ENGLISH
MODEL
(
)
( )
XL-HF201P BK / XL-HF301P T
HI FI COMPONENT SYSTEM
OPERATION MANUAL
XL-HF201P(BK) Hi Fi Component System consisting of XL-HF201P(BK) (main unit) and CP-HF200 (speaker system).
XL-HF301P(T) Hi Fi Component System consisting of XL-HF301P(T) (main unit) and CP-HF301 (speaker system).
XL-HF201
XL-HF301
“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic
accessory has been designed to connect specifically to iPod, iPhone, or iPad,
respectively, and has been certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note that the use of this
accessory with iPod, iPhone, or iPad may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and
iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries. iPad is
a trademark of Apple Inc.
Accessories
Please confirm that the following accessories are included.
CD/USB
Adaptors for
iPhone x 3
GCOVAA238AWSA
GCOVAA239AWSA
GCOVAA294AWSA
Remote control
x 1
RRMCGA264AWSA
AM loop antenna
x 1
QANTL0005AWZZ
FM antenna x 1
FANT1535A
Speaker wires x 2
QCNWHA035AWPZ
(for XL-HF301P(T))
QCNWHA041AWPZ
(for XL-HF201P(BK))
Stand for iPad x 1
GITAUA014AW01
The illustrations printed in this operation manual are for the model XL-HF201P(BK).
Special Note
Supply of this product does not convey a license nor imply any right to distribute content created with this product in
revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), revenue generating
streaming applications (via Internet, intranets and/or other networks), other revenue-generating content distribution
systems (pay-audio or audio-on-demand applications and the like) or on revenue-generating physical media (compact
discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An independent license for
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.
Printed in Malaysia
12D R KI 1
TINSZB282AWZZ
XL-HF201P_HF301P_US_cover.indd
1
3/7/2012 11:09:00 AM
SPECIAL NOTES
NOTE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation.If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
ꢀ
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
ꢀ
ꢀ
ꢀ
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
WARNING
FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by
the manufacturer could void the user’s authority to operate
this equipment.
This product is classified as a CLASS 1 LASER PRODUCT
Caution - Use of any controls, adjustments or procedures
other than those specified herein may result in hazardous
radiation exposure.
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss or theft,
please record below the model number and serial number which
are located on the rear of the unit. Please retain this information.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the National Electrical Code that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable
entry as practical.
Model number
Serial number
..............................................
..............................................
Date of purchase ..............................................
Place of purchase ..............................................
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but
it can also cause personal injuries and property damage
if improperly handled. This product has been engineered
and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or
fire. In order to prevent potential danger, please observe
the following instructions when installing, operating and
cleaning the product. To ensure your safety and prolong
the service life of this product, please read the following
precautions carefully before use.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong.The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinchedparticularlyatplugs,conveniencereceptacles,
and the point where they exit from the apparatus.
E-1
XL-HF201P_HF301P_US.indd
1
3/7/2012 10:35:19 AM
IMPORTANT SAFETY INSTRUCTIONS (continued)
11) Only use attachments/accessories specified by the
manufacturer.
20) Safety Check - Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
21) Wall or ceiling mounting - When mounting the product
on a wall or ceiling, be sure to install the product
according to the method recommended by the
manufacturer.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
22) Power Lines - An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can
fall into such power lines or circuits. When installing
an outside antenna system, extreme care should
be taken to keep from touching such power lines or
circuits as contact with them might be fatal.
23) Outdoor Antenna Grounding - If an outside antenna
or cable system is connected to the product, be sure
the antenna or cable system is grounded so as to
provide some protection against voltage surges and
built-up static charges. Article810 of the National
Electrical Code, ANSI/NFPA 70, provides information
with regards to proper grounding of the mast and
supporting structure, grounding of the cord-in wire to
an antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding
electrode.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Additional Safety Information
15) Power Sources - This product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or
local power company. For product intended to operate
from battery power, or other sources, refer to the
operating instructions.
16) Overloading - Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
17) Object and Liquid Entry - Never push objects of
any kind into this product through openings as they
may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock.
To prevent fire or shock hazard, do not expose this
appliance to dripping or splashing. No objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Example of antenna grounding asper
National Electrical Code, ANSI/NFPA 70
ANTENNA CORD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART250, PARTH)
18) Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
NEC - NATIONAL ELECTRICAL CODE
S2898A
24) Protective Attachment Plug - The product is equipped
with an attachment plug having overload protection.
This is a safety feature. See Instruction Manual
for replacement or resetting of protective device.
If replacement of the plug is required, be sure the
service technician has used a replacement plug
specified by the manufacturer that has the same
overload protection as the original plug.
25) Stand - Do not place the product on an unstable
cart, stand, tripod or table. Placing the product on an
unstable base can cause the product to fall, resulting
in serious personal injuries as well as damage to the
product. Use only a cart, stand, tripod, bracket or
table recommended by the manufacturer or sold with
the product. When mounting the product on a wall,
be sure to follow the manufacturer’s instructions. Use
only the mounting hardware recommended by the
manufacturer.
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen
into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in
any way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
19) Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
E-2
XL-HF201P_HF301P_US.indd
2
3/7/2012 10:35:20 AM
For U.S. customer only
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the
"Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will,
at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent
at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or
other misuse, abnormal service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide
proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law.
ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE
LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused
by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any
way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion
of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
XL-HF201P(BK) / XL-HF301P(T) HI FI COMPONENT SYSTEM
(Be sure to have this information available when you need
service for your Product.)
One (1) year parts and labor from the date of purchase.
Warranty Period for this Product:
Non-functional accessories, supplies, and consumable
items.
Additional Item(s) Excluded from Warranty Coverage
(if any):
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer,
call Sharp toll free at 1-800-BE-SHARP.
Where to Obtain Service:
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized
Servicer. Be sure to have Proof of Purchase available. If
you ship the Product, be sure it is insured and packaged
securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
System connections
ꢀ
ꢀ
Do not expose the unit to moisture, to temperatures higher than 140˚F
(60˚C) or to extremely low temperatures.
If your system does not work properly, disconnect the AC power cord
from the AC outlet. Plug the AC power cord back in, and then turn on
your system.
In case of an electrical storm, unplug the unit for safety.
Hold the AC power plug by the head when removing it from the AC outlet,
as pulling the cord can damage internal wires.
The AC power plug is used as a disconnect device and shall always
remain readily operable.
ꢁ Precautions
ꢀ
Please ensure that the equipment is positioned in a well ventilated area
and ensure that there is at least 4” (10 cm) of free space along the sides,
top and back of the equipment.
ꢀ
ꢀ
4” (10 cm)
4” (10 cm)
4” (10 cm)
ꢀ
ꢀ
ꢀ
Do not remove the outer cover, as this may result in electric shock.
Refer internal service to your local SHARP service facility.
4” (10 cm)
Use the unit on a firm, level surface free from vibration.
Place the speakers at least 12” (30 cm) away from any CRT TV to avoid
color variations across the TV screen. If the variations persist, move
the speakers further away from the TV. LCD TV is not prone to such
variation.
This unit should only be used within the range of 41˚F
(5˚C - 35˚C).
-
95˚F
ꢀ
ꢀ
Warning:
The voltage used must be the same as that specified on this unit. Using this
product with a higher voltage other than that which is specified is dangerous
and may result in a fire or other type of accident causing damage. SHARP will
not be held responsible for any damage resulting from use of this unit with a
voltage other than that which is specified.
ꢀ
ꢀ
Keep the unit away from direct sunlight, strong magnetic fields, excessive
dust, humidity and electronic/electrical equipment (home computers,
facsimiles, etc.) which generate electrical noise.
Do not place anything on top of the unit.
E-3
XL-HF201P_HF301P_US.indd
3
3/7/2012 10:35:20 AM
System connections (continued)
Make sure to unplug the AC power cord before making any connections.
Installing the AM loop antenna
< Attaching
to the wall >
AM loop
antenna
Right
speaker
< Assembling >
Wall
screws (not supplied)
Video cable (not supplied)
To video input jack
Left
speaker
FM antenna
AC outlet
(AC 120 V ~ 60 Hz)
Red
Black
ꢁ Volume control
ꢁ Line input connection (TV, etc.)
The sound level at a given volume setting depends on speaker efficiency,
location and various other factors. It is advisable to avoid exposure to high
volume levels, which occurs while turning the unit on with the volume control
setting up high, or while continually listening at high volumes. Excessive sound
pressure from earphones and headphones can cause hearing loss.
Connect to the TV using an audio cable.
To audio
output jack
TV
ꢁ Speaker connection
Audio cable
(commercially
available)
For XL-HF201P(BK)
ꢀ
Connect the black wire to the minus (–) terminal,
and the red wire to the plus (+) terminal.
For XL-HF301P(T)
ꢀ
Connect the wire without insulation tube to the
minus (–) terminal, and the wire with red insulation
tube to the plus (+) terminal.
Incorrect
ꢀ
ꢀ
Use speakers with an impedance of
4
ohms or
more, as lower impedance speakers can damage the unit.
Do not mistake the right and the left channels. The right speaker is the
one on the right side when you face the unit.
ꢀ
ꢀ
Do not let the bare speaker wires touch each other.
Do not allow any objects to fall into or to be placed in the bass reflex
ducts.
To LINE input
jack
ꢀ
Do not stand or sit on the speakers.You may be injured.
Main unit
ꢁ Subwoofer pre-out connection
You can connect a subwoofer with an amplifier to the SUBWOOFER PRE
OUT jack.
Commercially available subwoofer
(amplifier built in)
Audio cable
(commercially
available)
Audio signal
To audio
input jack
To select Line In function:
ꢀ
On main unit: Press FUNCTION button repeatedly until Line In is
To SUBWOOFER
PRE OUT jack
displayed.
Main unit
ꢀ
On remote control: Press AUDIO/LINE (INPUT) button repeatedly until
Line In is displayed.
Notes:
ꢀ
ꢀ
No sound is heard from the subwoofer without a built-in amplifier.
Subwoofer Pre-out (audio signal): 200mV / 10k ohms at 70 Hz.
E-4
XL-HF201P_HF301P_US.indd
4
3/7/2012 10:35:20 AM
ꢁ Auto power off function
Remote control
The main unit will enter the stand-by mode (when iPod or iPhone is not
docked) after 15 minutes of inactivity during:
ꢁ Battery installation
iPod: No connection.
CD / USB: In the stop mode.
AUDIO IN / LINE IN: No detection of input signal or very low sound audibility.
Use a “AA” size battery (UM/SUM-3, R6, HP-7 or similar). Battery
are not included.
1
Open the battery cover.
Note:
2
Insert the battery according to the direction indicated in the battery
compartment.
However, if iPod or iPhone is docked, the unit will begin charging.
“Charge Mode” will be displayed.
When inserting or removing the battery, push them toward the
battery terminals.
Close the battery cover.
ꢁ Muting
3
The volume is muted temporarily when pressing the
control. Press again to restore the volume.
button on the remote
ꢁ X-Bass control
When the power is first turned on, the unit will enter the extra bass mode which
emphasizes the bass frequencies, and “X-Bass On” will appear. To cancel the
extra bass mode, press the X-BASS button on the remote control.
Caution:
ꢀ
Remove the battery if the unit will not be used for a long period of time.
This will prevent potential damage due to battery leakage.
Do not use rechargeable battery (nickel-cadmium battery, etc.).
Installing the battery incorrectly may cause the unit to malfunction.
Battery (battery pack or battery installed) shall not be exposed to
excessive heat such as sunshine, fire or the like.
ꢀ
ꢀ
ꢀ
ꢁ Bass control
1
2
Press the BASS/TREBLE button to select “Bass”.
Within 5 seconds, press the VOLUME (+ or -) button to adjust the bass.
Notes concerning use:
ꢀ
Replace the battery if the operating distance is reduced or if the operation
becomes erratic. Purchase a “AA” size battery (UM/SUM-3, R6, HP-7 or
similar).
ꢁ Treble control
1
Press the BASS/TREBLE button to select “Treble”.
ꢀ
ꢀ
ꢀ
Periodically clean the transmitter on the remote control and the sensor
on the unit with a soft cloth.
2
Within 5 seconds, press the VOLUME (+ or -) button to adjust the treble.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit.
Keep the remote control away from moisture, heat, shock, and
vibrations.
ꢁ Function
When the FUNCTION button on main unit is pressed, the current function will
change to different mode. Press the FUNCTION button repeatedly to select
desired function.
General control
CD
FM STEREO
FM MONO
ꢁ To turn the power on
The first time the unit is plugged in, the unit will enter the demonstration mode.
Audio In
iPod
USB
Line In
Function
Main unit
Remote control
Operation
Note:
Power
on/off
Press to turn the power
on or to go to stand-by
mode.
The backup function will protect the memorized function mode for a few hours
should there be a power failure or the AC power cord becomes disconnected.
Demo
on/off
Press to enter to
demonstration on or
off mode.
Listening to the iPod, iPhone or iPad
Made for:
____
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
iPod touch (4th generation)
iPod touch (3rd generation)
iPod touch (2nd generation)
iPod touch (1st generation)
iPod classic
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
iPod nano (3rd generation)
iPod nano (2nd generation)
iPhone 4
iPhone 3GS
iPhone 3G
ꢁ Display brightness control
To dim the display brightness, press the DEMO/DIMMER button on the
remote control.
Dimmer 1
Dimmer 2
Dimmer off
(Display is dim).
iPod nano (6th generation)
iPod nano (5th generation)
iPod nano (4th generation)
iPhone
iPad
(Display gets dimmer).
(Display is bright).
ꢁ Volume auto fade-in
Caution:
If you turn off and on the main unit with the volume set to 27 or higher, the
volume starts at 16 and fades in to the last set level.
Please update your iPod, iPhone and iPad unit to the latest software
version before using it. Please visit Apple’s homepage to download the
latest version for your iPod, iPhone and iPad.
ꢁ Volume control
Notes:
Turn the volume knob toward VOLUME +/- (on main unit) or press VOL
+/- (on remote control) to increase or decrease the volume.
ꢀ
Charging terminal for iPod, iPhone and iPad:
Condition
USB function
DOCK
NO
USB
YES
NO
ꢁ Auto power on function
When you press any of the following buttons, the unit turns on.
Other function
Stand-by
YES
YES
ꢀ
iPod, CD, USB, AUDIO / LINE (INPUT), TUNER on the remote control:
Selected function is activated.
NO
ꢀ
button on the main unit: The unit turns on and playback of the last
function will start (CD, TUNER, USB, iPod, AUDIO IN, LINE IN)
E-5
XL-HF201P_HF301P_US.indd
5
3/7/2012 10:35:22 AM
Listening to the iPod, iPhone or iPad (continued)
Adaptor for iPod and iPhone connection
ꢀ
ꢀ
The message “This accessory is not made to work with
iPhone” or similar, may appear on the iPhone screen when:
- battery is low.
Notes:
ꢀ
ꢀ
Please use the adaptor supplied with your iPod or iPhone unit.
You can use an audio cable to connect your iPod to the AUDIO IN
jack if:
- the iPhone is not properly docked (eg. slanting).
If this occurs, remove and re-dock the iPhone.
This product is made for iPod, iPhone and iPad. To
prevent random interference when iPod, iPhone
and iPad is connected, the headphone output is
disabled, and “HP INVALID” will be displayed.
You may also experience brief audio interference during
incoming calls.
1. your iPod adaptor does not fit into the iPod dock on the main
unit.
2. you have an iPod that does not have an iPod adaptor.
3. you have an iPod that does not have an iPod 30 pin connector.
Adaptor No.
iPhone Description
iPhone
Capacity
4GB & 8GB & 16GB
8GB & 16GB
12
15
15
19
ꢁ iPod, iPhone and iPad connection (USB only)
iPhone 3G
1
Insert the connector to the
iPod, iPhone or iPad.
iPhone 3GS
iPhone 4
16GB & 32GB
16GB & 32GB
iPad
Connector
ꢁ To insert adaptor for iPod or iPhone
2
3
Place the iPad to the stand
for iPad.
iPad
1
Open the docking station for iPod and
iPhone by pulling up.
Stand for iPad
Connect the iPod, iPhone
or iPad to the unit via USB
connector.
USB
2
Insert the adaptor for iPod or iPhone into unit and connect your
iPod or iPhone.
iPhone
iPhone (bottom)
Note:
USB terminal does not support VIDEO out.
Dock connector
ꢁ iPod, iPhone or iPad playback
1
2
Press the ON/STAND-BY button to turn the power on.
Press the USB button on the remote control or FUNCTION button
repeatedly on the main unit to select USB function.
Adaptor for iPhone
Dock for iPhone
3
Connect iPod, iPhone or iPad to the unit. “USB/iPod” will appear.
Track number
) button to start playback.
Connector for iPhone
4
Press the
(CD/USB
Caution:
Note
:
Unplug all accessories from the iPod or iPhone before inserting it into
the dock.
Stop button ( ) is invalid during iPod, iPhone or iPad playback.
ꢁ iPhone playback
ꢁ To remove adaptor for iPod or iPhone
ꢀ
Sound will only switch from iPhone to the main unit after
authentication process is completed in approximately 10 seconds.
Insert the tip of a screwdriver (“-” type, small)
into the adaptor hole as shown and lift upward
to remove.
ꢀ
ꢀ
Incoming calls will pause the playback.
Once the calls are answered, the conversation can only be heard
through the built-in iPhone speaker. Turn on the iPhone speaker or
undock the iPhone to start conversation.
ꢁ iPod or iPhone playback
1
2
Press the ON/STAND-BY button to turn the power on.
Press the iPod or iPhone button on the remote control or FUNCTION
button repeatedly on the main unit to select iPod function.
Insert iPod or iPhone unit into the dock of main unit. “DOCK OK”
will appear.
ꢁ iPod and iPhone connection (Dock only)
3
4
Note:
Docking station is not recommended for iPad connection.
Press the
(iPod or iPhone
) button to start playback.
E-6
XL-HF201P_HF301P_US.indd
6
3/7/2012 10:35:22 AM
Listening to the iPod, iPhone or iPad
(continued)
Main unit
Dock/USB
Remote control
Function
Operation
Dock
USB
ꢁ To disconnect iPod, iPhone or iPad
Track up/
down
Press in the playback
or pause mode. If you
press the button in the
pause mode, press the
button to start the
Simply remove the iPod or iPhone from the docking station or iPad
connector from USB terminal. It is safe to do so even during playback.
ꢁ Watching videos on a TV connected to iPod
desired track.
or iPhone
Fast
forward/
reverse
Press and hold down in
the playback mode.
Release the button to
resume playback.
1
2
Press the DISPLAY (TV OUT) button for more than 2 seconds until
“TV OUT ON” appear on display.
Press the ENTER button to start playback.
Display/
Toggle
____
iPod
iPod
CD/USB
Press for more than
2 seconds to toggle
the video out display
between iPod or TV.
Press to toggle repeat
mode.
Notes:
information
display
ꢀ
If the TV Out setting is already turned on at video menu, the video
is automatically displayed on the TV screen when ENTER key is
pressed.
Repeat
Shuffle
Menu
____
____
____
ꢀ
ꢀ
TV out display is not support through USB terminal. (iPad)
Press to toggle shuffle
mode.
To return to watching video on iPod or iPhone screen, press the
MENU button to enter video menu. Then press the DISPLAY (TV
OUT) button for more than 2 seconds until “TV OUT OFF” appears.
iPod
Press to view the iPod
menu during iPod
function.
ꢀ
During iPod or iPhone video playback, pressing the DISPLAY (TV
OUT) button will not toggle video out display between iPod and TV.
Enter
____
____
Press to confirm the
selection.
Caution:
ꢀ
Unplug all accessories for the iPod or iPhone before inserting it into
the docking station.
Cursor
Up/Down
Press to select the iPod
menu.
ꢀ
Stop button ( ) at main unit is invalid during iPod function.
ꢁ
Navigating the iPod, iPhone or iPad menus
1
Press the MENU button to view the menu on iPod, iPhone or iPad
unit. Press it again to go back to previous menu.
Listening to a CD or MP3/WMA disc
2
Use the PRESET (
and then press ENTER button.
or
) button to select an item on the menu
Note:
When navigating the iPod, iPhone or iPad menu with remote control, do
not operate any of the buttons on the iPod or iPhone unit. The volume
level is adjusted by pressing the VOL (+ or -) button on the main unit or
the remote control. Adjusting the volume on the iPod, iPhone or iPad
units give no effect.
iPod, iPhone and iPad operations:
The operations described below depend on the generation iPod, iPhone
and iPad you are using.
ꢁ Disc playback
System on operation:
When the main unit is powered on, the iPod, iPhone or iPad units will
automatically power on when docked or connected in the unit.
1
Press the ON/STAND-BY button to turn the power on.
Press the CD button on the remote control or FUNCTION button
repeatedly on the main unit to select CD function.
Press the OPEN/CLOSE button to open the disc tray.
Place the disc on the disc tray, label side up.
2
System off (stand-by operation):
When the main unit is turned to stand-by mode, the docked iPod, iPhone
or connected iPad unit will automatically turn to stand-by mode.
3
4
5
6
Press the OPEN/CLOSE button to close the disc tray.
Press the
(CD/USB
) button to start playback. After the last
ꢁ Various iPod, iPhone and iPad functions
track is played, the unit will stop automatically.
Notes for CD or MP3/WMA disc:
Main unit
Dock/USB
Remote control
ꢀ
When the end of the last track is reached during fast forward, “END”
will appear on the display and CD operation will be paused. When the
beginning of the first track is reached during fast reverse, the unit will
enter the playback mode (only for CD).
Function
Play
Operation
Dock
iPod
USB
CD/USB
Press in the pause mode.
ꢀ
Rewritable multi-session discs with unfinished writing, can still be
played.
Pause
iPod
CD/USB
Press in the playback
mode.
E-7
XL-HF201P_HF301P_US.indd
7
3/7/2012 10:35:23 AM
Listening to a CD or MP3/WMA disc (continued)
ꢁ Various disc functions
ꢁ Repeat play
Repeat play can play one track, all tracks or a programed sequence
continuously.
Remote
control
Function
Play
Main unit
Operation
Press in the stop mode.
To repeat one track:
Press the REPEAT button repeatedly until “Repeat One” appears. Press
the
To repeat all tracks:
Press the REPEAT button repeatedly until “Repeat All” appears. Press
the (CD/USB ) button.
(CD/USB
) button.
Stop
Press in the playback mode.
Pause
Press in the playback
mode. Press the
button
To repeat desired tracks:
Perform steps 1 - 5 in “Programed play” section on page 8-9 and then
press the REPEAT button repeatedly until “Repeat All” appears.
to resume playback from the
paused point.
Press in the playback or stop
mode.
If you press the button in the
stop mode, press the
button to start the desired track.
Press and hold down in the
playback mode.
Track up/
down
To cancel repeat play:
Press the REPEAT button repeatedly until “Normal” appears and
“
” disappears.
Fast
forward/
reverse
Release the button to resume
playback.
Caution:
After performing repeat play, be sure to press the
Otherwise, the disc will play continuously.
(CD/USB
) button.
ꢁ Random play
The tracks on the disc can be played in random order automatically.
To random play all tracks:
Press RANDOM button on the remote control until “Random” appears. Press
the (CD/USB ) button.
To cancel random play:
Press the RANDOM button again. “RDM” indicator will disappear.
ꢁ Direct track search
By using the Numeric buttons, the desired tracks on the current disc can
be played.
Use the Numeric buttons on the remote control to select the desired
Notes:
ꢀ
If you press the
button during random play, you can move to the track
button
track while playing the selected disc.
selected next by the random operation. On the other hand, the
does not allow you to move to the previous track. The beginning of the
track being played will be located.
ꢀ
ꢀ
The Numeric buttons allow you to select up to number 9.
When selecting number 10 or higher, use the “10+” button.
A. For example, to choose 13
ꢀ
In random play, the unit will select and play tracks automatically. (You
cannot select the order of the tracks.)
1
2
3
Press the “10+” button once.
Press the “1” button.
Press the “3” button.
Selected track number
ꢁ Programed play (CD)
B. For example, to choose 130
You can choose up to 32 selections for playback in the order you like.
1
2
3
4
Press the “10+” button twice.
Press the “1” button.
1
While in the stop mode, press the MEMORY button on the remote
control to enter the programing save mode.
Press the “3” button.
Press the “0” button.
Notes:
ꢀ
A track number higher than the number of tracks on the disc cannot
be selected.
2
Press the numeric button or
select the desired track.
or
buttons on the remote control to
ꢀ
During random play, direct search is not possible.
To stop playback:
Press the (CD/USB ) button.
Selected track number
E-8
XL-HF201P_HF301P_US.indd
8
3/7/2012 10:35:24 AM
ꢁ Procedure to playback MP3/WMA disc
Listening to a CD or MP3/WMA disc
(continued)
with folder mode on
To play back CD-R/RW.
3
4
Press the MEMORY button to save the track number.
1
Press the CD button, and load an MP3/WMA disc. Press the FOLDER
button and disc info will be displayed.
MP3 indicator
Repeat steps 2 - 3 for other tracks. Up to 32 tracks can be programed.
If you want to check the programed tracks, press the MEMORY button
repeatedly. If you make a mistake, the programed tracks can be cleared
by pressing the CLEAR button.
WMA indicator
TOTAL indicator
5
Press the
(CD/USB
) button to start playback.
Total number of folder
Total number of files
ꢁ Programed play (MP3/WMA)
2
Press the PRESET (
(Folder mode on)
FOLDER
or
) button to select desired playback folder.
1
While in the stop mode, press the MEMORY button to enter the
programing save mode.
indicator
2
Press the PRESET (
the desired folder
or
) button on the remote control to select
button on the remote control to select the
FOLDER number
Select desired file to be played back by pressing the
Press the (CD/USB ) button. Playback will start and file name
will be displayed.
First track number in the folder
3
4
or button.
ꢀ
Title, Artist and Album name are displayed if they are recorded on
the disc.
Then press the
desired tracks.
or
ꢀ
In case of playback with the folder mode on, press the PRESET
(
or
) button, and the folder can be selected even though it is
in playback/pause mode. It will continue playback/pause mode in the
1st track of the selected folder.
3
4
Press the MEMORY button to save the folder and track number.
ꢀ
Display content can be changed by pressing the CD/USB DISPLAY
button.
Repeat steps
programed.
2
-
3
for other folder/tracks. Up to 32 tracks can be
File name display
Folder display
5
Press the
(CD/USB
) button to start playback.
To cancel the programed play mode:
During programed stop mode, press the (CD/USB ) button.The display will
show “Memory Clear” and all the programed contents will be cleared
Title display
Counter display
Album display
Artist display
Note:
Adding tracks to the program:
If “Not Support” is displayed, it means “Copyright protected WMA file” or “Not
supported playback file” is selected.
If a program has been previously stored, the “MEM” indicator will be displayed.
Press the MEMORY button. Then follow steps 2 - 3 to add tracks.
Notes:
Listening to USB mass storage
device/MP3 player
ꢀ
When a disc is ejected, the program is automatically canceled.
ꢀ
If you press the ON/STAND-BY button to enter the stand-by mode or
change the function from CD to another, the programed selections will
be cleared.
ꢀ
During the program operation, random play is not possible.
Note:
This product is not compatible with MTP and AAC file systems from USB mass
storage device or MP3 player.
E-9
XL-HF201P_HF301P_US.indd
9
3/7/2012 10:35:25 AM
ꢀ
ꢀ
External HDD-storage cannot be played back via USB terminal.
Listening to USB mass storage device/
MP3 player (continued)
If the data inside the USB memory is large, it may take longer time for
the data to be read.
ꢀ
This product can play WMA and MP3 files. It will automatically detect the
file type being played. If unplayable file is played on this product, “Not
Support” is indicated and the file will be automatically skipped. This will
take a few seconds. If abnormal indications appear on the display due to
the unspecified file, turn off the unit and then turn it on again.
ꢁ To play back USB/MP3 player with folder
mode off
1
Press the USB button on the remote control or FUNCTION button
repeatedly on main unit to select USB function. Connect the USB
memory device that has MP3/WMA format files on the unit. When the
USB memory is connected to the main unit, the device information will
be displayed.
Select desired file to be played back by pressing the
button.
ꢀ
ꢀ
This product relates to USB mass storage devices and MP3 players. It
may however face some irregularities due to various unforeseen reasons
from some devices. Should this happen, turn off the unit and then turn
it on again.
2
3
or
During CD function, MP3 player will not be charging.
Press the
(CD/USB
) button. Playback will start and the file
name will be displayed.
ꢀ
ꢀ
Title, Artist and Album name are displayed if they are recorded in
the USB memory device.
Display content can be changed by pressing the CD/USB DISPLAY
button.
Advanced USB playback
The following functions are the same as CD operations:
Page
Note:
To pause playback:
Press the (CD/USB
Direct track search.......................................................................................8
Repeat play ...................................................................................................8
Random play.................................................................................................8
Programed play ........................................................................................ 8-9
) button.
Note:
ꢁ To play back USB/MP3 player with folder
If USB memory device is not connected, “USB No Media” will be shown on
the display.
mode on
1
Press the USB button on the remote control or FUNCTION button
repeatedly on main unit to select USB function. Connect the USB
memory device that has MP3/WMA format files on the unit. When the
USB memory is connected to the main unit, the device information will
be displayed.
Notes:
ꢀ
ꢀ
ꢀ
ꢀ
This unit only supports “MPEG-1 Audio Layer-3” format. (Sampling
Frequency is 32, 44.1, 48kHz)
Playback order for MP3 files may differ depending on the writing software
used during file download.
2
Press the FOLDER button, and press the PRESET (
or
) button to
Bitrate which is supported by MP3 is 32~320 kbps, WMA is 64~160
kbps.
select desired playback folder. To start playback with folder mode on, go
to step 4. To change the playback folder, press the PRESET (
button to select another folder.
or
)
For MP3/WMA files, please put “.MP3”“.WMA” extension. Files cannot be
played back if there is no MP3/WMA extension.
3
4
Select desired file to be played back by pressing the
Press the (CD/USB
name will be displayed.
or
button.
ꢀ
ꢀ
ꢀ
ꢀ
Playlists are not supported on this unit.
This unit can display Folder Name or File Name up to 32 characters.
Maximum total number of MP3/WMA files is 65025.
) button. Playback will start and the file
Total number of folders read is 999 including folder with non-playable file.
However, the display shows only folder with MP3/WMA files.
ꢀ
Title, Artist and Album name are displayed if they are recorded in
the USB memory device.
ꢀ
ꢀ
The display playback time may not be displayed correctly when playing
back a variable bitrate file.
ꢀ
Display content can be changed by pressing the CD/USB DISPLAY
button.
The ID3TAG information supported are TITLE, ARTIST and ALBUM only.
Title name, artist name and album name can be displayed by pressing
the DISPLAY button during file playback or pause mode.
ꢁ To remove USB memory device
1
Press the (CD/USB ) button to stop playback.
ꢀ
WMA meta tag also supports title, artist and album name which are
recorded in WMA files. Copyright protected WMA files cannot be played
back.
2
Disconnect USB memory device from the USB terminal.
Notes:
ꢀ
SHARP will not be held liable for the loss of data while the USB memory
device is connected to the audio system.
ꢀ
Files compressed in MP3 and/or WMA format can be played back when
connected to the USB terminal.
ꢀ
ꢀ
This USB memory’s format supports FAT 16 or FAT 32.
SHARP cannot guarantee that all USB memory devices will work on this
audio system.
ꢀ
USB cable is not recommended for use in this audio system to connect to
USB memory device. Use of the USB cable will affect the performance of
this audio system. iPod, iPhone and iPad is not prone to this condition.
ꢀ
ꢀ
This USB memory cannot be operated via USB hub.
The USB terminal in this unit is not intended for a PC connection but is
used for music streaming with a USB memory device.
E-10
XL-HF201P_HF301P_US.indd 10
3/7/2012 10:35:25 AM
4
5
Within 30 seconds, press the MEMORY button to store that station in
memory. If the “MEMORY” and preset number indicators disappear
before the station is memorized, repeat the operation from step 2.
Listening to the radio
Repeat steps 1 - 4 to set other stations, or to change a preset station.
When
a
new station is stored in the memory, the station previously
memorized for that preset channel number will be erased.
Note:
The backup function protects the memorized stations for a few hours should
there be a power failure or the AC power cord become disconnected.
ꢁ To recall a memorized station
1
Press the PRESET (
the desired station.
or
) button for less than 0.5 seconds to select
ꢁ To scan the preset stations
The stations saved in the memory can be scanned automatically. (Preset
memory scan)
1
Press the PRESET (
preset number will flash and the programed stations will be tuned in
sequentially, for 5 seconds each.
or
) button for more than 0.5 seconds. The
ꢁ Tuning
2
Press the PRESET (
is located.
or
) button again when the desired station
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TUNER button repeatedly to select the desired 2 frequency
band (FM or AM).
ꢁ To erase entire preset memory
3
Press the TUNING (
the desired station.
or
) button on the remote control to tune in to
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
While pressing down the
until “Tuner Clear” appears.
button, press the ON/STAND-BY button
ꢀ
Manual tuning:
Press the TUNING (
desired station.
or
) button repeatedly to tune in to the
) button is pressed for more than 0.5
FUNCTION ON/STAND-BY
ꢀ
Auto tuning:
When the TUNING (
or
seconds, scanning will start automatically and the tuner will stop at
the first receivable broadcast station.
Setting the clock (Remote control only)
Notes:
ꢀ
When radio interference occurs, auto scan tuning may stop automatically
at that point.
ꢀ
ꢀ
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING (
or
) button again.
To receive an FM stereo transmission:
ꢀ
Press the TUNER button to select stereo mode and “ST” indicator will be
displayed. “ ” and “ ” will appear when an FM broadcast is in stereo.
ꢀ
If the FM reception is weak, press the TUNER button to extinguish
the “ST” indicator. The reception changes to monaural, and the sound
becomes clearer.
ꢁ Memorising a station
You can store 40 AM and FM stations in memory and recall them at the push
of a button. (Preset tuning)
In this example, the clock is set for the 12-hour (AM 12:00) display.
1
2
3
Press the ON/STAND-BY button to turn the power on.
Press the CLOCK/TIMER button.
1
2
Perform steps 1 - 3 in “Tuning”.
Press the MEMORY button.
Within 10 seconds, press the ENTER button.To adjust the day, press the
or
button and then press the ENTER button.
4
Press the
press the ENTER button.
or button to select 24-hour or 12-hour display and then
3
Within 30 seconds, press the PRESET (
preset channel number. Store the stations in memory, in order, starting
with preset channel 1.
or
) button to select the
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 23:59)
The 24-hour display will appear.
(0:00 - 23:59)
E-11
XL-HF201P_HF301P_US.indd 11
3/7/2012 10:35:26 AM
6
7
8
9
To adjust the day, press the
the ENTER button.
or
button and then press
Setting the clock (Remote control only)
(continued)
Press the ENTER button to adjust the hour. Press the
or
button and then press the ENTER button.
5
6
To adjust the hour, press the
ENTER button. Press the
or
button and then press the
To adjust the minutes, press the
press the ENTER button.
Set the time to finish as in steps 7 and 8 above.
or
button and then
or
button once to advance the time
by 1 hour. Hold it down to advance continuously.
To adjust the minutes, press the or button and then press the
ENTER button. Press the or button once to advance the time
by 1 minute. Hold it down to advance the time by 5 minutes interval.
10 Adjust the volume using theVOLUME control, and then press
the ENTER button. Do not turn the volume up too high.
11 Press the ON/STAND-BY button to enter the power stand-by
mode. The “TIMER” indicator lights up and the unit is ready
for timer playback.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will appear for about 5
seconds.
Note:
When power supply is restored after unit is plugged in again or after a power
failure, reset the clock (pages 11).
To readjust the clock:
Perform “Setting the clock” from step 1. If the “Clock” does not appear in step
2, step 4 (for selecting the 24-hour or 12-hour display) will be skipped.
12 When the preset time is reached, playback will start. The
volume will increase gradually until it reaches the preset
volume. The timer indicator will blink during timer playback.
To change the 24-hour or 12-hour display:
13 When the timer end time is reached, the system will enter the
power stand-by mode automatically.
1
Clear all the programed contents. [Refer to “Factory reset, clearing all
memory” on page 14 for details.]
Once timer:
The timer will be canceled.
2
Perform “Setting the clock” from step 1 onwards.
Daily timer:
Timer and sleep operation (Remote
control only)
The timer operates at the same time every day. It will continue
until the daily timer setting is canceled. Cancel the daily timer
when it is not in use.
Once timer:
Notes:
ꢀ
Once timer play works for one time only at a preset time.
(“ ” indicator).
When performing timer playback using another unit
connected to the USB terminal or AUDIO IN jack, select
“USB” or “AUDIO IN” or “LINE IN” in step 5.
This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not turn on
or off.To stop the timer playback, follow step “Canceling the
timer setting” of this page.
Daily timer:
ꢀ
Daily timer play works at the same preset time every day that we
set. For example, set the timer as a wake-up call every morning.
(“DAILY” indicator).
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio program, and
use the daily timer to wake up.
Checking the timer setting:
1
2
3
Turn the power on and press and hold down the CLOCK/
TIMER button.
Within 10 seconds, press the
“Once” or “Daily”, and press the ENTER button.
or
button to select
1 minute or more
Within 10 seconds, press the or button to select
“Timer Call”, and press the ENTER button.
Once timer
Daily timer
Start
Start
Stop
Stop
Canceling the timer setting:
1
2
3
Turn the power on and press and hold down the CLOCK/
TIMER button.
ꢁ Timer playback
Within 10 seconds, press the
or
button to select
Before setting timer:
“Once” or “Daily”, and press the ENTER button.
ꢀ
Check that the clock is set to the correct time (refer to
page 11-12). If it is not set, you cannot use the timer
function.
Within 10 seconds, press the
or
button to select
“Timer Off”, and press the ENTER button. Timer will be
canceled (the setting will not be canceled).
ꢀ
For timer playback: Plug in USB or load discs or dock iPod
to be played.
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To reuse
the same setting, perform the following operations.
1
2
3
4
Turn the power on and press and hold down the CLOCK/
TIMER button.
1
2
3
Press the ON/STAND-BY button to turn the power on.
Press and hold the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
“Once” or “Daily”, and press the ENTER button.
Within 10 seconds, press the
“Once” or “Daily”, and press the ENTER button.
Within 10 seconds, press the or button to select
“Timer Set”, and press the ENTER button.
or
button to select
Within 10 seconds, press the or button to select
“Timer On” , and press the ENTER button.
4
5
Press the ON/STAND-BY button to enter the power stand-
by mode.
To select the timer playback source (CD, TUNER, USB, iPod,
AUDIO IN, LINE IN), press the
ENTER button.
or
button. Press the
When you select the tuner, select a station by pressing the
or
button, and then press the ENTER button. If a station
has not been programed, “No Preset” will be displayed and
timer setting will be canceled.
E-12
XL-HF201P_HF301P_US.indd 12
3/7/2012 10:35:26 AM
Timer and sleep operation
(Remote control only) (continued)
Enhancing your system
The connection cord is not included. Purchase a commercially
available cord as shown below.
ꢁ Sleep operation
The radio, compact disc, iPod, USB, Audio In and Line In
can all be turned off automatically.
1
2
3
Play back the desired sound source.
Press the SLEEP button.
Within 5 seconds, press the Numeric button to set the
time. (1 minute ~ 99 minutes)
4
5
“SLEEP” will appear.
The unit will enter the power stand-by mode
automatically after the preset time has elapsed. The
volume will be turned down 1 minute before the sleep
operation finishes.
Portable audio
player, etc.
To confirm the remaining sleep time:
While “SLEEP” is indicated, press the SLEEP button.
1
To cancel the sleep operation:
Audio cable (not supplied)
Press the ON/STAND-BY button while “SLEEP” is
indicated. To cancel the sleep operation without setting
the unit to the stand-by mode, proceed as follows.
ꢁ Listening to the playback sounds of
1
2
While “SLEEP” is indicated, press the SLEEP button.
Within 5 seconds, press the “0” button twice until
“SLEEP 00” appears.
portable audio player, etc.
1
Use a connection cord to connect the portable audio
player etc. to the AUDIO IN jack. When using video
equipment, connect the audio output to this unit and
the video output to a television.
ꢁ To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asleep listening to the radio and
wake up to CD in the next morning.
1
2
2
3
Press the ON/STAND-BY button to turn the power on.
Press the AUDIO/LINE (INPUT) button on the remote
control or FUNCTION button repeatedly on main unit
to select AUDIO IN function.
Set the sleep time (see above, steps 1 - 5).
While the sleep timer is set, set the timer playback
(steps 2 - 9, page 12).
4
Play the connected equipment. If volume level of the
connected device is too high, sound distortion may
occur. Should this happen, lower the volume of the
connected device. If volume level is too low, increase
the volume of the connected device.
Timer playback setting
Sleep timer setting
1-99 minutes
End time
Desired time
Timer playback start
time
Sleep operation will
automatically stop
Note:
To prevent noise interference, place the unit away from the
television.
ꢁ Headphones
ꢀ
Do not turn the volume on to full at switch on and listen
to music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
ꢀ
ꢀ
Before plugging in or unplugging the headphone,
reduce the volume.
Be sure your headphone has a 3.5 mm (1/8") diameter
plug and impedance between 16 and 50 ohms. The
recommended impedance is 32 ohms.
ꢀ
Plugging in the headphone disconnects the speakers
automatically. Adjust the volume using the VOLUME
control.
E-13
XL-HF201P_HF301P_US.indd 13
3/7/2012 10:35:26 AM
ꢁ iPod, iPhone or iPad
Troubleshooting chart
Many potential problems can be resolved by the owner without calling a
Symptom
Possible cause
service technician.
ꢀ
No sound is produced.
No image appears on
the TV/monitor.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
The iPod, iPhone or iPad is not
playing.
The iPod, iPhone or iPad is not
properly connected to the unit.
Is the AC power cord of the unit
plugged in?
The video cable is not properly
connected.
The TV/monitor’s input selection is not
properly set.
If something is wrong with this product, check the following before calling your
authorized SHARP dealer or service center.
ꢁ General
Symptom
Possible cause
ꢀ
ꢀ
The clock is not set to
the correct time.
ꢀ
Did a power failure occur? Reset the
clock. (Refer page 11)
When a button is
pressed, the unit does
not respond.
ꢀ
ꢀ
Set the unit to the power stand-by
mode and then turn it back on.
If the unit still malfunctions, reset it.
(Refer page 14)
The iPod TV out feature has not been
set to output video.
USB terminal do not support video.
ꢀ
ꢀ
ꢀ
No sound is heard.
ꢀ
ꢀ
ꢀ
Is the volume level set to “Min”?
Are the headphones connected?
Are the speaker wires disconnected?
ꢀ
ꢀ
iPod, iPhone or iPad will
not charge.
The iPod, iPhone or iPad is not making
full contact with the connector.
ꢀ
ꢀ
Using iPod (3rd generation).
The iPod or iPhone is not supported.
Refer to page 5 for compatible models.
ꢁ CD player
Symptom
Possible cause
“This accessory is
not made to work
with iPhone” or “This
accessory is not
supported by iPhone”
appears on iPhone
screen.
ꢀ
ꢀ
The iPhone battery is low. Please
charge the iPhone.
iPhone is not properly docked.
ꢀ
ꢀ
Playback does not start.
Playback stops in
the middle or is not
performed properly.
ꢀ
ꢀ
ꢀ
Is the disc loaded upside down?
Does the disc satisfy the standards?
Is the disc distorted or scratched?
ꢀ
Playback sounds are
skipped, or stopped in
the middle of a track.
ꢀ
Is the unit located near excessive
vibrations?
Is the disc very dirty?
Has condensation formed inside
the unit?
ꢀ
ꢀ
ꢁ Condensation
Sudden temperature changes, storage or operation in an extremely humid
environment may cause condensation inside the cabinet (CD pickup, etc.) or
on the transmitter on the remote control. Condensation can cause the unit to
malfunction. If this happens, leave the power on with no disc in the unit until
normal playback is possible (about 1 hour). Wipe off any condensation on the
transmitter with a soft cloth before operating the unit.
ꢁ Remote control
Symptom
Possible cause
ꢀ
The remote control
does not operate.
ꢀ
Is the AC power cord of the unit
plugged in?
ꢁ If problem occurs
ꢀ
ꢀ
ꢀ
ꢀ
Is the battery polarity correct?
Are the battery dead?
Is the distance or angle incorrect?
Does the remote control sensor
receive strong light?
When this product is subjected to strong outdoor interference (mechanical
shock, excessive static electricity, abnormal supply voltage due to lightning,
etc.) or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1
Set the unit to the stand-by mode and turn the power on again.
ꢁ Tuner
2
If the unit is not restored in the previous operation, unplug and plug in the
unit again, and then turn the power on.
Symptom
Possible cause
ꢀ
The radio makes
unusual noises
continuously.
ꢀ
ꢀ
Is the unit placed near the TV or
computer?
Is the FM antenna or AM loop antenna
placed properly? Move the antenna
away from the AC power cord if it is
located nearby.
Note:
If neither operation above restores the unit, clear all the memory by resetting
it.
ꢁ Factory reset, clearing all memory
1
2
Press the ON/STAND-BY button to enter the power stand-by mode.
While pressing down the OPEN/CLOSE button, press the ON/STAND-
BY button until “Clear All” appears.
ꢁ USB
Symptom
Possible cause
ꢀ
Device cannot be
detected.
ꢀ
ꢀ
ꢀ
ꢀ
Is there any MP3/WMA file available?
Is the device properly connected?
Is it an MTP device?
Caution:
This operation will erase all data stored in memory including clock, timer
settings, and tuner preset.
Does the device contain AAC file only?
ꢀ
Playback does not start.
ꢀ
ꢀ
Is it a copyright protected WMA file?
Is it a false MP3 file?
ꢁ Before transporting the unit
ꢀ
ꢀ
Wrong time display.
Wrong file name
display.
ꢀ
Is Variable Bitrate file being played
back?
Is the File Name written in Chinese or
Japanese characters?
Remove the iPod, iPhone, iPad, USB memory device and disc from the unit.
Then, set the unit to the power stand-by mode. Carrying the unit with iPod,
iPhone, iPad or USB memory device left docked or discs left inside might
damage the unit.
ꢀ
E-14
XL-HF201P_HF301P_US.indd 14
3/7/2012 10:35:27 AM
ꢁ CD player
Troubleshooting chart (continued)
Type
ꢁ Care of compact discs
Single disc multi-play compact disc player
Signal readout
Non-contact, 3-beam
Compact discs are fairly resistant to damage, however mistracking can occur
due to an accumulation of dirt on the disc surface. Follow the guidelines below
for maximum enjoyment from your CD collection and player.
semiconductor laser pickup
D/A converter
Multi bit D/A converter
20 - 20,000 Hz
ꢀ
ꢀ
ꢀ
Do not write on either side of the disc, particularly the non-label side from
which signals are read. Do not mark this surface.
Frequency response
Dynamic range
90 dB (1 kHz)
Keep your discs away from direct sunlight, heat, and excessive
moisture.
ꢁ USB (MP3 / WMA)
Always hold the CDs by the edges. Fingerprints, dirt, or water on the
CDs can cause noise or mistracking. If a CD is dirty or does not play
properly, clean it with a soft, dry cloth, wiping straight out from the center,
along the radius.
USB host interface
ꢀ
ꢀ
Complies with USB 1.1 (Full
Speed)/2.0 Mass Storage Class.
Support Bulk only and CBI protocol.
Maintenance
Support file
Bitrate support
Other
ꢀ
ꢀ
MPEG 1 Layer 3
WMA (Non DRM)
ꢁ Cleaning the cabinet
ꢀ
ꢀ
MP3 (32 ~ 320 kbps)
WMA (64 ~ 160 kbps)
Periodically wipe the cabinet with a soft cloth and a diluted soap solution,
then with a dry cloth.
ꢀ
ꢀ
ꢀ
Maximum total number of MP3/WMA
files is 65025.
Maximum total number of folders is
999 INCLUSIVE of root directory.
The ID3TAG information supported
are TITLE, ARTIST and ALBUM
only.
Supports ID3TAG version
version 2.
Caution:
ꢀ
Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It may
damage the cabinet.
ꢀ
Do not apply oil to the inside of the unit. It may cause malfunctions.
Specifications
ꢀ
ꢀ
1
and
As part of our policy of continuous improvement, SHARP reserves the right
to make design and specification changes for product improvement without
prior notice. The performance specification figures indicated are nominal
values of production units. There may be some deviations from these values
in individual units.
File system support
Support USB devices with Microsoft
Windows/DOS/FAT 12/FAT 16/ FAT
32.
ꢀ
2 kbyte block length for sector.
ꢁ General
ꢁ Tuner
Power source
AC 120 V ~ 60 Hz
40 W
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1,710 kHz
Power consumption
Dimensions
Width: 8 - 1/2” (215 mm)
Height: 3 - 4/5” (96 mm)
Depth: 13 - 1/5” (335 mm)
Preset
40 (FM and AM station)
ꢁ Speaker
Weight
5.7 lbs. (2.6 kg)
Type
2-way type speaker system
1” (2.5 cm) Dome-Tweeter
ꢁ Amplifier
4-3/4” (12 cm) Woofer (XL-HF201P)
5-1/8” (13 cm) Woofer (XL-HF301P)
Output power
RMS: Total 100 watt (50 W per channel
into 4 ohms at 1 kHz, 10% Total
harmonic distortion.)
FTC: 37.5 watt minimum RMS per
channel into 4 ohms from 100 Hz
to 20 kHz, 10% Total harmonic
distortion.
Maximum input power
Rated input power
Impedance
100 W
50 W
4 ohms
XL-HF201P
Dimensions
Output terminals
Input terminals
Speakers: 4 ohms
20Hz - 20kHz
Subwoofer Pre-out (audio signal):
200 mV/10 k ohms at 70 Hz
Video output: 1 Vp-p
Headphones: 16 ohms (recommended:
32 ohms)
Width: 5 - 13/16” (148 mm)
Height: 10-5/16” (262 mm)
Depth: 8” (203.5 mm)
Weight
5.4 lbs. (2.5 kg)/each
XL-HF301P
Dimensions
Audio In (audio signal):
500 mV/47 k ohms
Line in (Analog input):
500 mV/47 k ohms
Width: 6 - 5/16” (160 mm)
Height: 11-1/16” (280 mm)
Depth: 11 - 3/8” (289 mm)
Weight
9.3 lbs. (4.2 kg)/each
E-15
XL-HF201P_HF301P_US.indd 15
3/7/2012 10:35:27 AM
|