Sunbeam Electric Heater HE4900 User Manual

Euro Plus  
2400W Convection  
Panel Heater  
Instruction Booklet  
HE4900  
Please read these instructions carefully  
and retain for future reference.  
 
Contents  
Sunbeam’s Safety Precautions  
Safety Precautions for your heater  
Sunbeam’s Total Safety System  
1
2
3
Features of your Euro Plus Convection  
Panel Heater  
4
6
7
8
8
9
9
Wall mounting your heater  
Attaching the wheels  
Using your heater  
Restricting the temperature range  
Resetting the safety auto shut off  
Care and cleaning  
 
Sunbeam’s Safety Precautions  
Sunbeam are very safety conscious when  
• Do not use an appliance for any purpose  
other than its intended use.  
designing and manufacturing consumer products,  
but it is essential that the product user also  
exercise care when using an electrical appliance.  
Listed below are precautions which are essential  
for the safe use of an electrical appliance:  
• Do not place an appliance on or near a hot gas  
flame, electric element or on a heated oven.  
Do not place on top of any other appliance.  
• Do not let the power cord of an appliance hang  
over the edge of a table or bench top or touch  
any hot surface.  
• Read carefully and save all the instructions  
provided with an appliance.  
• Always turn the power off at the power outlet  
before you insert or remove a plug. Remove  
by grasping the plug - do not pull on the cord.  
• For safety reasons and to avoid maintenance  
by unskilled persons, some appliances are  
‘sealed’ using tamperproof screws. Such  
appliances should always be returned to the  
nearest Sunbeam Appointed Service Centre  
for adjustment or repair if required.  
Turn the power off and remove the plug  
when the appliance is not in use and  
before cleaning.  
• Do not use your appliance with an extension  
cord unless this cord has been checked  
and tested by a qualified technician or  
service person.  
• Do not operate any electrical appliance with a  
damaged cord or after the appliance has been  
dropped or damaged in any manner. If damage  
is suspected, return the appliance to the  
nearest Sunbeam Appointed Service Centre  
for examination, repair or adjustment.  
• Always use your appliance from a power  
outlet of the voltage (A.C. only) marked  
on the appliance.  
• For additional protection, Sunbeam  
recommend the use of a residual current  
device (RCD) with a tripping current not  
exceeding 30mA in the electrical circuit  
supplying power to your appliances.  
• Close supervision is necessary when your  
appliance is being used near children or  
infirm persons.  
• Never leave an appliance unattended while  
in use.  
• Do not immerse the appliance in water  
or any other liquid unless recommended.  
• Young children should be supervised to ensure  
that they do not play with the appliance.  
If you have any concerns regarding the performance and use of your appliance,  
Ensure the above safety precautions are understood.  
2
 
Sunbeam’s Safety Precautions  
• This heater becomes hot during use. To avoid  
burns, do not let bare skin touch hot surfaces.  
If provided, use handles when moving this  
heater. Keep combustible materials such as  
furniture, pillows, bedding, papers, clothes and  
curtains at least 3 feet (90cm) away from the  
front of the heater and keep them away from  
the sides and rear.  
• Do not locate the heater immediately below a  
socket outlet.  
• Do not use this heater in the immediate  
surrounds of a bath, shower, laundry area or  
swimming pool.  
• Do not insert or allow foreign objects to enter  
any ventilation or exhaust openings as this may  
cause electric shock or fire, or damage to the  
heater.  
• Extreme caution is necessary when any heater  
is used by or near children or invalids and  
whenever the heater is left unattended.  
To prevent a possible fire, do not block air  
intakes or exhaust in any manner. Do not use  
on soft surfaces, such as beds, where opening  
may become blocked.  
• Always unplug the heater when not in use.  
• Do not use outdoors.  
• Do not run the cord of the heater under  
carpeting. Do not cover the cord with throw  
rugs, runners or other floor coverings. Arrange  
the cord away from traffic areas where it will  
not be tripped over.  
• A heater has hot and arcing or sparing parts  
inside. Do not use it in areas where petrol,  
paint or flammable liquids are used or stored.  
Important instructions – retain for  
future use.  
If you have any concerns regarding the performance and use of your appliance,  
Ensure the above safety precautions are understood.  
3
 
Features of your Euro Plus heater  
Patented SCHWARZ element  
The patented heating element is designed to  
heat faster than conventional elements. Its  
single metal construction ensures optimum  
heat transfer from the element into the  
surrounding air, to warm the room faster.  
Overheat protection  
The safety auto shut off system  
detects any abnormally high  
temperatures within the heater and  
automatically switches it off to  
prevent overheating.  
4
 
Thermostat dial  
The thermostat dial allows you to set  
your desired temperature level.  
Accurate to within 1°C, the  
electromechanical thermostat monitors  
the room’s temperature and  
continuously adjusts the heat output to  
maintain your selected comfort level.  
The element is only powered for as long  
as necessary to restore the selected  
temperature, ensuring maximum  
efficiency.  
On/off switch  
The on/off switch at the side of the unit  
control’s the heater’s operation.  
Wall mount bracket  
The wall mount bracket is simply  
screwed onto the wall for quick and  
easy installation.  
5
 
Wall mounting your heater  
Before using your Euro Plus heater ensure it  
is securely mounted on a wall.  
Wall mounting  
For maximum efficiency this heater should  
be positioned so that the heat generated  
mixes with the maximum volume of air. It  
can be installed in any room of the home,  
including the bathroom, in accordance with  
the instructions below.  
A
A = 10 cm  
B = 10 cm  
C = 75 cm  
1. Remove the wall mounting bracket from  
the rear of the heater by squeezing the  
clips (at A and B in figure 2 below) and  
pulling towards you.  
Figure 3  
Note: any electrical appliances to be fitted in  
a bathroom should be installed by a qualified  
electrician in accordance with Australian/New  
Zealand Standard Wiring Rules. Portable  
heaters should not be used in a bathroom.  
B
A
Heaters that can be permanently fixed must  
be installed so that any controls cannot be  
reached by a person using a bath or shower,  
as shown in figure 4.  
Figure 2  
2. Select a suitable location to mount the  
heater, ensuring that it is at least 10cm  
below any curtains or window furnishings,  
10cm from any furniture located to either  
side, and 75cm from any furniture placed  
in front of the heater, as shown in figure 3.  
60cm  
60cm  
Figure 4  
The heater must be mounted horizontally,  
with the control panel at the top.  
6
 
Wall mounting your heater (continued)  
3. Mark the first top screw location on the  
wall, at least 630mm from the floor or  
skirting board. The base of the heater  
must be at least 200mm from the floor to  
ensure adequate air flow into the air inlet.  
Drill the first hole using a suitable drill bit.  
7. To place the heater on the bracket, insert  
the lower clips first then the top, and push  
firmly until it clicks into position, as  
shown in figure 5.  
4. Measure and mark the second drill hole,  
564mm from the first hole. Drill the hole.  
5. Measure and mark the bottom screw holes,  
289mm below the top two holes. Drill.  
6. Position the bracket over the drill holes  
and screw into position.  
Figure 5  
Attaching the wheels  
Before attaching the wheels, remove the wall  
mounting bracket from the rear of the heater  
by pushing down on the top clips and pulling  
towards you.  
Figure 6  
A
B
1. Position the wheel assembly over the base  
of the heater, with the vertical bracket to  
the rear of the unit, as shown in Figure 6.  
2. Align the screw hole in the vertical bracket  
(C) with the screw hole in the rear of the  
heater. Place the washer on the screw,  
insert the screw and fix loosely. Do not  
tighten.  
C
3. Align the screw holes on the underside of  
Once all screws are correctly positioned,  
tighten the screw in position C.  
the wheel assembly (A and B) with the  
holes on the base of the heater. Insert  
each screw and washer and tighten.  
4. Repeat on the other side.  
7
 
Using your heater  
1. Install the heater in accordance with the  
instructions above.  
5. Adjust the thermostat dial to your desired  
heat level, from 1 to 12.  
2. Insert the plug into a 230-240V power  
outlet and turn the power on.  
6. Once the selected temperature is reached,  
the electromechanical thermostat will  
constantly monitor the room temperature  
and adjust the heat output to maintain it.  
3. Ensure that the air inlet vent on the  
underside of the heater and the air outlet  
are clear of obstructions.  
7. To switch the heater off, move the on/off  
switch to the off position (O).  
4. Move the on/off switch to the on position (I).  
Restricting the temperature range  
With the aid of two pins at the back of the  
unit, you can limit the range of the  
2. Insert the pins in the desired position to  
limit or fix the rotation of the thermostat  
dial as desired.  
thermostat dial. Use one pin to lock the  
thermostat at a fixed temperature, or two  
pins to fix a set temperature range. One pin  
determines the upper value, and the other  
determines the lower value.  
1. To remove the pins from their original  
position, move each one back and forth  
using a pair of needle nose pliers to loosen  
them.  
Figure 7  
8
 
Resetting the safety auto shut off  
The safety auto shut off detects any  
abnormally high temperatures within the  
heater and shuts it off to prevent  
overheating. Should the safety auto shut  
off activate and switch off the heater, it  
will need to be reset.  
2.Unplug the heater and wait 5-10 minutes  
for the unit to cool down.  
3.After 5-10 minutes, plug the heater in  
again and operate as usual.  
1.To reset the heater, move the on/off switch  
to the OFF position.  
Care and cleaning  
Ensure that the heater is switched off and  
disconnected from the power outlet before  
cleaning.  
wiping with a damp cloth, or carefully going  
across the vent with a vacuum cleaner with  
brush attachment.  
Carefully wipe the exterior of the heater with  
a soft damp cloth and dry thoroughly with a  
dry cloth.  
Do not use harsh or abrasive cleaners to  
clean your heater, as these will damage the  
surface.  
Over time dust may accumulate on the front  
vent of the heater, this can be removed by  
is a registered trademark of Sunbeam  
Corporation Limited.  
© Copyright. SUNBEAM CORPORATION LIMITED 2004.  
(INCORPORATED IN N.S.W.) A.C.N. 000 006 771  
Sunbeam Corporation is a division of GUD Holdings Ltd.  
Euro Plus is a trademark of Sunbeam Corporation Limited.  
For more information or advice on this or any other  
Sunbeam appliance, visit www.sunbeam.com.au or  
contact the Sunbeam Consumer Service Line.  
Made in France. Due to minor changes in design or  
otherwise, the product you buy may differ from the one  
shown in this leaflet.  
Australia 1800 025 059  
New Zealand (09) 912 0747.  
Backed by Sunbeam‘s 3 Year Replacement Guarantee and  
National Service Network.  
9
 
Consumer Hotline  
Australia  
1800 025 059  
New Zealand  
(09) 912 0747  
Consumer information:  
is a registered Trademark of Sunbeam  
Corporation Limited. ACN 000 006 771.  
© Sunbeam Corporation Limited 2002.  
 

Sharp Portable Generator IG A10U User Manual
Shure Headphones GLXD14 User Manual
Sony Camera Lens SAL1118 User Manual
Sony CD Player CDP C360Z User Manual
Sony Computer Monitor SDM M81 User Manual
Sony Ericsson VCR NSP 1 User Manual
Sony Portable CD Player WM EX570 User Manual
Star Micronics Network Card TCP400 Series User Manual
Sun Microsystems Network Card LSI22320 SR User Manual
Sylvania Flat Panel Television 6842PE M User Manual