Safety and Support
PSP-3002
PSP-3003
4-115-361-24(1)
•
If you use a pacemaker or other medical device, consult your doctor
or the manufacturer of your medical device before using the wireless
networking feature.
Photosensitivity
Always play in a well lit environment. Take regular breaks, 15 minutes
every hour. Avoid playing when tired or suffering from lack of sleep.
Some individuals are sensitive to flashing or flickering lights or
geometric shapes and patterns, may have an undetected epileptic
condition and may experience epileptic seizures when watching
television or playing videogames. Consult your doctor before playing
videogames if you have an epileptic condition and immediately should
you experience any of the following symptoms whilst playing:
dizziness, altered vision, muscle twitching, other involuntary
movement, loss of awareness, confusion and/or convulsions.
•
•
•
•
Keep the PSP® system at least 20 cm away from a pacemaker or
other medical devices when using the wireless networking feature.
Do not carry the PSP® system in a breast pocket if you use a
pacemaker.
Turn off your PSP® system immediately, if you have any reason to
suspect that interference is occurring with your pacemaker.
Do not use the wireless networking feature in the following
locations:
– Areas where its use is prohibited, such as in aeroplanes or
hospitals. Abide by medical institution regulations when using the
PSP® system on their premises. Additionally, you may be
violating air safety regulations punishable by fines by using the
wireless networking feature in an aeroplane or by using the PSP®
system during takeoff or landing.
Repetitive Motion Injuries
Avoid prolonged use of the PSP® system. Take a 15 minute break
every hour. Stop using the PSP® system immediately if you experience
an unpleasant sensation or pain in your hands, wrists or arms. If the
condition persists, consult a doctor.
– Crowded areas.
– Areas near fire alarms, automatic doors and other types of
automated equipment.
Use caution when using the wireless networking feature in a vehicle,
as radio waves may affect electronic equipment in some vehicles.
•
Headphones
Adjust your headphone volume so that surrounding sounds can be
heard. If you experience ringing or any discomfort in your ears,
discontinue use of your Headphones.
Radio waves
Radio waves may affect electronic equipment or medical devices (for
example, pacemakers), which may cause malfunctions and possible
injuries.
WARNINGS
3
About DNAS
Sony Computer Entertainment Inc. uses DNAS (Dynamic Network
Authentication System), a proprietary authentication system, to help
protect copyright and security in connecting the PSP® system to a
network. DNAS may retrieve information about a user's hardware and
software for authentication, copy protection, account blocking, system,
rules, or game management and other purposes. The information
collected does not identify the user personally. The unauthorised
transfer, exhibition, export, import or transmission of programs and
devices circumventing its authentication scheme may be prohibited by
law.
System Software
The System Software included within this product is subject to a
limited licence from Sony Computer Entertainment Inc. Refer to
Where you see either symbol on any of our electrical products, batteries
or packaging, it indicates that the relevant electrical product or battery
should not be disposed of as general household waste in Europe. To
ensure the correct waste treatment of the product and battery, please
dispose of them in accordance with any applicable local laws or
requirements for disposal of electrical equipment/batteries. In so doing,
you will help to conserve natural resources and improve standards of
environmental protection in treatment and disposal of electrical waste.
This symbol may be used on batteries in combination with additional
chemical symbols. The chemical symbols for mercury (Hg) or lead
(Pb) will appear if the battery contains more than 0.0005% mercury or
more than 0.004% lead.
WARNINGS
4
Table of contents
About the PSP® system
documentation
The PSP® (PlayStation®Portable) system documentation includes the
following:
Safety and Support (this document)
This document contains safety information related to the use of the
PSP® system, troubleshooting, specifications and other information.
Quick Reference
This document contains information on basic hardware operations of
the PSP® system.
User's Guide
(http://manuals.playstation.net/document/)
This online document is accessed through the Internet and contains
detailed information related to use of the PSP® system software.
Information about system functionality published in this document
may vary from the information for your PSP® system, depending on
the system software version in use.
About the PSP® system documentation
5
Before use
Use and handling
•
•
•
•
Use in a well-lit area and keep the screen a safe distance from your
face.
Precautions
Avoid prolonged use of the PSP® system. To help prevent eyestrain,
take a break of about 15 minutes during every hour of play.
Exercise care when setting the volume. If you set the volume too
high, it may harm your hearing or damage the speakers.
Keep the system and accessories out of the reach of small children,
as small children may swallow small parts such as Memory Stick
Duo™.
Do not use the system while driving or riding a bicycle. Looking at
the screen or operating the system while driving an automobile or
riding a bicycle may result in a traffic accident.
Carefully read the supplied instructions before use. Retain them for
future reference.
Accessory compatibility
Some accessories designed for use with the PSP-1000 series
and/or the PSP-2000 series are not compatible with the PSP-
•
•
•
•
Do not use the system or accessories near water.
Safety
Use only attachments/accessories specified by the manufacturer.
Do not expose the system or accessories to high temperatures, high
humidity, or direct sunlight.
Do not leave the system or accessories in a car with the windows
closed (particularly in summer).
Do not expose the system or accessories to dust, smoke or steam.
Do not allow liquid or small particles to get into the system or
accessories.
Do not place the system or accessories on surfaces that are tilted,
unstable or subject to vibration.
Do not throw, drop or step on the system or accessories, and do not
subject the devices to strong physical shock. Sitting down with the
PSP® system in a pocket or placing the system in the bottom of a
backpack along with heavy objects may cause damage to the system.
Do not forcibly twist the PSP® system or expose the system to strong
physical shock during gameplay, as doing so can damage the system
or cause the disc cover to open, ejecting the disc. Handle the analog
stick with care.
This product has been designed with the highest concern for safety.
However, any electrical device, if used improperly, has the potential for
causing fire, electrical shock or personal injury. To help ensure
accident-free operation, follow these guidelines:
•
•
•
•
•
Observe all warnings, precautions and instructions.
Regularly inspect the AC Adaptor or the AC Power Cord for damage
and for dust build-up around the power plug or electrical outlet.
Stop use, unplug the AC Adaptor or the AC Power Cord from the
electrical outlet and disconnect any other cables immediately if the
device functions in an abnormal manner, produces unusual sounds or
smells or becomes too hot to touch.
•
•
•
•
•
Do not put heavy objects on the system or accessories.
Precautions
6
•
•
Do not touch or insert foreign objects into the connectors of the
system or accessories.
Do not touch the system or AC Adaptor for an extended period of
time while in use. Depending on the conditions of use, the system or
the AC Adaptor may reach temperatures of 40° C or more. Extended
contact under these conditions may cause low-temperature burns*.
•
•
When disconnecting the AC Adaptor or the AC Power Cord, hold it
by the plug and pull straight out from the electrical socket. Never pull
by the cord and do not pull at an angle.
Do not use the system to play games, video or music when the
system is covered with any type of fabric. If you want to pause or
temporarily store the system while playing games, video or music,
put the system in Sleep Mode before placing it in the case or
covering.
Do not connect the AC Adaptor or the AC Power Cord to a voltage
transformer or inverter. Connecting the AC Adaptor or the AC
Power Cord to a voltage transformer for overseas travel or an
inverter for use in an automobile may cause heat to build up in the
AC Adaptor and may cause burns or a malfunction.
The socket-outlet shall be installed near the equipment and shall be
easily accessible.
*
Low-temperature burns are burns that occur when the skin is in contact
with objects of the AC relatively low temperatures (40° C or more) for
an extended period of time.
•
•
When connecting the system to a plasma or projection* TV, do not
leave a still image on the TV screen for an extended period of time,
as this may leave a faint image permanently on the screen.
*
Except LCD screen types
•
AC Adaptor* and AC Power Cord use
*
The PSP-3003 model comes with a combined AC Adaptor and AC Power
Cord.
•
•
•
•
Do not touch the plug of the AC Adaptor or the AC Power Cord with
wet hands.
Do not touch the AC Adaptor, the AC Power Cord or the system, if
connected to an electrical outlet, during an electrical storm.
Do not use a power source other than the supplied (or approved
replacement) Battery Pack, AC Adaptor or AC Power Cord.
Do not allow dust or foreign matter to build up around the system or
accessory connectors. If there is dust or foreign matter on the
system's connectors, the AC Adaptor or the AC Power Cord, wipe it
off with a dry cloth before connecting. Dust or other matter on the
connectors can result in fire or electrical shock.
Unplug the AC Adaptor or the AC Power Cord from the electrical
outlet, disconnect any other cables and remove the Battery Pack from
the system before cleaning or when you do not intend to use the
system for an extended period of time.
LCD screen
•
•
The LCD screen is made of glass and may crack if subjected to
excessive force.
Black (dark) pixels and continuously lit pixels may appear in certain
locations on the LCD screen. The appearance of such spots is a normal
occurrence associated with LCD screens and is not a sign of a system
malfunction. LCD screens are made using highly precise technology.
However, a very small number of dark pixels or continuously lit pixels
exist on each screen. Also, a distorted image may remain on the screen
for several seconds after the system has been turned off.
Direct exposure to sunlight may damage the system's LCD screen.
When using the system in a cold environment, you may notice
shadows on the graphics or the screen may appear darker than usual.
This is not a malfunction, and the screen will return to normal when
the temperature rises.
•
•
•
•
Protect the AC Adaptor or the AC Power Cord from being walked on
or compressed particularly at plugs and the point where they exit
from the system.
Precautions
7
•
Do not leave still images displayed on the screen for an extended
period of time. This may cause a faint image to be left permanently
on the screen.
•
•
Do not use or store a Memory Stick Duo™ in the following:
– Places subject to high temperatures, such as in a hot vehicle
– Locations exposed to direct sunlight
– Locations that are very humid or conducive to corrosion
When using Memory Stick Duo™ media without an erasure
prevention switch, take care not to overwrite or delete data by
accident. If your Memory Stick Duo™ media has an erasure
prevention switch, you can prevent data from being saved, edited, or
deleted by setting the switch in the LOCK position.
About the "pickup"
Do not touch the "pickup" located inside the disc cover of the system.
Touching the pickup may damage the system.
Recorded data
Do not use the Memory Stick Duo™ in the following ways, as doing
so may result in data loss or corruption:
•
Removing the Memory Stick Duo™ or turning off the system while
it is loading or saving data or being formatted.
Using it in a location that is exposed to static electricity or electrical
interference.
•
Pickup
If, for any reason, software or data loss or corruption occurs,
it is usually not possible to recover the software or data. Sony
Computer Entertainment Inc. and its subsidiaries and
affiliates accept no liability for damages, costs or expenses
arising from software, data loss or corruption.
Memory Stick Duo™
For best results, follow these guidelines:
Cases and coverings
•
When placing the PSP® system in a commercially available case,
turn off the power or put the system in sleep mode. Do not use the
system while it is in the case. Leaving the system on, or using it while
in a case or covering may cause overheating or may damage the
system.
•
•
Do not touch the connector area (A) with your hands or with metal
objects.
Do not press hard when writing on the memo area (B).
Precautions
8
•
Put both the PSP® system and the Remote Control in Hold Mode to
help prevent unintended operation.
this case, remove the UMD and turn off and unplug the system. Do not
put the UMD back in until the moisture evaporates (this may take
several hours). If the system still does not operate properly, contact the
appropriate PSP® customer service helpline which can be found within
every PSP® format software manual.
Never disassemble the system or
accessories
UMD handling
Use the PSP® system and accessories according to the instructions in this
manual. No authorisation for the analysis or modification of the system,
or the analysis and use of its circuit configurations, is provided.
Disassembling will void the system warranty and may be harmful. The
LCD screen, in particular, contains dangerous, high-voltage parts, and
the laser beam for reading UMD may cause visual impairment if exposed
directly to the eyes.
•
•
•
Do not touch the opening on the rear of the disc (recorded surface of
the disc) with your fingers.
Do not allow dust, sand, foreign objects or other types of dirt to get
on the disc.
If the UMD becomes dirty, gently wipe the exterior and recorded
surfaces of the UMD using a soft cloth. Do not use solvents or other
chemicals.
•
Do not use a UMD that is cracked or warped or has been repaired.
The UMD may break inside the PSP® system, leading to injury or
malfunction.
Using the access point
When using the PSP® system's "Scan" function to select a wireless
LAN access point, access points that are not intended for public use
may be displayed. Only connect to a personal access point that you are
authorised to use, or one that is available through a public wireless
LAN or hotspot service.
Handling and care of exterior surfaces
Follow the guidelines listed below to help avoid deterioration or
discolouration of the PSP® system:
•
•
Do not use solvents or other chemicals to clean the exterior surface.
Do not allow the system to remain in direct contact with rubber or
vinyl products for an extended period of time.
Do not use a chemically-treated cleaning cloth to wipe off the
system.
Overseas use
When travelling note any applicable wireless regulations.
•
Moisture condensation
If the PSP® system or UMD is brought directly from a cold location to
a warm one, moisture may condense on the lens inside the system or on
the UMD. Should this occur, the system may not operate properly. In
Precautions
9
Before using the analog stick
About the battery
•
•
Do not attempt to remove the analog stick from the system front, as
doing so will damage the system and may result in injury.
Battery Pack precautions
For best results, go to
(Settings)
(System Settings),
and then with the "System Information" screen displayed, rotate the
analog stick in a circular motion. This will adjust the analog stick's
range of movement.
Warnings
Do not handle a damaged or leaking Battery Pack.
Contact with the material can result in injury or burns to the eyes or
skin. Even if foreign substances are not immediately visible, chemical
changes in the material can result in injuries occurring at a later time.
Cleaning
For safety reasons, unplug the AC Adaptor or the AC Power Cord from
the electrical outlet, disconnect any other cables and remove the
Battery Pack from the system before cleaning.
If you come into contact with material from a leaking Battery
Pack, take the following actions:
•
If the material gets into the eyes, do not rub. Immediately rinse
the eyes with clean water and seek medical attention.
If the material comes into contact with the skin or clothes,
immediately rinse the affected area with clean water. Consult
your doctor if inflammation or soreness develops.
Cleaning the exterior surface and LCD screen
Wipe gently with a soft cloth.
•
Cleaning the connectors
If the headphones or remote control connectors become dirty, this
could cause noise or interruptions in sound. Wipe the connectors with
a dry, soft cloth to keep in clean condition.
Handle the Battery Pack with care.
The Battery Pack may explode or present a fire or chemical burn hazard
if it is not handled carefully.
•
Do not allow the Battery Pack to come into contact with fire or
subject it to extreme temperatures such as in direct sunlight, in a
vehicle exposed to the sun or near a heat source.
Do not cause the Battery Pack to short-circuit.
Do not disassemble or tamper with the Battery Pack.
Prevent damage to the Battery Pack. Do not carry or store the Battery
Pack with metal items such as coins or keys. If damaged, discontinue
use.
•
•
•
About the battery
10
•
USB charging uses the power supply of the USB port of the connected
device. Charge the battery by connecting the PSP® system to a device
equipped with a high-power USB port. If a low-power USB port or a USB
hub is used, the battery may not be able to be charged.
When the AC adaptor and a USB cable are connected to the PSP® system,
the battery is charged by the power supply of the AC adaptor.
Do not use or charge the PSP® system with the battery cover removed. If
the battery is suddenly removed, the battery may be dropped and damaged,
which may cause a system malfunction.
•
Do not throw or drop the Battery Pack or subject it to strong physical
shock.
•
•
Do not put heavy objects on or apply pressure to the Battery Pack.
Do not allow the Battery Pack to come into contact with liquids. If it
becomes wet, discontinue use until it is completely dry.
Keep the Battery Pack out of the reach of small children.
If the PSP® system will not be used for an extended period of time,
remove the Battery Pack and store it in a cool, dry place out of the
reach of children.
•
•
•
•
•
Use only the supplied Battery Pack or a replacement marked for use
with the correct model of the PSP® system.
Estimated battery duration
*1
Charging
Game
Approximately 3 - 6 hours
Approximately 3 - 5 hours
You can charge the battery using the AC adaptor or a USB cable (sold
separately). For details about how to charge the battery, refer to the
supplied Quick Reference manual.
*2
Video playback
*1 Based on tests conducted using the supplied Battery Pack, with the system
in single player mode, with Headphones with Remote Control in use, and
with wireless LAN not in use.
*2 Based on tests conducted using variables of system speakers versus
Headphones, volume level and screen brightness level.
Estimating the battery charge time
Charging with the AC adaptor
Charging using a USB cable
Approximately 2 hours 20 minutes
Approximately 5 hours
Hint
Battery duration may vary depending on the type of content being played or
usage conditions such as screen brightness and environmental factors. As the
battery pack ages, it will have a shorter duration.
Figures shown are for when charging a battery with no charge remaining.
Hints
•
Do not use the PSP® system with the AC Adaptor when the Battery Pack
is not inserted in the system. If the AC Adaptor is disconnected suddenly,
it may result in damage to the system.
Charge in a temperature of 10°C to 30°C. Charging may not be as effective
in other environments.
Battery Pack life
•
The Battery Pack has a limited life span. Battery duration will
decrease with repeated usage and age. When battery duration
becomes short or if the Battery Pack bulges, replace the battery
immediately.
•
•
Charging may take longer when the system is turned on during charging or
when a USB cable is used for charging.
About the battery
11
•
The Battery Pack life span varies depending on how it is stored, the
conditions of use and environmental factors, such as temperature.
Compatible media
Replacing the Battery Pack
The media types listed below can be used on the PSP® system.
Throughout this manual, the term "Memory Stick Duo™" is used to
refer to all types of Memory Stick™ media in the table below.
•
•
For safety reasons, turn off the system and remove the power cord
from the electrical outlet and disconnect any other cables before
replacing the Battery Pack.
If the system is left unused after the battery charge runs out or the
Battery Pack has been removed, the date and time settings may be
reset. If this occurs, the date and time setting screen will be displayed
the next time the PSP® system is turned on.
Type
Logo
UMD
Memory Stick Duo™ (not
MagicGate™-compatible)
Storing the Battery Pack
MagicGate™ Memory Stick
Duo™
*1
When the system will not be used for an extended period of time,
remove the Battery Pack from the system. Store the Battery Pack in a
cool, dry place out of the reach of children.
Memory Stick Duo™
*1 *2
(MagicGate™ compatible)
Memory Stick PRO Duo™
Memory Stick PRO-HG
*1 *2
*1 *2
Duo™
Memory Stick Micro™
*1 *2 *3
(M2™)
*1 Compatible with MagicGate™
*2 Compatible with high-speed data transfer over a parallel interface.
Compatible media
12
*3 To use Memory Stick Micro™ media, you must first insert it into an M2
Duo-size adaptor. If the Memory Stick Micro™ is inserted directly into
the system, it may not be able to be ejected.
File size limitation
The specification of the file system used on Memory Stick™ media
limits the size of files that can be recorded or played to less than 4 GB
per file.
Hints
•
•
•
The standard-size Memory Stick™ cannot be used with the system.
Performance of all Memory Stick™ media is not guaranteed.
If a Memory Stick Duo™ is formatted in a device other than the PSP®
system, such as a PC, it is possible that the system will not recognise it. If
MagicGate™
is a term of copyright-protection technology
developed by Sony Corporation.
this happens, go to
(System Settings)
"Format Memory Stick™"
and re-format the Memory Stick Duo™.
UMD
UMD contain a region code that is assigned to each sales region. This
system can play UMD marked with either region code "ALL", "4"
(PSP-3002 only) or "2" (PSP-3003 only).
(PSP-3002 only)
(PSP-3003 only)
Memory Stick™
Parallel data transfer (high-speed data transfer)
Parallel data transfer is a high-speed data transfer technology that
allows multiple data input/output connectors on the Memory Stick™ to
be used at the same time (parallel interface). The PSP® system supports
4-bit parallel data transfer. However, the time required for reading/
writing differs according to the media in use.
Compatible media
13
,
,
,
Some USB devices cannot be used to charge the battery.
When you connect a USB cable during gameplay, the PSP®
system does not automatically change to USB mode.
Troubleshooting
Before requesting service
If "USB Auto Connect" under
"Off", the system must be set to USB mode manually. Select
(USB Connection) under (Settings).
(System Settings) is set to
Go through this section if you experience difficulty in operating the
PSP® system. Should any problem persist, contact the appropriate
PSP® customer service helpline which can be found within every PSP®
format software manual.
The battery charge doesn't last long.
,
The charge may run out sooner depending on the storage method,
usage conditions or environment factors. For details, see "About
Power, battery and charging issues
The power does not turn on.
The Battery Pack is bulged or swollen.
If the Battery Pack bulges, replace the Battery Pack immediately.
,
,
The battery charge may have run out. Charge the battery.
Check that the Battery Pack is properly inserted.
,
Screen
The battery does not charge, or does not fully recharge.
,
,
,
When using the AC adaptor, check that the AC Adaptor or the AC
Power Cord are properly inserted in the system and the electrical
outlet.
When using the USB cable, check that the USB cable is fully
inserted into the system and the USB device and that the USB
device is turned on.
The battery may not charge efficiently or charging may take
longer depending on the usage conditions or environmental factors
during charging. For details, see "About the battery"
The screen suddenly turns dark.
,
If "Backlight Auto-Off" under
set, the LCD screen's backlight will automatically turn off if the
system is left inactive for the set amount of time.
(Power Save Settings) has been
,
If "Auto Sleep" under
system will automatically enter sleep mode if left inactive for the
set amount of time.
(Power Save Settings) has been set, the
The screen is dark and hard to see.
Use the display button on the system front to adjust the brightness.
(
,
,
,
Check that the system connectors (such as the USB connector) and
the AC adaptor or USB cable connectors are clean. If not, wipe the
connectors with a soft, dry cloth.
When using an AC adaptor, check that the correct AC Adaptor for
this product is being used.
Before requesting service
14
Black or continuously lit pixels on the screen do not
disappear.
Sound
,
LCD screens are made with highly precise technology, but in some
cases, black (dark) pixels or continuously lit pixels may appear on
the screen. This is not a system malfunction. For details, see
There is no sound.
,
Check that the volume is not set to zero. Try raising the volume.
Check that the mute setting is not on. Press the sound button on the
system front to clear the mute setting.
,
page 6).
,
When headphones or a video output cable is connected, no sound
is output from the PSP® system speakers.
The colour of the screen does not look right.
If "Theme" under (Theme Settings) is set to "Original", the
,
background colour will automatically change at the beginning of
each month.
The volume does not turn up.
,
If "AVLS" under
maximum volume level is restricted.
(Sound Settings) is set to "On", the
Video cannot be output to the TV.
,
The ear friendly Headphones supplied with PSP-1003 are
specifically designed to limit sound pressure level to a maximum
of 90dB.
,
Check that the video output cable is fully inserted into the system
and the TV.
Some TVs may not be able to output video from the PSP® system.
The PSP® system outputs in the NTSC video format. If a display
is used which does not support the NTSC video format, no picture
will be displayed. Check with the TV manufacturer for details.
,
,
,
When a video output cable is connected, the volume cannot be
changed using the PSP® system's volume + button / volume -
button. Adjust the volume on the connected device.
The headphones do not emit sound or the sound contains
noise.
When video is output to a TV, black bars are displayed on
the sides (or top and bottom) of the image.
,
Check that the headphones are fully inserted.
,
Because the size of the video image output to the TV for games or
Internet browser screens is predetermined, horizontal or vertical
black bars may be displayed at the edges of the image.
The PSP® system's internal microphone does not pick up
sound.
,
When a headset (sold separately) is connected, the PSP® system
receives sound through the headset's microphone. The internal
microphone cannot be used.
been set, the screensaver is automatically activated if no
operations are performed for a certain period of time.
Before requesting service
15
UMD
Video
The system does not recognise the UMD.
Videos do not play.
,
Slide the POWER/HOLD switch up and hold it for at least three
seconds until the POWER indicator turns off. Power will be
completely cut off. After that, turn the system back on.
,
Some types of data may not be able to be played.
The system does not recognise a video file.
,
,
Video data of types that are not compatible with the system will
not be recognised.
If the file or folder name on the Memory Stick Duo™ is changed,
or if the file or folder is moved to another location using a PC, the
system may not recognise it.
Upon starting a UMD, a message recommending an update
is displayed.
,
Update the system software. For details on updates, refer to the
Quick Reference manual supplied with the system.
Memory Stick Duo™
Music
The Memory Stick Duo™ cannot be inserted.
Music does not play.
,
Set the Memory Stick Duo™ in the proper direction when
inserting.
,
The playback methods may be limited for some music data that is
distributed through the Internet. In such cases, the data may not be
able to be played on the PSP® system.
,
Check that media of a type that can be used with the PSP® system
The system does not recognise a music file.
The system does not recognise the Memory Stick Duo™.
,
Check that the music data is saved in the correct folder on the
Memory Stick Duo™. For details, refer to the User's Guide
,
,
If Memory Stick Duo™ media is formatted using a PC, it may not
be recognised by the PSP® system. If this happens, copy any data
(
you want to keep on the PC, and then go to
"Format Memory Stick™" and re-format.
(System Settings)
,
,
Music data of types that are not compatible with the system will
not be recognised.
To play WMA format data, you must first activate "Enable WMA
Check that the Memory Stick Duo™ is properly inserted. Try
taking out the Memory Stick Duo™ and reinserting it.
Playback" under
(System Settings).
The system can't save or load data.
,
There may be a problem with the Memory Stick Duo™. Try using
another Memory Stick Duo™, if available.
Before requesting service
16
,
,
When communicating with another system in ad hoc mode, both
systems must be set to the same channel. You can check the
Photo
currently set channel under
Mode".
(Network Settings)
"Ad Hoc
Images do not display.
If a device that causes radio interference such as a microwave oven
is nearby, system communications may not work properly.
,
Depending on the image data size, certain images are not
viewable.
,
If images are edited using a PC, they may not be viewable.
The Web page won't display properly.
Some Web pages may not display properly.
,
The system does not recognise an image file.
,
Check that the data is saved in the correct folder on the Memory
Other issues
,
If the file or folder name on the Memory Stick Duo™ is changed,
or if the file or folder is moved to another location using a PC, the
system may not recognise it.
Images that are not compatible with the PSP® system will not be
recognised.
The system or AC Adaptor is warm.
,
,
During use, the system or AC Adaptor may become warm. This is
not a malfunction.
,
When the communication function is being used, the system may
become warmer than during normal use. This is not a malfunction.
Network
The system is turned on, but does not operate.
,
Check that the system is not in hold mode. If it is, slide the
POWER/HOLD switch up to clear hold mode.
A connection to the network cannot be established.
,
Check that the WLAN switch on the top of the system is turned on.
If "WLAN Power Save" under (Power Save Settings) is set to
,
"On", you may not be able to transmit data correctly.
There may be too much distance between the system and the
access point or, when in ad hoc mode, between the system and the
other player's system.
Check that the network settings are correct. Refer to the
instructions supplied with the network equipment and by your
Internet service provider to make the correct network settings.
Depending on the access point setting, you may need to enter the
system's MAC address. You can check the MAC address under
,
,
,
(System Settings)
"System Information".
Before requesting service
17
The date and time are reset.
The analog stick does not function properly.
,
If the battery is not recharged and runs out, or if the Battery Pack
is replaced, the system date and time settings may be reset. Follow
the on-screen instructions to set the time and date.
,
At a scene where the symptoms appear, move the analog stick in a
circular motion. This will help you determine the optimum
operating range.
The PSP® system is not recognised by the PC when
connected using a USB cable.
The PSP® system cannot communicate with another PSP®
system in ad hoc mode and communication is
disconnected.
,
,
,
,
Check that your PSP® system is set to USB mode. Ifit is not, select
(USB Connection) under (Settings).
Check that your Memory Stick Duo™ media is inserted into your
PSP® system.
Check that an operating system that supports USB mass storage
class is installed in the personal computer in use.
When using a USB hub or other devices, depending on the
operating environment of the PC, the Memory Stick Duo™
inserted in the system may not be recognised by the PC. Try
connecting the system directly to the PC using a USB cable.
,
If "UMD™ Cache" under
you may not be able to communicate properly.
(System Settings) is set to "On",
,
If "USB Charge" under
device may not be recognised.
(System Settings) is set to "On", the
The connected USB device is not recognised by the PSP®
system.
,
Check that the USB connector on the top of the system is clean.
Try wiping it with a soft, dry cloth.
You forgot your password.
If you restore default settings under
"Restore Default Settings", the system password will be reset to
,
(System Settings)
Note that if you restore default settings, settings you have adjusted
for options other than the system password will also be cleared.
Once cleared, these custom settings cannot be restored by the
system.
Before requesting service
18
IMPORTANT
1. If you need to claim under this Guarantee, please call your local
Customer Service helpline (listed in the PSP® current software
manual) for return instructions and other guidance.
GUARANTEE
2. Where SCEE has put this product on the market in Australia and
New Zealand, this Guarantee is valid in Australia and New Zealand,
provided:
i. the original sales receipt or invoice or other proof of purchase
(indicating the date of purchase and retailer’s name) is presented
together with the defective Product within the Guarantee period
(and has not been altered or defaced since the date of original
purchase); and
GUARANTEE FOR CONSUMERS IN
AUSTRALIA & NEW ZEALAND
Thank you for buying this Product. The term "Product" means the
PSP® system. This Guarantee does not cover any software whether or
not packaged with the Product. The system software pre-installed on
the PSP® system is licensed to you, not sold, and is for use only as part
of the PSP® system. The terms of such system software licence are at
ii. the Guarantee seal and the serial number on the Product have not
been damaged, altered, defaced or removed.
3. To avoid damage to or loss/erasure of removable data storage media
or peripherals, you must remove these before submitting the Product
for guarantee service.
4. Repair or replacement will involve installation of the latest software
or firmware updates for the Product.
Sony Computer Entertainment Europe Ltd ("SCEE") guarantees that
this Product is free from defects in material and workmanship that
result in Product failure during normal usage in accordance with the
terms set out in below and will, for a period of 1 (one) year from the
date of original purchase, repair or (at SCEE's option) replace any
component part of this Product, free of charge, where it is faulty due to
defective materials or workmanship. Replacement will be with a new
or refurbished component or unit, at SCEE's option, which is
guaranteed for the remainder of the original Guarantee Period.
5. You may not claim under this Guarantee when the Product is
damaged as a result of:
i. commercial use, accident, fair wear and tear, negligence, abuse,
or misuse (including, without limitation, failure to use this
Product for its normal purpose and/or in accordance with
instructions on proper use and maintenance, or installation or use
in a manner inconsistent with applicable local technical or safety
standards);
ii. use in conjunction with any unauthorised peripheral (including,
without limitation, game enhancement devices, adaptors and
power supply devices);
The benefits conferred by this Guarantee are in addition to other rights
and remedies which the consumer has in law in Australia and New
Zealand in respect of this Product, including rights and remedies
available under the Trade Practices Act 1974 and State and Territory
legislation in Australia and the Fair trading Act 1986 in New Zealand
and this Guarantee does not affect such rights and remedies in any way.
iii.any adaptation or adjustment to, or alteration of, the Product
carried out for any reason, and whether properly carried out or
not;
This Guarantee is given to you by Sony Computer Entertainment
Europe Ltd of 10 Great Marlborough Street, London, W1F 7LP, United
Kingdom.
GUARANTEE
19
iv. maintenance or repairs carried out other than by a SCEE
authorised service facility; or
v. use in conjunction with unauthorised software, virus infection, or
fire, flood or other natural calamity.
GUARANTEE FOR CONSUMERS IN UK &
EIRE
Thank you for buying this Product. The term "Product" means the
PSP® system. This Guarantee does not cover any software whether or
not packaged with the Product. The system software pre-installed on
the PSP® system is licensed to you, not sold, and is for use only as part
of the PSP® system. The terms of such system software licence are at
6. You may not claim under this guarantee where you are in material
breach of your system software licence
(see http://www.scei.co.jp/psp-eula).
7. To the extent permitted by applicable law, this Guarantee will be
your sole and exclusive remedy in relation to defects in this Product
and all other guarantees, warranties, terms and conditions, express
or implied by statute or otherwise, in respect of this Product are
excluded and neither SCEE nor any other Sony entity, or their
suppliers or authorised service facilities, will be liable for any
special, incidental, indirect or consequential loss or damage.
Sony Computer Entertainment Europe Ltd ("SCEE") guarantees that
this Product is free from defects in material and workmanship that
result in Product failure during normal usage in accordance with the
terms set out in below and will, for a period of 1 (one) year from the
date of original purchase, repair or (at SCEE's option) replace any
component part of this Product, free of charge, where it is faulty due to
defective materials or workmanship. Replacement will be with a new
or refurbished component or unit, at SCEE's option, which is
guaranteed for the remainder of the original Guarantee Period.
If this Product needs any repair which is not covered by this Guarantee,
please call your local Customer Service helpline for advice. If your
home country is not one of those listed, please contact your retailer.
This Guarantee is in addition to your statutory consumer rights (under
applicable law) and does not affect them in any way.
This Guarantee is given to you by Sony Computer Entertainment
Europe Ltd of 10 Great Marlborough
Street, London, W1F 7LP, United Kingdom.
GUARANTEE
20
IMPORTANT
1. If you need to claim under this Guarantee, please call your local
Customer Service helpline (listed in the PSP® current software
manual) for return instructions and other guidance.
2. Where SCEE has put this product on the market in the European
Economic Area or Switzerland, this Guarantee is valid in all EU
Member States plus Switzerland, Norway, Iceland and
Liechtenstein, provided:
i. the original sales receipt or invoice or other proof of purchase
(indicating the date of purchase and retailer's name) is presented
together with the defective Product within the Guarantee period
(and has not been altered or defaced since the date of original
purchase); and
ii. the Guarantee seal and the serial number on the Product have not
been damaged, altered, defaced or removed.
3. To avoid damage to or loss/erasure of removable data storage media
or peripherals, you must remove these before submitting the Product
for guarantee service.
4. Repair or replacement will involve installation of the latest software
or firmware updates for the Product.
5. You may not claim under this Guarantee when the Product is
damaged as a result of:
iii.any adaptation or adjustment to, or alteration of, the Product
carried out for any reason, and whether properly carried out or
not;
iv. maintenance or repairs carried out other than by a SCEE
authorised service facility; or
v. use in conjunction with unauthorised software, virus infection, or
fire, flood or other natural calamity.
6. You may not claim under this guarantee where you are in material
breach of your system software licence
(see http://www.scei.co.jp/psp-eula).
7. To the extent permitted by applicable law, this Guarantee will be
your sole and exclusive remedy in relation to defects in this Product
and all other guarantees, warranties, terms and conditions, express
or implied by statute or otherwise, in respect of this Product are
excluded and neither SCEE nor any other Sony entity, or their
suppliers or authorised service facilities, will be liable for any
special, incidental, indirect or consequential loss or damage.
If this Product needs any repair which is not covered by this Guarantee,
please call your local Customer Service helpline for advice. If your
home country is not one of those listed, please contact your retailer.
i. commercial use, accident, fair wear and tear, negligence, abuse,
or misuse (including, without limitation, failure to use this
Product for its normal purpose and/or in accordance with
instructions on proper use and maintenance, or installation or use
in a manner inconsistent with applicable local technical or safety
standards);
ii. use in conjunction with any unauthorised peripheral (including,
without limitation, game enhancement devices, adaptors and
power supply devices);
GUARANTEE
21
Additional information
Weight
Approx. 189 g (including Battery Pack)
5°C - 35°C
Operating environment
temperature
Specifications
Video:
Design and specifications are subject to change without notice.
H.264/MPEG-4 AVC Main Profile
Level 3
Music:
H.264/MPEG-4 AVC Main Profile
Level 3, Linear PCM, ATRAC3plus™
UMD
Compatible
codecs
PSP® (PlayStation®Portable) system
4.3 inches / 10.9 cm (16:9) full-transparent
type, TFT drive
Approximately 16,770,000 colours
displayed
LCD screen
Memory
Stick™
For details, refer to the User's Guide
(
Sound
Stereo speakers
UMD laser
Internal disc drive
Read-only UMD drive
Wave length
Power
655 - 665 nm
DC IN 5V connector
Video out/headset connector
Hi-Speed USB (USB 2.0 compliant)
DC OUT connector
Max. 0.28 mW
Interface
Type
Semiconductor, continuous
Memory Stick Duo™ slot
Wireless LAN (IEEE 802.11b)
Microphone
Wireless LAN
AC Adaptor: DC 5.0 V
Rechargeable Battery Pack: Lithium-Ion
rechargeable Battery Pack
Standard
IEEE 802.11b
Power source
Modulation format
DS-SS (IEEE 802.11b compliant)
Maximum power
consumption
Approx. 6 W (when charging)
Approx. 169.4 × 18.6 × 71.4 mm (width ×
height × depth) (excludes largest projection)
External dimensions
Specifications
22
AC Adaptor*
Software
Input
AC 100-240 V, 50/60 Hz
DC 5 V, Max. 1500 mA
Software developed by the NetBSD Foundation, Inc. and its
contributors is used for the communication functions of this product.
For more information, see
Output
Approx. 46 × 22 × 61 mm (width × height ×
depth) (excludes largest projection) (PSP-
3002)
Approx. 51 × 61 × 54 mm (width × height ×
depth) (excludes largest projection) (PSP-
3003)
This product adopts S3TC texture compression technology under
licence from S3 Graphics, Co., Ltd.
External dimensions
This product includes RSA BSAFE® Cryptographic software from
RSA Security Inc.
RSA, BSAFE are either registered trademarks or trademarks of RSA
Security Inc. in the United States and/or other countries.
RSA Security Inc. All rights reserved.
Approx. 57g (PSP-3002)
Approx. 66g (PSP-3003)
Weight
*
The PSP-3003 model comes with a combined AC Adaptor and AC Power
Cord.
U.S. and foreign patents licenced from Dolby Laboratories.
MPEG Layer-3 audio coding technology and patents licenced from
Fraunhofer IIS and Thomson.
Battery Pack
Battery type
Voltage
Lithium-ion rechargeable battery
DC 3.6 V
This product contains
ACCESS Co., Ltd.
Copyright © 1996-2008 ACCESS Co., Ltd.
is a trademark or registered trademark of ACCESS Co.,
Internet browser software of
Capacity
1200 mAh
Ltd. in Japan and other countries.
This product is protected by certain intellectual property rights of
Microsoft Corporation. Use or distribution of such technology outside
of this product is prohibited without a licence from Microsoft or an
authorised Microsoft subsidiary.
Specifications
23
The PSP® system's RSS Channel feature uses RSS (Really Simple
Syndication) 2.0 technology. For details on RSS 2.0, visit
THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT
WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR
OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE.
Contains Macromedia® Flash® Player technology by Adobe
Copyright © 1995-2008 Adobe Systems Incorporated. All rights
reserved. Flash, Macromedia, and Macromedia Flash are either
trademarks or registered trademarks of Adobe Systems Incorporated in
the United States and/or other countries.
IN NO EVENT SHALL SAM LEFFLER OR SILICON
GRAPHICS BE LIABLE FOR ANY SPECIAL, INCIDENTAL,
INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY
KIND, OR ANY DAMAGES WHATSOEVER RESULTING
FROM LOSS OF USE, DATA OR PROFITS, WHETHER OR
NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND
ON ANY THEORY OF LIABILITY, ARISING OUT OF OR IN
CONNECTION WITH THE USE OR PERFORMANCE OF
THIS SOFTWARE.
Portions of the PSP® system software require the following notices
(these statements do not affect the limited warranty offered on the
PSP® system or UMD software):
This software is based in part on the work of the Independent
JPEG Group.
Copyright © 1988-1997 Sam Leffler
Copyright © 1991-1997 Silicon Graphics, Inc.
Trademarks
"
", "PlayStation", "
" and "
" are
Permission to use, copy, modify, distribute, and sell this software
and its documentation for any purpose is hereby granted without
fee, provided that (i) the above copyright notices and this
permission notice appear in all copies of the software and related
documentation, and (ii) the names of Sam Leffler and Silicon
Graphics may not be used in any advertising or publicity relating
to the software without the specific, prior written permission of
Sam Leffler and Silicon Graphics.
registered trademarks, and "UMD" is a trademark of Sony Computer
Entertainment Inc.
"
" and "XMB" are trademarks of Sony Corporation and Sony
Computer Entertainment Inc.
"SONY" and " " are registered trademarks of Sony Corporation.
Also, "Memory Stick Duo", "Memory Stick PRO Duo", "Memory
Stick PRO-HG Duo", "Memory Stick Micro", "M2", "Memory Stick",
"
", "MagicGate", and "ATRAC" are trademarks of the same
company.
Specifications
24
ATOK is a registered trademark of JUSTSYSTEM CORP. in Japan
and other countries.
Windows and Windows Media are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other
countries.
Mac OS is a trademark of Apple, Inc.
All other trademarks are the properties of their respective owners.
About national export control
This product may fall within the scope of national export control
legislation. You must comply fully with the requirements of such
legislation and of all other applicable laws of any jurisdiction in
relation to this product.
Notice about U.S. Export Administration
Regulations
This product contains software that is subject to certain restrictions
under the U.S. Export Administration Regulations, and may not be
exported or re-exported to U.S. embargoed destinations. In addition
this product may not be exported or re-exported to persons and entities
prohibited by the U.S. Export Administration Regulations.
Specifications
25
|