CORDLESS RADAR/LASER DETECTOR
S O L O
Check Quick
Reference Guide
inside cover !
®
pwr/vol
dim
city
mute
O W N E R ' S M A N U A L
M O D E L R D - 5 1 1 0
®
T A B L E O F C O N T E N T S
Installing SOLO's Batteries..........................................................1
Battery Life Indication ..............................................................1,7
Low Battery Warning ...............................................................2,7
AutoOff.......................................................................................2
Mounting SOLO..........................................................................3
Controls and Indicators
Power On .............................................................................4
Volume.......................................................................................4
Mute...........................................................................................5
AutoMute....................................................................................5
Highway/City Modes.............................................................5
Dim Modes...........................................................................5
Audible Alerts .......................................................................6
Power On Indicator...............................................................6
City Indicator ........................................................................6
Band Indicators.....................................................................6
Signal Meter..........................................................................6
Safety Signals ........................................................................6
Mounting Adjustment Button ................................................7
Radar Antenna ......................................................................7
Laser Lenses..........................................................................7
Power Jack............................................................................7
Programmable Options...............................................................8
Tutorial Mode ...........................................................................10
Specifications...............................................................................11
Interpreting Alerts ......................................................................12
How Radar Works .....................................................................14
How Laser Works......................................................................14
How Safety Signals Work...........................................................15
Troubleshooting..........................................................................16
Service........................................................................................18
Warranty....................................................................................19
Optional Accessories ................................................................20
I M P O R T A N T B A T T E R Y I N F O R M A T I O N
SOLO is designed to operate on two standard AA alkaline batteries. AA
lithium batteries and AA alkaline rechargeable batteries may also be used,
however the resulting battery life will vary. We do not recommend using
NiCad rechargeable batteries.
Installing SOLO’s Batteries
1
2
Make sure SOLO is turned off.
Turn SOLO upside down. Depress the
battery door and sliding in the direction
of the arrow, remove door from the
battery compartment.
3
4
Remove any old batteries (both batteries MUST
be replaced at the same time).
Observing the polarity indication inside the battery
compartment, insert two fresh AA alkaline batteries.
Replace battery door.
5
6
Turn SOLO on to verify correct battery installation.
NOTE: Please dispose of used batteries properly in accordance with
federal, state and local requirements.
Battery Life
SOLO’s efficient design provides the typical driver with about 50 hours of
battery life from two AA alkaline batteries. Battery life is affected by many
variables, including the brand and age of the batteries, the ambient
temperature, how many and what type of alerts SOLO receives (weak
signals use less battery power than full alerts). In addition, the way you
use SOLO’s alert system will affect the battery life (low audio volume uses
less power than full volume, and Dim mode uses less power than normal
mode). The approximate battery life figures we quote are based on
laboratory testing, using fresh batteries. Your specific conditions and
usage may result in longer or shorter battery life.
Battery Life Indication
As discussed in the Signal Meter section on page 7, remaining battery life
is displayed on SOLO's Signal Meter both at power up and power down.
NOTE: Extreme temperature conditions can cause SOLO's Battery Life
Indication to be inaccurate until SOLO's temperature returns to normal.
REGARDLESS OF YOUR ACTUAL BATTERY LIFE, SOLO’S PERFOR-
MANCE WILL NOT DEGRADE AS BATTERY VOLTAGE BEGINS TO
DROP. SOLO IS DESIGNED TO SHUT DOWN BEFORE PERFORMANCE
IS IMPAIRED BY WEAK BATTERIES.
For best battery performance:
•
•
Purchase fresh, name brand batteries.
Store batteries in their original packaging before use to prevent the
IMPO RTANT BATTERY INFO RMATIO N
1
I M P O R T A N T B A T T E R Y I N F O R M A T I O N
battery contacts from shorting against metal objects.
•
•
Never mix old and new batteries in SOLO or any device.
Since batteries last longest if used at room temperature, use SOLO at
room temperature whenever possible.
•
Turn off SOLO when not in use.
AutoOff
SOLO has a special automatic shut-off feature to conserve battery life in
case you forget to turn SOLO off. (Please refer to page 4 for an explana-
tion of the AutoOff circuit.)
NOTE: The presence of even a weak signal can cause SOLO to remain
on. Turn SOLO off whenever you leave your car as the AutoOff circuit
turns SOLO off after 45 minutes ONLY if no signals are detected. A
passing police car or a nearby motion sensor could be enough to keep
SOLO on, thereby draining your batteries.
NOTE: We recommend using only standard AA alkaline batteries for the
most consistent battery life. While AA lithium batteries and AA alkaline
rechargeable batteries may also be used, the resulting battery life will
vary. We do NOT recommend NiCad rechargeable batteries.
WARNING
Do not leave SOLO in direct sunlight in a parked vehicle, as it may
exceed the battery’s temperature limit and damage the batteries and the
detector. This damage is not covered by SOLO’s warranty.
Low Battery Warning
When SOLO's batteries have only approximately six hours of battery life
remaining, SOLO will sound two “bleeps” and flash the entire Signal
Strength Meter every five minutes. SOLO’s batteries should be replaced at
this time since performance begins to decline once the batteries are
within the warning range. The amount of battery life remaining depends,
to a large extent, on how many alerts you receive and how your SOLO is
being used. If you are unable to replace SOLO’s batteries at the start of
the Low Battery warning, consider lowering your SOLO’s audio volume
and utilizing the AutoMute, Mute and Dim features to prolong battery life.
Optional Power Cord
SOLO’s power jack allows you to power SOLO using an optional Power
Cord. SOLO is designed for 3V operation and its unique circuitry will not
accommodate a standard 12V power cord. Using any cord other than the
Power Cord/Converter Set designed specifically for SOLO may cause
damage not covered by warranty. To order a SOLO Power Cord/Converter,
call 1-800-433-3487 toll-free.
WARNING
SOLO should never be directly wired to any power source, particularly a
12V automotive source. Use ONLY with SOLO's 3V power converter.
2
IMPO RTANT BATTERY INFO RMATIO N
M O U N T I N G S O L O
WARNING
ESCORT CANNOT ANTICIPATE THE MANY WAYS SOLO CAN BE
MOUNTED. IT IS IMPORTANT THAT YOU MOUNT SOLO WHERE IT
WILL NOT IMPAIR YOUR VIEW NOR PRESENT A HAZARD IN CASE OF
AN ACCIDENT.
For optimum detection performance, we recommend the following:
Using the Windshield Mount, mount SOLO relatively level and high
enough on your front windshield to provide a clear view of the road
from the front and rear.
•
Mount SOLO away from windshield wipers, other solid objects and
heavily tinted areas that might obstruct the radar antenna or laser lens.
Keep the laser lens at the rear of SOLO clean. To clean, apply a small
amount of eyeglass cleaning solution with a soft cloth.
•
•
Mounting SOLO to Your Windshield:
SOLO’s patented EasyMount windshield bracket is designed for
unobtrusive and hassle-free mounting.
1
Insert each suction cup into large end of bracket hole and rotate cup
outward, locking into place.
2
Depress the adjustment button on the top of SOLO and slide
EasyMount bracket into the slot until mount is locked into the position
which best fits the angle of your windshield. (For extremely horizontal
or extremely sloped windshields, the EasyMount bracket can be bent.)
Mount SOLO on your windshield. Use the adjustment button to slide
SOLO forward or backward to a horizontal position. WHEN
ADJUSTED PROPERLY AND TO MINIMIZE BOUNCING, THE BACK
TOP EDGE OF SOLO SHOULD REST SOLIDLY AGAINST YOUR
WINDSHIELD.
3
To ensure that the suction
cups adhere to the windshield
firmly, be sure to keep both
your windshield and the
suction cups clean.
CAUTION!
Some windshields have an “anti-lacerative” coating. Use of suction cups
could permanently mar the coating. Consult your dealership or the
vehicle’s owner’s manual to determine if your windshield has this coating.
MO UNTING SOLO
3
C O N T R O L S A N D I N D I C A T O R S
11
10
12 13
2
3
4
11 5
1
®
pwr/vol
dim
city
mute
6 7 8
9
MEMORY RETENTION FOR PREFERRED SETTINGS
Keep the factory preset settings for Volume, Dim, AutoMute, City and
other programmable features or select your own with SOLO's on-board
computer. Your selected settings stay in SOLO's Memory even when it's
turned off or the batteries are changed. For more information on SOLO's
programmable options, the first in the industry, see page 8.
1 POWER AND VOLUME To turn SOLO on and off: briefly press the Power/
Volume Button. The Power-On indicator blinks to show SOLO is on
and there will be a five-second test alert followed by a two-second
display of remaining battery life on the Signal Meter. Battery life is also
displayed each time you turn SOLO off. (Battery status indication is
more thoroughly discussed in the Signal Meter section on page 7.) The
five-second test alert can be bypassed and blinking Power-On indicator
can be made continuous (see Programmable Options on page 8 for
more information).
To adjust audio volume: Press and hold the Power/Volume Button.
SOLO will cycle through the 10 volume levels and show the relative
audio level on the Signal Meter. To reverse the direction of the audio
level, briefly release and press again. Once the volume level has been
changed, a two second hold time will be engaged to allow you to
further modify volume without turning SOLO off. Once selected, the
volume setting will be retained in SOLO’s memory.
AUTOOFF SOLO has an automatic shut-off feature to conserve battery
life in case you forget to turn SOLO off. If SOLO does not detect any
signals for 45 minutes, it assumes that it is not in use and you have
forgotten to turn it off. SOLO will sound a declining “power-down”
alert and then turn itself off in five seconds. To keep SOLO from
turning off (such as when you are driving through a very remote area
where alerts are infrequent), press any of SOLO’s buttons. SOLO will
4
CO NTRO LS AND INDICATO RS
C O N T R O L S A N D I N D I C A T O R S
sound a “double-bing” confirming that it will remain on. (AutoOff can
be “permanently” deselected. See Programmable Options on page 8
for more information).
NOTE: Since the presence of even an extremely weak signal will keep
SOLO on, turn SOLO off whenever you leave your car to prevent the
batteries from being drained.
2
MUTE To mute the audio for a single specific signal: Briefly press the
Mute Button. After the signal has passed, SOLO will automatically reset
for the next alert. If a new signal is encountered during the signal you
have just muted, SOLO’s patented SmartMuteTM reverts to full audio to
ensure that you do not miss this new signal.
AUTOMUTE SOLO is shipped with AutoMute engaged. In AutoMute
mode, the audio for the first four audible tones or four seconds
(whichever is longer) in an alert situation will be emitted at your
selected volume level and all subsequent audible tones during the
same alert will be emitted at a lower volume level. After the signal has
passed, SOLO automatically resets to the volume level you have set.
(AutoMute can be deselected. See Programmable Options on page 8
for more information).
3 HIGHWAY/CITY MODE Each time you turn SOLO on, the last Highway/
City mode selected is the one which is automatically engaged. We
recommend driving in Highway mode most of the time for maximum
sensitivity. When driving in urban areas where annoying X-band
intrusion alarms and door openers are common, City Mode can be
engaged to lower X-band sensitivity and reduce X-band alerts. Full
sensitivity is maintained on all other bands. To select City Mode:
Briefly press the City Button. The City Indicator will blink and SOLO’s
X-band sensitivity level will be lowered to a level to suit most urban
driving environments. Three other City Mode levels are available for
more problematic urban environments (see Programmable Options on
page 8 for more information). Also, the City Indicator can be
programmed to not blink and light solid (see Programmable Options
on page 8 for more information). To return to Highway Sensitivity:
Briefly press the City Button again.
4
DIM MODES To adjust SOLO’s display: Briefly press the Dim Button.
With each press, SOLO will cycle through the four display settings as
follows: 1st press = Full Dark, 2nd press = Low, 3rd press = Medium,
4th press = High. SOLO is preset at our factory on High (Full Bright).
Your most recent selection is retained in SOLO’s memory until you
select a different brightness level as the default. (See Programmable
Options on page 8 for more information on how to store a display
default.)
Download from Www.Somanuals.com. All Manuals SeaArcNhD AINnDdICDAToOwRnS load.
CO NTRO LS
5
C O N T R O L S A N D I N D I C A T O R S
5
AUDIBLE ALERTS For Radar and Laser signals: SOLO uses a geiger-
counter-like sound to indicate the signal strength and type of radar or
laser signal being encountered. When you encounter radar or laser, a
distinct Audible Alert will sound and occur faster as the signal gets
stronger. When the signal is very strong, the Audible Alerts will blend
into a solid tone. This allows you to judge the distance from the signal
source without taking your eyes from the road. Each band has a
distinct tone for easy identification. X-band = beep tone, K-band =
raspy brap tone, Ka-band = double-bleep tone, Laser = chirp tone.
Please see page 12 for details on the typical behavior of various radar
and laser signals.
For Safety signals: Each type of safety signal has its own distinctive
brap tone. Emergency Vehicle = rapid braps, Railroad Crossing =
repetitive brap, Road Hazard = repetitive double brap. THE PRESENCE
OF ONE OF THESE SIGNALS INDICATES A DANGEROUS DRIVING
CONDITION. Be particularly alert and aware of what’s going on
around you. (For more information on SOLO’s SafetyPilotTM and the
use of Safety transmitters, please see page 15.)
6
7
8
POWER-ON INDICATOR When your SOLO is turned on, the Power-On
Indicator will illuminate.
CITY INDICATOR The City Indicator will light whenever City mode is
selected.
BAND INDICATORS When a radar or laser signal is detected, the
appropriate Band Indicator will light to show which type of signal is
being detected; “X” for X-band, “K” for K-band, “Ka” for Ka-band or
“L” for laser.
9
SIGNAL METER The Signal Meter consists of 5 red LEDs and provides the
following information.
Signal Strength: The more meter lights lit during a radar or laser
encounter, the stronger and closer the signal.
Type of Safety Signal: Safety Signals are displayed as shown below.
EMERGENCY VEHICLE
Signal Meter scans quickly from right to left.
ROAD HAZARD
All Signal Meter lights double-flash simultaneously.
RAILROAD
First two Signal Meter Lights alternate flashing with last two Signal Meter Lights.
6
CO NTRO LS AND INDICATO RS
C O N T R O L S A N D I N D I C A T O R S
Battery Life Indication: Remaining battery life is displayed on the Signal
Meter for 2 seconds both at power-up (after the five-second test alert)
and at power-down. NOTE: Extreme temperature conditions can cause
SOLO's Battery Life Indication to be inaccurate until SOLO's
temperature returns to normal.
5 LEDs lit = 80% of battery life remains
4 LEDs lit = 60% to 80% of battery remains
3 LEDs lit = 40% to 60% of battery life remains
2 LEDs lit = 20% to 40% of battery life remains
1 LED lit = less than 20% of battery life remains
Low Battery Warning: When approximately six hours of battery life
remains, SOLO will sound two short “bleeps” and flash the entire
Signal Meter every five minutes to indicate the batteries need
replacing. The amount of battery life remaining depends, to a large
extent, on how many alerts you receive and how SOLO is being used.
If you are unable to replace SOLO’s batteries at the start of the Low
Battery warning and do not have a SOLO Power Cord, lower SOLO’s
audio volume and utilize AutoMute or Mute and Dim to prolong
battery life.
10 RADAR ANTENNA The antenna detects incoming radar signals.
11 LASER LENSES Dual lenses provide 360 degree protection.
12 MOUNTING ADJUSTMENT BUTTON This button allows you to adjust the
mounting bracket to suit your driving environment. Please refer to
page 3 for a complete explanation on mounting.
13 POWER JACK Allows you the option of using a power cord in place of
the battery power source in order to provide back-up or alternative
power for your SOLO through your vehicle’s cigarette lighter.
(SOLO’s unique circuitry will not accommodate a standard 12V
power cord. Using any cord other than the Power Cord designed
specifically for SOLO may cause damage not covered by warranty. To
order a SOLO Power Cord, call 1-800-433-3487 toll-free.)
CO NTRO LS AND INDICATO RS
7
P R O G R A M M A B L E O P T I O N S
SOLO’s features are preset for optimum performance and battery life but
you may change some settings to better suit your specific needs. Once a
setting is stored into memory, it remains until you decide to reprogram it.
OPTION
WHEN TO USE
HOW TO SELECT
Disengage
AutoMute
If you prefer full audio Press and HOLD the Mute
volume for the duration button. A “bing” tone will
of alerts. NO TE: Any confirm your selection. To
single alert may still be re-engage AutoMute, press
muted by briefly pressing and hold the Mute button
the Mute button during again. A “double-bing”
that alert.
tone will confirm your
return to AutoMute.
If you find the power-on Press and HOLD the Mute
test alert bothersome. If button at the same time you
you wish to preserve a bit turn SOLO on to replace the
Bypass five-second
test alert
more battery life.
five-second sequence with
a one-second alert. Repeat
operation to re-engage the
full test alert.
Press and HOLD the Dim
button at the same time you
turn SOLO on. The Power-
On Indicator will light con-
tinuously while SOLO is
on. The City Indicator will
light continuously while
SOLO is in City mode.
Non-blinking
Power-On
Indicator and
City Indicator
If you find the blinking
Power-On and City Indi-
cators too bothersome.
WARNING:Selectingthis
option will reduce your
battery life.
If you drive in an remote
area where alerts are very
infrequent, this option
keeps SOLO from trying
to turn itself off due to
lack of signals.
Press and HOLD the Mute
and Dim buttons at the
same time when SOLO is
on. A “bing” tone confirms
your selection. Repeat to
Disengage
AutoOff
re-engage AutoO ff.
A
“double-bing” tone will
confirm your selection.
Select a default
Assures SOLO returns to Press and HOLD the Dim
brightness setting
your favorite brightness Button at the selected
for SOLO’s display settingeach time you turn brightnesslevel. A“double-
iton. (Ifno brightnesslevel bing” tone will confirm
isselected, SOLO willuse your selected default.
the last one selected.)
8
PRO GRAMMABLE OPTIO NS
P R O G R A M M A B L E O P T I O N S
OPTION
WHEN TO USE
HOW TO SELECT
Select an alternative If you drive in an urban Press and HOLD the City
X-band sensitivity area where non-police X- button. SOLO will cycle
level for City Mode band alerts from motion through the 4 available
sensors and intrusion City sensitivity levels and
alarms are prevalent, this display relative X-band
option allowsyou to select sensitivity on the Signal
an X-band sensitivitylevel Meter (as shown below).
below the standard City Release button at your
Mode setting.
preferred setting.
Signal Meter LEDS LIGHT UP IN THE PATTERNS INDICATED AS YOU ADJUST CITY LEVELS
▲
Level 4 Moderately reduced X-band sensitivity. Best suited to
suburban environments where intruding signals are
occasional.
Level 3 Significantlyreduced X-band sensitivity. SOLO'sdefault
setting and best suited to typical driving environments.
Level 2 Drastically reduced X-band sensitivity. For use in
downtown areas which are aggressively populated
with intruding signals.
Level 1 Zero X-band sensitivity. To be used ONLY in those
rare locations where X-band radar is not used.
Select alternate
audio tones
Allows you to select al- Press and HOLD the Dim
ternative audio tones and Citybuttonsatthe same
(owners of earlier ES- time you turn SOLO on.
CORT detectors will rec- Repeat operation to re-
ognize these tones as the select the factory default
more "classic" style used audio tones.
in the past).
Returning To SOLO's Factory Preset Settings
You may re-engage SOLO's factory preset settings at any time. To do so,
press and HOLD the Mute, City and Dim buttons at the same time as you
turn SOLO on.
PRO GRAMMABLE OPTIO NS
9
T U T O R I A L M O D E
SOLO is equipped with a Tutorial mode to demonstrate all of the alerts and
settings below in order to better familiarize you with them. To access the
tutorial mode, simultaneously press and hold the Mute and City buttons as
you turn SOLO on. SOLO will then demonstrate each of the following:
FEATURE
DEMONSTRATION
Laser Alert
Laserindicatorlightsassignalmeterramps
down. Laser audio sounds.
Ka-band Alert
K-band Alert
X-band Alert
Ka indicator lights as signal meter ramps
down. Ka audio sounds.
K indicator lights as signal meter ramps
down. K audio sounds.
X indicator lights as signal meter ramps
down. X audio sounds.
AutoMute
As SOLO simulates an X-band encounter,
AutoMute is demonstrated when audio
automatically reduces after first several
tones.
Emergency Vehicle Alert
Railroad Alert
Signal Meter scans swiftly right to left.
Emergency Vehicle audio sounds.
Two end Signal Meter positions alternate
flashing (like a railroad crossing sign).
Road Hazard Alert
Entire Signal Meter double-flashes. Road
Hazard audio sounds.
Cycling of four City settings
Shows how four available City settings
are indicated on the Signal Meter as city
level is selected.
Cycling of four Dim settings
Cycling of ten Volume settings
Shows how four available Dim/Dark set-
tings are indicated on the Signal Meter
as the display brightness level is selected.
Shows how ten available Volume set-
tings are indicated on the Signal Meter
as volume level is selected.
Low Battery Warning
AutoOff Warning
Signal Meter flashes as two short "bleep"
tones sound.
SOLO sounds a declining "power down"
alert and SOLO turns off.
10
TUTO RIAL MO DE
S P E C I F I C A T I O N S
RECEIVER TYPE
RADAR:
Double Conversion Superheterodyne Voltage
Controlled Oscillator (VCO)
LASER:
Quantum Limited Video Receiver
ANTENNA TYPE
RADAR & SAFETY: Self-Contained, Die-Cast Horn, Linear Polarization
(compatible with circular polarization)
LASER:
Infrared Photodiode with Fresnel Lens and
Refractive/Prismatic Element
DETECTOR TYPE
RADAR & SAFETY: Scanning Frequency Discriminator
Video Envelope
LASER:
OPERATING FREQUENCIES & WAVELENGTHS
X-band: 10.525 GHz (center)
K-band and Safety: 24.150 GHz (center)
Ka-band: 34.7 GHz (center)
Laser: 900 NanoMeters (center)
BANDWIDTHS
Radar and Safety:
X-band: 50 MHz
K-band and Safety: 200 MHz
Ka-band: 2.60 GHz
Laser:
33MHz
ALERT HOLD TIME 4 Seconds
DIMENSIONS
1.2 inches x 2.85 inches x 5.06 inches
OPERATING TEMPERATURE RANGE
With Alkaline Batteries: -18C to 55C (0F to 131F)
With Power Cord Only: -18C to 70C (0F to 158F)
STORAGE TEMPERATURE RANGE
With Alkaline Batteries: -40C to 55C (-40F to 131F)
With Power Cord Only: -40C to 85C (-40F to 185F)
POWER REQUIREMENT
Two Standard AA Batteries or Power Cord which converts 12V to 3V
SIGNAL PROCESSING
Digital Signal Processing (DSP)
Specifications are subject to change without notice.
SPECIFICATIO NS
11
I N T E R P R E T I N G A L E R T S
Although SOLO has a comprehensive warning system and this handbook
is as complete as we can make it, only experience will teach you what to
expect from your SOLO and how to interpret what it “tells” you. The radar
alerts you receive are affected by the type of radar being used, the type of
transmission (continuous or instant-on) and the location of the radar
source. The following examples will give you an introduction to
understanding SOLO’s warning system for radar, laser and safety alerts.
ALERT
EXPLANATION
SOLO begins to sound slowly, then You are approaching a continuous
the rate of alerts increase until a solid radar source aimed in your direction.
tone is achieved. The Signal Meter
ramps accordingly.
SOLO emits short alerts for a few An instant-on radar source is being
seconds and then falls silent only to used ahead of you and out of your
briefly alert and fall silent again.
view.
SOLO suddenly sounds a continuous An instant-on radar source or laser
tone for the appropriate band source is being used nearby. This
received. AllLEDs in the SignalMeter kind of alert requires immediate
are lit.
attention!
A brief laser alert.
Laserisbeingused in the area. Because
laser is inherently difficult to detect,
even a weak laser alert may indicate
a source very close by. Any laser alert
requires immediate attention!
SOLO receives weak signals. These A moving patrol car with continuous
signals may be a little stronger as you radar is overtaking you from behind.
pass large, roadside objects. The Because these signals are reflected
signals increase in frequency.
(reflections are increased by large
objects), they may or may not
eventuallymeltinto a solid pointeven
when the patrol car is directly behind
you.
SOLO alerts slowly for awhile and You are approaching a radar unit
then abruptly jumps to a strong alert. concealed by a hill or an obstructed
curve.
12
INTERPRETING ALERTS
I N T E R P R E T I N G A L E R T S
ALERT
EXPLANATION
SOLO alerts intermittently. Rate and Apatrol car is travelling in front of you
strength of alerts may be consistent or with a radar source aimed forward.
vary wildly.
Because signals are sometimes
reflected off of large objects and
sometimes not, the alerts may seem
inconsistent.
SOLO alerts intermittently. Rate and A patrol car is approaching from the
strength of signal increases with each otherdirection, “sampling”traffic with
alert.
instant-on radar. Such alerts should
be taken seriously.
SOLO gives an X-band alert
intermittently.
You are driving through an area
populated with radar motion sensors
(door openers, burglar alarms, etc.)
Since these transmitters are usually
contained inside buildings or aimed
toward OR away from you, they are
typically not as strong or lasting as a
real radar encounter.
CAUTION: Since the characteristics
of these alerts may be similar to some
of the preceding examples, overcon-
fidence in an unfamiliar area can be
dangerous. Likewise, if an alert in a
commonly travelled area is suddenly
stronger or on a different band than
usual, speed radar may be set up
nearby.
SOLO braps rapidly and the Signal A fast-travelling emergency vehicle is
Meter scans from right to left. in the vicinity.
SOLO sounds a repetitive “double- You are approaching a hazardous
brap” and the entire Signal Meter road condition such as an accident
flashes.
site or construction.
SOLO sounds a repetitive “brap” and You are approaching a dangerous
the two LEDs on each end of the railroad crossing.
Signal Meter alternate flashing.
INTERPRETING ALERTS
13
H O W R A D A R & L A S E R W O R K
HOW RADAR WORKS
Traffic radar, which consists of microwaves, travels in straight lines and is
easily reflected by objects such as cars, trucks, even guardrails and
overpasses. Radar works by directing its microwave beam down the road.
As your vehicle travels into range, the microwave beam bounces off your
car, and the radar antenna looks for the reflections. Using the Doppler
Principle, the radar equipment then calculates your speed by comparing
the frequency of the reflection of your car to the original frequency of the
beam sent out.
Traffic radar has limitations, the most significant of these being that it
typically can monitor only one target at a time. If there is more than one
vehicle within range, it is up to the radar operator to decide which target
is producing the strongest reflection. Since the strength of the reflection is
affected by both the size of the vehicle and its proximity to the antenna, it
is difficult for the radar operator to determine if the signal is from a sports
car nearby or a semi-truck several hundred feet behind.
Radar range also depends on the power of the radar equipment itself. The
strength of the radar unit’s beam diminishes with distance. The farther the
radar has to travel, the less energy it has for speed detection.
Because intrusion alarms and motion sensors often operate on the same
frequency as X-Band radar, your SOLO will occasionally receive non-
police radar signals. Since these X-Band transmitters are usually contained
inside of buildings or aimed toward the ground, they will generally
produce much weaker readings than will a true radar encounter. As you
become familiar with the sources of these pseudo alarms in your daily
driving, they will serve as confirmation that your SOLO’s radar detection
abilities are fully operational.
HOW LASER (LIDAR) WORKS
Laser speed detection is actually LIDAR (Light Detection And Ranging).
LIDAR guns project a beam of invisible infrared light. The signal is a series
of very short infrared light energy pulses which move in a straight line,
reflecting off your car and returning to the gun. LIDAR uses these light
pulses to measure the distance to a vehicle. Speed is then calculated by
measuring how quickly these pulses are reflected given the known speed
of light.
LIDAR (or laser) is a newer technology and is not as widespread as
conventional radar, therefore, you may not encounter laser on a daily
basis. And unlike radar detection, laser detection is not prone to “false”
14
HO W RADAR & LASER WO RKS
H O W S A F E T Y S I G N A L S W O R K
alarms. Because LIDAR transmits a much narrower beam than does radar,
it is much more accurate in its ability to distinguish between targets and is
also more difficult to detect. AS A RESULT, EVEN THE BRIEFEST AND
WEAKEST LASER ALERT SHOULD BE TAKEN SERIOUSLY.
There are limitations to LIDAR equipment. LIDAR is much more sensitive
to weather conditions than RADAR, and a LIDAR gun’s range will be
decreased by anything affecting visibility such as rain, fog, or smoke. A
LIDAR gun cannot operate through glass and it must be stationary in order
to get an accurate reading. Because LIDAR must have a clear line of sight
and is subject to cosine error (an inaccuracy which increases as the angle
between the gun and the vehicle increases) police typically use LIDAR
equipment parallel to the road or from an overpass. LIDAR can be used
day or night.
HOW SAFETY SIGNALS WORKS
FCC-approved Safety signal transmitters emit microwave radar signals to
indicate the presence of a safety-related concern. Depending on the
frequency location of these signals as set on the transmitter, the outgoing
signal can indicate whether the transmitter is located in a speeding
emergency vehicle, at a road hazard location or at a railroad crossing.
These dual-frequency microwave signals are located in the K-bandwidth
and, as a result, any radar detector which detects K-Band radar will detect
these Safety signals as standard K-Band radar alerts. However, unlike
standard radar detectors, your SOLO is designed to distinguish between a
standard K-Band alert and a Safety signal alert. It will also demonstrate
which type of Safety signal is being received: Emergency Vehicle, Road
Hazard or Railroad.
Since Safety technology is relatively new and the number of transmitters
in operation is not yet widespread, you may not receive Safety signals on
a daily basis and should not be surprised to encounter some emergency
vehicles, road hazards and railroad crossings that are unequipped with
these transmitters and, therefore, fail to provide a signal. As Safety
transmitters become more prevalent (the number of operating transmitters
is growing every day), these Safety signals will become more common.
IF YOU EVER HAVE QUESTIONS ABOUT THE PERFORMANCE OR OPERATION OF YOUR SOLO, PLEASE
CALL TOLL-FREE 1-800-543-1608.
HO W SAFETY SIGNALS WO RK 15
T R O U B L E S H O O T I N G
PROBLEM
SOLUTION
SOLO will not turn on when Power
Button is pressed.
Check to make sure batteries are
not missing.
•
Batteries may need replacing.
Batteries may be installed
improperly.
•
•
SOLO beeps briefly at the same
location every day, but no radar
source is in sight.
SOLO is functioning properly.
An X-band motion sensor or
intrusion alarm is located within
range of your route. With time,
you will learn predictable
•
patterns of these signals.
Make sure that SOLO’s radar
antenna is not blocked by
windshield wipers or solid
objects or that the laser lens is
not behind tinted areas.
•
•
SOLO does not seem sensitive to
radar or laser.
Determine if your vehicle has an
InstaclearTM, ElectriClear® or
solar energy reflective
windshield which may deflect
radar or laser signals.
SOLO may be in City Mode.
•
•
•
SOLO did not alert when a police
car was in view.
VASCAR, a stopwatch method of
speed detection, may be in use.
Officer may not have radar or
laser unit turned on.
SOLO did not provide a Safety
signal at a hazardous road
condition, railroad crossing or
while within range of an emergency
vehicle.
Safety transmitters may not be
commonly used in your area.
•
SOLO alerts for Ka radar when no
radar source is in sight.
Falsing on this band is virtually
non-existant. Take all Ka alerts
seriously. There may be an instant-
on radar source out of sight. Only
a smallnumberofproductsoperate
in the Ka band which may cause
an occasional false alert.
•
16
TRO UBLESHO O TING
T R O U B L E S H O O T I N G
PROBLEM
SOLUTION
Signal Meter registers but no
audible alert sounds.
SOLO is probably in City mode
where X-band alerts are
purposefully reduced.
•
SOLO’s display is not working.
Briefly press the Dim button to
deactivate Dark Mode.
•
•
•
SOLO’s audible alerts are less loud
after the first few alerts.
SOLO is in AutoMute Mode. See
page 5 for details.
All Signal Meter lights flash
occasionally and SOLO "bleeps"
twice each time.
SOLO’s batteries are low.
Replace batteries as described on
page 1.
SOLO bounces or sags on
windshield.
SOLO is not making contact with
the windshield to provide stability.
While holding down SOLO’s
EasyMount button, slide SOLO
further back toward the wind-
shield so that the back top edge
makes firm contact. See page 3
for details.
•
Suction cups may be worn and
need replacing. To order
replacement suction cups, call
1-800-433-3487.
•
•
SOLO no longer provides the full
test alert when turned on.
You have inadvertently bypassed
the test alert. To re-engage full
test alert, press and hold the Mute
button at the same time you are
turning SOLO on.
TRO UBLESHO O TING 17
S E R V I C E
IF YOUR SOLO EVER NEEDS SERVICE, PLEASE FOLLOW THESE SIMPLE STEPS:
1 Check the troubleshooting section of this manual. It may have a
solution to your problem.
2 Call us at 1-800-543-1608. We may be able to solve your problem
over the phone. If the problem requires that you send your SOLO to the
factory for repair, we will provide you with a SERVICE ORDER NUMBER,
which must be included on the outside of your shipping box.
ENCLOSE THE FOLLOWING INFORMATION WITH YOUR SOLO:
•
•
•
•
Your Service Order Number
Your name and return address
Your daytime telephone number
A description of the problem you are experiencing.
OUT OF WARRANTY REPAIRS
For out of warranty repairs, include prepayment in the amount you were
quoted by the Escort Customer Service Representative. If the detector has
been damaged, abused or modified, the repair cost will be calculated on a
parts and labor basis. If it exceeds the basic repair charge, you will be
contacted with a quotation. If the additional payment is not received
within 30 days (or if you notify us that you choose not to have your SOLO
repaired at the price quoted), your SOLO will be returned, without repair.
Payment can be made by check, money order or credit card.
MAIL YOUR SOLO TO:
ESCORT
Customer Service Department
Service Order Number ______________
5440 West Chester Road
West Chester, Ohio 45069
For your own protection, we recommend that you ship your SOLO
postpaid and insured. Insist on a proof of delivery and keep the receipt
until the return of your SOLO.
18
SERVICE
W A R R A N T Y
ESCORT ONE YEAR LIMITED WARRANTY
ESCORT warrants your SOLO against all defects in materials and
workmanship for a period of one (1) year from the date of the original
purchase, subject to the following terms and conditions:
•
The sole responsibility of ESCORT under this Warranty is limited to
either repair or, at the option of ESCORT, replacement of the SOLO
detector. There are no expressed or implied warranties, including those
of fitness for a particular purpose or merchantability, which extend
beyond the face hereof. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitations may not apply
to you.
•
•
ESCORT is not liable for any incidental or consequential damages
arising from the use, misuse, or mounting of the SOLO. Some states
do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This Warranty gives you specific rights. You may have other legal rights
which vary from state to state. This Warranty does not apply if the
serial number on the housing of the SOLO has been removed, or if
your SOLO has been subjected to physical abuse, improper
installation, or modification.
TO OBTAIN WARRANTY SERVICE, PLEASE FOLLOW THE SERVICE PROCEDURE OUTLINED
ON PAGE 18.
WARRANTY
19
A C C E S S O R I E S A N D O P T I O N S
To order additional or replacement accessories, call ESCORT toll-free at
1-800-433-3487. The following optional accessories are also available for
SOLO:
SOLO POWER CORD
Provides back-up or alternative power for your SOLO through your
vehicle’s cigarette lighter. NOTE: SOLO is designed for 3V operation and
its unique circuitry will not accommodate a standard 12V power cord.
Using any cord other than the Power Cord/Converter Set designed
specifically for SOLO may cause damage not covered by warranty.)
VISOR CLIP
Allows you to mount SOLO on your vehicle’s sun visor.
NOTE: Due to obstruction by tinting and vehicle headliner, visor
mounting can substantially reduce laser detection range.
HOOK AND LOOP FASTENER
Allows you to mount SOLO to your vehicle’s dashboard.
NOTE: The adhesive backing used on the Hook and Loop Fastener can
permanently mar your vehicle’s dashboard.
CARRYING CASE
Soft case keeps SOLO protected when not in use.
EscortPlus Club benefits are subject to change without notice.
20
ACCESSO RIES AND OPTIO NS
SOLO is designed and manufactured in the USA.
ESCORT
5440 West Chester Road
West Chester, Ohio 45069
CUSTOMER SERVICE: (800) 543-1608
SALES:
(800) 433-3487
Manufactured under one or more of the following U.S. Patents:
4,313,216 4,581,769 4,583,057 4,604,529 4,613,989 4,631,542
4,686,499 4,750,215 4,862,175 4,887,753 4,896,855 4,952,937
4,954,828 5,049,884 5,049,885.
Other Patents Pending.
Product, accessory and features, specifications and pricing are subject to change without
notice.
®
Recyclable
© 1999 ESCORT Inc.
60-000096-22
QUICK REFERENCE GUIDE
To begin using your SOLO, just follow these three simple steps:
a
b
c
Insert two standard AA alkaline batteries into the battery compartment.
Mount your SOLO on the windshield using the windshield mount.
Press the Power-On button to turn SOLO on.
1
2
EasyMount Slot (page 3)
Windshield mount is inserted here.
Power Jack (page 7)
Use optional Power Cord for back-up power source. To purchase, call toll-free
1-800-433-3487.
3
4
5
EasyMount Button (page 7)
Press and slide the windshield mount to adjust mount angle.
Battery Compartment (page 1)
Uses 2 AA alkaline batteries.
Mute Button (page 5)
Briefly press to mute the audio for a specific alert. Press and hold to disengage or
re-engage AutoMute.
6
City Button (page 6)
Briefly press to engage to reduce alerts from X-band intrusion alarms and door
openers common in urban areas. Press and hold to adjust X-band sensitivity
through four possible city sensitivity options to your preferred City setting.
7
8
Dim Button (page 5)
Briefly press to adjust display brightness.
Power/Volume (page 4)
Briefly press to turn SOLO on. Press and hold to adjust SOLO’s audio volume.
Once on, briefly press to turn SOLO off.
9
Power-On Light (page 4)
Blinks when SOLO is on.
10 City Indicator (page 5)
Blinks when City mode is selected.
11 Band Indicators (page 6)
Lights to indicate type of signal detected: X, K, Ka or L.
12 Signal Meter (page 6)
LEDs indicate incoming signal strength or the type of safety signal. Displays
remaining battery life at both power-up and power-down.
(bottom)
2
4
3
1
5
7
8
6
®
Please read the entire
manual to fully
pwr/vol
dim
city
mute
understand SOLO’s
operation and features.
9 10 3 12
|