• User Manual •
SC3123
Caller ID Phone
SC3123 User Guide
TABLE OF CONTENT
PRODUCT OVERVIEW.....................................................................................3
1. INSTALLING OR REPLACING THE BATTERY .........................................................4
2. SWITCH OPERATION...................................................................................4
IDD LOCK switch.......................................................................................4
3. SOFTWARE SETTING ..................................................................................4
4. FUNCTION KEY OPERATION ..........................................................................6
UP and DOWN key.....................................................................................6
OUT key ................................................................................................6
DEL key .................................................................................................6
PAUSE key ..............................................................................................6
IP key ...................................................................................................6
FLASH (600ms) / RING key...........................................................................6
AUTO-RD REDIAL/BACK key..........................................................................6
HF (HANDSFREE) key..................................................................................6
5. ADDITIONAL NOTES ...................................................................................7
INCOMING CALL LCD INDICATOR.....................................................................7
LCD BACKLIGHT FUNCTION ..........................................................................7
TROUBLESHOOTING GUIDE..............................................................................7
DECLARATION OF CONFORMITY ........................................................................8
2
SC3123 User Guide
PRODUCT OVERVIEW
14
15
16
1
2
3
4
5
13
6
12
11109 8 7
Description:
1. LCD Display
2. SET key
11. UP key
12. OUT key
3. IP key
13. Handset Cord jack
14. LINE OUT (TEL) jack
4. FLASH/RING key
5. AUTO-RD REDIAL/BACK key 15. LINE IN (TEL) jack
6. HF (HANDSFREE) key
7. 0-9/#/* key
8. PAUSE key
16. LOCK switch
9. DOWN key
10. DEL key
3
SC3123 User Guide
1. INSTALLING OR REPLACING THE BATTERY
Install 3 Alkaline AA batteries into the battery compartment and re-fit the cover before use.
IMPORTANT—before removing the battery compartment cover, ensure the base unit
is disconnected from the telephone line.
Connection and conditions for use
You can connect your SC3123, to public networks in the United Kingdom or to an
approved PBX using DTMF signaling. Each item of telephone equipment (phones, fax
machines, etc.) has a ringer equivalence numbers (REN). The RENs of all
equipment connected to an exchange line must not add up to more than 4
otherwise, one or more phones may not ring and/or answer calls correctly.
SC3123 has a REN of 1, and most other telephones have a REN of 1 unless marked
otherwise.
2. SWITCH OPERATION
IDD LOCK switch
Use the keys provided in the package. The telephone allows all outgoing number if the key is
on red point. It cannot dial outgoing number starting with digit 0 when the key is on green
point.
3. SOFTWARE SETTING
Press the SET key to enter menu setting. The LCD panel will display SET 1 DATE, press the
UP/DOWN key to select the different options. Press the SET key again to confirm. Use the
UP/DOWN key to select the mode you need. After completing the setting, press the SET key
to go to next item. To exit menu, press the DEL key.
By pressing the SET key in the ‘on-hook’ mode, you can select the following:
SET ITEM
OPERATIONS
DATE/TIME
LCD displays SET 1 DATE, press the SET key to enter this mode. The
4
SC3123 User Guide
year value would flash, use the UP/DOWN key to select value. Press the
SET key to enter into next item.
AREA CODE
LCD display SET 2 CODE, press the SET key to confirm. LCD will display
CODE, press the SET key to enter this mode. Use the UP/DOWN key to
select value. Press the SET key to enter into next item.
Area Code can be used to filter the number for incoming calls. E.g.
Area code = 75 when there’s incoming call with 75 6554556, it will be
displayed as 655 4556 only.
LONG CODE
LCD display SET 3 LCODE, press the SET key to enter this mode. LCD
will displays LCODE, use the UP/DOWN key to select value. Press the
SET key to enter into next item.
To activate this feature, while checking incoming calls using UP key,
press REDIAL key twice to add the LONG DIST ACCESS code in front of
the number.
FLASH TIME
AUTO-IP
LCD display SET 4 FLASH, press the SET key to enter this mode. Use
the UP/DOWN key to select value. Press the SET key to enter into next
item.
LCD display SET 5 IP, press the SET key to enter this mode. LCD will
display AUTO IP OFF and OFF will flashes, use the UP/DOWN key to
select value. When LCD displays AUTO IP ON, press SET key. The LCD
will display INPUT CODE for you to enter the IP numbers. Use the DEL
key to correct any wrong input. After entering all IP number, press the
SET key to enter into next item. The outgoing call will automatically
use IP mode.
Auto IP allows you to replace a sequence of number with single 0. E.g.
Setting 1455 as Auto IP, therefore when you need to dial 1455, just put
0 in front (pre-dial mode), 0 2334565 will be dialed as 1455 2334565.
P/T MODE
ALARM
LCD display SET 6 P-T, press the SET key to enter this mode. LCD will
display TONE. Use the UP/DOWN key to change it into PULSE. Press
SET key to enter into next item.
LCD display SET 7 ALARM, press the SET key to enter this mode. LCD
will display ALARM OFF, which will turn the alarm off. Use the
UP/DOWN key to select ON or OFF.
This feature is to ensure other telephone is unable to share the same
line as your telephone. If another telephone is sharing the same line,
there will be constant noise when it is off hook.
5
SC3123 User Guide
4. FUNCTION KEY OPERATION
UP and DOWN key
In any mode, press the UP/DOWN key to check all the incoming numbers. If there is no
incoming call, LCD will display END. The unit can receive up to 16-digit number.
OUT key
In any mode, check outgoing numbers by pressing the OUT key. Use the UP/DOWN key to
select the outgoing number. Press the REDIAL key to dial the selected number.
DEL key
When checking incoming and outgoing call in any mode, press the DEL key to delete the
number you are checking. Press the DEL key for 4 sec to delete all incoming or outgoing call
numbers. When you pre-dial, press the DEL key to delete one digit at a time. When you enter
the IP number or password, use the DEL key to delete error digit.
PAUSE key
To insert a 3.6 second of pause while dialing, press PAUSE key and it will display P on the LCD
panel.
IP key
- When auto IP function is off:
In the ‘on-hook’ mode, pre-dial the phone number followed by the IP key. The unit will be
on-hook automatically and dial the number with the IP number. (Note: The IP function cannot
be used when the lock is set to lock “0”.)
- When auto IP function is on:
In the ‘on-hook’ mode, pre-dial the phone number followed by the REDIAL/BACK key. The
unit will off-hook automatically and dial the number with IP mode if the first digit number is
“0”.
FLASH (600ms) / RING key
In the ‘on-hook’ mode, press the FLASH/RING key. The LCD will display TONE 1-4 for four
selectable ringing tones. Select the preferred ringing tone by pressing the FLASH/RING key.
When LCD panel displays TONE OFF, it means the ringing tone is turned off.
For FLASH function:
In the on-hook mode, press this key to auto-hang up for 600ms, after that you can press
REDIAL key or dial out another number.
AUTO-RD REDIAL/BACK key
In the ‘on-hook’ mode, press this key to redial the last called number.
HF (HANDSFREE) key
While on-hook, press the HF key to go into handsfree mode. You can talk through the
6
SC3123 User Guide
microphone and listen from the speakerphone without lifting the handset. While off-hook,
press the HF key and put down the handset to go into handsfree mode.
5. ADDITIONAL NOTES
INCOMING CALL LCD INDICATOR
When there is incoming call, the unit will be automatically display the caller number, date
and time, and also display its serial number. If the incoming call is in private mode, it will
display “__p__”; it will display “__0__” if exchange cannot determine the number; it will
display “—E—“ if the call signal contains error.
LCD BACKLIGHT FUNCTION
When there is incoming call or handset is off-hook, the LCD backlight will lit up. It will be on
for about 6 seconds before going off. Without batteries, LCD backlight will not lit up at all.
TROUBLESHOOTING GUIDE
(Q) I do not hear any dial tone from the handset.
(A) Ensure the handset cord is connected correctly from the handset to the handset cord jack
at the base. Ensure you have plug in the telephone cable from the telephone to the wall
socket correctly. If the problem persists, please check with your local dealer.
(Q) I could not see the caller’s number on the LCD when there is incoming call.
(A) Ensure that you have subscribed Caller ID service from your local telecom provider.
(Q) There is no LCD Display / Backlight after I have connected the telephone line. I can
call out normally.
(A) Ensure that you have inserted the batteries on the battery compartment. If there is still
no display, change the batteries and ensure it is not empty. If the problem persists, please
check with your local dealer.
7
SC3123 User Guide
DECLARATION OF CONFORMITY
The telephone complies with the essential protective requirements and objectives of:
•
•
•
EC R& TTE Directive 1999/5/EC
EC Low Voltage Directive 73/23/EEC
EC EMC Directive 89/336/EEC
And conforms to the following relevant harmonized standards:
•
•
EMC: EN55022, EN55024
Safety: EN 60950
Created on 28th October 2005. SC3123 Caller ID Phone.
Please visit us at www.shirocorp.com.
8
|