Sony Speaker AIRSA10 User Manual

Notice for the customers in Canada  
3-288-619-11(1)  
Precautions  
Preparing the unit  
Connect the unit and S-AIR main unit to listen to sound from the S-AIR main unit.  
For the wireless transceiver (EZW-RT10)  
is device complies with RSS-Gen of IC Rules.  
Operation is subject to the following two conditions:  
(1) this device may not cause interference, and (2)  
this device must accept any interference, including  
interference that may cause undesired operation of the  
device.  
Notes on use of the S-AIR product  
As the S-AIR product transmits sound by radio waves,  
sound may skip when radio waves are obstructed.  
is is a characteristic of radio waves and is not a  
malfunction.  
As the S-AIR product transmits sound by radio waves,  
equipment that generates electromagnetic energy,  
such as a microwave oven, may interfere with sound  
transmission.  
As the S-AIR product uses the radio waves that share  
the same frequency as other wireless systems, such  
as wireless LAN or Bluetooth devices, interference or  
poor transmission may result. In this case, take the  
following steps:  
Wireless  
Speaker System  
is equipment complies with IC radiation exposure  
limits set forth for uncontrolled equipment and meets  
the RSS-102 of the IC radio frequency (RF) Exposure  
rules.  
is equipment should be installed and operated with at  
least 20cm and more between the radiator and person’s  
body (excluding extremities: hands, wrists, feet and  
ankles).  
EZW-RT10/Wireless transceiver  
Operating Instructions  
Do not install the S-AIR product near other wireless  
systems.  
Do not use the S-AIR product and the other wireless  
systems at the same time.  
Notice for the customers in  
Australia  
AIR-SA10  
e transmission distance differs depending on  
the usage environment. Find a location where  
transmission between the unit and the S-AIR main  
unit is most effective, and install the unit and the S-  
AIR main unit there.  
For the wireless transceiver (EZW-RT10)  
is equipment should be installed and operated with at  
least 20cm and more between the radiator and person’s  
body (excluding extremities: hands, wrists, feet and  
ankles).  
Wall socket  
Printed in China  
© 2008 Sony Corporation  
On safety  
Completely disconnect the power cord (mains  
lead) from the wall socket (mains) if it is not going  
to be used for an extended period of time. When  
unplugging the unit, always grip the plug. Never pull  
the cord itself.  
Should any solid object or liquid get into the unit,  
unplug the unit, and have it checked by qualified  
personnel before operating it again.  
1
Insert the supplied wireless transceiver (EZW-RT10)  
securely into the EZW-RT10 slot on the rear of the  
unit.   
Check the orientation of the mark when inserting  
the supplied wireless transceiver (EZW-RT10).  
Failure to do so may result in damage to the unit.  
4
Press the PAIRING button on the rear of the unit  
using a pointed object.  
12)Use only with the cart, stand,  
“S-AIR” and its logo are trademarks of Sony  
Corporation.  
e Bluetooth word mark and logos are owned  
by the Bluetooth SIG, Inc. and any use of such  
marks by Sony Corporation is under license. Other  
trademarks and trade names are those of their  
respective owners.  
When pairing is performed, the S-AIR indicator  
flashes and the display changes as follows:  
tripod, bracket, or table specified  
WARNING  
by the manufacturer, or sold with  
“PAIRING” “COMPLETE”  
To cancel pairing, change the S-AIR IDs of the unit  
and the S-AIR main unit to different S-AIR IDs.  
To stop the pairing operation midway, press the  
PAIRING button again.  
the apparatus. When a cart is used,  
To reduce the risk of fire or electric shock,  
do not expose this apparatus to rain or  
moisture.  
use caution when moving the  
2
3
Set the S-AIR ID of the unit to the same S-AIR ID as  
the S-AIR main unit to be connected.   
For details on setting the S-AIR ID of the S-AIR  
main unit, refer to the Operating Instructions  
supplied with the S-AIR main unit.  
cart/apparatus combination to avoid  
e AC power cord can be changed only by a qualified  
service facility.  
injury from tip-over.  
13)Unplug this apparatus during lightning storms or  
when unused for long periods of time.  
14)Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as power-supply cord or  
plug is damaged, liquid has been spilled or objects  
have fallen into the apparatus, the apparatus has  
been exposed to rain or moisture, does not operate  
normally, or has been dropped.  
Indoor use only.  
On placement  
Notes  
Do not place the unit in an inclined position or in  
locations that are extremely hot, cold, dusty, dirty, or  
humid or lacking adequate ventilation, or subject to  
vibration, direct sunlight or a bright light.  
Be careful when placing the unit on surfaces that have  
been specially treated (for example, with wax, oil,  
polish) as staining or discoloration of the surface may  
result.  
To reduce the risk of fire, do not cover the ventilation  
opening of the apparatus with newspapers, tablecloths,  
curtains, etc. Do not place the naked flame sources such  
as lighted candles on the apparatus.  
Make sure to turn off the unit when inserting or removing the  
supplied wireless transceiver (EZW-RT10). Failure to do so may  
result in damage to the unit.  
Connect the power cord to a wall socket.   
If the plug does not fit the wall socket, detach the  
supplied plug adaptor (only for models equipped  
with an adaptor).  
Do not touch the terminals of the supplied wireless transceiver  
(EZW-RT10).  
Do not insert any device other than the supplied wireless  
transceiver (EZW-RT10) into the EZW-RT10 slot.  
To reduce the risk of fire or electric shock, do not  
expose this apparatus to dripping or splashing, and do  
not place objects filled with liquids, such as vases, on the  
apparatus.  
4
5
Press   
to turn on the unit.   
Operate the S-AIR main unit to turn on the S-AIR  
function.  
For details on turning on the S-AIR function, refer to  
the Operating Instructions supplied with the S-AIR  
main unit.  
S-AIR (Sony Audio Interactive Radio  
frequency)  
Recent times have seen the rapid spread of DVD  
media, Digital Broadcasting, and other high-quality  
media.  
To ensure that the subtle nuances of these high-  
quality media are transmitted with no deterioration,  
Sony has developed a technology called “S-AIR”  
for the radio transmission of digital audio signals  
with no compression, and has incorporated this  
technology into the EZW-RT10.  
is technology transfers digital audio signals with  
no compression using the 2.4 GHz band range of ISM  
band (Industrial, Scientific, and Medical band), such  
as wireless LANs and Bluetooth applications.  
The following FCC statement  
applies only to the version of this  
model manufactured for sale in  
the U.S.A. Other versions may  
not comply with FCC technical  
regulations.  
On heat buildup  
Heat buildup on the unit during operation is normal  
and is not cause for alarm.  
Do not touch the cabinet if it has been used  
continuously at a high volume because the cabinet  
may have become hot.  
As the main plug is used to disconnect the unit from  
the mains, connect the unit to an easily accessible  
AC outlet. Should you notice an abnormality in the  
unit, disconnect the main plug from the AC outlet  
immediately.  
Once the connection is established, the S-AIR  
indicator  
on the front of the unit lights up  
e unit is not disconnected from the mains as long as it  
is connected to the AC outlet, even if the unit itself has  
been turned off.  
and “LINKED” appears in the display for about 2  
seconds.  
Do not obstruct the ventilation holes.  
On the speaker system  
NOTE:  
If you cannot connect to the S-AIR main unit  
It is easy to set the same S-AIR ID for the unit and S-  
AIR main unit to establish the connection.  
However, if a neighbor has an S-AIR main unit with the  
same S-AIR ID as your S-AIR main unit, you may be  
able to hear the audio transmitted from your neighbors  
S-AIR main unit on your system. To prevent this, you  
can identify the unit with a specific S-AIR main unit by  
performing the pairing operation.  
is speaker system is not magnetically shielded, and  
the picture on nearby TV sets may become magnetically  
distorted. In this situation, turn off the TV, wait about  
15 to 30 minutes, and turn it back on.  
Do not install the appliance in a confined space, such as  
a bookcase or built-in cabinet.  
is equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. ese limits are designed  
to provide reasonable protection against harmful  
interference in a residential installation. is equipment  
generates, uses and can radiate radio frequency energy  
and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that  
interference will not occur in a particular installation.  
If this equipment does cause harmful interference to  
radio or television reception, which can be determined  
by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or  
more of the following measures:  
e nameplate is located on the bottom exterior.  
If there is no improvement, move the unit far away from  
the TV.  
Notice for the customers in the  
U.S.A.  
Cleaning the cabinet  
e following indications are located on the bottom  
exterior.  
Clean this unit with a soſt dry cloth. Do not use any  
type of abrasive pad, scouring powder, or solvent, such  
as thinner, benzine, or alcohol.  
When you perform pairing  
Before pairing, the connection is established by the S-  
AIR ID (example).  
Your system  
Neighboring system  
is symbol is intended to alert the  
user to the presence of uninsulated  
“dangerous voltage” within the  
product’s enclosure that may be of  
sufficient magnitude to constitute a  
risk of electric shock to persons.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and  
receiver.  
This unit  
ID A  
Connect the equipment into an outlet on a  
circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV  
technician for help.  
is symbol is intended to alert the  
user to the presence of important  
operating and maintenance (servicing)  
instructions in the literature  
accompanying the appliance.  
ID A  
ID A  
CAUTION  
You are cautioned that any changes or modifications  
not expressly approved in this manual could void your  
authority to operate this equipment.  
S-AIR main unit  
S-AIR main unit   
Owners Record  
e model and serial numbers are located on the  
bottom of the unit. Record these numbers in the space  
provided below. Refer to them whenever you call upon  
your Sony dealer regarding this product.  
For the wireless transceiver (EZW-RT10)  
is device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received,  
including interference that may cause undesired  
operation.  
e connection is established between the paired unit  
and S-AIR main unit.  
Model No.  
Serial No.  
Your system  
Neighboring system  
Important Safety Instructions  
1) Read these instructions.  
This unit  
ID A  
is equipment must not be co-located or operated in  
conjunction with any other antenna or transmitter.  
2) Keep these instructions.  
3) Heed all warnings.  
4) Follow all instructions.  
is equipment complies with FCC radiation exposure  
limits set forth for uncontrolled equipment and meets  
the FCC radio frequency (RF) Exposure Guidelines in  
Supplement C to OET65.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
Pairing  
7) Do not block any ventilation openings. Install in  
accordance with the manufacturers instructions.  
8) Do not install near any heat sources such as  
radiators, heat registers, stoves, or other apparatus  
(including amplifiers) that produce heat.  
9) Do not defeat the safety purpose of the polarized  
or grounding-type plug. A polarized plug has two  
blades with one wider than the other. A grounding  
type plug has two blades and a third grounding  
prong. e wide blade or the third prong are  
provided for your safety. If the provided plug does  
not fit into your outlet, consult an electrician for  
replacement of the obsolete outlet.  
10)Protect the power cord from being walked on  
or pinched particularly at plugs, convenience  
receptacles, and the point where they exit from the  
apparatus.  
11)Only use attachments/accessories specified by the  
manufacturer.  
is equipment should be installed and operated with at  
least 20cm and more between the radiator and person’s  
body (excluding extremities: hands, wrists, feet and  
ankles).  
ID A  
ID A  
S-AIR main unit   
S-AIR main unit   
1
2
3
Check that the power of the unit and the S-AIR  
main unit to be connected are turned on.  
Check that the S-AIR ID of the unit is the same as  
the S-AIR ID of the S-AIR main unit.  
Operate the S-AIR main unit to turn on the pairing  
function.  
For details on turning on the pairing function, refer  
to the Operating Instructions supplied with the S-  
AIR main unit.  
 

Sony Camcorder HXR MC2000U User Manual
Sony Car Stereo System CDXGT300S User Manual
Sony Car Stereo System NSZ GS7 User Manual
Sony Home Theater System 3 283 375 112 User Manual
Sony Portable DVD Player PBD V30 User Manual
Sony Speaker System SAVA 700 User Manual
Sony TV Mount MB 502B User Manual
Sungale Digital Photo Frame PF 1023 User Manual
Symphonic TV VCR Combo SC1302 SC1902 User Manual
TANDBERG Computer Monitor 6000 MXP User Manual