VARIABLE TEMPERATURE KETTLE
Instruction Booklet
Please read these instructions carefully and retain for future reference
KE9600
Contents
Sunbeam’s Safety Precautions
Congratulations
Features of your Café Series
1
2
®
Variable Temperature Kettle
Using your Café Series
3
®
Variable Temperature Kettle
Tea Brewing Styles and Tips
Sunbeam’s 3-Way Safety System
Care and Cleaning
5
7
8
9
Important instructions – retain for
future use.
Sunbeam’s Safety Precautions
SAFETY PRECAUTIONS FOR YOUR
SUNBEAM KETTLE.
• Boiling water will scald. Do not leave a boiling
or hot kettle near or where children
may touch it.
• Do not move kettle while switched on.
• Always turn the power off and unplug the cord
while the kettle is NOT in use.
• Do not operate the kettle without water.
®
• Your Café Series Variable Temperature Kettle
• Boiling water may be ejected, if overfilled.
must only be used with the power base
supplied.
• Always operate the kettle on a flat,
level surface.
• Do not leave the power cord near the edge
of a bench top where children may touch
or pull it.
Sunbeam is very safety conscious when designing
and manufacturing consumer products, but it is
essential that the product user also exercise care
when using an electrical appliance. Listed below are
precautions which are essential for the safe use of
an electrical appliance:
• Do not use an appliance for any purpose other
than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch any
hot surface.
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove by
grasping the plug - do not pull on the cord.
• Do not operate any electrical appliance with a
damaged cord or after the appliance has been
damaged in any manner. If damage is suspected,
return the appliance to the nearest Sunbeam
Appointed Service Centre for examination, repair
or adjustment.
• Turn the power off and remove the plug when the
appliance is not in use and before cleaning.
• Do not use your appliance with an extension cord
unless this cord has been checked and tested by
a qualified technician or service person.
• For additional protection, Sunbeam recommend
the use of a residual current device (RCD)
with a tripping current not exceeding 30mA in
the electrical circuit supplying power to your
appliances.
• Always use your appliance from a power outlet of
the voltage (A.C. only) marked on the appliance.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory • Do not immerse the appliance in water or any
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
other liquid unless recommended.
• Appliances are not intended to be operated by
means of an external timer or separate remote
control system.
• Children should be supervised to ensure that they
do not play with the appliance.
• This appliance is intended to be used in
household and similar applications such as: staff
kitchen areas in shops, offices and other working
environments; farm houses; by clients in hotels,
motels and other residential type environments;
bed and breakfast type environments.
• The temperature of accessible surfaces may be
high when the appliance is operating or when the
heating cycle has finished
• Never leave an appliance unattended while in use.
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
1
Congratulations
Congratulations on the purchase of your
Sunbeam Café Series Variable Temperature
Kettle
Uncompromising blends of stainless steel,
brass and die-cast alloy characterise the
range. This combined with advanced
technology and functional design, guarantee
the performance, that each product will
surpass expectations.
®
®
The Sunbeam Café Series delivers quality,
style and superior performance capturing
the essence of the commercial kitchen.
Inspired by heavy-duty equipment found in
restaurants, cafes and bars, the Sunbeam
®
The Sunbeam Café Series Variable
Temperature Kettle is designed with quality
stainless steel components and includes
many features that will help you brew the
perfect cup of tea.
®
Café Series is built to last. It brings together
a range of appliances designed to expertly
create authentic café food and beverages at
home.
2
®
Features of your Cafe Series
Variable Temperature Kettle
Stylish stainless steel design
Long life stainless steel with a premium
brushed and polished finish delivers quality
and style to suit any kitchen décor.
2400 watt concealed element
The fast boil 2400 watt element is concealed
in the base of the kettle for longer element
life. The smooth stainless floor reduces scale
build up and allows for easy cleaning.
Twin water level gauges
Full length water gauge indicates the volume
of water in the kettle up to 1.8L. The two
gauges make the kettle convenient to use for
both left and right handed users.
360 degree cordless power base
Designed to allow you to place the kettle
on the base in any direction. Convenient
for both left and right handed users.
Cord storage facility
Excess cord can be wound around the cord
storage facility underneath the power base.
Removable mesh filter
Keeps the water clean of any foreign matter
and is removable for easy cleaning.
3
3-Way Safety System
1 – Automatically switches the kettle off after boiling.
2 – Cuts out for boil-dry protection.
3 – Shuts down in case of an electrical fault.
Hinged locking lid
For ease of use the lid is activated by a
single press of a button. The design is ideal
for one-handed filling and also locks shut to
prevent accidental scalding.
Power base with LCD display panel
The LCD screen displays the current
temperature and the selected temperature.
When the heating cycle is in progress it also
displays the amount of time remaining (in
minutes and seconds) before the selected
temperature is reached.
START / CANCEL
Once the desired temperature has been
selected the START/CANCEL button initiates
the heating cycle.
It is also a quick start function. If the
START/CANCEL button is pressed before a
temperature is selected, the previous settings
are initiated.
Temp
Enables the user to select from 5 different
temperatures; 80°C, 85°C, 90°C, 95°C and
100°C (boil).
Keep warm feature
Convenient Keep Warm feature allows
you to maintain the selected water
temperature for up to 20 minutes.
4
®
Using your Cafe Series Variable
Temperature Kettle
®
Before using your kettle.
Using your Cafe Series Variable Temperature
Kettle
It is recommended that you clean your kettle
before using it by filling the kettle with water
to the maximum level indicator, boiling the
water and discarding.
Tip: The Variable Temperature Kettle has five
optimum tea temperatures you can select
from: 80°C, 85°C, 90°C, 95°C and 100°C
(boil). Refer to the ‘Tea Brewing Styles and
Tips’ table on page 8 for the ideal water
temperature for your tea.
Important: Do not fill the kettle over the
maximum level, as water may spill out of the
spout when boiling.
Note: The temperature settings are a guide
only and may vary depending on personal
preference.
1.Press the ‘TEMP’ button to select from five
pre-set temperatures: 80°C, 85°C, 90°C,
95°C and 100°C (boil). Your selected
water temperature will be displayed on the
LCD display for 3 seconds. Press ‘START/
CANCEL’ to initiate the heating cycle.
1.To fill the kettle, remove it from the power
base and lift the lid, by pressing the button
at the top of the handle. Do not fill the
kettle below the 'min' indication.
2.Fill the kettle with the desired amount of
water. Always fill the kettle between the
minimum and maximum marks. Too little
water will result in the kettle switching off
before the water has boiled.
Note: If after 3 seconds nothing is pressed,
the LCD display will revert back to showing
the current water temperature.
Note: If the START/CANCEL button is pressed
without any temperatures being selected
beforehand, it will automatically default to
the last used setting. The START/CANCEL
button is originally preset to 100°C (boil).
3.Push the lid closed firmly until it locks into
position.
4.Place the kettle onto the power base. Plug
the power cord into a 230-240 Volt AC
power outlet and switch the power on.
Note: If the kettle is not positioned on top of
the power base correctly the LCD panel will
show “--:---“.
2.When the heating cycle is initiated, the
LCD display will show the maximum
amount of time required to reach the
selected water temperature. The Time to
Boil feature shown on the LCD display will
count down and flash until the correct
time is calculated. Once the correct time
is calculated the Time to Boil recalibrates
to the correct time remaining and will no
longer flash.
5
®
Using your Cafe Series Variable Temperature Kettle continued
Note: The maximum amount of time is
dependent on the ambient temperature
of the water. The colder the initial water
temperature the longer the heating cycle.
For example, if the initial temperature is
20°C the time to boil feature will show a
maximum time of 5min 24 seconds.
3. During the heating cycle the TEMP button
will flash and the START/CANCEL button
will be illuminated. The LCD panel will
display the increasing temperature and the
number of minutes and seconds remaining
until the selected temperature is reached
4. The kettle will beep once when the
selected water temperature has been
reached.
Note: To cancel the heating process at any
time during the boiling cycle, simply press
the ‘START/CANCEL’ button once.
Time to Boil Feature
The Time to Boil feature calculates the
amount of time remaining until the selected
water temperature is reached.
Note: Water does not boil evenly and the
amount of time it takes to boil is dependent
on factors such as the volume of water,
the ambient temperature, levels of mineral
content and the selected temperature.
Therefore, the Time to Boil is a guide only
and is not scientifically exact.
When the heating cycle is initiated, the LCD
display will show the maximum amount of
time required to reach the selected water
temperature. The Time to Boil shown on the
LCD display will count down and flash until
the correct amount of time is calculated.
Once the correct time is calculated the
Time to Boil may jump to the correct time
remaining and will no longer flash.
Note: The Time to Boil feature does not
calculate the remaining time before the
temperature is reached when the initial
temperature is 75ºC and above.
Note: If the kettle is removed from the power
base during the heating process, the kettle
will automatically reset, cancelling the
heating cycle. However, when the kettle is
replaced the Keep Warm function will remain
illuminated if it was previously selected..
6
®
Using your Cafe Series Variable Temperature Kettle continued
Keep Warm Function
Sleep mode
1.To maintain the temperature of the
selected water temperature, simply press
the ‘KEEP WARM’ button. This will maintain
the temperature selected for up to 20
minutes. The ‘KEEP WARM’ button will
remain illuminated to indicate that it has
been selected.
The kettle will automatically switch off the
LCD screen after 20 minutes to save power.
To exit the standby mode, press any button.
Note: If START/CANCEL is selected during
Sleep Mode, the kettle will automatically
initiate the previous settings (including
temperature and Keep Warm).
Figure 1
Note: The ‘KEEP WARM’ button can be
pressed when selecting your desired water
temperature or after the power START/
CANCEL button has been pressed (during the
boiling cycle). It will then continue to flash
during the heating cycle and will remain
illuminated during the keep warm period.
The ‘KEEP WARM’ button will illuminate to
indicate that it has been selected.
Note: If the ‘KEEP WARM’ button is selected
when the 100°C (boil) temperature has been
selected, the kettle will boil to 100°C and
maintain at 100°C for up to 20 minutes.
Note: If the kettle is removed from the power
base during the keep warm period, the kettle
will automatically resume the keep warm
period at the set temperature when the kettle
is replaced
Note: During the heating cycle, the LCD
display panel will remain illuminated,
showing the temperature of the kettle as
it increases and also the amount of time
left before the kettle reaches the selected
termperature.
7
Tea Brewing Styles and Tips
Optimum Tea Temperatures
The Variable Temperature Kettle has five optimum tea brewing temperatures 80°C, 85°C,
90°C, 95°C and 100°C (boil). Refer to the table below for Sunbeam’s recommended
temperature for a range of tea varieties:
OPTIMUM TEA TEMPERATURES
Asatsutu
Bancha
Ceylon Green
China Chun
Mee
Apple
China Rose
Darjeeling
Earl Grey
Ensemble
Indian Chai
Irish
Breakfast
Keeman
Pouchong
Ti Kuan Yin
Wuyi
Assam
Chai
Blackcurrant
China Yin Zhen
Elderflower
Ginger
Lemon
Lychee
Orange
Peony
Silver
Needle
Chamomile
Cinnamon
Herbal
Lemongrass
Peppermint
Rooibos
Green
Dragon Well
Fukamushi
Sencha
Gunpowder
Gyokuro
Jasmine
Kukicha
Nepal Green
Pi Lo Chun
Sencha
Spearmint
Snowbud
Strawberry
Instant Coffee
Plunger Coffee
Tencha
Brew Strength and Time
The brew strength preference will vary from individual to individual, however we have provided
below some suggested brew times dependant on how strong you like the flavour of your tea.
Note: Certain teas should not be brewed for
more than 3 minutes, including certain green
teas, white teas and oolong teas.
We recommend you read the packaging of
your purchased tea variety for more detailed
brewing instructions.
MILD
3 minutes
4 minutes
5 minutes
MEDIUM
STRONG
NOTE: These two tables are recommendations only and may vary depending on personal
preference, brand and age of tea/coffee used.
8
Sunbeam’s 3-Way
Safety System
Safety is a major consideration in the design
of a Sunbeam kettle. This is why we have
developed our 3-Way Safety System, which
ensures that your kettle will:
3.Shut-down in case of overheating.
In the event of overheating, the kettle will
automatically shut down to prevent further
damage. Should this occur, take your kettle
to a Sunbeam Service Centre or Appointed
Service Agent.
1.Automatically switch off after boiling.
For convenience, safety and energy
efficiency, your Sunbeam kettle will
automatically switch off after boiling.
2.Cut-out for boil-dry protection.
If the kettle is operated without water, it
will automatically cut-out, preventing any
damage to the element.
If this occurs, allow the kettle to cool
before filling with cold water and
re-boiling.
9
Care and Cleaning
Always disconnect the kettle from the power
outlet before cleaning.
Never immerse the kettle switch area, cord
or power base in water, or allow moisture to
come into contact with these parts.
To clean the stainless exterior
The stainless steel surface may be wiped over
with a damp cloth and polished with a soft
dry cloth.
CAUTION: Do not use chemicals, steelwool,
or abrasive cleaners to clean the outside of
the kettle, as these will scratch the stainless
steel surface.
Descale Your Kettle Regularly
Mineral deposits in tap water solidify when
the water is heated; lime scale may be white,
coloured, even rusty-looking and is normally
visible but phosphate scale isn’t generally
visible although may cause the water to
appear cloudy when heated. This may cause
the interior of the water gauge to discolour,
cause overheating, trigger the boil-dry cut-out
mechanism or even reduce the kettle’s life.
To clean the mesh filter
Press the button on the handle to open
the hinged lid. Grasp the top of the mesh
filter and pull upwards to remove. Wash in
warm soapy water and dry thoroughly before
replacing in the kettle.
Even in soft water areas it is important
to descale your kettle regularly to help
maintains its lifecyle.
To remove this build-up, use Sunbeam Liquid
Descaler, a simple to use, non-toxic cleaner
available from Sunbeam Appointed Service
Agents.
Alternatively:
1.Fill the kettle with 3 cups of white vinegar
and the remainder with water and allow to
stand overnight. DO NOT BOIL.
2.Empty the solution from the kettle. Any
stains remaining inside the spout can be
removed by rubbing with a damp cloth. Fill
the kettle with clean water, bring to boil
and then discard the water. Repeat and the
kettle will then be ready to use.
10
The Sunbeam
2 Year Element
Guarantee
Sunbeam has built its reputation
on manufacturing quality electrical
appliances. Our Cafe Series® Variable
Temperature Kettle is constructed from
the highest quality materials. So much
so, we guarantee our Kettle element for
(2) two years against faulty materials
or manufacture. This guarantee is just
another expression of our confidence in
the way we make appliances at Sunbeam.
In order to be eligible for this guarantee,
you must retain your receipt as proof of
purchase.
If a fault should develop with the element
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to
the appliance.
after the period covered by the 12 Month
Replacement Guarantee, please call
Sunbeam Customer Service on the number
listed below or send a written claim to
Sunbeam at the address listed below.
On receipt of your claim, Sunbeam will
advise you on how to obtain a replacement
element if your element is defective.
Alternatively, you can return the Cafe
Series® Variable Temperature Kettle to any
of Sunbeam’s authorised service centres,
together with your receipt. The service
centre will examine the element and if it
is faulty or defective, the element will be
replaced free of charge.
Our goods come with guarantees that
cannot be excluded under the Australian
Consumer Law and under the New Zealand
Consumer Guarantees Act. In Australia you
are entitled to a replacement or refund for
a major failure and for compensation for
any other reasonably foreseeable loss or
damage. You are also entitled to have the
goods repaired or replaced if the goods fail
to be of acceptable quality and the failure
does not amount to a major failure.
Your Cafe Series® Variable Temperature
Kettle is covered for the first year against
faulty material or manufacture by
the Sunbeam 12 Month Replacement
Guarantee. Should you experience any
difficulties with your appliance within
this 12 Month period, please phone our
customer service line for advice on 1300
881 861 in Australia, or 0800 786 232 in
New Zealand.
IMPORTANT NOTE
For a complete list of Sunbeam’s authorised
service centres visit our website or call:
Sunbeam agrees to replace the element in
the event of the element developing a fault
or defect, within the one year after the
12 Month Replacement Guarantee.
Sunbeam Corporation Ltd.
Australia
As your Cafe Series® Variable Temperature
Kettle needs to be assessed at a Sunbeam
authorised service centre, it will not be
accepted through retail stores.
1300 881 861
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
The Sunbeam (2) two year element
guarantee begins from date of purchase
and extends for one year beyond the 12
Month Replacement Guarantee. It covers
only the element, guaranteeing it against
faulty materials or manufacture. It does
not cover damage caused by accident,
misuse or being used in a manner not
in accordance with the Instruction Book.
Similarly, this element guarantee does not
cover freight or any other costs incurred in
making a claim.
If using the Cafe Series® Variable
Temperature Kettle for commercial use this
element guarantee is limited to 12 months
from the date of purchase.
Sunbeam Corporation Ltd.
New Zealand
0800 786 232
26 Vestey Drive, Mt Wellington
Auckland, New Zealand
12 Month Replacement Guarantee
In the unlikely event that this appliance develops any malfunction
within 12 months of purchase (3 months commercial use) due
to faulty materials or manufacture, we will replace it for you free
of charge.
Should you experience any difficulties with
your appliance, please phone our customer
service line for advice on 1300 881 861 in
Australia, or 0800 786 232 in New Zealand.
Alternatively, you can send a written claim
to Sunbeam at the address listed below.
On receipt of your claim, Sunbeam will
seek to resolve your difficulties or, if the
appliance is defective, advise you on how
to obtain a replacement or refund.
In Australia you are entitled to a
replacement or refund for a major failure and
for compensation for any other reasonably
foreseeable loss or damage. You are also
entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to
a major failure.
Should your appliance require repair or
service after the guarantee period, contact
your nearest Sunbeam service centre.
Your Sunbeam 12 Month Replacement
Guarantee naturally does not cover misuse
or negligent handling and normal wear and
tear.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:
Australia
Similarly your 12 Month Replacement
Guarantee does not cover freight or any other
costs incurred in making a claim. Please
retain your receipt as proof of purchase.
1300 881 861
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to the
appliance.
New Zealand
0800 786 232
26 Vestey Drive, Mt Wellington
Auckland, New Zealand
Our goods come with guarantees that cannot
be excluded under the Australian Consumer
Law and under the New Zealand Consumer
Guarantees Act.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Or call 1300 881 861
In New Zealand
Or call 0800 786 232
is a registered trademark.
Cafe Series’ logo and words are registered trademarks of
Sunbeam Corporation.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright. Sunbeam Corporation Limited 2006.
ABN 45 000 006 771
Sunbeam Corporation is a division of GUD Holdings Ltd.
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Unit 3, Building D
26 Vestey Drive
Mt Wellington Auckland
New Zealand
03/12
|