Sony MP3 Player Accessories RM V310 User Manual

4 Enter the component’s code number.  
For example, if you’re entering the code  
for a Philips VCR, you would press  
.
1 While pressing the SET button, press the POWER button.  
2 Press the VCR, CBL, SAT, AMP, CD, or DVD button.  
3 Press and release the x (stop) button.  
Notes  
Notes  
2-674-862-11(1)  
Operating a DVR (Digital video recorder)  
Operating a digital satellite receiver  
Operating a CD player  
0
3
5
If you are using more than one receiver (or amplifier) and have set  
it on the VCR, CBL, SAT, CD or DVD button, when selecting these  
buttons you cannot control the volume of the receiver (or  
amplifier) of the AMP button.  
Even if you try to program more than four operations and press the  
corresponding buttons in step 2 above, only the first four buttons  
that were pressed will be programmed.  
Remote Button Descriptions  
2 To switch the output of the SAT qh (*2REPLAY)  
3 To select the track number. 0  
selects track 10. To select track  
numbers above 10, see the  
descriptions on the • (DOT)  
button above.  
4 To select numbers 10 and  
above. For example, to select  
track 15, press • (DOT) and  
then press 5.  
qg CH+: To select the next track.  
CH: To select the previous  
track.  
qh To select next disc.  
qj To clear the setting.  
wa N: To play.  
2 To switch the output of the  
digital satellite receiver to the  
TV. (When you connect a TV  
cable or antenna to the receiver,  
the output switches between a  
TV and SAT program.)  
3, 4 and qd  
qg Channel up: +  
Your Code Number  
receiver to the TV.  
To replay.  
Channel down: –  
General  
(When connecting a TV cable or  
antenna to the receiver, the  
output switches between a TV  
and SAT program.)  
Or to go into REC/REVIEW  
mode during play. (After about  
5-second rewind, replay  
begins.)  
RM-V310  
To page through the guide  
when a program guide is  
displayed.  
If you try to program only one operation on a macro key, the  
setting operation will be rejected.  
You can program the Channel Macro function for up to three  
components only. To program for the fourth component, first clear  
all macro keys for a component.  
POWER  
SET  
Remote Commander  
1 To set up the Commander,  
4 Press and release one of the following buttons;  
to assign a VCR  
5 Press and release the ENT button to store  
the code number in the Commander’s  
memory.  
TV/VIDEO  
ENT  
TV  
DVD  
CD  
SAT  
If you change the setting of the AMP button to a component other  
than a receiver or amplifier, the volume control setting of video  
components will return to “TV” even if you have changed the  
factory preset volume control. In this case, you will not be able to  
control the volume from audio components other than a receiver or  
amplifier.  
press SET while pressing  
POWER.  
CBL  
VCR  
AMP  
AUX  
VIDEO1  
VIDEO2  
Operating Instructions  
to assign a DAV (DVD/receiver combo)  
to assign a digital satellite receiver, a digital cable box or a  
digital video recorder  
qh To tune to the last tuned  
station.  
qj To bring up the Station Index.  
qk To call up the MENU display.  
ql To scroll through the Master  
Guide.  
6 *1Volume up: +  
1
2
3
(*2THUMBS+)  
qk To call up the MENU display.  
m: To rewind.  
M: To fast-forward.  
TUNER  
CD  
TAPE  
4
5
6
6 Go to “Step 2: Checking if the Code Number Works” to finish  
setting up.  
Volume down: –  
Manual de instrucciones (parte posterior)  
MD  
TV  
PHONO  
To select the desired recorded  
program.  
(It is necessary to have  
recorded the desired program.)  
(*2EPG)  
7
8
9
To change the channel. For  
example, to change to channel  
5, press 0 and 5 (or press 5 and  
ENT).  
DVD  
7 *1To mute the volume on TV or  
receiver (amplifier).  
To access to all aspects of the  
service.  
x:  
X:  
To stop.  
To pause.  
ENT  
0
to assign a receiver  
To change or clear the program  
DIGITAL  
VOL  
CH  
© 2006 Sony Corporation Printed in China  
/ANALOG  
8 To switch the display of the CD  
player to on/off.  
qd To enter the setting.  
to assign a CD player  
When you want to change the setting or if you are no longer using  
that programmed operation, follow the procedure below to  
overwrite or clear the program.  
qa To turn on and off the power of  
the selected component.  
qs Component select buttons. To  
switch to the operations of each  
component, press the button on  
which that component is  
assigned.  
Step 2: Checking if the Code Number Works  
TWIN VIEW  
SLEEP  
ql To move the cursor upward,  
downward, to the left, or to the  
right.  
to assign a tape deck  
To reset to factory preset volume control  
In step 3 above, press VOL– instead.  
3 and qd  
5 To use the “FAVORITE”  
function.  
9 To bring up the Master Guide.  
q; To exit the mode.  
ql OK: To select the channel  
that's highlighted. To  
bring up the Station  
to assign an MD deck  
1 Power on the component you want to set up.  
INFO  
To change the channel. For  
example, to change to channel  
5, press 0 and 5 (or press 5 and  
ENT).  
MUTING  
GUIDE  
RECALL  
to assign a TV  
MENU  
2 Aim the Remote Commander at the component and press a button  
to check if that button works.  
For example, press the POWER button to see if it works on your  
component .  
ql OK: To bring up the Station  
Index when a program  
guide is not displayed.  
To select the channel  
that is highlighted.  
English  
1 Hold down the macro key that you want to change or clear.  
to assign an analog cable box  
to assign a DVD  
Operating an MD deck  
Index when a program  
guide is not displayed.  
OK  
2 After waiting for about three seconds, press the new sequence of  
buttons, or, to clear the program, press and release  
press and release ENT.  
3 To select the track number. 0  
selects track 10. To select track  
numbers above 10, see the  
descriptions on the • (DOT)  
button above.  
4 To select numbers 10 and  
above. For example, to select  
track 15, press • (DOT) and  
then press 5.  
8 To change the display mode or  
turn the display on/off.  
qd To enter the setting.  
qg CH+: To select the next track.  
CH: To select the previous  
track.  
qh To select next disc.  
qj To clear the setting.  
wa N: To play.  
EXIT  
TOOLS  
Operating a Component  
, and then  
Installing the Batteries  
8 To turn on the display.  
5 Press and release the ENT button.  
For the customers in the U.S.A.  
WARNING  
(*2THUMBS–)  
Before replacing the batteries, have new ones ready beforehand.  
*1These buttons control the volume  
of either TV or receiver  
(amplifier). See “Controlling the  
Volume of Video Components  
Connected to an Audio System”  
for details.  
TV  
DVD  
CD  
SAT  
1 Press the button of the desired  
component on the Commander.  
6 Enter the component’s code number by following steps 2 to 6 of  
“Entering the Code Number”, or steps 1 to 7 of “Searching for the  
Correct Code.”  
3 Check that the other buttons of the Commander is operating the  
corresponding functions of the component.  
m: To rewind.  
M: To fast-forward.  
To select the desired recorded  
program.  
wa N: To play.  
Operating a DVD  
3 Release the macro key.  
Slide open the battery compartment and insert two size AA (R6)  
batteries (not supplied).  
Be sure to line up the + and – on the batteries with the + and – on the  
battery compartment.  
m: To rewind.  
CBL  
VCR  
AMP  
2 To change the sound.  
3 Number buttons : To set items  
selected from the screen.  
4 To select numbers 10 and  
above. For example, to select  
track 15, press PIP and then  
press 5.  
8 To show the current play status  
on the screen.  
9 To clear the selected characters  
from the screen.  
This equipment has been tested and found to comply with the limits  
for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy and, if not  
qh To display the title menu.  
qj To switch the subtitle.  
qk To display the DVD menu.  
ql To move the cursor upward,  
downward, to the left, or to the  
right.  
ql OK: To execute items  
selected from the screen.  
wa N: To play.  
x:  
X:  
To stop.  
To pause.  
(It is necessary to have  
recorded the desired program.)  
9 To bring up Master Guide.  
(*2Live TV)  
To bring up Master Guide.  
q; To clear the setting.  
To exit the setting menu.  
qf (*2LIST)  
M: To fast-forward.  
zREC:To record, press N  
while pressing zREC.  
First release N, then  
release zREC. To stop  
recording, perform the  
same procedure.  
Note  
2 Point the Commander directly at the  
component.  
Be sure to wait for about three seconds in step 2 above. While you  
are holding down the macro key and waiting, the programmed  
signals are transmitted; therefore, if you are aiming the Commander  
at your component, the programmed operations may be performed  
before you go on with the procedure.  
You can write down the code number on the label inside the  
battery compartment lid.  
zREC:To record, press N  
while pressing zREC./  
First release N, then  
release zREC.  
3 Press the button for the function you want to use.  
Controlling the Volume of Video  
Components Connected to an Audio  
System  
The Commander is factory preset based on the assumption that you  
hear the sound of your video components from your TV’s speakers,  
and that you hear the sound of your audio components from the  
loudspeakers connected to your receiver (or amplifier).  
1
2
See “Remote Button Descriptions” for complete descriptions of the  
buttons on the Commander.  
If the Commander Doesn’t Seem to Be Working...  
• First, try repeating these setup procedures using the other codes  
listed for your component (see the supplied “Component code  
numbers”).  
• If – after trying all the codes listed for your component – you still  
cannot get the Commander to work properly, try the search  
method described in “Searching for the Correct Code.”  
installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is  
no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Operating a TV  
qh To operate JUMP, FLASHBACK  
or CHANNEL RETURN function  
on the TV depending on the  
setting of the TV's  
2 To change the input mode.  
3, 4 and qd  
Notes on Using the Remote Commander  
Basically, use this Commander in the same way as the Commanders  
supplied with your components.  
Using this Commander will not increase the functions of your  
components. The functions of the Commander are limited to the  
functions of the components themselves. For example, if your TV  
does not have a MUTING function, the MUTING button on this  
Commander will not function with your TV.  
Some functions of the component may not work with this  
Commander.  
If your cable box can control volume, be sure to set its volume  
switch to a medium position. If the volume on the cable box is  
turned down completely, you will not be able to adjust your TV’s  
volume with the Commander.  
x:  
To stop.  
To call up the title of the  
recorded program.  
X:  
To pause.  
To change the channel. For  
example, to change to channel  
5, press 0 and 5 (or press 5 and  
ENT).  
m: To rewind.  
M: To fast-forward.  
x:  
X:  
zREC:To record, press N  
while pressing zREC.  
First release N, then  
release zREC.  
Troubleshooting  
qg CH+: Channel up .  
manufacturer.  
qd To enter the setting. To set  
items selected from the screen.  
qg CH+: To proceed to the next  
location or song.  
If you have problems setting up or using the Commander:  
• When setting up the Commander, carefully go through the procedures  
described in “Setting the Code.” If the code that’s listed first for your  
component doesn’t work, try all the codes for your component - in the order  
in which they’re listed. If all the codes fail to work (or if your component is  
not listed in this manual), try using the procedures in “Searching for the  
Correct Code.”  
(*2PAGE+) Page up.  
To stop.  
To pause.  
Operating a tape deck  
qj To operate SLEEP function on  
the TV. (Works only for a TV  
with the SLEEP function.)  
qk To call up the MENU display.  
ql To move the cursor upward,  
downward, to the left, or to the  
right, or to enter the selection.  
CH: Channel down.  
(*2PAGE–) Page down.  
4, and wa  
0, qd, ql and w;  
8 To display the current channel  
on TV.  
qf To operate the Picture-in-  
Picture function. Press each  
button or combination of  
buttons as described in the  
table below.  
When to replace the batteries  
Factory Setting:  
Tape operation buttons.  
For dual cassette decks,  
operation buttons for Deck A  
(for Sony-brand dual cassette  
deck, buttons for Deck B).  
• (DOT):  
Operation buttons for Deck B  
(for Sony-brand dual cassette  
deck, buttons for Deck A).  
ENT: To reverse.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from  
that to which the receiver is connected.  
Under normal conditions, batteries will last up to six months. If the  
Commander does not operate properly, the batteries might be worn  
out. Replace the batteries with new ones.  
Searching for the Correct Code  
If you’ve tried all the code numbers listed for your component and  
you still cannot get the Commander to work (or if your component is  
not listed in the “Component code numbers” tables), try these steps.  
Channel up.  
Button  
Controls the volume of  
*2 This key corresponds to Tivo service or the replay service. Refer to its  
instruction manual for details.  
CH: To proceed to the  
previous location or  
Consult the dealer or an experienced radio/TV technician for help.  
You are cautioned that any changes or modifications not expressly  
approved in this manual could void your authority to operate this  
equipment.  
TV  
TV  
• Check that you’re aiming the Commander directly at the component, and that  
there are no obstructions between the Commander and the component.  
• Make sure the batteries you’re using are not worn out, and that they’re  
inserted correctly.  
• Check that the button of the TV, VCR, CBL, SAT, AMP, CD or DVD is pressed  
to choose your desired component.  
• Check that the component has infrared remote capability. For example, if  
your component didn’t come with a remote commander, it probably isn’t  
capable of being controlled by a remote commander.  
• If your video components are connected to an audio system, make sure  
you’ve set up the Commander as described in “Controlling the Volume of  
Video Components Connected to an Audio System.”  
:
To play.  
song. Channel down.  
Notes  
VCR*, CBL*, SAT*, DVD*  
TV  
:
:
To rewind.  
To fast-forward.  
To stop.  
• Replace both batteries with new ones.  
• Do not take more than 20 minutes to replace the batteries;  
otherwise, your setting of the code numbers will be erased.  
To reverse.  
1 Power on the component you want to set up. Insert a tape or disc  
if necessary.  
Operating an analog cable box  
qg CH+: Channel up.  
CH: Channel down.  
AMP  
Receiver (or amplifier)  
Operating a receiver/amplifier  
N: To play.  
:
3 and qd  
To change the channel. For  
qh To operate JUMP, FLASHBACK  
or CHANNEL RETURN function  
on the TV depending on the  
setting of the TV's  
CD*  
Receiver (or amplifier) on the AMP  
button  
m: To rewind.  
EXIT: To record, press  
while pressing MENU.  
First release , and then  
release MENU.  
2 To switch input source by each  
pressing.  
3 To select the input source:  
1 selects VIDEO 1  
2 selects VIDEO 2  
3 selects AUX  
qg Presetting frequency up: +,  
down: –  
2 While pressing the SET button, press the POWER button.  
M: To fast-forward.  
zREC:To record, press N  
while pressing zREC.  
First release N, then  
release zREC.  
When setting the component code of a TV to “088” or “089”  
(codes for a Sony TV)  
example, to change to channel  
5, press 0 and 5 (or press 5 and  
ENT).  
Notes on Batteries  
Setting Up the Remote Commander  
3 Press the button of the component on the Commander that you  
want to set up.  
Tuning frequency up: +,  
down: –  
qh To shift band (FM/AM).  
wa Work as N, M, m, x, X  
buttons of the CD player.  
(When a CD player is set up on  
the CD button.)  
* If you assign an audio component on the VCR, CBL, SAT, CD or DVD button,  
you can control the volume of the receiver (or amplifier) on the AMP button.  
If you assign video components on these buttons, you can control the volume  
of the TV.  
• Do not mix old batteries with new ones or mix different types of  
batteries together.  
• If the electrolyte inside the battery should leak, wipe the  
contaminated area of the battery compartment with a cloth and  
replace the old batteries with new ones. To prevent the electrolyte  
from leaking, remove the batteries when you plan not to use the  
Commander for a long period of time.  
Setting a channel with a single button  
(Channel Macro function)  
manufacturer.  
TOOLS:  
wa To select TV input source.  
m: VIDEO 1  
5 To switch between digital  
broadcast and analog broadcast.  
q; EXIT  
qf TWIN VIEW  
w; OPTION  
About Presetting the Commander  
qg CH+: Channel up.  
CH: Channel down.  
4 Press and release the CH+ button. Then press and release the  
POWER button.  
To pause.  
The Commander is preset at the factory to operate Sony brand  
components.  
x:  
X:  
To stop.  
To pause  
qh To select Deck A or Deck B  
(dual cassette deck only).  
N: VIDEO 2  
4 selects TUNER  
5 selects CD  
6 selects TAPE  
7 selects MD  
8 selects TV  
You can program the Channel Macro function on any of the buttons  
listed below (macro keys).  
• Should any problem persist, reset the Commander to the factory setting by  
pressing the POWER, TV/VIDEO and VOL– buttons simultaneously.  
M: VIDEO 3  
zREC:VIDEO 4  
Notes  
Thus you can control the volume of your TV or receiver (or  
amplifier) while operating a video or audio component without first  
having to press the TV or AMP button. For example, to control the  
volume for your VCR channels, you don’t need to press the TV  
button first.  
However, if your video components are connected to an audio  
system, you probably hear your TV’s or VCR’s sound from the  
loudspeakers connected to your receiver (or amplifier), not from  
your TV speakers. In this case, you need to change the factory setting  
so that you can control the volume of your video components  
without first having to switch to the receiver (or amplifier).  
To change the factory setting for the volume control, follow the  
procedures below.  
5 Repeat step 4 until the correct code number is found.  
Each time you press the CH+ button and then the POWER button,  
a new code number will be transmitted.  
Keep trying until your component operates by receiving the  
transmitted signal from the Commander (e.g., the power turns off,  
the CH+ function works, playback starts, etc.). Be patient as you  
do this; it may take about 100 tries until the correct code number is  
located.  
If you’re using the Commander with a Sony component, you won’t  
need to preset the Commander before you start using it.  
To set up the Commander to use with other (non-Sony)  
manufacturers’ components, or to use with a component that is not  
preset at the factory, you’ll need to follow the instructions in this  
manual to preset the Commander with the correct code number for  
your components. (See the supplied “Component code numbers”  
also.)  
• There may be cases you may turn on/off the cable box by pressing the CH+ or  
CH– buttons on the Commander.  
If your tape deck’s commander has  
one set of tape operating buttons, and  
has an A/B button for the deck  
selection, use the RECALL button to  
select Deck A or Deck B.  
For example, instead of pressing  
,
, and then the ENT button  
x:  
X:  
VIDEO 5  
VIDEO 6  
to change the TV channel, you can perform these operations by  
• If your cable box can control volume, be sure to set its volume control to a  
medium position. If the volume on the cable box is turned down completely,  
you will not be able to adjust your TV’s volume with the Commander.  
For the customers in the U.S.A.  
Customer Support Information  
If – after you’ve read through this manual – you still cannot get the  
Remote Commander to work properly, call the Sony Customer  
Support Helpline at 1-800-822-2217.  
pressing only the N button.  
9 selects PHONO  
0 selects DVD  
PIP operations  
Setting the Code  
The macro keys are:  
N, m, M, x, X, and zREC.  
(During TV, analog cable box, digital cable box, digital satellite  
receiver or digital video recorder operations only.)  
Press  
To  
Follow the steps 1 and 2 below for each component you plan to use  
with the Commander.  
TWIN VIEW  
GUIDE  
m or M  
zREC  
x
Turn on/off the “window” picture.  
Operating a digital cable box  
DAV (DVD/Receiver combo)  
Turn off the “window” picture.  
Specifications  
6 When the correct code is found, press the ENT button to store the  
code number in the Commander’s memory.  
Change the TV channel in the “window” picture.  
Change the input mode of the “window” picture.  
Move the location of the “window” picture.  
Swap the “main” picture and the “window” picture.  
Freeze the “window” picture.  
2 To switch the output of the SAT  
receiver to the TV.  
qk To call up the MENU display.  
ql To move the cursor upward,  
downward, to the left, or to the  
right.  
ql OK: To bring up the Station  
Index when a program  
guide is not displayed.  
To select the channel  
that is highlighted.  
wa *3N: To play.  
*3m: To rewind.  
*3M: To fast-forward.  
*3zREC:  
2 To change the input mode.  
3 Number buttons: To set items  
selected on the screen.  
4 To select numbers 10 and  
above.  
8 To show the current play status  
on the screen.  
qj To switch the subtitle.  
qk To call up the MENU.  
ql To move the cursor upward,  
downward, to the left, or to the  
right.  
OK: To enter the selection of  
the MENU display.  
wa N: To play.  
Step 1: Entering the Code Number  
Component that can be preset Button  
Factory setting  
Sony TV  
The series of operations that can be programmed must be consisted  
of two to four sequential pressings of  
button.  
Operable distance  
Approx. 7 m (23 ft) (varies depending of the  
component of each manufacturer)  
Power requirements Two size AA (R6) batteries (not supplied)  
to  
buttons or ENT  
(When connecting a TV cable or  
antenna to the receiver, the  
output switches between a TV  
and SAT program.)  
TV  
TV  
1 See the supplied “Component code numbers”, and find the three-  
digit code number for the desired component.  
If more than one code number is listed, use the number that’s  
listed first to complete the steps below.  
For example, if you’re setting up a Philips’ VCR, you would use  
the code number 035.  
7 Check that the Commander is operating the other functions of  
your component by pressing the corresponding buttons on the  
Commander. If they seem to be working properly, you’re done  
setting up the Commander.  
Video cassette recorder/Analog  
cable box/Digital cable box/Digital  
satellite receiver/Receiver/CD  
player/Tape deck/MD deck/DVD/  
TV/VCR/Digital video recorder/  
DAV (DVD/Receiver combo)  
VCR  
CBL  
AMP  
CD  
Sony VHS VCR  
analog cable box  
Sony receiver  
Sony CD player  
N
Battery life  
Dimensions  
Mass  
Approx. 1 year (varies depending on frequency of  
button use - up to approx. 300 times per day.)  
Approx. 53 × 220 × 29 mm (w/h/d)  
Note  
X
Note  
The Channel Macro function may not work correctly for some  
components.  
3 and qd  
This feature is effective only when a receiver (or amplifier) is set up  
on the AMP button. You cannot control the volume of a receiver (or  
amplifier) set up on VCR, CBL, SAT, CD or DVD button while  
operating a component of another button.  
(2 1/8 × 8 3/4 × 1 3/16 in.)  
To change the channel  
If the component does not operate properly, repeat steps 1 to 6 and  
search for another code.  
9 To change the sound.  
qd To enter the setting.  
qg CH+: To proceed to the  
previous location or  
Note  
Approx. 132 g (4.6 oz.) (not including batteries)  
(for example, to change to  
channel 5, press 0 and 5, or  
press 5 and ENT).  
m: To rewind.  
M: To fast-forward.  
zREC*:  
If you have programmed the Channel Macro function for TV operation, the  
button used as a macro key cannot be used for PIP operation.  
To program a series of operations  
If your component isn’t listed, see “Searching for the Correct  
Code.”  
SAT  
Sony digital  
Design and specifications are subject to change without notice.  
If you still cannot get the Commander to work properly, see  
“Troubleshooting.”  
1 Press the desired component select button.  
(You can select “TV”, “analog cable box”, “digital cable box”  
“digital satellite receiver” or “digital video recorder” only.)  
satellite receiver  
SET  
POWER  
8 To turn on the display.  
9 To call up the title bar and  
toggle the title bar on/off in  
CABLE mode.  
2 While pressing the SET button, press the  
song.  
To record.  
DVD  
Sony DVD player  
POWER button.  
CH: To proceed to the next  
location or song.  
x:  
X:  
To stop.  
Operating a VCR  
The CE mark on the unit is valid only for products  
marketed in the European Union.  
Changing the Factory Setting for the  
Volume Control  
To record, press N  
while pressing  
To pause.  
TV  
DVD  
CD  
SAT  
3 Press the button of the component that  
2 While pressing the desired macro key, press the buttons required  
for the operations in sequence.  
For example, to program  
hold down N first, press  
release N.  
2 To switch the antenna output.  
8 To expose the on-screen  
display.  
wa N: To play.  
x: To stop.  
Notes  
Changing the Component Type on the VCR,  
CBL, SAT, AMP, CD and DVD buttons  
At the factory, “video cassette recorder” is assigned on the VCR  
button, “digital satellite receiver” on the SAT button, “analog cable  
box” on the CBL button, “receiver” on the AMP button, “CD player”  
on the CD button and “DVD player” on the DVD button. By  
completing the following procedure, you can change this setting so  
that you can set up any component on these buttons.  
qh To display the Top Menu.  
you want to set up.  
The Commander can be set up to operate only one component per  
button – unless their code numbers happen to be the same. For  
example, you cannot set up the Commander to operate a Sony TV  
and a Panasonic TV simultaneously (because they use different  
code numbers).  
q; To exit the setting menu.  
qf To use the “FAVORITE” function.  
qg CH+: Channel up.  
CH: Channel down.  
qh To turn on the display of a  
shortcut menu.  
zREC. First release N,  
then release zREC.  
To stop recording,  
perform the same  
procedure.  
.
CBL  
VCR  
AMP  
1 While pressing the SET button, press the POWER button.  
m: To rewind.  
t
,
t ENT on the N button,  
, and ENT in sequence, and then  
qg CH+: Channel up  
M: To fast-forward.  
zREC:To record, press N  
while pressing zREC.  
*
To avoid accidental recording, the REC key does not work unless pressed for  
more than 1 second (factory setting).  
Note  
2 Press the AMP button.  
3 Press the VOL+ button.  
4 Press the ENT button.  
CH: Channel down  
On the VCR, CBL, SAT, AMP, CD, and DVD buttons, “video cassette  
recorder”, “analog cable box”, “digital satellite receiver”, “receiver”,  
“CD player”, and “DVD player” are assigned respectively at the  
factory. But you can also assign other components on these buttons.  
For details, see “Changing the Component Type on the VCR, CBL,  
SAT, AMP, CD, and DVD buttons.”  
qj To change the input mode.  
qk To call up the MENU display.  
ql To move the cursor upward,  
downward, to the left, or to the  
right, or to enter the selection.  
X:  
To pause.  
*3x: To stop.  
You may not be able to operate even a Sony brand component with  
the factory presetting. In such a case, follow the procedure in  
“Setting the Code.”  
*3X: To pause.  
.
The volume control setting is changed to “receiver/amplifier.” You  
can control the volume of the receiver (or amplifier) of the AMP  
button while selecting any component.  
3
*
The operation of the built-in DVR or the video on demand.  
 

Sony Car Stereo System XR M550 User Manual
Sony Cassette Player TC KE240 User Manual
Sony Headphones STM10 User Manual
Sony Portable DVD Player DVP FX850 User Manual
Spirit Treadmill XT600 User Manual
SPX Cooling Technologies Humidifier Evaporative Cooling User Manual
Sub Zero Refrigerator 736TR User Manual
Sunbeam Kitchen Grill GC4600 User Manual
SVA Security Camera CRR 1101 User Manual
System Sensor Smoke Alarm DH100ACDC User Manual