|
StorCase® Technology
Data Express®
SerialATADE110
Removable
SATA Drive Enclosure
User's Guide
ii
LIMITEDWARRANTY
STORCASE TECHNOLOGY, Incorporated (“StorCase”) warrants that its products will be free
from defects in material and workmanship, subject to the conditions and limitations set forth
belowꢀ StorCase will, at its option, either repair or replace any part of its product that proves
defective by reason of improper workmanship or materialsꢀ Repair parts or replacement
products will be provided by StorCase on an exchange basis, and will be either new or
reconditioned to be functionally equivalent to newꢀ
This warranty does not cover any product damage that results from accident, abuse, misuse,
natural or personal disaster, external power surge or failure, or any unauthorized disassem-
bly, repair or modificationꢀ StorCase will not be responsible for any software, firmware or other
customer data stored within, or interfacing with a StorCase productꢀ
Duration of Warranty
Seven-Year Warranty: The following StorCase products are covered by this warranty for a
period of seven (7) years from the original date of purchase from StorCase or its authorized
®
®
®
resellers: all Data Express removable device enclosures and all Data Silo , Data Stacker and
®
InfoStation external expansion chassis, except for those components integrated into or
purchased separately for use with these products which are identified and covered by the three-
year or hard drive warranties described belowꢀ All StorCase interface cables and other
accessories specifically intended for use with the StorCase products identified above are also
covered by this (7) year warrantyꢀ
Three-Year Warranty: The following components integrated into or purchased separately for
use with StorCase Data Express, Data Silo, Data Stacker and/or InfoStation products are subject
to warranty for a period of three (3) years from the original date of purchase from StorCase or
its authorized resellers: all RAID controllers, power supplies, fans and blowersꢀ
Two-Year Warranty: The following StorCase products are covered by this warranty for a
period of two (2) years from the original date of purchase from StorCase or its authorized
®
resellers: all Rhino JR fixed external expansion chassis (model types “FJR”) and all RhinoJR
removable device enclosures (model types “RJR”)ꢀ
One-Year Warranty: All StorCase products identified as Reconditioned or “Special Inventory”
are covered by this warranty for a period of one (1) year from the original date of purchase from
StorCase or its authorized resellersꢀ Reconditioned products may only be exchanged for
reconditioned productsꢀ
Hard Disk Drive Warranty: All hard disk drives purchased from StorCase or through its
authorized resellers, whether purchased separately or integrated into StorCase products, are
subject to the warranty terms and conditions provided by the drive manufacturerꢀ
Third Party Software Warranty: All third party software purchased from StorCase for use
with and/or as part of StorCase products is subject to the warranty terms and conditions
provided by the software manufacturerꢀ
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
iii
Warranty Claim Requirements
To obtain warranty service, the defective product must be returned to your local authorized
StorCase dealer or distributor, or, with prior StorCase approval, to the StorCase factory
service centerꢀ
For defective products returned directly to StorCase, a Return Material Authorization (“RMA”)
number must be obtained by calling StorCase Customer Service at (714) 445-3455ꢀ The RMA
number must be prominently displayed on the outside of the return packageꢀ Shipments must
be freight-prepaid and insured, and must include the product serial number, a detailed
description of the problem experienced, and proof of the original retail purchase dateꢀ Products
must be properly packaged to prevent damage in transitꢀ Damage resulting from improper
packaging will not be covered by this warrantyꢀ The StorCase factory service center is located
at 17650 Newhope Street, Receiving Dock, Gate #4, Fountain Valley, CA 92780, UꢀSꢀAꢀ
Free Technical Support
StorCase provides free technical supportꢀ If you experience any difficulty during the
installation or subsequent use of a StorCase product, please contact StorCase’s Technical
Support Department prior to servicing your systemꢀ This warranty covers only repair or
replacement of defective StorCase products, as described aboveꢀ StorCase is not liable for,
and does not cover under warranty, any costs associated with servicing and/or installation
of StorCase productsꢀ
StorCase Technical Support can be reached in the UꢀSꢀ at (714) 438-1858 or toll-free at (888)
435-5460 (UꢀSꢀ and Canada only)ꢀ StorCase European Technical Support can be reached in
the UꢀKꢀ at +44 (0) 1932 738900ꢀ
Disclaimers
The foregoing is the complete warranty for the products identified above and
supersedes all other warranties and representations, whether oral or writtenꢀ
StorCase expressly disclaims all warranties for the identified products, which are
not stated herein, including, to the extent permitted by applicable law, any implied
warranty of merchantability or fitness for a particular purposeꢀ In no event will
StorCase be liable to the purchaser, or to any user of a StorCase product, for any
damages, expenses, lost revenues, lost savings, lost profits, or any other
incidental or consequential damages arising from the purchase, use or inability
to use a StorCase product, even if StorCase has been advised of the possibility
of such damagesꢀ
Copyright © 2004 StorCase Technologyꢀ All rights reservedꢀ All registered
trademarks are the property of StorCase Technologyꢀ All other logos and trademarks
are properties of their respective companiesꢀ
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
iv
Declaration of Conformity
Company Name:
StorCase Technology, Incꢀ
Corporate Office Address:
Manufacturing Address:
17600 Newhope Street
Fountain Valley, CA 92708
17600 Newhope Street
Fountain Valley, CA 92708
Product Name:
Model Number:
Data Express SATA DE110
S21B102, S21B105, S21J100, S21J101, S21J102,
S21J103, S21J104, S21J105, S21J106, S21J107
Conforms to the following standards:
EMC Directives:
(89/336/EEC)
ITEEmission
- EN55022: 1998
EN55024:1998ITEImmunity
- IEC 61000-4-2
- IEC 61000-4-3
- IEC 61000-4-4
- IEC 61000-4-6
- IEC 61000-4-8
Safety Standards:
CSA (NRTL/C)
CAN/CSA-C22ꢀ2 Noꢀ 950-95
UL 1950
TUV
EN 60950: 2000
EMI Standards:
EMC Standards:
FCC Part 15, Class B
AS/NZS 3548 Information Technology Equipment
Supplier's Code Number N10664
Year of Manufacture:
2003
Signature:___________________
Full name: Dieter Paul
Position: President
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
v
Table of Contents
INTRODUCTION ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 1
Packaging Information ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 1
Serial Numbersꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 1
Package Contents ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 2
General Description ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 3
"Universal" Receiving Frame Front Panel ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 4
SATA Drive Carrier ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 6
Receiving Frame Rear Panelꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 7
INSTALLATION ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 8
Preparation ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 8
Installing the Drive into the Carrierꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 8
Installing the "Universal" Receiving Frameꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 11
Spacer Plates (Optional) ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 12
Selecting the Unit ID Number ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 13
Unit ID Select Switch Settings ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 14
APPENDICES
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 15
Appendix A - Specifications/Dimensions ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 16
Appendix B - Optional Accessories ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 18
Carrying Case ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 18
Reader's Commentsꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 19
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
vi
List of Figures
Figure 1:
Figure 2:
Package Contents ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 2
SATA DE110 "Universal" Receiving Frame and Carrierꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 3
Figure 3A: "Universal" Receiving Frame Front Panel ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 5
Figure 3B:
Figure 4:
Figure 5:
Figure 6:
Figure 7:
"Universal" Receiving Frame Unit ID Number and Activity Display ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 5
SATA Drive Carrier ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 6
Receiving Frame Motherboard (Rear View)ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 7
Drive Installation Assemblyꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 8
Drive Cover Installation ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 10
Figure 8A: Receiving Frame Mounting Holes ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 11
Figure 8B:
Figure 9:
Spacer Plate Installation (Optional) ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 12
Unit ID Select Switch Location ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 14
Figure A-1: SATA DE110 Physical Dimensionsꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 17
Figure B-1: Carrying Case ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 18
List of Tables
Table 1:
Unit ID Select Switch Settings ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 14
NOTICE:
This User's Guide is subject to periodic updates without noticeꢀ While reason-
able efforts have been made to ensure the accuracy of this document,
StorCase Technology, Incꢀ assumes no liability resulting from errors or
omissionsinthispublication, orfromtheuseoftheinformationcontainedhereinꢀ
your StorCase representative for the latest revision of this documentꢀ
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
Introduction
1
INTRODUCTION
Packaging Information
The StorCase Technology Data Express® system is shipped in a container designed to provide
protection and prevent damage during shipmentꢀ The Data Express unit was carefully
inspected before and during the packing procedure at the factoryꢀ Bent or broken connectors,
or evidence of other damage to the Data Express should be reported to the shipper immediatelyꢀ
Refer to Figure 1 for the package contentsꢀ
If the wrong Data Express model has been received, please call your reseller or StorCase at
(800) 435-0642 to arrange for a Return Material Authorization (RMA)ꢀ StorCase cannot ac-
cept returns which do not display an RMA number on the outside of the packageꢀ Return the
unit with all the original packing materialsꢀ
Before removing any component from its packaging, discharge any static electricity by
touching a properly grounded metal objectꢀ
Serial Numbers
Both the SATA DE110 receiving frame and carrier are labeled with serial numbersꢀ These
numbers must be reported to the StorCase Customer Service Representative in order to
receive a Return Material Authorization (RMA) for warranty claimsꢀ Locate the serial number
labels and record the numbers in the spaces provided belowꢀ
Receiving Frame:
Device Carrier:
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
2
Introduction
Package Contents
NOTE:
Package contents may vary, depending on modelꢀ
The SATA DE110 package contents include the following itemsꢀ If any item is missing or
damaged, contact your StorCase dealer for a replacementꢀ
2
0834B
1
5
6
4
8
3
7
9
D
a
t
a
E
x
p
r
e
s
s
C
C
ab
o
v
l
e
(
P
e
r
o
r
vi
de
d)
D
(N is
ot
k
D
I
n
r
i
v
cl
e
ud
ed
P
)
ow
er
I/O
C
C
ab
le
ab
ID
le
S
el
ec
t
C
a
D
riv
b
e
le
C
ar
rie
r
D
H
riv
e
P
ar
d
M
e
3
/
h
i
lli
w
a
ou
(4
1
6
p
r
nt
s
F
#
in
g
)
la
6
e
t
H
-
32
a
D
x
C
S
ab
l
e
#
c
r
ew Co
2
01
6
51
Fl
-3
s
v
at
(
e
H
x
2
pl
r
D
3/
cs
16
)
Carrier &
Rec. Frame
Carrier
Only
Rec. Frame
Only
One Data Express
Serial ATA Removable Enclosure
1
1
1
4
1
1. Drive Carrier
2. “Universal” Receiving Frame
3. Drive Cover
1
4
1
4. #6-32 Phillips Machine Hd. Screws
5. #6-32 Phillips Flat Hd. Screws
6. Activity Indicator Cable
4
1
1
4
1
1
1
7. Alignment Tool
8. Drive Lock Keys
1 Set
1
1 Set
1
9. Insert Sheet
0834F
Figure 1: Package Contents
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
Introduction
3
General Description
NOTES:
Existing Parallel ATA DE110 carriers and new Serial ATA DE110 carriers will
both work in Serial ATA “universal" receiving framesꢀ “Universal" receiving
frames are indicated by their BLUE LEDꢀ Existing DE110 carriers are indicated
by a Data Express Logo, while the new Serial ATA DE110 carriers are indicated
by the Serial ATA logoꢀ
SATA DE110 carriers will only work in SATA DE110 "universal" receiving
frames (indicated by their BLUE LED)ꢀ Existing PATA DE110 receiving frames
are indicated by their GREEN LEDꢀ
For SATA (1ꢀ5Gbps) operation, a SATA controller and appropriate SATA cable
are requiredꢀ
The StorCase Technology Data Express® Serial ATA DE110 is a removable drive carrier and
"universal" receiving frame, designed to provide durable and reliable mounting for one (1) low-
profile (up to 1" high) 3ꢀ5" SATA drive within a 5ꢀ25" half-height peripheral slot (Figure 2)ꢀ
The SATA DE110 allows a drive to be removed and transported to another SATA DE110-
equipped computer or expansion chassis, and also provides the ability to secure sensitive data
by removing and storing the drive safely for future useꢀ
The SATA DE110 is the first removable drive enclosure for SATA host interfaces to provide
compatibility with both SATA and PATA drivesꢀ The SATA DE110 incorporates a unique
"universal" receiving frame (patent pending), capable of use with either a SATA or PATA
DE110 drive carrier!
0834C
“Universal” Receiving
Frame
Drive
Carrier
Figure 2: SATA DE110 "Universal" Receiving Frame and Carrier
This User's Guide describes the steps required to install the SATA DE110 removable enclosure
inside a computer peripheral bay or external expansion chassisꢀ This guide supplements
documentation provided with the host computer system, operating system, and the drive to
be installed within the carrierꢀ
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
4
Introduction
"Universal" Receiving Frame Front Panel
(Figures 3A & 3B)
•
•
Unit ID Number Indicator - This BLUE LED displays the status of the SATA DE110
device carrier if the carrier is Installed and Locked in the receiving frame or if the carrier
is removed from the receiving frameꢀ If the carrier is Installed but not Locked in the
receiving frame, a "u" will be displayed to indicate an unlocked conditionꢀ The unit ID
number is selected by means of the unit ID select switch inside the receiving frame using
a special alignment tool supplied with the SATA DE110 (Figure 9)ꢀ
The Activity Indicator - A small BLUE dot next to the unit ID number illuminates to indicate
when the host computer is accessing the data on the SATA DE110 carrierꢀ This dot
will flash during communication with the host computerꢀ
Some SATA drives/host controllers provide support for the Activity Indicator feature
(refer to the SATA drive/host controller manufacturer's documentation for further infor-
mation)ꢀ There are one of two ways to utilize the Activity Indicator:
1ꢀ Drive connection (cable included) to JP1 located on Drive Carrier Board (Figure 4)ꢀ
or
2ꢀ Host connection (cable not included) to J2 Pin 13 located on Receiving Frame
Motherboard (Figure 5)ꢀ
Use one method onlyꢀ Refer to the SATA drive/host controller manufacturer's documen-
tation for further informationꢀ
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
Introduction
5
“Universal”
Receiving Frame
BLUE Unit ID
Number Indicator
0840A
2.
BLUE Activity
Indicator
Figure 3A: "Universal" Receiving Frame Front Panel
Activity
Indicator
Carrier Removed
from Receiving Frame
Carrier Installed
(unlocked)
Carrier Installed
(locked)
The number "2" shown above is for illustration purposes only. The letter "u" (above
middle) will appear as illustrated.
0064E
Figure 3B: "Universal" Receiving Frame Unit ID Number
and Activity Display
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
6
Introduction
SATA Drive Carrier
(Figure 4)
• Key Lock/Drive Power Switch - Performs three functionsꢀ The key switch assures
proper seating of the drive carrier within the receiving frame, turns power to the drive
carrier ON and OFF, and prevents unauthorized removal or installation of the carrierꢀ For
the computer to access data on the disk drive, the key must be turned counterclockwise
to the locked positionꢀ
• JP1 -Provides a signal to the Activity Indicator (Figures 3A & 3B) when connected via
cable (provided) to the SATA driveꢀ Some SATA drives/host controllers provide support
fortheActivityIndicatorfeature(refertotheSerialATAdrive/hostcontrollermanufacturer's
documentation for further information)ꢀ
JP1
Red Cable
Black Cable
(Connect to Drive
Activity on Drive)
Serial ATA
Logo
0841A
Key Lock/Drive
Power Switch
Figure 4: SATA Drive Carrier
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
Introduction
7
"Universal" Receiving Frame Rear Panel
(Figure 5)
• I/O Connector (JP1) - The input/output connector provides a standard interface for all
SATA signals (Figure 5)ꢀ
• DC Power Connector (P1) - A standard 4-pin DC power connector is used to accept
DC powerꢀ
• Option Pins (W1)
Factory-Installed Jumper (ID0 & ID1) - Factory-installed jumperꢀ Refer to Table 1 for
on page 14 further informationꢀ
Factory-Installed Jumper (Pins 15 & 17) - Factory-installed jumperꢀ DO NOT remove!
Remote Activity LED (RLED) - These pins provide a remote LED device activity indicator
(Pin 13=Cathode, Pin 14=Anode)ꢀ
• Factory Reserved Pins - These pins are reserved for factory use only - Do not install
jumper under any circumstances!
• Activity Indicator - Pin 13 is used for host connection (cable not included) to the Activity
Indicator (Figures 3A & 3B)ꢀ Some SATA drives/host controllers provide support for the
Activity Indicator feature (refer to the SATA drive/host controller manufacturer's docu-
mentation for further information)ꢀ
Option Pin Connector
DC Power Connector
(W1)
(P1)
W1
1
3
2
4
+12
J2
P1
Factory-Installed
Jumper
+5
GND
14
13
JP1
Activity Indicator
(Pin 13)
P13
Cathode
P14
0839A
Reserved
(Pin 14)
= Pin 1
Anode
Remote
Activity LED
Factory Reserved Pins
(J2 - No Jumper Installed)
I/O Connector
(JP1)
Factory-Installed
Jumper
Figure 5: "Universal" Receiving Frame Motherboard
(Rear View)
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
8
Installation
INSTALLATION
NOTES:
Existing Parallel ATA DE110 carriers and new Serial ATA DE110 carriers will
both work in Serial ATA “universal" receiving framesꢀ “Universal" receiving
frames are indicated by their BLUE LEDꢀ Existing DE110 carriers are indicated
by a Data Express Logo, while the new Serial ATA DE110 carriers are indicated
by the Serial ATA logoꢀ
SATA DE110 carriers will only work in SATA DE110 "universal" receiving
frames (indicated by their BLUE LED)ꢀ Existing PATA DE110 receiving frames
are indicated by their GREEN LEDꢀ
For SATA (1ꢀ5Gbps) operation, a SATA controller and appropriate SATA cable
are requiredꢀ
Preparation
NOTE:
A #2 Phillips screwdriver will be required during this procedureꢀ
While performing the steps in this section, work on a soft surface to prevent excessive shock
to the drive being installedꢀ Also refer to the manufacturer's documentation provided with the
driveꢀ
1ꢀ Remove the drive from its protective packagingꢀ
2ꢀ Plastic Drive Bezel: If the drive came equipped with a plastic front bezel, it must
be removed before installing the drive into the drive carrierꢀ
Installing the Drive into the Carrier
1ꢀ Carefully insert the drive into the carrierꢀ Slide the drive towards the Drive Carrier
Board, so that the I/O connector on the drive mates with the connector on the Drive
Carrier Board (Figure 6)ꢀ Turn the drive/carrier assembly overꢀ
2ꢀ Fasten the drive into place with four (4) #6-32 Phillips Flat Hdꢀ screws (Figure 6)ꢀ
Some drives may require minor adjustment before securing into carrier with screwsꢀ
If drive supports the Activity Indicator feature, connect one end of the Activity
Indicator Cable (provided) to the drive and the other end to JP1 located on Drive
Carrier Board (Figures 4 & 6)ꢀ
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
Installation
9
NOTE:
Some SATA drives/host controllers provide support for the Activity Indicator
feature (refer to the SATA drive/host controller manufacturer's documentation
for further information)ꢀ
3ꢀ Install the provided drive cover (Figure 7)ꢀ
Optional Activity
Indicator Cable
(Included)
Serial ATA Drive
(Not Included)
JP1
Drive Carrier
Board
Drive
Carrier
0835B
#6-32 Phillips
Flat Hd. Screw
(4 each)
Figure 6: Drive Installation Assembly
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
10
Installation
1
Insert this end
into the carrier
first
2
Slide the cover
towards the back
of the carrier
0836A
3
Secure with #6-32
Phillips Flat Hd.
screws (2 Total)
Figure 7: Drive Cover Installation
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
Installation
11
Installing the “Universal” Receiving Frame
The drive should be installed into the carrier before installing the “universal” receiving frame
into the mounting bay of a computer or expansion chassisꢀ
NOTE:
Use a #2 Phillips screwdriver for this procedureꢀ
1ꢀ Turn OFF power to the computerꢀ
2ꢀ Open the computer system according to the manufacturer’s instructionsꢀ If
necessary, temporarily remove any expansion boards that may make installation
difficultꢀ
3ꢀ With the drive carrier locked in place inside the receiving frame, install the SATA
DE110 into the 5ꢀ25” drive opening in the computer or expansion chassisꢀ Use the
appropriate guides to position the Data Express, and fasten it into place with the four
(4) #6-32 Phillips screws providedꢀ Figure 8A illustrates the location of the mounting
holesꢀ Mounting holes are provided on each side and the bottom of the receiving
frame to accommodate a variety of mounting configurationsꢀ Use the mounting holes
which best suit the computer or expansion chassis configurationꢀ Note that bottom
mounting holes require self-tapping screws (not provided)ꢀ
4ꢀ Adjust the front of the receiving frame so the carrier slides freely in and out on the
receiving frame guidesꢀ The position of adjoining peripheral units may require
adjustmentꢀ
Front of Unit
Mounting
Holes
(Left)
Mounting
Holes
0837
(Right)
Mounting
Holes
(Bottom)
Figure 8A: Receiving Frame Mounting Holes
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
12
Installation
Spacer Plates (Optional)
The SATA DE110 is designed to fit most computer systems with standard 5ꢀ25" peripheral
slotsꢀ The installation of the spacer plates (provided) may or may not be necessaryꢀ
NOTE:
Depending on the computer system, spacer plates may be positioned on the
receiving frame to utilize either top or bottom row of side-mounting holes
(Figure 8B)ꢀ
Spacer Plate
(2 Total)
OR
0869
Figure 8B: Spacer Plate Installation (Optional)
5ꢀ ConnecttheI/Ocablefromthehostadaptertothereceivingframeꢀ ThePin1 indicator
on the cable must be properly alignedꢀ
6ꢀ Connect the power cable from the DC power supply in the computer or expansion
chassis to the power connector on the SATA DE110 “universal” receiving frameꢀ
Refer to Figure 5 for the SATA DE110 “universal” receiving frame power connector
locationꢀ
7ꢀ Replace any expansion boards that may have been removed earlierꢀ Replace the
system cover according to the manufacturer’s instructionsꢀ
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
Installation
13
8ꢀ Reconnect any system or peripheral cables removed earlierꢀ
9ꢀ Turn ON power to the computerꢀ If the installation has been successful, and all the
cables have been properly attached, the system should boot normallyꢀ Although the
computer may not recognize the SATA DE110 yet, the front panel display on the
SATA DE110 receiving frame should illuminateꢀ
10ꢀ The new drive may need to be formatted or initialized prior to use with the operating
system and applications softwareꢀ Refer to the drive and/or computer manufacturer's
documentation for formatting informationꢀ
Selecting the Unit ID Number
1ꢀ Verify that power is turned ON to the SATA DE110 “universal” receiving frame by
turning on your computerꢀ A number will appear in the unit ID display window if the
carrier is locked in placeꢀ
2ꢀ Unlock the SATA DE110 drive carrier and remove it from the receiving frameꢀ A "u"
will be displayed initially when the unit is unlocked but will return to a number when
the carrier is removed from the receiving frameꢀ
WARNING:
Unlocking the carrier unit switches DC power OFF to the driveꢀ Since
disk drives require a short amount of time to spin down, allow about
15 seconds before pulling the carrier unit out of the receiving frame
to avoid possible damage to the driveꢀ
3ꢀ Use the alignment tool supplied with the SATA DE110 to select the ID number of the
disk driveꢀ Refer to Figure 9 for the location of the ID Select Switch inside the
receiving frameꢀ
NOTE:
The unit ID number display is for ID display purposes onlyꢀ
4ꢀ After you have selected an appropriate unit ID number, replace the SATA DE110
carrier in the receiving frame, and LOCK IT IN PLACEꢀ
NOTE:
The lock on the SATA DE110 carrier functions as a lock and a DC
power switch for the carrier unitꢀ The lock must be engaged in order
to supply power to the carrier and installed driveꢀ
5ꢀ Reboot the computerꢀ The new disk is now ready for use, although it may have to
be formatted or initialized prior to use with your operating system and applications
softwareꢀ
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
14
Installation
Unit ID Select
Rotating Switch
Drive Carrier
Guide
0087a
Typical Data Express
Receiving Frame
Figure 9: Unit ID Select Switch Location
Unit ID Select Switch Settings
The following table lists the Unit ID Select Switch settings and the valid AT/IDE unit numbersꢀ
Please note that all invalid switch settings have X's through them and result in a blank display
in the receiving frame display windowꢀ
Table 1: Unit ID Select Switch Settings
Unit Select
Position
0
1
2
3
4
5
6
7
8
9
Parallel/
Serial ATA
Drive
1
0
2
3
1
4
LED Number
Display
Blank
2*
Blank Blank
3*
Blank Blank Blank
W1 Jumper
Position
Pins 3 & 4
Pins 1 & 2
0834G
*
Unit ID Select Switch must be rotated by alignment tool.
NOTE:
The unit ID number display is for ID display purposes onlyꢀ
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
15
APPENDICES
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
16
Appendix A - Specifications/Dimensions
Appendix A - Specifications/Dimensions
Specifications and dimensions below are for reference onlyꢀ
Environmental
Specifications
Operating
Storage
0° C to 50° C
-40° C to 70° C
10% to 90%
Ambient Temperature
Relative Humidity (1)
10% to 80%
-1000 to 40,000 ft
-305m to 12195m
-1000 to 10,000 ft
-305m to 3048m
Altitude
Shock (2)
10g
60g
(1) Non-condensing with maximum gradient of 10% per hour.
(2) 11 msec pulse width 1/2 sine wave.
Receiving Frame
Carrier
Physical Specifications
1.52” (38.6mm)
1.61” (40.9mm)
Height
Width
Depth
Weight
4.73” (120.1mm)
7.94” (201.7mm)
5.81” (147.6mm)
8.61” (218.7mm)
1.4lb (0.64kg) (1)
1.3lb (0.59kg)
(1) With carrier removed.
Electrical Specifications
Chassis Reliability/Maintainability
MTBF
500,000 Hours
5 minutes
+5V
+12V
65mA
Input
MTTR
400mA
Preventive
Maintenance
None
0832B
Insertion Rating
35,000
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
Appendix A - Specifications/Dimensions
17
Receiving Frame
with Carrier
Installed
2.06
(52.3mm)
3.12
(79.2mm)
1.61
(40.9mm)
0.47 (11.9mm)
5.81
(147.6mm)
8.614
(218.80mm)
3.12
(79.2mm)
Carrier
Only
1.52
(38.6mm)
4.73
(120.1mm)
7.939
(201.65mm)
3.75
(95.3mm)
0838D
4.081
(103.66mm)
1.75
(44.5mm)
Figure A-1: SATA DE110 Physical Dimensions
(Dimensions are for reference only)
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
18
Appendix B - Optional Accessories
Appendix B - Optional Accessories
Carrying Case
320FW_13
Figure B-1: Carrying Case
The optional molded plastic carrying case is designed to transport one (1) DE110 carrier from
one site to another in a safe, impact and moisture-resistant environmentꢀ Its compact
dimensions, 10” long x 11” wide x 4ꢀ5” high, make it easy to carry and to storeꢀ The foam lining
is contoured to fit a single Data Express carrierꢀ Contact your StorCase dealer for further
details and ordering informationꢀ
StorCase Technology, Incꢀ
SATA DE110 User's Guide - Revꢀ A03
Reader's Comments
19
Reader's Comments
Please take a few moments when your computer system is up and running to send us your
ideas and suggestions for improving our products and documentationꢀ Did the installation go
smoothly for you? Are there any changes you would like us to make, either with the hardware
itself, or with the installation instructions? Everyone at StorCase Technology is working
toward the goal of providing you with the highest quality, most cost effective, products
available on the market, and we need your comments to guide our effortsꢀ We look forward
to hearing from you soon!
Date:
Your Name:
Address:
Telephone: (
)
To mail this page, carefully remove it from the manual, fold it, staple or tape it shut, and drop
it in the mailꢀ To FAX this page, carefully remove it from the manual (or make a photocopy) and
FAX it to us at (714) 438-1847ꢀ Thank you for taking the time to help us make our products
better!
SATA DE110 User's Guide - Revꢀ A03
StorCase Technology, Incꢀ
FOLD ALONG THIS LINE AND STAPLE SHUT
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL
FIRST CLASS MAIL PERMIT NO. 10686 SANTA ANA, CA
POSTAGE WILL BE PAID BY ADDRESSEE
17600 NEWHOPE STREET
FOUNTAIN VALLEY CA 92708-9885
|