Sony Electronics Inc.
1 Sony Drive
Park Ridge, NJ 07656
Outdoor and Indoor Dome Housings
Installation and Operation Instructions for the following models:
BRCSDP12
(1) Housing
(1) Supplied Parts
(1) Power connector (Heather/blower)
(1) Toolhead driver
(1) Operation Instruction Manual
INSTALLING THE CAMERA
WIRING
1
Install the Sony BRC300 pan/tilt onto the quick release
bracket using the (4) screws provided with the camera
(Figure 4).
CHART A WIRING COLOR CODE
POWER AND CONTROL INPUTS
POWER
1
2
3
4
Camera Power (12 VDC)
Camera Power (12 VDC)
Heater & Blower Power (24 VAC) Yellow
Heater & Blower Power (24 VAC) Green
Red
Orange
NOTE: Failure to provide power to heater and blower will
void the warranties on both the housing and camera.
OPTIONAL
1
2
3
4
Alarm 1
Alarm 2
Alarm 3
Common
Blue
Violet
Gray
White
Figure 4
2
Place the Sony BRC300 pan/tilt and quick release bracket
in the housing, sliding the three open screw slots over the
screws in the housing. Slide the bracket forward, then tighten
the captive screw on the bracket (Figures 5, 6, and 7).
CHART B POWER AND CONTROL OUTPUTS
CAMERA POWER
Camera Power (12 VDC)
Camera Power (12 VDC)
1
2
Red
Orange
Connect the power plug to the camera per Sony SNCRZ30N
instructions.
OPTIONAL
1
2
3
4
Alarm 1
Alarm 2
Alarm 3
Common
Blue
Violet
Gray
White
Figure 5
24k VAC Wiring Distances
The following are the recommended maximum distances for 24 VAC
with a 10% voltage drop (10% is generally the maximum allowable
voltage drop for AC powered devices).
Wire Gauge
Total vA
consumed
50
20
18
16
14
12
10
22
56
90 143 228 362 576
35
Figure 6
Figure 7
© 2003 by Sony Corporation
10/13/04
2
IMPORTANT SAFEGUARDS
SAFETY PRECAUTIONS
1
2
3
Read Instructions - All the safety and operating instructions
should be read before the unit is operated.
CAUTION
Retain Instructions - The safety and operating instructions
should be retained for future reference.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
Heed Warnings - All warnings on the unit and in the operat-
ing instructions should be adhered to.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
4
5
6
Follow Instructions - All operating and user instructions
should be followed.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
Electrical Connections - Only a qualified electrician should
make electrical connections..
The lightning flash with an arrowhead symbol, within
an equilateral triangle, is intended to alert the user to the
presence of non-insulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
Attachments - Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Cable Runs - All cable runs must be within permissible
distance
7
8
Mounting - This unit must be properly and securely
mounted to a supporting structure capable of sustaining the
weight of the unit. Accordingly:
The exclamation point within an equilateral triangle is
intended to alert the user to presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
!
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local
codes.
UNPACKING
c. Care should be exercised to select suitable hardware to
install the unit, taking into account both the composition
of the mounting surface and the weight of the unit. Be
sure to periodically examine the unit and the supporting
structure to make sure that the integrity of the in stalla-
tion is intact. Failure to comply with the foregoing
could result in the unit separating from the support
structure and falling, with resultant damages or injury to
anyone or anything struck by the falling unit.
Unpack carefully. Electronic components can be damaged if improperly
handled or dropped. If an item appears to have been damaged in ship-
ment, replace it properly in its carton and notify the shipper.
Be sure to save:
1
The shipping carton and packaging material. They are the safest
material in which to make future shipments of the equipment.
2
These Installation and Operating Instructions.
SERVICE
If technical support or service is needed, contact Sony at the following
number:
TECHNICAL SUPPORT
8:15AM to 7:30PM (Eastern Time)
1-800-883-6817
© 2003 by Sony Corporation
10/13/04
5
|