Memory Stick USB
Reader/Writer
Operating Instructions
MSAC-US40
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
The specified USB cable (supplied) must be used with the equipment in
order to comply with the limits for a digital device pursuant to Subpart B
of Part 15 of FCC Rules.
For the customers in Canada
This class B digital apparatus complies with Canadian ICES-003.
Notice
If static electricity or electromagnetism causes data transfer to
discontinue midway (fail), restart the application or disconnect and
connect the USB cable again.
3-GB
Program©2005 Sony Corporation
Documentation©2005 Sony Corporation
•
, “Memory Stick,” “MagicGate Memory Stick,” “Memory Stick Duo,”
“MagicGate Memory Stick Duo,” “Memory Stick PRO,”
,
“Memory Stick PRO Duo,” “MagicGate,”
, “ATRAC3,” “ATRAC3plus,”
, “Open MG,”
, “SonicStage”
and
are registered trademarks or trademarks of Sony Corporation.
• Microsoft and Windows are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries.
• Pentium is a trademark or registered trademark of Intel Corporation or its
subsidiaries in the United States and other countries.
• Adobe and Adobe Reader are registered trademarks or trademarks of Adobe
Systems, Inc. in the United States and/or other countries.
• Macintosh and Mac OS are trademarks of Apple Computer, Inc., registered in
the U.S. and other countries.
• All other trademarks and registered trademarks are trademarks of their
respective holders.
Furthermore “™” and “®” are not mentioned in each case in this manual.
• CD and music-related data from Gracenote, Inc., copyright c 2000-
2004Gracenote. Gracenote CDDBR Client Software, copyright 2000-2004
Gracenote.This product and service may practice one or more of the following
U.S.Patents: #5,987,525; #6,061,680; #6,154,773, #6,161,132,
#6,230,192,#6,230,207, #6,240,459, #6,330,593, and other patents issued or
pending.
Services supplied and/or device manufactured under license for following
Open Globe, Inc. United States Patent 6,304,523. Gracenote and CDDB are
registered trademarks of Gracenote. The Gracenote logo and logotype, and the
“Powered by Gracenote” logo are trademarks of Gracenote.
• MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer
IIS and Thomson.
Download from Www.Somanuals.com. All Manuals Search And Down4lo-aGd.B
Precautions on use
Pay attention to the following points when using this unit.
• If the body becomes dirty, wipe with a soft cloth. Never use benzine,
alcohol, paint thinner or other solvents. This unit may deform or
malfunction.
• The contents of data cannot be compensated if recording or playing back
is not made due to malfunctions such as “Memory Stick” error.
• To prevent recording or deletion of data on “Memory Stick” set the
“Memory Stick” write-protect switch to “LOCK.”
PNotes
• The access lamp lights when you insert the “Memory Stick” into the unit.
This blinking indicates that the data on the “Memory Stick” is being
accessed. Never remove the “Memory Stick,” turn off the computer or
unplug the USB cable while the access lamp is blinking. Doing so may
damage the data on the “Memory Stick.”
• When disconnecting the USB cable, do not hold it by its cable; hold it by its
connector.
5-GB
Table of contents
Precautions on use ................................................................................................ 5
On “Memory Stick” .............................................................................................. 7
System requirements ............................................................................................ 9
Checking the included items ............................................................................ 12
Supplied applications for Windows ................................................................ 13
Using the operating instructions and help ..................................................... 14
Installing the software on your computer (When Using Windows) .......... 16
Installing the “SonicStage” software on your computer .............................. 18
Connecting this unit to your computer ........................................................... 19
Confirming that connections are completed .................................................. 21
When the removable disk (Memory Stick icon) is not indicated ................ 22
Copying image data recorded on “Memory Stick” to your computer ....... 25
Disconnecting the unit from your computer .................................................. 26
How to Use (When using Macintosh) ............................................................. 28
About “SonicStage” ............................................................................................ 30
Before using “SonicStage” (Be sure to read) ................................................... 32
Launching “SonicStage” .................................................................................... 34
Formatting (initialization) of “Memory Stick” ............................................... 35
Precautions for use of “Memory Stick” ........................................................... 37
Uninstalling (Deleting) the software ............................................................... 38
Troubleshooting .................................................................................................. 39
Restrictions imposed by the copyright protection......................................... 40
Specifications ....................................................................................................... 41
LIMITED WARRANTY ..................................................................................... 42
Download from Www.Somanuals.com. All Manuals Search And Down6lo-aGd.B
On “Memory Stick”
What is “Memory Stick”?
“Memory Stick” is a compact large-capacity IC storage media. The media
can be used not only for transferring data between “Memory Stick”
compatible products, but also as a removable, external storage media for
storing data.
“Memory Stick” is available in standard size and a smaller size called
“Memory Stick Duo.” When “Memory Stick Duo” is inserted into a
Memory Stick Duo Adaptor, the size becomes the same as the standard-
sized “Memory Stick” to allow to use with products that are compatible
with the standard-sized “Memory Stick.”
“Memory Stick PRO” and “Memory Stick PRO Duo” are also available for
handling even larger capacity data.
What is “MagicGate”?
“MagicGate” is the generic name for a copyright-protection technology
developed by Sony. After performing authentication to confirm that
recording or playback can be carried out correctly between a compatible
device and “Memory Stick,” “MagicGate” then encrypts the data.
Copyright-protected data can only be played back on an authenticated
device.
Music and other data that require copyright protection can be recorded
and played back by using a combination of a “MagicGate” compatible
“Memory Stick” and equipment compatible with “MagicGate,” such as
this unit.
Different types of data can be recorded on a single “Memory Stick.”
For example, it is possible to record image data on the remaining empty
section of a “MagicGate” compatible “Memory Stick” containing music
data.
7-GB
“Memory Stick” types that can be used with
this unit
Music
Data transfer/ transfer
“Memory Stick” types
Music transfer (ATRAC3plus/
(MP3 form)
ATRAC3
form)
“Memory Stick” (without MagicGate)
“Memory Stick” (with MagicGate)
“MagicGate Memory Stick”
a
a
a
a
a
a
a
a
×
a
a
a
×
“Memory Stick PRO”
“Memory Stick Duo” (without MagicGate)
“Memory Stick Duo” (with MagicGate)
“MagicGate Memory Stick Duo”
“Memory Stick PRO Duo”
a
a
a
* Sony does not guarantee this unit to operate with all kinds of “Memory
Stick.” It has been checked to operate with any “Memory Stick” up to 4
GB (MSX-4GN) (as of October, 2005). Check the following URL to see
which kinds of “Memory Stick” the unit supports.
* This unit supports parallel data transfer (High speed data transfer). The
reading or writing time varies depending on the media used.
* This unit is not compatible with I/O modules.
PNotes
• Formatting a “MagicGate” compatible “Memory Stick” containing data
will delete all the data, including music data. Be careful not to delete
important data accidentally. Sony can not be held responsible for the data
lost through formatting.
• What you record are for personal enjoyment only. Copyright laws prohibit
other forms of use without the permission of the copyright holder.
• In no event will Sony be liable for the data contents in case download of
recorded material is impeded or music data is corrupted or deleted due to
malfunctions of this unit or the “Memory Stick.”
Download from Www.Somanuals.com. All Manuals Search And Down8lo-aGd.B
System requirements
Recommended Windows environment
• OS: Microsoft Windows 98 Second Edition (Windows 98SE)/Windows
Millennium Edition (Windows Me)/Windows 2000 Professional Service
Pack 3 or later (Windows 2000)/Windows XP Home Edition/XP
Professional/XP Media Center Edition (Windows XP)
* The operating systems mentioned above must be installed on the
computer when shipped from the factory.
* Operation is not guaranteed for upgraded operating systems even if
they are among those mentioned above.
* Not compatible with Windows 98.
* Not compatible with Windows 2000 Professional Service Pack 1/
Service Pack 2.
• CPU: Pentium III 450 MHz or faster processor recommended
• RAM: 128 MB or more
• Available hard disk space: 200 MB or more
(More disk space may be required depending on the version of Windows
you are using. Further space is also required for handling music data.)
• CD-ROM drive
• Sound board (A sound board is required to use “SonicStage.”)
• USB port (This unit supports Hi-Speed USB (USB 2.0).)
• Display: High Color (16-bit) or higher, 800 × 480 pixels or more
(800 × 600 pixels or more recommended.)
Recommended Macintosh environment
• OS: Mac OS 9.2.2/X (v10.2~10.4)
* The operating systems mentioned above must be installed on the
computer when shipped from the factory.
* Operation is not guaranteed for upgraded operating systems even if
they are among those mentioned above.
• RAM: 64 MB or more
• Hard disk: 50 MB or more available hard-disk space
• USB port (This unit supports Hi-Speed USB (USB 2.0).)
PNotes
• Operation is not guaranteed for all computers even if they comply with the
recommended environments.
• “SonicStage” does not support Macintosh.
If you are using a Macintosh computer, it is not possible to transfer music
data that requires copyright protection.
9-GB
When using Windows 2000/Windows XP
The following restrictions apply when “SonicStage” is running under
Windows 2000/Windows XP.
•Installation should take place after you log on as Administrator.
For how to log on using the Administrator account, see the manual
provided with your computer.
•When using the software, log on as an Administrator.
•Do not insert or remove a CD-ROM drive while “SonicStage” is running.
Your important data may get lost.
•Can only be used with Windows 2000 Professional edition with Service
Pack 3 or later installed.
•NTFS format can only be used when standard-installed (installed when
shipped from the factory).
When using this unit on a computer with
Service Pack 3 of Windows 2000 installed
Performing the following operations may cause the unit not to be
recognized by your computer when using this unit on a computer with
Service Pack 3 of Windows 2000 installed:
1. Starting Windows with your computer on or rebooting while the
products in question are connected to your computer’s USB port.
2. Unplugging and plugging in the USB cable that is connecting the unit
and your computer after starting Windows.
tThe products in question will cease to be recognized by your
computer.
If the USB cable is not unplugged, these issues will not occur.
To avoid these issues
When starting Windows with your computer on or when rebooting
Windows, remove the USB cable that is connecting the products in
question and your computer.
10-GB
On System Restore and Windows XP/Windows Me
When using the Windows XP or Windows Me, executing the “System
Restore” item in System Tools may make it impossible to play back the
songs managed by “SonicStage.”
Therefore, be sure to back up the song data managed by “SonicStage”
before you execute “System Restore.”
After “System Restore” has been executed, the backed-up data can be
restored and the songs managed by “SonicStage” can then be played
back again.
For how to back up data, see the Help information for “SonicStage.”
PNote
An error dialog appears if playback of song data is impeded following
execution of “System Restore.” In this case, follow the instructions displayed
on the screen.
11-GB
Checking the included items
• Memory Stick USB Reader/Writer (1)
PNote (The standard size of “Memory Stick” / the Duo size
compatible slot)
You can use both the standard sizes of “Memory Stick” and the sizes of
“Memory Stick Duo” by one slot. (You cannot use both the sizes of
“Memory Stick” at the same time.) When you use the sizes of “Memory
Stick Duo,” do not attach the Memory Stick Duo Adaptor to them.
Do not insert the two or more “Memory Stick” into the slot at the same
time or insert the “Memory Stick” in the opposite direction. It causes
the malfunction of this unit.
• Special USB cable 1 m (1)
• CD-ROM for Windows (MSAC-US40) (1)
PNote
Select the CD-ROM which contains the language you prefer, when installing
“SonicStage.”
* The CD-ROM contains the following software programs.
•Device Driver Software
•“SonicStage”
•Memory Stick Formatter
•Operating Instructions (PDF file)
The data of Operating Instructions for this unit (PDF file) is
MSAC-US40Manual_ENG.pdf
• Operating Instructions for this unit (1)
12-GB
Supplied applications for Windows
The supplied Windows CD-ROM contains the following software
programs.
Device driver (Windows)
The driver must be installed when this unit is used on a Windows
computer.
For how to install the driver software, see page 16.
“SonicStage” (Windows)
“SonicStage” is comprehensive software for enjoying music. With
“SonicStage,” you can enjoy listening to music sources such as music CDs,
etc., or you can import music into the hard disk of your PC for a complete
management of your collection. Furthermore, music data that has been
imported into the hard disk of your PC can also be transferred to a
“Memory Stick” or “Memory Stick Duo” so that they can be enjoyed
outside the PC environment.
PNotes
• “SonicStage” does not support Macintosh.
• This software is not compatible with writing of music data to CD-RW/CD-
R media. Sony will not be liable for any damage of data resulting from
such operation.
• If you have a version of SonicStage other than the one supplied with this
unit, carry out the following step.
t If you have SonicStage Ver.3.2 or later, install the driver from the CD-
ROM.
t If you have SonicStage Ver.3.1 or earlier, install the driver and
SonicStage from the CD-ROM.
Memory Stick Formatter (Windows)
This is a software program for formatting (initialization) of “Memory
Stick.” Formatting deletes all the data recorded on a “Memory Stick.”
In order to maintain the compatibility of a “Memory Stick” when using it
with compatible products, always use this software when formatting
“Memory Stick” on this unit.
PNote
Formatting a “Memory Stick” to which data has already been written will
delete the existing data. Be careful not to delete important data by mistake.
13-GB
Using the operating instructions and
help
Using the Operating Instructions on the CD-
ROM
For details on how to use this unit, see these Operating Instructions.
Adobe Reader from Adobe Systems Incorporated is required to view PDF
files.
How to use Adobe Reader is described in the following.
Screen view
Right frame
Left frame
•Left frame
Each page of the Operating Instructions appears as a thumbnail.
When you click on the thumbnail corresponding to the page that you
want to view, the page is shown in the “Right frame.”
•Right frame
Shows each page.
For details on how to use Adobe Reader, see the online Help manual for
Adobe Reader.
14-GB
How to use the Help (When Using Windows)
The following applications feature separate online Help manuals.
• “SonicStage”
• Memory Stick Formatter
For details on how to use each of the application software programs, see
the respective Help manuals.
How to use the Help manuals is described as follows.
Screen view
Tab
Right frame
Left frame
• Left frame
Contents or Keywords are displayed here.
• Right frame
Displays explanations. Clicking underlined parts in the text displays
related explanations.
15-GB
Installing the software on your
computer (When Using Windows)
PNote
Be sure to install the supplied software before you connect this unit to your
computer.
Do not perform the installation while this unit is connected to your
computer.
Restart your computer when installation is completed, and then connect this
unit to your computer.
Use the following procedure to install the software.
A part of the installation may take place automatically.
Installing the device driver on your computer
PNote
Simultaneously with the installation of the device driver, the “Memory Stick
Formatter” and the operating instructions (PDF file) are also installed on
your computer.
1
Turn on your computer.
At this point, do not connect this unit to your computer.
Close all running applications.
To install the device driver when you are using Windows 2000 or
Windows XP, you must log on with Administrator rights.
16-GB
2
3
Insert the supplied CD-ROM (MSAC-US40) into the CD-ROM
drive on your computer.
The Installer launcher starts up automatically.
To install a driver, click the [Driver] button in the menu.
Carefully read the License Agreement, and then click the
[Agree] button.
When you click the [Agree] button, installation of the driver starts.
4
5
6
Click the [Next] button as prompted on the screen.
When you click [Finish], the driver installation is completed.
Following this, installation of the “Memory Stick Formatter”
starts.
Click the [Next] button as prompted on the screen.
7
8
When you click [Finish], installation of “Memory Stick
Formatter” is completed.
To use “Memory Stick Formatter,” select [Start] – [Programs] –
[Memory Stick Utility] – [Memory Stick Formatter].
Following this, installation of the operating instructions (PDF
file) is performed automatically.
When installation of the operating instructions is completed, the
application selection screen returns.
To end installation of the software at this point, click [Exit].
If you do so, “SonicStage” is not installed.
To view the operating instructions, select [Start] – [Programs] – [Sony
Memory Stick Reader Writer] – [MSAC-US40 Instructions].
PNote
Adobe Reader from Adobe Systems Incorporated is required for
viewing the operating instructions (PDF file).
17-GB
Installing the “SonicStage” software on
your computer
1
Do as follows to install “SonicStage.”
Click the [SonicStage] button in the menu.
2
Carefully read the License Agreement, and then click the [Yes]
button.
When you click the [Yes] button, installation of “SonicStage” starts.
3
4
Click the [Next] button as prompted on the screen.
Select the folder in which you want to install “SonicStage.”
To change the folder suggested for the installation, click the [Browse]
button and then select the folder. When the storage destination folder
is decided, click the [Next] button.
5
6
Click the [Done] button.
Restart your computer.
PNote
Be sure to connect this unit only after you have restarted your computer.
18-GB
Connecting this unit to your computer
PNote
Be sure to install the supplied software before you connect this unit to your
computer. Restart your computer following installation.
Connect the USB port on this unit to a USB port on your computer using
the special USB cable supplied.
USB port
USB port
Mini-B
connector
A connector
Access lamp
* Serial number
(8-digit number on the
backside of this unit)
On the special USB cable
A connector: This is plugged into the USB port on the computer. Any
ports can be used if the computer is provided with multiple
USB ports.
Mini-B connector: This is plugged into the USB port on this unit.
1
2
Firmly insert the Mini-B connector of the USB cable into the
USB port on this unit as far as it will go.
Plug the A connector of the USB cable into a USB port on your
computer.
•The “Found New Hardware Wizard” starts up and installation of
the driver begins. Depending on the OS, the driver installation may
take place automatically.
•The location of the USB port on the computer differs with the
computer used.
•When using a computer with multiple USB ports, do not connect
other devices, with the exception of a standard mouse and keyboard,
to USB ports at the same time as this unit. When using a desktop
computer, use a USB port on the main unit of the computer. For
details, see “Recommended ways for connecting this unit” on page
20.
19-GB
Recommended ways for connecting this unit
The operation of this unit has been confirmed when connected to the
computer in either of the following ways.
When this unit is connected to a USB port on the computer main unit, and
nothing is connected to other USB ports on the computer main unit.
When, on a computer with a USB keyboard and mouse as standard
equipment, the USB keyboard is connected to one of the USB ports on the
computer main unit, and this unit is connected to another USB port on the
computer main unit with the supplied USB cable.
PNotes
• When two or more USB devices except standard equipment are connected
to one computer, and both are used simultaneously, operation is not
guaranteed depending on the USB devices.
• Make sure to connect the supplied USB cable to a USB port on the
computer main unit. Operation is not guaranteed if the cable is connected
via the keyboard or a USB hub, etc.
• Not all operations are guaranteed on all computers running under the
recommended environment.
• Make sure to use the specified USB cable (supplied) to connect to your
computer.
20-GB
Confirming that connections are
completed
In the following, Windows XP is used for instructions. Depending on the
OS type and the settings, the screens may look different.
1
2
Open the “My Computer” folder.
The “My Computer” folders appear.
Confirm that the newly recognized Memory Stick-MG(F:) icon
is shown.
PNote
Depending on the computer used, the drive letter (F:) may be different.
The connection is completed when the Memory Stick-MG(F:) icon is
shown.
It may take a little while before the Memory Stick-MG(F:) icon appears.
PNotes
• Depending on the OS type used and the “Memory Stick,” the displayed
icon may appear as “Removable Disk (F:)” instead of “Memory Stick-
MG(F:).”
• If the Memory Stick icon is not shown, the device driver may not be
installed correctly. Perform the procedures described on the following
page. When using another “Removable Disk,” plural “Removable Disk”
icons appear.
21-GB
When the removable disk (Memory
Stick icon) is not indicated
A separate device driver may already have been installed. Connect this
unit to your computer, and then perform the following procedure.
– When using Windows 2000/Windows XP –
Log on as Administrator or using a user ID that has administrative
privilege.
1
Double-click the “System” icon on the “Control Panel.”
The “System Properties” screen appears.
2
Check if the device driver has already been installed.
1 Click the [Hardware] tab on the
“System Properties” screen.
2 Click [Device Manager].
The “Device Manager” screen
appears.
22-GB
2
(Continued)
3 Click [View].
4 Click [View devices by type].
5 Double-click [Other devices].
6 Check whether [? MSAC-
US40] preceded by the “?”
symbol is shown.
3
Delete the driver if installed.
If you use the procedure described in Step 2 and confirm that
[? MSAC-US40] is shown under “Other devices” in the “View devices
by type” display, a separate device driver has already been installed.
Use the following procedure to delete this driver.
Do not delete other devices than [? MSAC-US40].
1 Right-click on [? MSAC-US40].
2 Click on [Remove]. The “Confirm Device Removal” screen
appears.
3 Click the [OK] button. The device is removed.
4 Restart your computer after disconnecting this unit from the
computer.
Install the device driver again by performing the procedure from
Step 1 described on page 16.
PNote
If you delete other devices than [? MSAC-US40], your computer may no
longer operate normally.
23-GB
– When using Windows 98SE/Windows Me –
1
2
Double-click the “System” icon on the “Control Panel.”
The “System Properties” screen appears.
Check if the device driver has already been installed.
1 Click the [Device Manager] tab on the “System Properties” screen.
2 Double-click [Other devices].
3 Check whether [? MSAC-US40] preceded by the “?” symbol is
shown.
3
Delete the driver if installed.
If you use the procedure described in Step 2 and find that [? MSAC-
US40] is shown under “Other devices,” a separate device driver has
already been installed.
Use the following procedure to delete this driver.
Do not delete other devices than [? MSAC-US40].
1 Click on [? MSAC-US40].
2 Click on [Remove]. The “Confirm Device Removal” screen appears.
3 Click the [OK] button. The device is removed.
4 Restart your computer after disconnecting this unit from the
computer.
Install the device driver again by performing the procedure from
Step 1 described on page 16.
PNote
If you delete other devices than [? MSAC-US40], your computer may no
longer operate normally.
24-GB
Copying image data recorded on
“Memory Stick” to your computer
If the USB cable used to connect this unit and your computer is
disconnected, the computer will no longer be able to recognize this unit
and the image data stored on the “Removable Disk (“Memory Stick”)” can
no longer be viewed on the computer. If you copy the image data stored
on the “Memory Stick” to your computer, the image data can be displayed
and processed on your computer even if this unit is not connected to your
computer.
When the USB cable is disconnected, the Memory Stick-MG(F:) icon
disappears.
For how to copy image data to your computer, see the manual for your
computer.
25-GB
Disconnecting the unit from your
computer
– For customers using Windows Me/Windows 2000/Windows XP –
Perform the procedure described below before disconnecting the USB
cable from the computer.
•The screens shown in Windows XP are used in the following
explanations.
The screens may differ slightly depending on the type of OS used.
•Customers using Windows 98SE do not need to perform this procedure.
1
Click the “Unplug or Eject Hardware” icon in the task tray in
the lower right corner of the screen.
Click this icon.
A message
appears.
This section is the task tray.
2
Click “Safely remove Sony Memory Stick USB Reader/Writer
(MSAC-US40)-Drive (F:).”
Click this section.
A message appears after a
little while.
* The drive letter “(F:),” etc. differs depending on the computer used.
26-GB
3
[“Sony Memory Stick USB Reader/Writer (MSAC-US40) can be
safely removed.”] is displayed.
In this condition, you can safely remove this unit from your computer.
PNote
The indications may be different depending on the OS that you are using.
PNotes
• When you just want to remove the “Memory Stick” from this unit, the
procedure described above is not required.
• Do not remove the “Memory Stick” from this unit while the access lamp is
blinking. Data on the “Memory Stick” could be corrupted.
• When you carry out this operation, this unit is not recognized by your
computer. To make this unit recognize again, disconnect the USB cable
from your computer and connect the USB cable to your computer again.
27-GB
How to Use (When using Macintosh)
You can use the driver provided as a standard feature of the OS.
Operate as described in the following.
You can use this unit without installing the driver, by
simply connecting this unit to your computer.
1
2
Turn on your computer.
Insert “Memory Stick” to this unit and connect the USB port
on this unit with a USB port on the computer main unit using
the special USB cable supplied.
See page 19 for how to connect this unit and your computer.
3
4
Driver installation starts automatically and the driver is
installed on the computer.
When driver installation is completed, a drive icon of this unit
appears on the desktop and this unit can now be used.
PNote
The drive icon of this unit is not displayed on the desktop when “Memory
Stick” is not inserted to this unit.
Removing this unit from your computer or removing
“Memory Stick” from this unit.
1
2
3
Close the software used by this unit.
Confirm that the access lamp is not blinking.
Drag the drive icon of this unit to the Trash icon.
Alternatively, place the drive icon of this unit in the selected state and
select “Eject” from the “Special” menu in the upper left of the screen.
4
Remove this unit from your computer or remove “Memory
Stick” from this unit.
28-GB
PNotes
•The access lamp lights when you insert the “Memory Stick” into the unit.
This blinking indicates that the data on the “Memory Stick” is being
accessed. Never remove the “Memory Stick,” turn off the computer or
unplug the USB cable while the access lamp is blinking. Doing so may
damage the data on the “Memory Stick.”
•Unplugging the USB cable or removing the “Memory Stick” in this unit,
without performing the operations above, may cause damage to the
“Memory Stick.” Unplug the USB cable or remove the “Memory Stick”
after performing these operations.
Sony will not be liable for any damage caused as a result of not following
the instructions above.
29-GB
About “SonicStage”
“SonicStage” is comprehensive software for enjoying music.
With “SonicStage,” you can enjoy listening to music sources such as music
CDs, etc., or you can import music into the hard disk of your PC for a
complete management of your collection.
Furthermore, music data that has been imported into the hard disk of your
PC can also be transferred to a “Memory Stick” or “Memory Stick Duo” so
that they can be enjoyed outside the PC environment.
Using “SonicStage” to listen to various music
sources
With “SonicStage,” you can play back the following music sources using
the simple, integrated mouse operations:
•Devices/tracks recorded on a media connected to the USB port of your
PC. (This is available using the main unit and “Memory Stick.”)
•Music CD
•Music files on your PC
•Music files provided by Internet music distribution services (EMD
services).
Creating a music database by importing music
from various music sources
“SonicStage” uses the music database “My Library” to manage music files
that are stored in your PC.
Music files can be imported into “My Library” from various music sources
using the following methods:
•Record tracks from a music CD into “My Library.”
•Import music files already existing on your PC into “My Library.”
•Download music files from an Internet music distribution service and
import them into “My Library.”
30-GB
Transferring imported music data to another
device/media for listening outside the PC
environment
Music files imported into the hard disk (“My Library”) of your PC can be
transferred to a “Memory Stick.”
Music files transferred to a “Memory Stick” can be played outside the PC
environment using devices such as a portable audio player, etc.
For various uses of “SonicStage,” please refer to the “SonicStage” Help.
PNote
There are some WAV format, MP3 format and WMT compatible music
files that cannot be imported depending on sampling rate, etc. For
details concerning music files that cannot be imported, please refer to
“Importable Files” in “SonicStage” Help.
31-GB
Before using “SonicStage” (Be sure to
read)
Before using “SonicStage,” please read the following cautionary items.
Cautions concerning launching “SonicStage”
and other “OpenMG” compatible software
Do not launch “SonicStage” and other “OpenMG” compatible software
(software capable of running/managing “OpenMG” format files)
simultaneously. Doing so may cause music files stored on the PC hard disk
or devices/media to be damaged, and rendered unusable.
Cautions concerning using “SonicStage” and
other software at the same time
Please note the following when running “SonicStage” and other software
at the same time.
When recording tracks from a music CD using “SonicStage,” do not run
other software capable of music CD playback. Recording of the music CD
may not perform properly.
When running other software while playing back music files using
“SonicStage,” the sound may pause momentarily.
32-GB
Cautions when running Windows XP/Windows
Me system tool “System Restore”
Running “System Restore,” a system tool built in Windows XP and
Windows Me, may cause a malfunction in management data resulting in
all recorded or imported files to become unusable.
In order to prevent the loss of important music data, use the “SonicStage”
backup tool to backup music data before running “System Restore” on
your system. After using “System Restore,” saved music data can be made
to play back by restoring with the “SonicStage” back up tool.
For the use of the “SonicStage” backup tool, please refer to the
“SonicStage” Help.
Writing to a CD-RW/CD-R disc
The “SonicStage” supplied with this unit is not compatible with writing of
music data to CD-RW/CD-R media.
Sony will not be liable for any loss of data resulting from such operation.
33-GB
Launching “SonicStage”
From the [Start] button of Windows, click [All Programs] –
[SonicStage] – [SonicStage].
“SonicStage” is launched and the main window appears.
PTips
•When using an operating system other than Windows XP, launch
“SonicStage” by clicking from the [Start] button of Windows:
[Programs] – [SonicStage] – [SonicStage].
•“SonicStage” can also be launched by:
– Double clicking a SonicStage icon on the desktop if displayed.
(When using Windows XP, icons that have not been used for some
time are deleted from the desktop depending on the setting. If the
SonicStage icon does not appear on the desktop, launch from the
start menu.)
– Double click music files associated for playback on “SonicStage”
using Windows Explorer, etc.
For various uses of “SonicStage,” please refer to the “SonicStage” Help.
34-GB
Formatting (initialization) of “Memory
Stick”
This deletes all the data recorded on a “Memory Stick.” When formatting
on this unit, be sure to use the supplied “Memory Stick Formatter”
software program, following the procedures outlined below. Operation on
a Handycam or other “Memory Stick” compatible products is not
guaranteed for a “Memory Stick” formatted on a computer without the use
of the “Memory Stick Formatter” software program.
For the details on how to use the “Memory Stick Formatter,” refer to the
manual supplied with the “Memory Stick Formatter.” You can download
the “Memory Stick Formatter” at the following Web Site.
PNote
If you format a “Memory Stick” that contains recorded data, the already
recorded data will be deleted. Be careful not to inadvertently delete
important data.
1
2
3
Insert a “Memory Stick” into this unit.
Start “Memory Stick Formatter.”
After confirming that the drive is selected on which the
“Memory Stick” is recognized to have been mounted, click
[Start formatting]. Formatting begins.
PNote
Never remove this unit from the computer while formatting the “Memory
Stick.” The data on the “Memory Stick” may be damaged.
35-GB
Write-protecting data
A “Memory Stick” is equipped with a write-protect switch to ensure that
important data is not deleted by mistake. (Some of “Memory Stick”
(“Memory Stick Duo”) are not equipped with a write-protect switch. If you
use a “Memory Stick” (“Memory Stick Duo”) unequipped with the write-
protect switch, be careful not to write data or delete data by mistake.)
Sliding this switch to the left or right enables or prevents writing of data to
the “Memory Stick.”
•Write enable
Data can be written.
•Write protect
When the switch is moved to the right, the condition becomes the one in
which data cannot be written to the “Memory Stick.” Data can be read
out but writing is prevented.
Underside of “Memory Stick”
Write enable
Write protect
Data read/write speed
The data read/write speed differs depending on the “Memory Stick” and
product combination that you are using.
36-GB
Precautions for use of “Memory Stick”
How to affix
labels
A
B
C
• Recording, editing and deleting are prevented when the write-protect
switch is set to the “LOCK” position. B
• Use a pointed object to move the write-protect switch on the “Memory
Stick Duo.” (Some of “Memory Stick” (“Memory Stick Duo”) are not
equipped with a write-protect switch.)
• Never remove the “Memory Stick” while the access lamp is blinking
(while data is being read/written).
• Data may be corrupted in the following cases.
– If the “Memory Stick” is removed or the power of this main unit is
turned off while the access lamp is blinking (while data is being read/
written)
– When used in a location subject to static electricity or electrical noise
• Always backup important data. Sony does not accept liability for damage
of the data.
We cannot accept responsibility in the event that data is lost or damaged
and the unit is damaged, while using this unit.
• Data copyright protected by “MagicGate” can only be used with a
“MagicGate” compatible “Memory Stick.”
• Do not affix any label other than those specially provided to the
“Memory Stick.” C
• When affixing labels, affix these at the designated positions. Labels
should not protrude from the edges of the “Memory Stick.”
• Do not apply excessive force when writing in the memo area of a
“Memory Stick Duo.”
• When transporting or storing a “Memory Stick,” place it in the supplied
storage case.
• Do not touch the connector section with fingers or metallic objects. A
• Do not bend, drop or subject the “Memory Stick” to strong impacts.
• Do not attempt to disassemble or modify the “Memory Stick.”
• Do not wet with water.
• Do not use or store in the following environments:
– Where the temperature is too high (in a car with closed windows
during summer, in direct sunlight, near a heater, etc.)
– Humid or corrosive locations
37-GB
Uninstalling (Deleting) the software
– In the case of Windows 98SE/ Windows Me –
1
Select [Settings] from the [Start] menu and then click [Control
Panel].
The “Control Panel” screen appears.
2
3
Double-click the “Add/Remove Programs” icon.
The “Add/Remove Programs Properties” dialog box appears.
Select the software to be removed (“SonicStage,” Memory
Stick Formatter) from the list of software programs that can
be automatically removed, and then click [Add/Remove].
The selected software programs are uninstalled.
– In the case of Windows 2000/Windows XP –
After logging on as Administrator, perform the procedure described
below. For how to log on as Administrator, see the manual for the
computer that you are using.
1
Using Windows 2000: Select [Settings] from the [Start] menu
and then click [Control Panel].
Using Windows XP: Click [Control Panel] from the [Start]
menu.
The “Control Panel” screen appears.
2
Using Windows 2000: Double-click the “Add/Remove
Programs” icon.
Using Windows XP: Double-click the “Add/Remove Programs”
icon.
The “Add/Remove Programs” dialog box appears.
3
4
Click “Change/Remove.”
Select the software to be removed (“SonicStage,” Memory
Stick Formatter) from the list of “Currently installed
programs,” and then click [Change/Remove] ([Change and
Remove] in the case of Windows XP).
The selected software programs are uninstalled.
38-GB
Troubleshooting
Cause/Solution
Symptom
•Not connected correctly.
t Connect correctly. (Page 19)
•In addition to this unit, another device is
connected to the USB port on the
computer.
The Memory Stick icon
(Removable disk) is not
displayed.
t Disconnect other USB devices than
this unit. Or turn off the power and
reboot.
•The driver is not installed.
t Install the driver from the supplied
CD-ROM. (Page 16)
•No “Memory Stick” inserted.
t Insert a “Memory Stick.”
The “Memory Stick”
cannot be accessed from
Explorer or My
Computer.
•Foreign matter adhering to the
connector section of the “Memory
Stick.”
The access lamp is not on
when a “Memory Stick” is
inserted.
t Check whether dust or dirt is
adhering to the connector section of
the “Memory Stick.”
Remove any foreign matter and
insert the “Memory Stick” again.
Music data can no longer •The System Restore function found in
be used on the computer
Windows Me and Windows XP have
been executed. (Page 11)
t When you have backup data, restore
the backup data to the computer.
For how to use the backup tool, see
the Help manual for “SonicStage.”
39-GB
Restrictions imposed by the copyright
protection
The “SonicStage” software employs “OpenMG” Sony-developed copyright
protection technology to safeguard the copyright of music content. It
enables you to enjoy a wide range of music via online music distribution
services.
The number of times you can record or play back may be restricted due to
the copyright protection of music content.
40-GB
Specifications
Interface: Hi-Speed USB (USB 2.0)
General
Operating voltage
Power consumption
DC 5 V (supplied via USB cable)
Max. 500 mA (during operation)
Max. 0.5 mA (PC suspend time)
Approx. 39 mm × 18 mm × 86 mm
(1 9/16 × 23/32 × 3 1/2 in.)
(Width × Height × Depth)
External dimensions
Mass
Approx. 28 g (1 oz.)
(not including “Memory Stick”)
Temperature 0 °C to 40 °C (32 °F to 104 °F)
(condensation not allowed)
Humidity 20 % to 80 %
Operating conditions
(condensation not allowed)
Design and specifications are subject to change without notice.
If you have any questions/comments related to this product, please visit
our Customer Support website at
41-GB
LIMITED WARRANTY
Sony Electronics Inc. (in the United States) and Sony of Canada Ltd (in
Canada) (“SONY”) warrants this Product from defects in material and
workmanship for a period of one (1) year from date of original purchase.
SONY will repair or replace the Product with new or refurbished product, at
its option, at no charge during the one (1) year warranty period. For purposes
of this Limited Warranty, “refurbished” means a product or part that has been
returned to its original specifications. To obtain warranty service within the
United States, you must take the Product, or deliver the Product freight
prepaid, in either its original packaging or packaging affording an equal
degree of protection, to any authorized SONY service facility. To obtain
warranty service within Canada, you must take the Product to the authorized
SONY dealer where you purchased the Product, or to a SONY service
facility. Proof of purchase is required in the form of a dated bill of sale or
receipt which evidences that the Product is within the limited warranty period.
BE SURE TO REMOVE ALL SOFTWARE, FILES, OR ANY OTHER DATA
STORED ON YOUR MEDIA PRIOR TO SENDING THIS PRODUCT TO
SONY. SONY IS NOT LIABLE FOR ANY LOSS, DAMAGE OR
CORRUPTION OF THESE ITEMS.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS LIMITED
WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. SONY
SHALL NOT BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR
CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING BUT
NOT LIMITED TO, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OR
CORRUPTION OF DATA, LOSS OF USE OF THE PRODUCT OR ANY
ASSOCIATED EQUIPMENT, DOWNTIME AND USER'S TIME OR FOR
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR CONDITION,
BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY OR ANY
OTHER LEGAL THEORY RELATED TO THIS PRODUCT. EXCEPT TO
THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTY/CONDITION OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION
TO THE DURATION OF THIS WARRANTY. ANY WARRANTY FOR
INTELLECTUAL PROPERTY INFRINGEMENT IS HEREBY DISCLAIMED.
Some states/jurisdictions do not allow the exclusion or limitation of incidental
or consequential damages, or allow limitations on how long an implied
warranty/condition lasts, so the above limitations or exclusions may not apply
to you. This Limited Warranty gives you specific legal rights, and you may
have other rights which vary from state to state, territory or province.
In the United States contact: Sony Direct Response Center,12451 Gateway
In Canada contact: Sony of Canada Ltd. 115 Gordon Baker Road, Toronto,
Ontario M2H 3R6
42-GB
Sony Corporation
|
Sharp Microwave Oven R 1600 User Manual
Sharp MiniDisc Player MD SR60E User Manual
Sony Computer Monitor TRINITRON User Manual
Sony Speaker System SS NX1 User Manual
Sony Stereo Amplifier XM ZR1252 User Manual
Sony Stereo Receiver STR DA2ES User Manual
SOYO Computer Hardware SY 7IZB+ User Manual
StarTechcom Laptop RACKCONV1701 User Manual
State Industries Water Heater GPO 86 199 User Manual
Superior Indoor Fireplace GHC GRD 5500 User Manual