Stiga Lawn Mower 85 M User Manual

D
DEUTSCH  
85 M  
8211-3502-01  
 
10.  
9.  
Z
X
V
Y
W
11.  
Denna produkt, eller delar därav, omfattas av följande  
mönsterskydd:  
This product, or part of it, is covered by the following  
design registration:  
Sverige/Sweden  
62 435  
3
 
GB  
ENGLISH  
SYMBOLS  
ASSEMBLY  
The following symbols are displayed on the ma-  
chine in order to remind you about the safety pre-  
cautions and attention necessary when using the  
machine.  
MOWER DECK  
1. Remove both mounting bolts D on the base ma-  
chine (fig 3).  
The symbols mean:  
2. Insert both spacer sleeves E in the mower deck's  
arms (fig 4). The spacer sleeves are supplied in a  
plastic bag.  
Warning!  
Read the instruction book and safety man-  
ual before using the machine.  
3. Bolt the mower deck to the base machine.  
Warning!  
4. Pull the v-belt onto the mower deck's pulley.  
(This is carried out easier if the height adjustment  
lever is in position "5").  
Do not put hands or feet under the cover of  
the machine when it is running.  
5. Make sure that the tension roller J is on the out-  
side of the v-belt (figs 2 and 5).  
Warning!  
Beware of objects being flung out. Keep  
spectators away.  
6. Hook the spring into the bracket G (figs 2 and 5).  
7. Screw the guard H in position using three screws  
(fig 6). The screws are supplied in the plastic bag.  
Warning!  
Beforestarting any repair work, remove the  
spark plug cable from the spark plug.  
8. Hook the chain I and lifting spring F in the attach-  
ment's lift arm (fig 6).  
SETTING  
For the mower deck to mow evenly and cleanly it  
needs to be adjusted correctly:  
INTRODUCTION  
The power outlet's tension roller and tension arm's  
spring on the base machine are available in two ver-  
sions (figs 1 and 2).  
1. Make sure the tyre pressure is correct:  
Front: 0.4 bar (6 psi).  
Rear: 1.2 bar (17 psi).  
NOTE! To be able to fit this mower deck ("Multi-  
clip" mod. 85M) version B is required.  
2. Place the machine on a flat surface. Loosen the  
screws K (fig 7).  
VERSION A:  
(Standard on models made between 1982 - 83).  
3. Adjust the mower deck so that the casing's front  
and rear edges are the same height from the floor.  
If the base machine is fitted with version A a sepa-  
rate assembly set is required to be able to fit the  
mower deck.  
4. Tighten the screws.  
USE  
Assembly set, art. No.: 13-1967-11.  
The set contains a v-belt, tension roller, spring, as-  
sembly components and assembly instructions.  
MOWING HEIGHT  
The mower deck has 17 fixed mowing heights, from  
30 mm to 80 mm.  
N.B. Older base machines can, however, be fitted  
with version B if they have previously been adapted  
for use with a "Multiclip" mower deck.  
N.B. The stated mowing heights apply when the  
machine is standing on firm ground.  
VERSION B:  
(Standard on machines made from 1994 - ).  
MOWING ADVICE  
For the best "Multiclip" effect follow this advice:  
- mow regularly.  
The mower deck can be fitted directly.  
- use full throttle on the engine.  
4
 
GB  
ENGLISH  
- keep the underside of the mower deck clean.  
chine.  
- use sharp blades.  
8. Now refit the mower deck on the base machine.  
- do not mow wet grass.  
- mow twice (using different mowing heights)  
if the grass is long.  
CHANGING BLADES  
Use protective gloves to prevent cuts  
when changing blades/blade tips.  
MAINTENANCE  
Make sure the blades are always sharp. This gives  
the best mowing results.  
No service action must be taken on the  
mower deck unless:  
- the engine has been stopped.  
- the ignition key has been removed.  
- the spark plug cap has been removed  
from the spark plug.  
- the parking brake is engaged.  
- the mower deck is disengaged.  
Always check the blade(s) after an impact. If the  
blade system has been damaged the defective parts  
must be changed.  
Always use original spare parts. Using  
non-original spare parts can result in  
the risk of damage even if they fit in the  
machine.  
CLEANING  
The cutting system consists of two blade bars, each  
with two interchangeable blade tips Y (fig 11).  
Both blade tips should be replaced at the same time  
to avoid any imbalance.  
After use, rinse off the underside of the mower  
deck using a garden hose.  
If grass cuttings have dried on to the attachment,  
dismantle the mower deck and scrape clean the un-  
derside.  
Fit the new blade tips. Tighten the screws V and W  
fully. Tightening torque: V - 9.8 Nm, W - 24 Nm.  
If necessary touch-up the underside using a suita-  
ble paint to prevent corrosion.  
And heavy impact can result in the blade tip being  
folded aside. Loosen the locking nut X and turn the  
blade tip back to its correct position. Mount a new  
shear bolt V. Tighten the lock nuts X and Z.  
CHANGING THE DRIVE BELT  
1. Remove the mower deck from the base machine.  
2. Remove the transmission casing.  
3. Loosen the tension arm L (fig 8).  
4. Loosen the right hand bearing box's fixing bolts  
M (fig 9).  
5. Fit the new drive belt.  
The new drive belt must be fitted so that  
the blades are square (90°) to each oth-  
er. See figure 10. If you fit the drive belt  
incorrectly the blades will hit each oth-  
er resulting in the blades being dam-  
aged.  
6. The belt is tensioned by pushing the tension arm  
L forwards and then securing in position.  
7. Tighten the bearing box's fixing bolts M.  
When the drive belt is fitted, check, by  
turning the mower deck over and turn-  
ing the blades, that it has been fitted  
correctly. NOTE! The mower deck  
should be dismantled from the base ma-  
5
 

Servis Rhino Paper Shredder RC 12 User Manual
Shindaiwa Vacuum Cleaner PS344 User Manual
Sonic Alert Clock Radio B31540 02 User Manual
Sony Cassette Player CFS 616L User Manual
Sony Laptop Docking Station SM4000 User Manual
Speed Queen Washer HA 5590 User Manual
Stamina Products Stepper Machine 40 0069 User Manual
StarDot Technologies Digital Camera net camera User Manual
Sunbeam Clock Radio 89019 User Manual
Sunbeam Electric Heater SCH8212 User Manual