Pro Steam Irons
Instruction Booklet
This book covers the use and care of the following Sunbeam Irons:
SR4100 Pro Steam Polished shot and spray iron
SR4200 Pro Steam Teflon® shot and spray iron
SR4250 Pro Steam Teflon® shot and spray iron
SR4300 Pro Steam Teflon® shot and spray iron with Auto-off
Please read these instructions carefully
and retain for future reference.
Sunbeam’s Safety Precautions
SAFETY PRECAUTIONS FOR YOUR IRON
• Do not wind the cord around the soleplate
while the iron is still hot.
• Do not leave the iron unattended while it is
plugged into the power outlet.
• Do not leave a hot iron within reach of
children. If they come into contact with a hot
iron it could lead to serious burns.
• Iron only on an ironing board.
• Always unplug the iron from the power outlet
before filling or emptying the water tank.
• An iron takes approximately 30 minutes to cool
down. Allow the iron to cool completely before
storing.
Sunbeam is very safety conscious when
designing and manufacturing consumer products,
but it is essential that the product user also
exercise care when using an electrical appliance.
Listed below are precautions which are essential
for the safe use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and
before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Appliances are not intended to be operated
by means of an external timer or separate
remote control system.
• This appliance is intended to be used in
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels and other residential
type environments; bed and breakfast type
environments.
• Children should be supervised to ensure that
they do no play with the appliance.
• The temperature of accessible surfaces may be
high when the appliance is operating.
• Never leave an appliance unattended while
in use.
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
3
Features of your Sunbeam
Pro Steam Iron
Powerful shot of steam
Pressing the shot of steam button instantly
produces a powerful shot of steam to remove
stubborn wrinkles.
Vertical shot of steam
Pressing the shot of steam button with the iron
in an upright position produces a vertical shot
of steam, which is ideal for steaming curtains
and suits, and removing creases from delicate
fabrics.
Fine spray mist
Pressing the spray button provides a fine mist
spray to dampen hard-to-iron fabrics.
Easy-fill water inlet
The water inlet cover opens fully to allow easy
filling of the water tank, without bubbling or
spilling.
Large water tank
Holds 280ml of water for continual high steam
performance without having to refill the tank
regularly.
Full length button groove
For ironing around buttons.
Teflon® Select non-stick soleplate
Polished Aluminium soleplate (SR4100)
Durable polished aluminium soleplate
is hard-wearing and easy to clean.
(SR4200) & (SR4250)
Glides easily across all types of fabric and
prevents sticking.
4
Long cord with 360º cord outlet
The cord outlet is ideal for left or right
hand use, and provides greater versatility
and ease of movement when ironing. The
flexible grommet protects the cord from
fraying.
Safety auto-off (Model SR4300 only)
The iron automatically switches itself off
if left in the ironing position (horizontal)
for 30 seconds, or in the heel rest
position (vertical) for 15 minutes. (For
more information on the safety auto off
feature see page 7).
Thermostat light
Illuminates to indicate that the iron
is heating and goes out when it has
reached the selected temperature. The
thermostat light cycles on and off during
ironing as the iron maintains the selected
temperature.
Variable steam
The steam dial allows you to select the
desired steam output for each garment.
Alternatively, select the DRY setting to
iron without steam.
Temperature dial
Allows you to select the desired
temperature for each garment. The
adjustable temperature dial also indicates
the amount of steam recommended for
use on each temperature setting.
Stable heel rest
Large heel rest keeps the iron stable on
the ironing board.
Cord wrap facility
The built-in cord wrap facility allows you
to wind the cord around the heel for neat
and tidy storage of the cord when the iron
is not in use.
2100 watts for fast heat up
5
Using your Sunbeam Pro Steam Iron
Before first use
Using your iron
Remove any adhesive stickers, plastic covers
or cardboard sleeves from the soleplate.
Ensure that all adhesive is removed by
rubbing the soleplate with a cloth dampened
with methylated spirits.
Fill the water tank and empty the water. This
will rinse out any foreign particles remaining
in the water tank from the manufacturing
process.
1.Insert the plug into a 230/240 volt power
outlet and turn the power on.
2.Turn the temperature dial to the desired
setting by aligning the setting on the
dial with the temperature indicator. The
thermostat light (positioned on the top
of the handle) will illuminate to indicate
that the iron is heating to the selected
temperature. When the thermostat light
goes out the iron has reached the selected
temperature and is ready to iron.
NOTE: When turned on for the first time, your
new iron may give off vapours for up to 10
minutes. This is due to the initial heating of
the materials used. It is safe, not detrimental
to the performance of the iron, and will not
reoccur.
NOTE: When the temperature dial is changed
from a high setting to a lower temperature
setting during ironing, the thermostat light
will go out immediately. This indicates
that the iron is cooling to the selected
temperature. To ensure that the iron has
reached the selected temperature and is not
too hot, wait until the thermostat light comes
on again and then goes out before ironing.
Filling the iron with water
Before filling the iron with water ensure the
power is turned off and the plug is removed
from the power outlet. The iron can be filled
with water while it is hot.
Dry ironing
Follow steps 1 and 2 above.
Place the iron on its heel and open the water
inlet cover.
3.Select DRY on the steam dial. This will cut
off the steam flow if there is water in the
tank.
Slowly pour water into the water inlet until
the maximum water level is reached. Do not
exceed the maximum water level indicator.
Push the water inlet cover firmly to close.
Steam ironing
NOTE: The special soleplate design allows you
to use tap water with your Pro Steam iron
without affecting the steam performance.
However in very hard water areas, Sunbeam
recommends the use of distilled water, or
water which has been demineralised.
Follow steps 1 and 2 above.
NOTE: When steam ironing, ensure that the
temperature dial is set to any temperature
within the steam band and that the tank is at
least ¼ full of water.
3.Turn the steam dial to the desired steam
setting.
For best performance, we recommend the use
of Sunbeam Water Demineraliser, available
selected retailers. This will produce up to 30
litres of demineralised water.
Do not fill the iron with fabric conditioner,
starches or any other solution as these will
damage the steam mechanism. Do not use
contaminated water.
6
Using your Sunbeam Pro Steam Iron (continued)
Using the shot of steam
NOTE: If the tank has run dry, it may be
necessary to re-prime the pump after filling
the iron with water.
The shot of steam can be used whether dry
or steam ironing when the temperature dial
is set to any temperature above the two dot
(••) setting.
Using the spray mist
The spray mist can be used whether dry
or steam ironing to pre-dampen hard to
iron fabrics.
1. Ensure the tank is at least ¼ full of
water.
2. Select the desired temperature and wait
until the thermostat light goes out.
3. Press the shot of steam button several
times with the iron on the soleplate to
prime the pump.
1. Ensure the tank is at least ¼ full of
water.
2. Press the spray button during ironing
to release a fine mist from the spray
nozzle.
The safety auto-off feature
(Model SR4300 only)
The safety auto-off mechanism automatically
turns the iron off if you forget.
Once the iron is moved the power will
reconnect. Allow the iron to heat until the
thermostat light goes out, and continue
ironing as normal.
The iron will automatically shut off if left
on the heel rest (vertical) for 15 minutes,
or in the ironing position (horizontal) for 30
seconds, without being moved.
The thermostat light on the handle will flash
and a warning beep will sound to let you
know that you have left the iron unattended.
Power to the iron's heating element will be
cut.
15 minutes
30 seconds
7
Care and Cleaning
After each use
To clean the steam holes
To remove build up from the steam holes
which may affect steam performance, use
a cotton wool tip moistened in methylated
spirits.
1. Turn the power off and remove the plug
from the power outlet.
2.Allow the iron to cool before winding the
cord around the built-in cord wrap.
Cleaning the Teflon® Select non-stick soleplate
(SR4200 & SR4300)
The non-stick coating reduces sticking of
fabrics and starches to the soleplate. Do
not iron over sharp objects such as buttons,
studs and zippers, as these will scratch the
surface.
Storage
Always store the iron on its heel rest.
NOTE: Do not store the iron with the soleplate
facing down, or in the carton.
Cleaning
To clean the exterior of your iron, wipe over
with a damp soft cloth and wipe dry.
Wipe the soleplate with a damp soft cloth
after each use. If polyester has burnt to the
soleplate, iron a damp cotton cloth while hot.
Caution: Do not use harsh abrasives, chemical
cleaners or solvents to clean the exterior of
your iron as these will damage the surface.
Caution: Do not use scouring pads, abrasives
or harsh cleaners to clean your Teflon® Select
non-stick soleplate, as these may scratch and
damage the surface.
Cleaning the Polished Aluminium soleplate
(SR4100)
Rub gently with a stainless steel soap pad
moistened in warm water. Wipe dry.
8
Ironing Tips and Tricks
Tip # 27 - Iron shirts like a pro
Tip # 13 - Ironing the seam
Start with the collar, working from the outer
edges into the middle. Iron the shoulder
next, followed by the cuffs and sleeves. Place
the collar at the narrow end of the board so
that one front panel of the shirt is extended
flat. Iron the front panel from shoulder to
shirt tail. Rotate to iron the back of the shirt.
Rotate and complete the remaining front
panel.
Always press seams in the same direction
they were made. When a garment is
produced, the fibres will naturally settle
in the direction they were initially pressed,
so it’s best not to iron against the grain.
Tip # 26 - Sort types of fabric
Sort articles to be ironed according to the
type of fabric. This will reduce the need to
adjust the temperature constantly. Start with
articles requiring lower temperatures and
work your way through to items requiring
higher settings.
Tip # 34 - Tips for T-shirts
Straighten seams on t-shirts before hanging
out to dry. To avoid damage to printed
graphics and logos turn the t-shirt inside out
and iron the reverse side of the print. Never
iron areas of your t-shirt where perspiration
marks are visible as the heat of the iron will
permanently fix the stain.
Tip # 2 - Summer frocks and frills
Steam is the key when ironing delicate
summer fabrics such as muslin, cotton and
linen. Don’t press down with the iron, simply
hover above the garment and steam it using
a vertical shot of steam. Ruffling, netting,
tulle or intricate hand detailing is also best
ironed using this method.
Tip # 54 - Hung out to dry
When washing is complete, remove shirts
from the machine immediately, shake them
out and hang them on coat hangers to air dry
– this will keep wrinkles to a minimum.
Tip # 5 - Pressing your winter woollies
Steam is crucial when pressing your winter
woollies. Woollen garments can be hung and
steamed using the vertical shot of steam
feature. After steaming, brush the garment
with your hand to plump up woollen fibres.
If ironing the garment flat it is best to use
a pressing cloth. Don’t be afraid to apply
pressure – steam and hold.
Tip # 18 - Selecting the right temperature
If you are unsure of the correct setting for a
particular garment, test a small area such as
a seam or inside hem before ironing a visible
area. Start with a low temperature and slowly
increase the heat to find the best setting.
Tip # 33 - Don’t be afraid to iron silk
Tip # 42 - Table settings to impress
To avoid unwanted creases always iron
your table cloth after taking it out of the
cupboard. A dinner party is a special
occasion, so treat the table cloth as you
would your own outfit. For best results, lay
towels across your table and iron the table
cloth over the towels. This will save you time
and ensure a beautifully presented table
setting.
Don’t be afraid to iron silk. Although delicate
in appearance, silk is the strongest and most
resilient of all natural fibres. To achieve the
best results, set to a low cotton setting and
use regular shots of steam. Always use a
pressing cloth to avoid shine marks.
9
Ironing Chart
Fabric
Acrylic
Temp setting Ironing
Ironing recommendation
MINIMUM
Min to •
Dry iron on reverse side of fabric
MINIMUM
Min to •
Dry iron on reverse side of fabric
while still damp
Acetate
MINIMUM
Min to •
Nylon
Polyester
Rayon
Iron on reverse side of fabric
Iron on reverse side of fabric
Iron on reverse side of fabric
SYNTHETIC
•
SYNTHETIC
•
SYNTHETIC
•
Mainly dry iron. Steam can be used under
manufacturer's instructions
Viscose
Iron on reverse side of fabric. Use an ironing
cloth to prevent shine marks
SILK
• •
Silk
and use regular shots of steam
Check label and follow manufacturer’s
instructions. Use setting for the fibre
requiring the lowest setting
WOOL
• •
Cotton Blends
Wool
Steam iron on reverse side of fabric
or use an ironing cloth. Brush gently
to raise the fibres
WOOL
• •
Steam iron on reverse side of fabric
or use an ironing cloth. Brush gently
to raise the fibres
WOOL
• •
Wool Blends
Steam iron on reverse side of fabric
or use an ironing cloth. Brush gently
to raise the fibres
COTTON
• • •
Corduroy
Cotton
Steam iron while still damp or use spray
to dampen. Use medium to high steam
COTTON
• • •
Iron on reverse side of fabric or use an
ironing cloth to prevent shine marks,
especially with dark colours. Iron while
still damp or use spray to dampen.
Use medium to high steam
LINEN
• • • to Max
Linen
Iron while still damp or use spray
to dampen. Use maximum steam
MAXIMUM
• • • to Max
Denim
10
2 Year Replacement Guarantee
In the unlikely event that this appliance develops any malfunction
within 2 years of purchase (3 months commercial use) due to
faulty materials or manufacture, we will replace it for you
free of charge.
Should you experience any difficulties with
your appliance, please phone our customer
service line for advice on 1300 881 861 in
Australia, or 0800 786 232 in New Zealand.
Alternatively, you can send a written claim
to Sunbeam at the address listed below.
On receipt of your claim, Sunbeam will
seek to resolve your difficulties or, if the
appliance is defective, advise you on how
to obtain a replacement or refund.
In Australia you are entitled to a
replacement or refund for a major failure and
for compensation for any other reasonably
foreseeable loss or damage. You are also
entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to
a major failure.
Should your appliance require repair or
service after the guarantee period, contact
your nearest Sunbeam service centre.
Your Sunbeam 2 Year Replacement
Guarantee naturally does not cover misuse
or negligent handling and normal wear and
tear.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:
Australia
Similarly your 2 Year Replacement Guarantee
does not cover freight or any other costs
incurred in making a claim. Please retain
your receipt as proof of purchase.
1300 881 861
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to the
appliance.
New Zealand
0800 786 232
26 Vestey Drive, Mt Wellington
Auckland, New Zealand
Our goods come with guarantees that cannot
be excluded under the Australian Consumer
Law and under the New Zealand Consumer
Guarantees Act.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Or call 1300 881 861
In New Zealand
Or call 0800 786 232
is a registered trademark.
‘Pro Steam’ is a registered trademark of Sunbeam Corporation.
‘Teflon’ is a registered trademark of DuPont.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright. Sunbeam Corporation Limited 2011.
ABN 45 000 006 771
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Unit 3, Building D
26 Vestey Drive
Mt Wellington Auckland
New Zealand
Sunbeam Corporation is a division of GUD Holdings Ltd.
1/11
|