FADER CLEANING
The SK ONE faders may need lubrication from time to time. This will extend the
fader life and eliminate any potential damage due to extended heavy usage.
S K O N E Professional performance mixer
Cleaning Instructions
cable coming from the mixer.
1. Remove the 3 fader knobs and 4 screws
located in the corners of the PROTEKT™
3. Spray a small amount of cleaner or
lubricant into both ends of the fader and
slide the fader back and forth a few times
to spread the fluid evenly throughout the
fader.
(see “
” inside) panel
and take the panel off the mixer.
2 . Remove the fader to be cleaned by
unscrewing the 2 outer screws (removing
the 2 inner screws will detach the fader
from the fader plate) and disconnect the
4. Shake and wipe off excess fluid before
re-assembling the fader.
REPL ACEMENT PARTS
To replace the cross or channel faders, follow steps 1 and 2 of the cleaning
instructions. The following replacement parts are available from Stanton or your
local Stanton dealer.
PL-SK1
Two way input toggle switch
PP-SK1
PROTEKT™ panel
3PL-SK1 Three way input toggle
switch with FLASH™
PS-13US US Power Supply (110v)
LF-SK1
CF-SK1
Channel input fader
Crossfader
PS-13EU European Power Supply (220v)
PS-13UK UK only Power Supply (240v)
ROTATING AND REPLACING THE INPUT TOGGLE SWITCHES
REPLACING INSTRUCTIONS
ROTATING INSTRUCTIONS
1. Remove the PROTEKT™ panel
1 . Remove the PROTEKT™ panel
O W N E R ’S M A N U A L
2. Remove the 2 outer screws from the tog-
gle switch plate (removing the 2 inner
screws will detach the switch from the
plate)
2. Remove the 2 outer screws from the tog-
gle switch plate (removing the 2 inner
screws will detach the switch from the
plate)
3. Remove the switch assembly and dis-
connect the cable coming from the mixer.
3. Rotate the plate to the desired position
and tighten the screws back in the top and
bottom holes
4. Set the replacement switch assembly in
the desired position and place the screws
back in the top and bottom holes.
S TANTON M AGNETICS , LLC
2 8 2 1 Evans St. Hollywood, FL 3 3 0 2 0
(9 5 4 ) 9 2 9 -8 9 9 9 - Fax: (9 5 4 ) 9 2 9 -0 3 3 3
info@stantonmagnetics.com
© 1999, Stanton Magnetics, LLC
DESCRIPTION OF FUNCTIONS
normal (20dB), or long (30dB) fade.
8. Channel fader: Controls the input channel level.
9. Crossfader: Fades the master output between channels 1 and 2.
10. Master level control: Controls the overall signal output level.
11. Crossfader Curve adjustment: Adjusts the shape of the crossfader curve from a quick cut
for scratching and cutting to a longer fade for mixing.
12. Crossfader Reverse: Reverses the direction of the crossfader. Bi-color LED indicates the
status of the crossfader reverse function. When LED is green, the crossfader is normal.
When LED is red, the crossfader direction is reversed.
13. Headphone level control: Controls the overall headphone output level. It is recommend-
ed headphones with an impedance rating of 200 ohms or less be used for maximum vol-
ume.
14. Cue pan: Fades the headphone output between channels 1 and 2, effectively allowing the
user to preview a mix.
1. Gain control: Controls the input sensitivity of each channel.
2. EQ: Individual controls for low and high frequency equalization with (+9/-26 dB)
Any changes made to EQ settings will change the overall output level.
3. Pan control: Controls left/right output balance of each channel.
4. Input Fader Reverse: Reverses the direction of each respective input channel fader.
Includes bi-color LED to indicate the status of the reverse function. When LED is green,
the fader is normal. When LED is red, the fader direction is reversed.
5. Input Level Meter: Monitors each channel’s input level.
6. Input selector switches: Selects phono or line inputs.
7. Input Fader Curve Adjustment: Adjusts the curve of the input faders between quick (6dB),
FU N C TI O NS (cont’d)
TECHNIC AL SPECIFIC ATIONS
Line inputs:
Phono inputs:
Master output:
2 (RCA), 150 mV / 27K ohm
2 (RCA), 3 mV / 47K ohm
1 (1/4” TRS Balanced/RCA unbalanced),
775 mV / 1K ohm
15. Headphone output: Connection for 1/4 inch headphone. Recommended headphone
impedance is 32-200 ohms for maximum volume.
Record output:
Headphone output:
Frequency Response:
Tone Control :
Gain Control:
S/N Ratio:
T.H.D:
Dimension(LxWxD):
Weight:
1 (RCA), 245 mV / 10K ohm
1 (1/4 inch), 32 - 200 ohms recommended
20 Hz - 20 kHz, +/- 2 dB
+ 9/-26 dB (Hi, Low)
0-20dB
Less than 70dB
less than 0.2%
13 6/8” x 7 2/8” x 4” ( 350 x 184 x 102 mm)
7 lbs (3.2 Kg)
16. Master output: TRS balanced (1/4”).
17. Power switch: Selects power "ON" or "OFF".
18. Power supply connector: Input connection for the accompanying power supply.
19. Ground connector: Connects to the turntable ground connector to eliminate electrical
hum. Ground connectors usually supplied with turntables.
20. Channel inputs: Line and phono signal inputs. Line inputs are used to connect to
line level sources such as CD players, samplers, tape players, etc. Phono
inputs are used to connect to turntables. Master output connects to an ampli-
fier, EQ, crossover, or other outboard signal processing. Record out connects
to tape recorder, mini disk recorder, etc.
21. Outputs: Rec and unbalanced master outputs.
WARRANT Y
SPECIAL PROTE K TI O N
This unit has been designed and manufactured using quality
components. Therefore, it is warranted to be free from defects in materi-
als (limited as specified below), and workmanship for a period of twelve
(12) months from the original purchase date. During this period, all
service and parts necessary to repair a defect will be free of charge. This
limited warranty applies to mechanical parts which are subject to wear
and tear as specified:
Your SK ONE comes with a special PROTEKT™ aluminum panel designed to
make the surface of the mixer is as smooth as possible while still enabling you
to field-replace key components. The PROTEKT™ panel covers all screws that
may get in the way of your performance. You can still easily remove the front
panel to replace any of the modular parts which are subject to wear and tear:
crossfader, input faders and input toggle switches.
• Faders, specified durability: 15,000 cycles
• Rotary potentiometers, specified durability: 10,000 cycles
• Switches, specified durability: 10,000 cycles
Consequently, the parts listed above are warranted to be free from
defects in materials and workmanship for a period of thirty days (30)
days from the original purchase date.
FOR THE WARRANTY TO BE VALID, PLEASE COMPLETE THE
ONLINE WARRANTY REGISTRATION FORM FOUND AT
WWW.STANTONMAGNETICS.COM
2821 Evans Street • Hollywood, FL 33020
|