Swann Home Security System SW347 WA2 User Manual

Advanced security made easy™  
Wireless Alarm System  
SW347-WA2  
Operating Instructions  
SW347-WA2  
MWA2080710E  
 
Before You Begin  
FCC Verification:  
NOTE: This equipment has been tested and found to comply with the limits for  
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are de-  
signed to provide reasonable protection against harmful interference in a residen-  
tial installation. This equipment generates, uses and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio or television reception, which can be deter-  
mined by turning the equipment off and on, the user is encouraged to try to cor-  
rect the interference by one or more of the following measures:  
· Reorient or relocate the receiving antenna  
· Increase the separation between the equipment and the receiver  
· Connect the equipment into an outlet on a circuit different from that to which  
the receiver is connected  
· Consult the dealer or an experienced radio/TV technician for help  
IMPORTANT NOTE: Prohibition against eavesdropping  
Except for the operations of law enforcement officers conducted under lawful  
authority, no person shall use, either directly or indirectly, a device operated pursu-  
ant to the provisions of this Part for the purpose of overhearing or recording the  
private conversations of others unless such use is authorized by all of the parties  
engaging in the conversation.  
WARNING: Modifications not approved by the party responsible for compliance  
could void users authority to operate the equipment.  
IMPORTANT SAFETY INSTRUCTIONS:  
· Make sure product is fixed correctly and stable if fastened in place  
· Do not operate if wires and terminals are exposed  
IMPORTANT: Regarding Your Passcode  
The Default Passcode is 1235.  
In the event that the default settings for the alarm system are restored,  
or you accidentally lock the system before setting a passcode of your  
own, then this is the code you’ll need to unlock the system.  
We strongly recommend choosing a new password as soon as possible.  
2
 
IMPORTANT - Read Before Installing  
For your safety and the safety of others, and to ensure that you get the most out of  
the Home Wireless Alarm System, please read and adhere to these guidelines.  
Do not expose any part of the Wireless Alarm System to any sudden shocks  
(such as being dropped or struck).  
Do not install the PIR Motion Sensors near any device which emits heat or cold,  
such as air conditioners, refrigerators, ovens, heaters, microwaves or other  
electronic equipment which generates heat as a by-product of operation.  
Do not install any component of the Home Wireless Alarm System in direct  
sunlight.  
Use only alkaline batteries.  
All components are for indoor use only. Do not install outdoors.  
Replace the batteries in the units every six months. There are batteries in  
the Remote Controls, Window/Door Sensors and in the PIR Motion Sensors.  
Test the alarm periodically (every 1 - 2 months and each time you change  
the batteries) to ensure it is working properly.  
For the best results, ensure that the antenna on the Keypad Alarm Control  
Unit is extended to its maximum length. The strength of the wireless signal  
is dramatically affected by the placement of the antenna.  
Keep this operating instruction booklet in a safe place.  
This alarm system is designed to be, and acts as, a theft deterrent. This  
system, like any other, cannot offer complete protection for your home  
or business - it is simply an alarm system. Like all practical systems, it has  
limitations and it could be disabled by a skilled intruder. We suggest that you  
avoid relying solely on the Wireless Alarm System to protect your property, but  
use it as part of a comprehensive security solution. You can increase your level  
of protection through the use of high-quality locks, stronger doors, guards  
for your windows and a CCTV system combined with audio-visual recording  
devices.  
4
 
About the Wireless Alarm System  
The Wireless Alarm System is a convenient, cost-effective and easy to install  
security system for your home or small business. Combining multiple types of  
sensors, multiple alarm zones, two modes of operation and the convenience of  
wireless technology, Swanns Home Wireless Alarm System offers flexible solutions  
for almost any kind of environment.  
Throughout this instructional manual, we’ll be referring to the building in which  
the alarm is installed as the “house” or “home”. This is not to say that the Wireless  
Alarm System cannot be installed in a business, office, warehouse or wherever you  
desire – however, we do anticipate that home security is the most practicable use  
for the Wireless Alarm System, and this manual is written from that viewpoint.  
The methodology for installing the alarm system in another type of environment  
is practically identical.  
Placement of the Keypad Alarm Control Unit and Sensors:  
Before attempting to install the Home Wireless Alarm System, its worth taking the  
time to really think about and plan the best locations in your home to place your  
sensors and Keypad Alarm Control Unit.  
When it comes to placing the sensors, there are two conflicting needs to consider.  
On the one hand, its important for the sensors to cover the areas most vulnerable  
to intrusion but, on the other hand, it shouldn’t be too easy for an intruder to  
access the sensors and avoid or physically damage them.  
The Keypad Alarm Control Unit needs to be located somewhere close enough to  
an entrance/exit that you can get to it relatively quickly – this is important when  
arming the system before leaving the house, or disarming it when returning home  
if you don’t have the remote control handy. You certainly don’t want false alarms;  
but if they do occur, you want either the remote or Keypad Alarm Control Unit  
easily accessible to stop it before it wakes the neighbourhood!  
Installing the Keypad Alarm Control Unit:  
Remember that, unlike the sensors, the Keypad Alarm Control Unit needs to  
be connected to power using the supplied 9V power adaptor.  
5
 
The Keypad Alarm Control Unit  
The Keypad Alarm Control Unit is the heart of the Wireless Alarm System. It is  
responsible for monitoring the various sensors throughout your home, and for  
triggering the alarm signal when one of them reports a disturbance. As such,  
it is the single most important part of the Wireless Alarm System, and (with the  
possible exception of the remote controls) the part of the system that you will use  
most often.  
Heres a quick rundown of the various buttons on the Keypad Alarm Control Unit and  
what they do. We’ll cover the more advanced operations later in this manual.  
Siren Connection  
Antenna  
Zone Set &  
Setup Buttons  
Zone LEDs  
Numerical Keypad  
Mode Indicator LEDs  
Arming Buttons  
Out Button: Used when arming the Wireless Alarm System for “Out Mode”.  
Home Button: Used when arming the Wireless Alarm System for “Home Mode”.  
Disarm Button: Used to disarm the Wireless Alarm System.  
Alarm Button: Used to trigger the alarm manually. Essentially, this is a panic  
button, and can also be used to test the functionality of the siren. Additionally, this  
button will bypass the arming delay if pressed after arming the system.  
Home LED: When constantly lit, this indicates that the Wireless Alarm System is  
armed in “Home Mode”. When flashing, it means that the Wireless Alarm System  
is currently counting down the 30 second delay before arming “Home Mode”.  
Out LED: When constantly lit, this indicates that the Wireless Alarm System is  
armed in “Out Mode”. When flashing, it means that the Wireless Alarm System is  
currently counting down the 30 second delay before arming “Out Mode”.  
Alarm LED: Indicates that the alarm has been tripped.  
6
 
The Window/Door Sensor  
The included Window/Door Sensors are  
Trigger  
extremely reliable, and will be triggered  
every time the door on which they are  
mounted is opened.  
Siren  
When the two parts of the sensor are  
extremely close to one another (ideally  
touching) the sensor is deactivated. As  
soon as the two parts are moved apart by  
about 1/2 of an inch (about 10-15mm),  
this will cause the transmitter to send the  
alarm signal.  
Transmitter  
We suggest using the Window/Door  
Sensors as your primary alarm triggers.  
They are reliable and, if installed correctly,  
can safeguard doors and windows from  
being opened without your knowledge.  
Battery  
Compartment  
However, these types of sensors can be circumvented if a window or fragile door  
were broken rather than opened. Thus, we suggest using the infrared sensors as a  
backup to the Window/Door Sensors.  
IMPORTANT: The Window/Door Sensor only works correctly when the trigger is  
aligned to the right-hand side of the transmitter as pictured above. The trigger  
should be placed on the side opposite to the RF+ALARM/OFF/RF switch.  
Environments with extreme fluctuating magnetic fields (such as around devices like  
microwaves) can interfere with the proper functioning of the Window/Door Sensor.  
We suggest avoiding placing the Window/Door Sensor near these devices.  
Modes:  
OFF: The Window/Door Sensor is inactive.  
RF: When triggered, the Window/Door Sensor will transmit a signal to the control  
unit. The built-in siren will not sound.  
RF+ALARM: When triggered, the Window/Door Sensor will transmit a signal to  
the control unit in addition to sounding the internal siren. The additional siren in  
the sensor is a great backup to the main alarm units siren, and will sound in the  
place the alarm is triggered.  
7
 
The PIR motion sensor  
PIR Motion Sensor  
The Passive InfraRed (PIR) Motion Sensor will, under  
typical conditions, detect a human being moving around  
within approximately thirty feet (about 10m) from the  
sensor. This is an average value, as the actual detection  
range is between 16ft/5m and 50ft/15m.  
As the performance of the sensor is determined  
primarily by environmental conditions, no guarantees  
can be offered regarding the detection range. However,  
the range is typically sufficient for the majority of  
interior spaces (excluding the obviously absurd, such  
as basketball courts or aircraft hangars). Some garages  
may be large enough that one sensor cannot cover  
the whole area – we suggest testing this in the actual  
environment if theres any doubt.  
The sensor has a 110º field of view horizontally, and a slightly narrower view  
(approximately 70º) vertically. This means that most of what you could see if you  
closed one eye and put your head where you’d mount the sensor is pretty close to  
the area the sensor will cover. The main blind spots, of course, are above, below  
or behind the sensor itself.  
Typically, the ideal placement in an environment is in the upper corner of a room,  
facing slightly towards the ground (perhaps 20-25º, depending on the height of  
the sensor). Try to cover typical paths through the room, focussing particularly on  
likely entry and exit points. If the room has several entry points, try to cover as  
many of these as practicable.  
A visible PIR motion sensor can be a great deterrent to intruders – but on the other  
hand, skilled intruders can avoid obviously visible sensors. Try to mix it up a bit.  
How it works:  
The PIR motion sensor is a passive infrared motion sensor, meaning it detects  
infrared radiation rather than projecting it (unlike a security camera with infrared  
night vision, which is active infrared). All objects emit this “black-body radiation”  
(we commonly call it “heat”) and the infrared sensor looks for any of this radiation  
which moves.  
The PIR motion sensor is not infallible – in particular, it cannot detect objects/people  
which are the same temperature as their background. So a human being moving  
about on an extremely hot day might go unnoticed. Also, a security camera with  
active infrared night vision in the same vicinity as the infrared sensor may give false  
alarms (particularly if it is a moving PTZ system).  
8
 
Placing the PIR motion sensors  
The PIR motion sensors have an effective range of between 16ft/5m and 50ft/15m  
depending on the specific conditions of the environment. Typically, the sensor will  
have a longer range in colder conditions, or in evenly heated environments. The  
opposite is also true - environments with uneven temperatures (such as part of the  
area in sunlight and other areas in shade) or consistently high temperatures will  
lower the effective range of the sensor.  
Under typical circumstances, the effective range of the PIR motion sensor is  
approximately 50ft/15m. Multiple sensors can be used in conjunction with one  
another to cover larger spaces.  
50ft/15m  
This diagram  
shows a typical  
32ft/10m  
coverage area  
for an evenly  
heated space  
with an ambient  
temperature of  
16ft/5m  
approximately  
110°  
68°F/20ºC with  
low relative  
humidity.  
Higher humidity  
or higher/lower  
temperatures will  
alter the effective  
70°  
range of the  
sensor.  
Feet / Meters  
16ft/5m  
32ft/10m  
50ft/15m  
Important:  
Any obstructions in the environment will reduce the sensors effectiveness. It  
can’t see through walls! Even a thin sheet of glass will significantly impair the  
range of the sensor, as glass blocks more infrared radiation than visible light.  
Small animals (such as a cat or similar) can, under some circumstances, trigger  
the PIR motion sensors. Therefore, we suggest that the PIR motion sensors are  
not suited to areas where pets are routinely kept.  
9
 
The Remote Control  
Your wireless alarm system comes with a keychain-sized remote control. In many  
ways, the remote control is the most powerful and important device in your security  
system – essentially, it is the electronic key. Treat it like you would any other key -  
keeping it on your keychain typically helps.  
Using the remote control, you can arm and disarm the system (in either Home  
Mode or Out Mode) from anywhere in range of the wireless signal.  
Arm Out Mode  
Arm Home Mode  
Keyguard  
Disarm  
The remote  
control with the  
keyguard closed.  
Alarm / Panic  
Disarm: Used to disarm the Wireless Alarm System, whichever mode it is in.  
Arm Out Mode: Selects and arms Out Mode.  
Arm Home Mode: Selects and arms Home Mode.  
Alarm Button: Trigger the alarm immediately - this can be used as a panic button or  
to test the siren is in working order. Alternately, when arming the system, pressing this  
button will bypass the thirty second arming delay (as indicated by the applicable Mode  
LED on the Keypad Alarm Control Unit flashing) and arm the system immediately.  
Keyguard: A small sliding tab which can be placed to prevent accidental arming  
or disarming of your alarm system when being carried in a pocket or bag.  
Pairing the Remote Controls  
The remote controls which came with your Home Wireless Alarm System should  
already be paired with your Keypad Alarm Control Unit. If they don’t seem to work  
right away, or you accidentally un-pair them (this can happen whilst assigning  
sensors to zones) then follow this quick procedure to re-pair the remote controls:  
Press and hold the ZONE SET button for approximately 6 seconds, until the  
unit beeps twice.  
Press any key on the remote control you want to pair. The Keypad Alarm  
Control Unit will beep to confirm that it has detected the signal from the  
remote.  
Press the Zone Button to exit pairing mode. The Control Unit will beep twice  
to confirm the remote control has been paired.  
10  
 
Your Passcode & Alarm Duration  
To protect the security and integrity of your alarm system, you’ll need to define a  
unique passcode. Your passcode must be four (4) digits long – something you’ll  
remember but not something so obvious that an intruder would be able to guess.  
Try to avoid the obvious numbers, such as birthdays and anniversaries. Though  
they are easy to remember, they are also easy for someone else to discover.  
The best passcodes are arbitrary, random numbers.  
We strongly advise that the passcode not be recorded in writing anywhere. Treat  
your passcode with the same diligence as you would your personal identification  
number (PIN) on your bank card - perhaps even more so.  
To program your unique passcode:  
Press and hold the SETUP button. The unit will beep. Keep holding down the  
SETUP button for approximately six seconds, until the unit beeps twice.  
Then, enter your four digit passcode. Be careful not to make any mistakes!  
Press “*” then “#” then “7”  
The Keypad Alarm Control Unit will confirm with one long beep.  
Press SETUP. The unit will beep twice, confirming that it has saved your new  
passcode.  
Important: Your passcode should be kept as secret as possible, only told to those  
who absolutely need to know. If you feel that your passcode has been revealed to  
or discovered by a third party, you should change it immediately.  
Changing the Alarm Duration:  
The “Alarm Duration” is the amount of time that the siren will sound after the  
alarm is triggered. You can set the siren to sound for 1 to 20 minutes* (01 ~ 20)  
or set the siren to be inactive.  
Press and hold the SETUP button. The unit will beep. Keep holding down the  
SETUP button for approximately six seconds, until the unit beeps twice.  
Input “007”  
Input “XX”, where XX is the number of minutes you want the siren to sound  
for. For values below 10, enter “0” first (eg. for five minutes, enter “05”). If  
you want to turn the siren off altogether, enter “00”.  
Input “**” then press SETUP to finish. The unit will beep twice, confirming  
that it has saved the new alarm duration.  
* Many localities have very specific regulations regarding the allowable volume  
and duration of an audible alarm. Before configuring your system, we suggest that  
you check with your local authorities regarding the laws and regulations that apply  
to you, and adhere to these regulations.  
11  
 
Alarm Zones and Modes  
Modes:  
The Wireless Alarm System has two main modes of operation, the Home Mode  
and Out Mode. These zones do not refer to where the sensors are placed, but  
where you are at any given time.  
For example, when you are in your home, you should set the alarm system to  
“Home”. Home Mode should include your Window/Door Sensor(s) and any other  
sensors you want to be active while there are people in the house. For this reason,  
we suggest not assigning any of the PIR motion sensors inside your home to a zone  
which is armed in Home Mode - it will give you many ‘false’ alarms.  
Arming “Out Mode” will arm all zones on the alarm system. Thus, this should only  
be armed when there is to be no-one in the house.  
Zones:  
The Wireless Alarm System has eight discreet zones, named 1 through 8. Any (or  
all, or none) of these zones can be assigned to the Home Mode. All zones are  
always associated with Out Mode.  
Thus, arming Home Mode will arm only the zones you have assigned to Home  
Mode. We suggest that the Window/Door Sensor works well assigned to Home  
Mode.  
Activating Out Mode will arm all the sensors attached to your alarm system, those  
located both inside and outside the home.  
To briefly summarize:  
Will armm all of tthe zonnes whiicch you’vve assiigned tto Home  
Home Mode  
Out Mode  
Mode. This is intended for use when tthheerree aarree ppeeooppllee  
in the home whho want the pperimeter to be secure (for  
example, while they are sleeping).  
Will armm sensorrs in allll eight zzones. TThis modde iiss iinntteennddeedd  
to be activated whilst there is nobody in the house.  
You can change the Zone and Mode that a sensor is assigned to  
when you pair it with the Keypad Alarm Control Unit.  
See the sensor pairing instructions on page 13.  
12  
 
Pairing Sensors  
Each sensor in your system needs to be paired with a mode and zone on the  
Keypad Alarm Control Unit. You can have multiple sensors in a single zone and/or  
zones with no sensors attached. If you choose, you can have all your sensors in the  
Home or Out modes, or a combination of both. We recommend a combination of  
both, as this adds functionality and value to your alarm system.  
Press the ZONE SET button and hold for approximately 6 seconds, until the  
Keypad Alarm Control Unit beeps twice.  
Press HOME if you’d like to assign a sensor to the Home Zone, or OUT if you  
want to assign the sensor be active to Out Mode.  
Press number on the keypad for the zone that you would like to assign the  
sensor to.  
Trigger the sensor you wish to assign to that zone.  
To confirm your selection, press the Zone Set button. The Keypad Alarm  
Control Unit will beep twice. Otherwise, the system will ‘time out’ after 40  
seconds and discard your changes.  
Repeat this procedure until all your sensors have been assigned to their  
respective zones.  
How many sensors can I assign to a single zone?  
The short answer is: as many as you want.  
The longer answer is: the Wireless Alarm System can support dozens wireless  
sensors at a time. The only limitation is due to the available bandwidth (number  
of radio frequencies) that the Wireless Alarm System can individually identify. As  
the Wireless Alarm System comes with only four sensors (two PIR motion sensors  
and two Window/Door Sensors) the bandwidth limitation won’t present an issue  
unless you dramatically increase the scope of your alarm system.  
Any number of sensors can be paired to a single zone, up to the maximum number  
supported by the system. However, we recommend spreading them out over all  
eight zones, as this will allow you to more easily determine at a glance what  
sensors have been tripped and which have not.  
Swann offers no guarantee that any third party sensors will be compatible  
with the Wireless Alarm System. In fact, we suggest that they probably will not  
be. There are many protocols and formats for alarm signals, most of which will  
not work with this system.  
13  
 
Arming and Disarming the System  
There are two ways to arm the system, using either the Keypad Alarm Control Unit  
or the remote. Arming the system via the remote control is quick, requiring only  
a couple of buttons be pushed. Arming the system via the Keypad Alarm Control  
Unit is likewise quick and easy, but for security purposes, you’ll need your passcode  
to gain access to the system.  
To arm the Wireless Alarm system in Home Mode:  
Press  
on the remote control. Alternately, you can unlock the keypad control  
unit by typing your passcode and then press the HOME button.  
The system will begin the 30 second arming delay. After this period elapses,  
the sensors assigned to the Home Zone will be armed.  
You can press  
during the arming delay to arm the system immediately.  
To arm the Wireless Alarm system in Out Mode:  
(or the ALARM button if using the keypad control unit)  
Press  
on the remote control. Alternately, you can unlock the keypad control  
unit by typing your passcode and then press the OUT button.  
The system will begin the 30 second arming delay. After this period elapses,  
the sensors assigned to the Out Zone will be armed.  
You can press  
during the arming delay to arm the system immediately.  
To disarm the Wireless Alarm system:  
(or the ALARM button if using the keypad control unit)  
Press the  
button on the remote control.  
Alternately, you can unlock the keypad control unit using your passcode, and  
then press the DISARM button. If you choose to disarm the system this way, be  
aware that there is no entry delay: the alarm will sound as soon as a sensor  
is triggered. If you want to use the system in this way, ensure that you can  
reach the keypad control unit before triggering the alarm.  
Panic Alarm  
To instantly sound the alarm in the event of an emergency, press the  
button.  
Alternately, you can unlock the keypad control unit using your passcode and  
then press the ALARM button.  
This panic alarm can be stopped by disarming the system, as described above.  
14  
 
Batteries  
Both the Window/Door Sensors and PIR Motion Sensors have included batteries, as  
does the remote control. These are necessary for the alarms to be able to transmit  
an active wireless signal. The functionality of the sensors is reliant on the batteries  
providing power in much the same way as a smoke detector.  
We recommend changing the batteries in all sensors every six months.  
The expected life of the batteries is actually considerably longer than this (they’ll  
probably last for a year or more). However the consequences of the batteries  
running low can be so dramatic that we strongly recommend changing to fresh  
batteries long before there is a chance that they’ll run down - much like the  
recommendations for smoke detectors.  
Window/Door Sensor: 3 x LR44 Button Cells  
The battery compartment on the Window/Door Sensor is located on the front of  
the alarm unit. To open it:  
Press in at the top of the battery compartment cover and slide down.  
Remove any old batteries.  
Insert three fresh alkaline LR44 button cell batteries. The correct orientation is  
to have the “+” side of the battery facing up.  
PIR Motion Sensor: 3 x AAA  
The battery compartment on the PIR is located on the rear of the sensor, just  
underneath mounting bracket slot. To change the batteries:  
Push the top of the battery compartment cover in, and push down to remove.  
Replace the three AAA batteries with fresh alkaline AAA batteries. Be sure to  
insert the batteries in the orientation indicated on the rear side of the battery  
compartment.  
Remote Control: 1 x 27A  
To change the battery in the remote:  
Unscrew the three screws on the back of the remote control.  
Remove the front plate and the buttons. Be careful not to lose the buttons or screws.  
Replace the 12V 27A battery located in the middle of the circuit board.  
The keypad control unit does not require batteries.  
It is powered by the included 9V adaptor.  
If you’re concerned about potential power failures, you may consider using a  
small UPS (Un-interruptible Power Supply) as a backup to your mains power.  
15  
 
Troubleshooting  
Problem: I keep getting false alarms!  
Solution: There are a few possible reasons why this might be occurring.  
1. Check that there are no strong magnetic fields around your Window/Door  
Sensor(s). Things like televisions, computers, microwaves and (of course)  
magnets of any kind will interfere with the proper operation of the Window/  
Door Sensor and could lead to false alarms.  
2. Check that there are no shifting heat sources in view of the PIR Motion  
Sensor(s). This includes the obvious things, such as moving animals or people,  
but also things such as a moving shadow on a hot day (such as the shadow of  
a tree blowing in the wind). Sometimes reflected infrared heat from the sun in  
enough to trigger the sensor.  
3. If you’ve had the system installed for some time, then the batteries built into  
the sensors might be running low, causing erratic behavior.  
4. If you’re using the Wireless Alarm System in an environment with a high level  
of radio ‘noise’ (that is, somewhere that there are many other wireless devices  
in use) then these interfering signals might be interpreted as the system as  
alarm signals. This should, however, be a very rare occurrence.  
Problem: My PIR Motion Sensor isn’t detecting movement.  
Solution: Sometimes, heat sources too close (within a few feet/about 2m) away  
from the sensor will not set it off. The sensor is designed to be most sensitive to  
things at mid-range (between about 6ft/2m and 26ft/8m) and sometimes can’t  
focus on things closer than this. Its a little like holding something too close to your  
own eyes - you won’t be able to focus on it!  
Problem: I’m concerned that my passcode is no longer secret.  
Solution: Change it immediately, and inform anyone who needs to know. Your  
Wireless Alarm System is designed to help protect you, your family and your  
possessions - it can’t do its job if potential risks can access and disable the system  
easily. If in doubt, change the passcode - after all, its better to have an embarrassing  
false alarm by forgetting the passcode than having the system fail right when you  
need it the most.  
16  
 
Problem: What if the power goes out?  
Solution: In the event of a general power failure, the Wireless Alarm System will  
not have the power it requires to operate. One solution is to acquire and use an  
Un-interruptible Power Supply (UPS). If you are using the Wireless Alarm System  
in combination with an overall and comprehensive security package (which we  
recommend) attaching all the powered components of your system to a UPS is  
generally advisable.  
Problem: Can I connect additional sensors to the alarm system?  
Solution: Yes, provided that they match the specifications of the included sensors.  
Specifically, they must communicate using analog wireless transmitters, operating  
at a frequency of 433MHz. We only guarantee that sensors sold by Swann  
specifically for this alarm system will operate correctly - no guarantee is made or  
implied regarding third party hardware.  
Problem: How do I change the amount of time the siren sounds for?  
Solution: You can set the siren to sound for between 1 minute and 20 minutes  
(or turn it off altogether). Instructions on how to do this are located on page 11.  
Remember to check the rules and regulations relating to audible alarms in your  
locality.  
Problem: The alarm doesn’t go off when a sensor is triggered.  
Solutions: Ensure that the sensor is properly paired with the Keypad Alarm  
Control Unit (see the instructions regarding how to do so on page 13). Check the  
batteries in the sensor in question - if the batteries are too low, the sensor will not  
have enough power to send the signal to the Keypad Alarm Control Unit. Finally,  
remember that, like radio, wireless signals are sent and received more effectively  
when all antennas are extended fully.  
Problem: My remote controls don’t seem to be working.  
Solution: They probably need to be re-paired with the Wireless Alarm Unit. See  
page 10 for instructions on how to pair/re-pair the remote controls.  
17  
 
Technical Specifications  
Keypad Control Unit  
Power Requirements  
Wireless Frequency  
Sensitivity  
9V DC (supplied adapter)  
433 MHz  
>-110dB  
Siren Volume  
> 110dB  
Alarm Duration  
Operating Temperature  
0 ~ 20 minutes  
-10C° ~ +40C°  
Remote Control  
Battery Requirements  
1 x 27A (12V DC)  
0mA  
<10mA  
433 MHz  
Up to 262ft/80m line of sight  
65ft/20m  
Power Consumption (Standby)  
Power Consumption (Operating)  
Transmission Frequency  
Transmission Range  
Typical Transmission Range  
Operating Temperature  
-10C° ~ +40C°  
Passive Infrared Sensor  
Detection Range  
Typical Detection Range  
Battery Requirements  
Power Consumption (Standby)  
Power Consumption (Operating)  
Transmission Frequency  
Transmission Range  
Typical Transmission Range  
Operating Temperature  
> 5m (open area)  
16ft / 5m ~ 50ft / 15m  
3 x AAA (4.5V DC)  
< 0.1mA  
< 8mA  
433 MHz  
Up to 262ft/80m line of sight  
65ft/20m  
-10C° ~ +40C°  
Magnetic Window/Door Sensor  
Battery Requirements  
4 x LR44 Button Cells (6V DC)  
< 10µA  
< 15mA  
433 MHz  
Up to 262ft/80m line of sight  
65ft/20m  
Power Consumption (Standby)  
Power Consumption (Operating)  
Transmission Frequency  
Transmission Range  
Typical Transmission Range  
Operating Temperature  
-10C° ~ +40C°  
18  
 
Warranty Information  
Swann Communications LTD.  
Stag Gates House  
63/64 The Avenue  
SO171XS  
Swann Communications USA Inc.  
Swann Communications  
Unit 13, 331 Ingles Street,  
Port Melbourne Vic 3207  
12636 Clark Street  
Santa Fe Springs CA 90670  
USA  
United Kingdom  
Swann Communications warrants this product against defects in workmanship  
and material for a period of one (1) year from it’s original purchase date. You  
must present your receipt as proof of date of purchase for warranty validation.  
Any unit which proves defective during the stated period will be repaired  
without charge for parts or labour or replaced at the sole discretion of Swann.  
The end user is responsible for all freight charges incurred to send the product  
to Swann’s repair centres. The end user is responsible for all shipping costs  
incurred when shipping from and to any country other than the country of  
origin.  
The warranty does not cover any incidental, accidental or consequential  
damages arising from the use of or the inability to use this product. Any costs  
associated with the fitting or removal of this product by a tradesman or other  
person or any other costs associated with its use are the responsibility of the  
end user. This warranty applies to the original purchaser of the product only  
and is not transferable to any third party. Unauthorized end user or third party  
modifications to any component or evidence of misuse or abuse of the device  
will render all warranties void.  
By law some countries do not allow limitations on certain exclusions in this  
warranty. Where applicable by local laws, regulations and legal rights will take  
precedence.  
19  
 
Swann Technical Support  
All Countries E-mail: [email protected]  
Telephone Helpdesk  
USA toll free  
1-800-627-2799  
AUSTRALIA toll free  
1300 138 324  
(Su, 2pm-10pm US PT)  
(M-Th, 6am-10pm US PT)  
(F 6am-2pm US PT)  
USA Exchange & Repairs  
1-800-627-2799 (Option 1)  
(M-F, 9am-5pm US PT)  
(M 9am-5pm AUS ET)  
(Tu-F 1am-5pm AUS ET)  
(Sa 1am-9am AUS ET)  
NEW ZEALAND toll free  
0800 479 266  
UK  
0203 027 0979  
current time in Melbourne, Australia compared to your local time.  
© Swann Communications 2010  
 

Sharp Blu ray Player 10P01 CH NG User Manual
Sharp Fax Machine UX A760 User Manual
Sharp Projector XR 50S User Manual
Sony Camera Accessories MSAC M2 User Manual
Sony Ericsson Cell Phone K205 User Manual
Sony Microcassette Recorder ICD BX022 User Manual
Sony Stereo System 3 300 703 112 User Manual
Sony Telephone SX M100 User Manual
Source Technologies Printer STM58B User Manual
Swann DVR SW242 2LP User Manual