Width: 37” (940mm)  
Height: 2-7/8” (73mm)  
Depth: 3-1/4” (83mm)  
1
Set the sound bar to the stand-by mode and  
turn the power on again.  
2
If the sound bar is not restored in the previous  
operation, unplug and plug in the sound bar,  
and then turn the power on.  
5.07lbs. (2.3kg)  
E-12  
E-13  
E-14  
E-15  
HT-SB30_EN_SPECIAL_NOTES_A2.indd1 1  
 
2013-01-07 06:55:01  

Shure Headphones 440 User Manual
Shure Microphone MX100 Series User Manual
Sony Digital Camera DSC F55V User Manual
Sony Microphone ECM Z60 User Manual
Spalding Fitness Equipment M7819241 User Manual
Sun Microsystems Server iPlanet Web Server User Manual
SUPER MICRO Computer Computer Hardware AOC USAS S4I User Manual
SVA Computer Monitor 9005W B User Manual
Sylvania CRT Television 6420FD User Manual
Sylvania Home Safety Product LUMI083 User Manual