Sony Projector VPD LE100 User Manual

BID SPECIFICATION  
FOR  
DLP PROJECTORS  
MODEL NUMBER  
VPD-LE100  
INSTRUCTIONS:  
REMOVE THIS COVER PAGE AND ADD TO REQUESTS FOR QUOTATION AND  
PROPOSALS. THE OBJECTIVE OF THIS BID SPECIFICATION IS TO ASSIST YOU IN  
CLEARLY SPECIFYING THE SONY PRODUCT IDENTIFIED ABOVE, AND ENSURING  
THAT THE BUYER IS WELL INFORMED OF THE HIGH STANDARD OF  
PERFORMANCE THAT IS TO BE EXPECTED OF A SONY PRODUCT. THE  
INFORMATION IN THIS DOCUMENT IS CURRENT AS OF JUNE 2002. PRODUCT  
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.  
SONY ELECTRONICS INC.  
DISPLAY PRODUCTS GROUP  
1 SONY DRIVE, MD S3D9  
PARK RIDGE, NJ 07656  
TEL# (201)-930-1000, FAX# (201)-358-4303  
 
720P (60Hz)  
1035I (60 Hz)  
1080I (50 and 60 Hz)  
1080P (24 PsF)  
VGA Computer Graphics (Modes 1, 2 and 3, 60 - 85 Hz)  
VESA 800x600 Computer Graphics (56 - 85 Hz)  
VESA 1024 x 768 Computer Graphics (43 – 85 Hz)  
VESA 1152 x 864 Computer Graphics (70 – 75 Hz)  
SUN 1152 x 900 Computer Graphics (65 – 76 Hz)  
VESA 1280 x 1024 Computer Graphics (43 – 85 Hz)  
VESA 1600 x 1200 Computer Graphics (60 - 75 Hz)  
Mac 13” Computer Graphics  
Mac 16” Computer Graphics  
Mac 21” Computer Graphics  
This device shall accept multi-scanning sources, with scan frequencies ranging  
from 15 to 100 kHz Horizontally, and 40 to 120 Hz Vertically.  
This device shall employ the use of a high performance interpolation circuit,  
which regenerates a high-resolution sampling of the original signal by referring to  
memorized waveform patterns to enhance image performance. This device shall  
also employ the use of a 3-dimensional comb filter and 3-line filter for maximum  
chrominance and luminance separation and to minimize dot interference and  
cross color when viewing NTSC video sources.  
This device shall have the ability to store and recall multiple memory presets for  
various video and computer configurations.  
4.0 User Interface / Controllability Information  
Control of this device shall be accomplished through one of the following  
methods:  
Backlit, projector control panel  
Wired / Wireless backlit projector remote control  
Serial control jack for control by external control systems  
Advanced serial control jack for control by external control systems  
Advanced serial control jack for control by external signal switchers  
All of these control methods shall be standard to the device, or available at an  
additional charge if considered an optional accessory.  
The projector control panel shall be recessed into the cabinet, and shall employ  
the use of a backlight that activates when any button is pressed. The backlight  
shall have a timeout function. The control panel shall activate multi-language on-  
screen menus, which navigate the operator through setup and configuration of  
 
the device. The device shall be addressable for control over multiple devices  
from a single remote control.  
The wired / wireless backlit projector remote control shall operate in the same  
fashion as the projector control panel, and shall accommodate infrared wireless  
operation, or operation via a standard mini-plug cable. An infrared extender shall  
be available from the device manufacturer for operation of the device wirelessly  
in a rear-screen or cabinet environment.  
The serial control jack shall employ the use of a standardized device control  
protocol that is commonly accepted and understood by control systems  
manufacturers. This control jack shall accept unidirectional serial commands that  
provide full control over the device.  
The advanced serial control jack shall employ the use of a standardized device  
control protocol that is commonly accepted and understood by control systems  
manufacturers. This control jack shall accept and transmit bi-directional serial  
commands that provide full control over the device, and provide  
acknowledgement to the control system of the received command.  
The advanced serial control jack for control by external signal switchers shall  
employ the use of a standardized device control protocol that is commonly  
accepted and understood by control and signal switching manufacturers, and  
shall operate at distances greater than 1000 feet without regeneration from an  
external device. This control jack shall accept and transmit bi-directional serial  
commands that provide full control over the device, and provide  
acknowledgement to the control system of the received command.  
The following device functions shall be available for control:  
Power On / off  
Input Selection  
Brightness / Contrast  
Video Decoder Functions  
Audio Volume  
Memory Recall Functions  
White Balance  
Gain / Bias Control  
Image Sizing  
Image Positioning  
Lens Power Zoom  
Lens Power Shift  
Lens Power Focus  
 
5.0 Performance Specifications  
This device shall employ the use of 3 Texas Instruments high-resolution 1.1-inch  
DMD chips. This device shall provide a light output of 10,000 ANSI lumens, when  
measured using a 1280 x 1024 native resolution signal.  
This device shall include a standard power zoom / focus / shift lens, and other  
lenses shall be available as options for a variety of short-throw and long-throw  
applications.  
This device shall have a minimum RGB resolution of 1280 by 1024 pixels and a  
minimum video resolution of 600 TV lines.  
An automatic dot-phase adjustment technology shall be employed to optimize the  
display to the input source without user intervention.  
This device shall employ the use of a flat-spectrum xenon lamp system, providing  
for optimum balance between the red, green and blue color spectrum.  
This device shall employ the use of a 2-3 pulldown technique for accurate and  
detailed reproduction of film originating source material.  
A 13-bit signal processing shall be employed for accurate, smooth reproduction  
of color and grayscale images.  
6.0 Dimensional Information  
This device shall have maximum cabinet dimensions of 13.75 inches high by  
28.63 inches wide and 37.38 inches deep.  
This device shall not weigh more than 209 pounds.  
7.0 Connectivity Information  
This device shall provide for connection of 4 source devices simultaneously,  
without employing the use of an external switching device. One of these  
connections shall be a standard input on the device, with 3 available for custom  
configuration. The standard connection shall include the following:  
RGB Computer / Component Video / HDTV Video (Sync on Green, Composite,  
or Separate Sync) on BNC Connectors  
Optional Modules shall allow for the following connections:  
RGB Computer / Component Video (Sync on Green, Composite, or Separate  
Sync) on BNC Connectors  
 
Audio L/R on RCA (Phono) Connectors  
RGB Computer / Component Video (Sync on Green, Composite, or Separate  
Sync) on a 9 pin (D9) Connector  
Audio L/R on RCA (Phono) Connectors  
RGB Computer / Component Video (Sync on Green, Composite, or Separate  
Sync) on a VGA (HD15) Connector with loop-through  
Audio L/R on RCA (Phono) Connectors  
Component Serial Digital Video on a BNC Connector with loop-through  
Composite Video on a BNC Connector or Y/C Video on a 4 Pin DIN Connector,  
both with loop-through  
Audio L/R on RCA (Phono) Connectors  
High Definition Serial Digital Video on a BNC Connector with loop-through  
These optional modules shall be user-installable, without access to the inside of  
the device, and shall also be installable in an optional external switching device  
available from the device manufacturer.  
This device shall include a 12V power output for providing power to external  
devices.  
8.0 Power Requirements  
This device shall accept power from 220 to 240 VAC at either 50 or 60 Hz.  
This device shall consume no more than 2800 watts.  
This device shall emit no more than 9556 BTU.  
Power to this device shall be supplied via a detachable standard power cord that  
is readily available for replacement from local suppliers.  
 
9.0 Safety Compliance Information  
This device shall be fully compliant with the following standards:  
UL 1950  
cUL 950  
FCC Class A  
IC Class A  
VCCI Class A  
JEIDA  
EN60 950  
CE  
C-Tick  
10.0 Warranty Information  
This device shall carry a 2-year manufacturer’s warranty, with a 90-day lamp warranty.  
Authorized servicing dealers of the devices’ manufacturer shall perform warranty  
service.  
 

Sennheiser Stereo Receiver EM 3532 U User Manual
Shark Carpet Cleaner S3101W N User Manual
Sharp Projector XG MB55X L User Manual
Shure Computer Monitor French User Manual
SIIG Battery Charger 04 0599A User Manual
Smooth Fitness Treadmill 945ST User Manual
Sony Indoor Furnishings PSS 610 User Manual
Sony Music Pedal FS 85B50 User Manual
Sprint Nextel Cordless Telephone SYSTEM 1 User Manual
Sylvania DVD Player DVL500B User Manual