™
Carveasy
Electric Knife
Instruction Booklet
This book covers the use and care of the following Sunbeam Electric Knives:
™
EK3800 Sunbeam Carveasy
™
EK5600 Sunbeam Carveasy Pro
Please read these instructions carefully
and retain for future reference.
EK5600
EK3800
Sunbeam’s Safety Precautions
SAFETY PRECAUTIONS FOR YOUR
SUNBEAM ELECTRIC KNIFE.
• Serrated edges of the blades are very sharp.
• Do not allow children to play with blades.
• Caution is necessary when handling the blades.
Sunbeam is very safety conscious when
designing and manufacturing consumer products,
but it is essential that the product user also
exercise care when using an electrical appliance.
Listed below are precautions which are essential
for the safe use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and
before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Appliances are not intended to be operated
by means of an external timer or separate
remote control system.
• This appliance is intended to be used in
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels and other residential
type environments; bed and breakfast type
environments.
• Children should be supervised to ensure that
they do not play with the appliance.
• The temperature of accessible surfaces may be
high when the appliance is operating.
• Never leave an appliance unattended while
in use.
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
1
Features of your Sunbeam
™
Carveasy Pro
Blade release button
Soft touch ergonomic handle
Extra long stainless steel blades
Double movement
safety trigger
Neon power light
Handy hang up loop
EK5600 Pictured
Micro serrated stainless steel blades
Handle
Serrated stainless steel blades are durable
and sharp for efficient slicing and carving.
Convenient and simple to operate. The
ergonomic design provides comfort, versatility
and control when carving both vertically and
horizontally.
Blade release button
Conveniently located at the top of the handle
for thumb action release of the stainless steel
blades.
Handy hang up loop
The handy hang-up loop enables the product
to be stored conveniently for easy access any
time.
Double movement safety trigger
Located under the handle for ease of
operation, the index-finger trigger action,
allowing the most comfortable position for
carving. The double movement trigger system
provides added safety.
Safety guards
For safe fitting and removal of blades
Neon power light
The neon power light indicates when the
Carveasy Pro™ is plugged in and switched on.
2
Features of your Sunbeam
™
Carveasy
Blade release button
Soft touch ergonomic handle
Extra long stainless steel blades
Double movement
safety trigger
Neon power light
Handy hang up loop
EK3800 Pictured
Micro serrated stainless steel blades
Handle
Serrated stainless steel blades are durable
and sharp for efficient slicing and carving.
Convenient and simple to operate. The
ergonomic design provides comfort, versatility
and control when carving both vertically and
horizontally.
Blade release button
Conveniently located at the top of the handle
for thumb action release of the stainless steel
blades.
Handy hang up loop
The handy hang-up loop enables the product
to be stored conveniently for easy access any
time.
Double movement safety trigger
Located under the handle for ease of
operation, the index-finger trigger action,
allowing the most comfortable position for
carving. The double movement trigger system
provides added safety.
Safety guards
For safe fitting and removal of blades
Neon power light
The neon power light indicates when the
Carveasy™ is plugged in and switched on.
3
Using your Sunbeam Knife
1.Interlock blades together before inserting
into the appliance. To assemble blades,
grasp shaft ends below the safety guards
and slip the rivet on the tip of the other
blade. See Figure 1. Bring blades together
ensuring tips remain together.
under the handle to activate the motor.
Releasing the switch will automatically
stop the motor.
Warning: Avoid contact with moving parts.
Keep hands, hair, clothing and other utensils
away from moving blades during operation to
prevent personal injury and/or damage to the
knife.
Note: Always use both blades when operating
the Carveasy™ and the Carveasy™ Pro.
4.When slicing is completed, turn the power
off at the power outlet and remove the
plug. Slide back the Blade Release, hold
the blades by the safety guards with the
cutting edge facing downward and pull the
blades out of the slots. See Figure 3.
Figure 1
2.Hold assembled blades by the safety
guards and slide shafts gently into the
blade slot until clipped into position.
See Figure 2.
Warning: Only when blades are fitted should
the cord be connected to the
power outlet.
Figure 3
Warning: The blades of your Sunbeam
Carveasy™ and Carveasy™ Pro are sharp!
Handle with extreme care. We recommend
using the guard sleeve provided when
handling the blades. Do not fit or remove
blades whilst the knife is connected to
the power outlet. Do not allow children to
operate the appliance.
Figure 2
3.Insert the plug into a 230-240 volt (AC
only) power outlet and ensure the cord is
well away from the blades. Holding the
knife with one hand, slide and press the
double movement safety trigger positioned
4
Slicing Hints
Always place food to be sliced on a wooden
or plastic cutting board. Do not slice food
on china; metal or bench tops, as scratching
may occur. Guide blades through food.
A sawing action is not necessary. Do not
force blades through food. To maintain the
sharpness of blades, do not cut through
bones, fruit pips or stones or any other hard
substances.
Before carving meat or chicken, remove
skewers. If desired, string may be left around
the meat whilst carving. The use of a carving
fork to steady the meat assists in carving
straight, even slices. Do not attempt to
sharpen blades.
We recommend when slicing foods like bread,
a light smear of cooking oil, margarine or
similar, on the inside of the blades will
reduce the friction.
For best results when carving meat and
poultry allow cooked meat to stand for 10-15
minutes before slicing. this allows the juices
to set and makes carving easier and neater.
5
Care and Cleaning
pads or powders on blades. After cleaning,
always store blades in plastic sleeves. To
clean motor housing wipe with a soft damp
cloth.
Before storing your knife, a light smear of
cooking oil or similar on the inside of the
blade is suggested.
Warning: Ensure the unit is switched off
and the plug removed from the power outlet
before removing the blades and/or cleaning.
Unlock the blades by sliding apart. Always
hold blades by the shaft end, behind the
safety guard, when handling and cleaning.
Wash the blades in hot soapy water with a
soft cloth or sponge. Rinse thoroughly and
dry completely. Do not use abrasive scouring
6
Notes
Notes
12 Month Replacement Guarantee
In the unlikely event that this appliance develops any malfunction
within 12 months of purchase (3 months commercial use) due to
faulty materials or manufacture, we will replace it for you
free of charge.
Should you experience any difficulties with
your appliance, please phone our customer
service line for advice on 1300 881 861 in
Australia, or 0800 786 232 in New Zealand.
Alternatively, you can send a written claim
to Sunbeam at the address listed below.
On receipt of your claim, Sunbeam will
seek to resolve your difficulties or, if the
appliance is defective, advise you on how
to obtain a replacement or refund.
In Australia you are entitled to a
replacement or refund for a major failure and
for compensation for any other reasonably
foreseeable loss or damage. You are also
entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to
a major failure.
Should your appliance require repair or
service after the guarantee period, contact
your nearest Sunbeam service centre.
Your Sunbeam 12 Month Replacement
Guarantee naturally does not cover misuse
or negligent handling and normal wear and
tear.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:
Australia
Similarly your 12 Month Replacement
Guarantee does not cover freight or any other
costs incurred in making a claim. Please
retain your receipt as proof of purchase.
1300 881 861
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to the
appliance.
New Zealand
0800 786 232
26 Vestey Drive, Mt Wellington
Auckland, New Zealand
Our goods come with guarantees that cannot
be excluded under the Australian Consumer
Law and under the New Zealand Consumer
Guarantees Act.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Or call 1300 881 861
In New Zealand
Or call 0800 786 232
is a registered trademark.
‘Carveasy’ is a trademark of Sunbeam Corporation.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright. Sunbeam Corporation Limited 2011.
ABN 45 000 006 771
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Unit 3, Building D
26 Vestey Drive
Mt Wellington Auckland
New Zealand
Sunbeam Corporation is a division of GUD Holdings Ltd.
9/12
|