OWNER’S
MANUAL
9-INCH COLOR TV/DVD
6509DD
This Owner’s Manual is made of
recycled paper.
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
As an ENERGY STAR®
Partner, our company has
determined that this product meets
the ENERGY STAR® guidelines for
energy efficiency. ENERGY STAR® is
a U.S. registered mark.
If you need additional assistance for set-up or operating after
reading owner’s manual, please call TOLL FREE : 1-800-968-3429.
Download from Www.SoPmlaenauaslse.croema. dAllbMeafnouarles SuesaircnhgAnthd iDsowenqlouaidp. ment
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD I N
WI RE
GROUND
CL AMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRI C
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC
-
NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying par-
ticular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
19.Damage Requiring Service-Unplug this TV/DVD from
the wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/DVD.
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/DVD, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
c. If the TV/DVD has been exposed to rain or water.
d. If the TV/DVD does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the TV/DVD to its normal operation.
e. If the TV/DVD has been dropped or damaged in any way.
f. When the TV/DVD exhibits a distinct change in perfor-
mance-this indicates a need for service.
14.Lightning-For added protection for this TV/DVD receiver
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the TV/DVD due to lightning and
power-line surges.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other haz-
ards.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
21.Safety Check-Upon completion of any service or repairs to
this TV/DVD, ask the service technician to perform routine
safety checks to determine that the TV/DVD is in proper
operating condition.
22.Heat-This TV/DVD product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/DVD through openings as they may touch dan-
gerous voltage points or short out parts that could result in
a fire or electric shock. Never spill liquid of any kind on
the TV/DVD.
18.Servicing-Do not attempt to service this TV/DVD yourself
as opening or removing covers may expose you to danger-
ous voltage or other hazards. Refer all servicing to qualified
service personnel.
EN
–
–
3
0C28
PRECAUTIONS
IMPORTANT COPYRIGHT INFORMATION
LASER SAFETY
Unauthorized copying, broadcasting, public perfor-
mance and lending of discs are prohibited.
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to ser-
vice this device, due to possible eye injury.
FCC WARNING- This equipment may gener-
ate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction man-
ual. The user could lose the authority to oper-
ate this equipment if an unauthorized change
or modification is made.
CAUTION: USE OF CONTROLS OR ADJUST-
MENTS OR PERFORMANCE OF PROCE-
DURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
RADIO-TV INTERFERENCE
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est con-
forme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable
and can be reused. Please dispose of any materials
in accordance with your local recycling regula-
tions.
Batteries should never be thrown away or inciner-
ated but disposed of in accordance with your local
regulations concerning chemical wastes.
3) Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
The serial number of this product may be found on the back of the unit. No other TV/DVD has the same serial
number as yours. You should record the number and other vital information here and retain this book as a per-
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
EN
–
–
4
0C28
LOCATION
SUPPLIED ACCESSORY
For safe operation and satisfactory performance of
your TV/DVD, keep the following in mind when
selecting a place for its installation:
Remote Control Unit
(PART NO.: NE207UD)
•
Shield it from direct sunlight and keep it away from
sources of intense heat.
Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at
the top and bottom of the unit. Do not place the unit
on a carpet because this will block the ventilation
holes.
Install unit in a horizontal position.
Avoid locations subject to strong vibration.
•
2 AA Batteries
•
•
•
•
Indoor Antenna
(PART NO.:
0EMN00723 or 0EMN01183)
Matching Adapter
(300ohm-75ohm)
•
•
(PART NO.: 1813641 or
1780258 or UCPGANTPK004)
•
•
Car Battery Cord
(PART NO.: WPC0202GA001
or WPC0202HHH001)
Do not place the TV/DVD near strong magnetic fields.
Avoid moving TV/DVD to locations where temper-
ature differences are extreme.
•
•
AVOID THE HAZARDS OF
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some head-
ings and notes in this manual, with the following
meanings
ELECTRICAL SHOCK AND FIRE
Do not handle the power cord with wet hands.
Do not pull on the power cord when disconnecting
•
•
it from an AC wall outlet. Grasp it by the plug.
If, by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Do not put your fingers or objects into the
TV/DVD disc loading tray.
Do not place anything directly on top of the unit.
TV
•
: Description refers to TV operation (in the TV mode).
DVD-V
: Description refers to playback of DVD video discs
(in the DVD mode).
•
CD
•
: Description refers to playback of audio CDs
(in the DVD mode).
WARNING
MP3
: Description refers to playback of MP3 discs
(in the DVD mode).
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. If a DVD is played in a TV/DVD
which has moisture, it may damage the DVD and
TV/DVD. Therefore when the condensation occurs
inside the unit, turn POWER on and allow at least 2
hours for the unit to dry out.
QUICK
: Description refers to the items to be set by the
QUICK mode (in the DVD mode).
EN
–
–
5
0C28
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
C SEARCH FUNCTION . . . . . . . . . . . . . . . . . .21
TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . .21
TITLE / CHAPTER SEARCH . . . . . . . . . . . . .21
TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . .21
MARKER SETUP SCREEN . . . . . . . . . . . . . .21
C
OPERATING CONTROLS AND FUNCTIONS . . .8
INSTALLING THE BATTERIES . . . . . . . . . . .9
C SPECIAL PLAYBACK FUNCTION . . . . . . . .22
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .22
RANDOM PLAYBACK . . . . . . . . . . . . . . . . .22
C PREPARATION FOR USE . . . . . . . . . . . . . . .10
ANTENNA/CABLE CONNECTIONS . . . . . . .10
INDOOR ANTENNA . . . . . . . . . . . . . . . . . . .10
CONNECTING TO EXTERNAL INPUT JACKS .11
C PLAYING A MP3 DISC . . . . . . . . . . . . . . . . . .23
MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . .23
TRACK SELECTION . . . . . . . . . . . . . . . . . . .23
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .23
RANDOM PLAYBACK . . . . . . . . . . . . . . . . .23
CONNECTING TO A STEREO SYSTEM . . . .12
CONNECTING TO AN AMPLIFIER
EQUIPPED WITH DIGITAL INPUT JACKS,
MD DECK OR DAT DECK (for DVD only) . .12
CONNECTING TO A DOLBY DIGITAL
DECODER (for DVD) . . . . . . . . . . . . . . . . . . .13
C CHANGING THE SETTINGS . . . . . . . . . . . .24
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . .24
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . .24
STEREO SOUND MODE . . . . . . . . . . . . . . . .24
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . .24
BLACK LEVEL SETTING . . . . . . . . . . . . . . .24
VIRTUAL SURROUND . . . . . . . . . . . . . . . . .24
TV SECTION
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .14
CHANNEL SET UP FOR THE FIRST TIME . .14
DELETING (OR ADDING) CHANNEL . . . . .14
CHANNEL SET UP AGAIN . . . . . . . . . . . . . .15
SELECTING THE LANGUAGE . . . . . . . . . . .15
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .16
WATCHING A TV PROGRAM . . . . . . . . . . . .16
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .16
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .16
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .17
C THE ON-SCREEN INFORMATION . . . . . . .25
C CHANGING THE DVD SETUP ITEMS . . . .26
LANGUAGE SETTING . . . . . . . . . . . . . . . . .26
DISPLAY SETTING . . . . . . . . . . . . . . . . . . . .27
AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . .27
PARENTAL CONTROL . . . . . . . . . . . . . . . . .28
DVD SECTION
C ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . .18
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . .18
DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . .18
C TROUBLESHOOTING GUIDE . . . . . . . . . . .29
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .31
C PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . .19
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . .19
GENERAL FEATURES . . . . . . . . . . . . . . . . . .19
DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . .19
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . .19
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
STEP BY STEP PLAYBACK . . . . . . . . . . . . .20
FAST FORWARD/REVERSE SEARCH . . . . .20
SLOW FORWARD / SLOW REVERSE . . . . .20
ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . .31
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .32
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover
EN
–
–
6
0C28
FEATURES
TV Mode
DVD Mode
¡Dolby Digital sound
181 channel capability PLL frequency synthesiz-
er tuner with direct station call
(A converter may be necessary to view scrambled
cable channels.)
Infrared remote control
Trilingual on screen menu display selectable in
English, Spanish, or French
•
This player can handle Dolby Digital surround sound
having 5.1 channels when connected to a Dolby Digital
decoder.
¡Still/fast/slow/step playback
Various playback modes are available including still pic-
tures, fast forward/reverse, slow motion and step frames.
•
•
¡Random playback for audio CD and MP3
This player can shuffle the order of tracks to play them in
random order.
¡Sleep Timer
T
he Sleep Timer function enables you to shut off the power
without pressing POWER after a desired time period.
¡Program playback for audio CD and MP3
You can program the order of tracks to play them in any
desired order.
¡Auto Shut Off Function
If there is no air signal input from the antenna terminal and
no operation for 15 minutes, the TV will turn itself off
automatically.
¡DVD menus in a desired language
You can display DVD menus in a desired language, if
available on a DVD.
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no input
from the player for five minutes in the stop mode. When
the screen saver program is activated for 15 minutes, the
power is automatically turned off.
¡Subtitles in a desired language
You can select a desired language for the display subtitles,
if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc contains
sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound mode,
if different languages and modes are available on a disc.
¡Parental lock
You can set the control level to limit playback of discs
which may not be suitable for children.
¡Automatic detection of discs
This player automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
¡On-screen display
Information about the current operation can be displayed
on a TV screen, allowing you to confirm the currently
active functions (such as program playback), on the TV
screen using the remote control.
¡Search
Chapter search / Title search / Track search / Time search
¡Repeat
Chapter / Title / Track / Group / All / A-B
¡Zoom
Magnified screen can be displayed.
¡Marker
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which the
play was stopped.
¡Virtual Surround
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
EN
–
–
7
0C28
OPERATING CONTROLS AND FUNCTIONS
[Fig. 1]
[Fig. 3]
TV/DVD FRONT PANEL
TV/DVD REAR VIEW
DC 13.2V
ANT.
L
AUDIO OUT
R
VIDEO
L
AUDIO
R
POWER
VOLUME
CHANNEL
STOP
SKIP
PLAY
SKIP
PAUSE
OPEN/CLOSE HEADPHONE
SEARCH
COAXIAL
13
1 2
3
4
5
6
7 8 9 101112 14
37
38
39
40
41
[Fig. 2]
REMOTE CONTROL
OPEN/
CLOSE
POWER PICTURE SELECT
4
13
34
6.CHANNEL K/L (CH.K/L) Buttons [page 14]
Press to select memorized channel.
36
1
4
2
5
8
0
3
6
CH.
6
Press to change to TV mode when DVD mode.
16
7.Remote Sensor Window
8.STOP Button [page 19]
Stops operation of the disc.
7
SLEEP
9
+100
VOL.
5
+10
ZOOM
17
SKIP
MUTE
9.SKIP H Button [page 21]
Plays back from the beginning of the current
chapter or track.
9
11
10
35
19
18
PLAY
STOP
REV
FWD
SEARCH (REV) E Button (Front Panel)
[page 20]
8
DISC
MENU
PAUSE SLOW
DISPLAY
During playback or in the pause mode, press and
hold button down for a few seconds to change
reverse playback speed.
12
23
33
32
31
30
ENTER
SETUP
TITLE
RETURN
10. PLAY Button [page 19]
20
21
22
Starts playback of the disc contents.
Press to change to DVD mode when TV mode.
11. SKIP G Button [page 21]
Plays back from the beginning of the next chapter
or track.
CLEAR SEARCH MODE REPEAT
A-B
29
AUDIO SUBTITLE ANGLE
MODE
15
24
25
28
27
26
SEARCH (FWD) D Button (Front Panel)
[page 20]
During playback or in the pause mode, press and
hold button down for a few seconds to change for-
ward playback speed.
1.Disc loading tray
2.VIDEO input Jack [page 11]
Connect to the video output jack of a video
camera or VCR.
12. PAUSE Button [page 20]
Pauses the current disc operation.
13. OPEN/CLOSE Button [page 19]
Press to insert discs into or remove them from the
tray.
3.AUDIO L/R input Jacks [page 11]
Connect to the audio output jacks of a video
camera or VCR.
14. HEADPHONE Jack
To connect headphone (not supplied) for personal
listening.
4.POWER Button [page 14]
Press to turn the power on and off.
5.VOLUME K/L (VOL. m/n) Buttons
Press to control the volume level for the DVD and TV.
EN
–
–
8
0C28
sequence being played back from a different angle.
15. MODE Button [pages 22-24]
Activates program playback or random playback mode
when playing CDs or MP3.
29. REPEAT A-B [page 22]
Repeats playback of a selected section.
16. Number Button
30. RETURN Button [page 24]
TV Mode: [page 14]
Returns to the previous operation.
Press two digits to directly access the desired
channel.
31. ENTER Button [pages 14, 19]
Press to accept a setting.
Remember to press a "0" before a single digit
32. Arrow Buttons
channel.
+100 Button–
TV Mode: [page 14]
Press to select a setting mode from the menu on
the TV screen.
Press to select cable channels which are equal or
greater than number 100.
Press to select or adjust from a particular menu.
DVD Mode: [page 19]
DVD Mode: [page 21]
Press to enter the desired number.
+10 Button–
Use when making settings while watching the
display on a TV screen.
Press to enter the desired numbers which are
equal or greater than number 10.
33. DISC MENU Button [page 19]
Displays the menus in the DVD.
17. SLEEP Button [page 17]
34. SELECT Button [pages 11, 19]
Press to change to TV mode, external input mode
or DVD mode.
Press SLEEP to display the sleep timer and start
the function. The shut off time can be determined
by the number of times you press this button. (0,
30, 60, 90, or 120 minutes)
NOTE: When you select the DVD mode by this
button, press PLAY or OPEN/CLOSE first.
Otherwise, the DVD features are not operated.
18. REV h Button [page 20]
Press to view the DVD picture in fast reverse
motion. Press PAUSE, then press this button to begin
slow motion playback. Press this button repeatedly
to change the reverse speed of slow motion.
35. MUTE Button
Press MUTE to turn off the sound
portion of the TV program. (Volume level display
turns LIGHT RED from LIGHT BLUE.) Press
MUTE again or press VOL. m or n to restore
sound.
FWD g Button [page 20]
Press to fast forward the Disc. Press PAUSE, then
press this button to begin slow motion playback.
Press this button repeatedly to change the forward
speed of slow motion.
36. PICTURE Button [page 16]
Press to enter picture adjustment mode.
19. ZOOM Button [page 20]
37. Power cord
Expands the picture to fill the entire screen.
Connect to a standard AC outlet (120V/60Hz).
NOTE: Remove the power cord from the hook to
avoid breaking a wire before you connect
to a standard AC outlet.
20. SETUP Button [pages 14, 26-28]
Press to enter or exit the TV menu or DVD setup
mode.
21. TITLE Button [page 19]
38. AUDIO L/R output Jack
Connect to the analog audio input of an external
amplifier or decoder.
Displays the title menu.
22. CLEAR Button [pages 21-23]
39. COAXIAL digital audio out Jack (DVD Audio
Only)
Resets a setting.
23. DISPLAY Button
Connect to the digital input of an external
amplifier or decoder.
TV Mode:
Press to display the channel number on the
screen. If you press it again, the channel number
will disappear.
40. ANT. in Jack
Connect to an antenna, cable system, or satellite
system.
DVD Mode: [page 25]
Displays the current status on the TV screen for
checking purposes.
41. DC 13.2V Jack
Connect to the Car Battery Cord.
24. SEARCH MODE Button [page 21]
Press to locate a desired point.
INSTALLING THE BATTERIES
25. AUDIO Button [page 24]
Press to select a desired audio language or sound
mode.
1)Open the battery compartment cover by pressing the
cover on the remote unit in the direction of the arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
26. SUBTITLE Button [page 24]
Press to select a desired subtitle language.
27. REPEAT Button [page 22]
Repeats playback of the current disc, title, chapter
or track.
3)Replace the cover.
28. ANGLE Button [page 24]
NOTES
Press to change the camera angle to see the
¡Do not mix alkaline and manganese batteries.
¡Do not mix old and new batteries.
–
EN
–
9
0C28
PREPARATION FOR USE
ANTENNA/CABLE CONNECTIONS
From Cable System or
Satellite Box or
Cable Box
(Not supplied)
VHF/UHF Antenna
(Not supplied)
OUT
IN
Satellite Dish
VHF Antenna
(Not supplied)
UHF Antenna
(Not supplied)
From
Cable System
DC 13.2V
ANT.
L
AUDIO OUT
R
COAXIAL
VHF/UHF
Combiner
(Not supplied)
or
or
ANT.
or
75-ohm Coaxial
Cable (Not supplied)
Flat twin-lead cable
[Fig. 4]
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building as close to the point of cable entry as practical.
Bent pin
NOTE:
Before plugging the an antenna into the ANT. IN jack of the TV/DVD, check that
the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin
into the ANT. IN jack of the TV/DVD.
Cable
Plug
(Needs to be straightened)(Straight pin)
VHF/UHF COMBINED ANTENNA
A VHF UHF 75 ohm combination antenna can be
connected to ANT terminal.
CABLE WITH CONVERTER/DESCRAM-
BLER BOX OR SATELLITE BOX
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown here.
Channel selection must be made with the converter
box or satellite box. This means that channels cannot
be changed using the TV/ DVD Remote Control.
TO VIEW A SCRAMBLED/UNSCRAMBLED
CHANNEL
1.Set the TV/DVD channel selector to the output
channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
VHF/UHF SEPARATE ANTENNAS
In some areas it will be necessary to use an outdoor
antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Use this connection if your cable system connects
directly to your TV/DVD without a converter box.
Use the TV/ DVD Remote Control to select channels.
2.Select the channel to view at your Cable Converter
Box or Satellite Box.
INDOOR ANTENNA
Indoor Antenna
(Supplied)
The Indoor Antenna (supplied) is detachable. Insert the stem of the antenna into the
hole on the upper-back portion of the TV/DVD. Connect the Indoor Antenna to the
TV/DVD as shown in the diagram. For the best reception, fully extend the Indoor
Antenna and make the necessary adjustments. (Avoid touching the top section when
adjusting.)
Flat twin-lead cable
Matching
Adapter
(Supplied)
NOTE:
The connection of an Indoor antenna may not always give acceptable TV reception.
D
C
1
3
.
2
V
ANT.
L
AUDIO OUT
R
COAXIAL
ANT.
[Fig. 5]
EN
–
–
10
0C28
CONNECTING TO EXTERNAL INPUT JACKS
When you watch a program recorded on an another
[Front of the TV/DVD]
source (VCR or video camera), use the audio/video
input jacks on the front of the TV/DVD.
Connect the audio/video output
VIDEO
L
AUDIO
R
POWER
[Another source]
To the audio
output jacks
jacks of another source to the
AUDIO L/R and VIDEO jacks of
this TV/DVD. Then press SELECT
until "AUX" appears on the screen.
NOTE:
AUX
Audio/Video
cables
(not supplied)
VIDEO
L
AUDIO
R
When you connect a monaural VCR (another
•
etc.
source) to this TV/DVD, connect the Audio output
jack of the monaural VCR (another source) to the
AUDIO L jack of this TV/DVD. The audio will
output in both L and R channel equally.
To the video
output jack
[Fig. 6]
MOBILE CONNECTION
WARNING:The driver should never watch the TV/DVD while operating a motor vehicle.
CAUTION:
When used in moving vehicle, be sure that the unit is secure at all the times to prevent injury.
Consult a professional installer.
If you use the TV/DVD with the vehicle’s engine off, recharge the vehicle’s battery after about
every 4 hours of use to prevent it from running down. After you finish using the TV/DVD be sure
you unplug the car-battery cord from the cigarette-lighter socket.
Do not use this TV/DVD while driving.
•
•
•
•
•
Do not leave this TV/DVD in a car.
This TV/DVD is not designed for use in a car.
NOTES:
1) The supplied indoor antenna is adequate when
your vehicle is stationary. For best reception on
the road, use a high-quality VHF/UHF mobile TV
antenna.
2) Attach the car battery cord to the DC13.2V(12V)
connector on the back of the TV/DVD. Then, con-
nect the other end to your vehicle’s cigarette-
lighter socket.
Be sure your vehicle has a 13.2-volt (12-volt), neg-
ative-ground electrical system.
•
Be sure you use only the supplied car battery cord.
Using another cord could damage the TV/DVD.
•
Be sure the socket is free of ashes and other debris.
Be sure to push the car battery cord’s plug com-
pletely into the cigarette-lighter socket.
•
•
Always unplug the car battery from the cigarette-
lighter socket before you unplug it from the
TV/DVD.
•
To the vehicle's
cigarette-lighter socket
VHF/UHF Combination
Mobile Antenna
(Not supplied)
You must disconnect the car battery cord from the
TV/DVD before you can use the AC power.
Be sure to replace the fuse with only the same type,
6A, 250V.
•
•
Car battery cord
(Supplied)
ANT.
DC 13.2V
DC13.2V
ANT.
AUDIO OUT
R
COAXIAL
EN
–
–
11
0C28
CONNECTING TO A STEREO SYSTEM
Stereo system
DC 13.2V
L
AUDIO OUT
R
ANT.
L
AUDIO OUT
R
COAXIAL
COAXIAL
To ANALOG AUDIO INPUT jacks
To Right (red) and Left (white)
AUDIO OUT jacks
[Fig. 7]
NOTES:
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner's Manuals for your, stereo system and any other components to be connected to the
TV/DVD.
•
•
The monaural sound is output from the stereo system when the TV/DVD is in the TV mode.
•
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL
INPUT JACKS, MD DECK OR DAT DECK (for DVD only)
Use an audio coaxial digital cable available at retail for the audio connections.
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
DC 13.2V
L
AUDIO OUT
R
ANT.
L
AUDIO OUT
R
COAXIAL
COAXIAL
To COAXIAL DIGITAL
AUDIO INPUT jack
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
(only DVD AUDIO OUT)
[Fig. 8]
NOTES:
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
•
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner's Manuals for the components to be connected to the TV/DVD.
Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD using incorrect set-
tings may generate noise distortion, and may also damage the speakers. (See page 27 to set DOLBY
DIGITAL to OFF.)
•
•
•
EN
–
–
12
0C28
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)
If using this TV/DVD to play a DVD disc in a 5.1 channel Dolby Digital surround format, the TV/DVD out-
puts a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the player up to
a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality
surround sound as enjoyed in movie theaters.
Use audio coaxial digital cables available at retail for the audio connections.
Center
speaker
Front speaker
(left)
Front speaker
(right)
DC 13.2V
L
Dolby Digital decoder
To COAXIAL DIGITAL
AUDIO INPUT jack
AUDIO OUT
R
ANT.
L
AUDIO OUT
R
COAXIAL
COAXIAL
Subwoofer
Surround
speaker
(left)
Surround
speaker
(right)
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
[Fig. 9]
NOTES:
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner's Manuals for the components to be connected to the TV/DVD.
If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.
(See page 27 to set DOLBY DIGITAL to ON.)
•
•
•
Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup
mode. Playing a TV/DVD using incorrect settings may generate noise distortion, and may also damage the
speakers.
•
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
EN
–
–
13
0C28
TV SECTION
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just
select the TV/DVD channel selector to the output channel of the cable box or satellite box (Ex CH3). Then
select the channel to be viewed on the Cable Box or Satellite Box.
CHANNEL SET UP FOR THE
FIRST TIME
DELETING (OR ADDING)
CHANNEL
TV
TV
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you can
add the deleted channel into the memory again.)
1 Plug in the TV/DVD power cord
Plug the TV/DVD power cord into a
standard AC outlet.
NOTE:
- TV SETUP -
1 Select “CHANNEL SET UP”
Press SETUP on the remote control.
Press K or L to point to “CHAN-
NEL SET UP”.
If some digits appear in the corner of
the screen, press POWER without
unplugging the power cord.
•
B
CHANNEL SET UP
LANGUAGE [ENGLISH]
2 Turn on the TV/DVD
Press POWER to turn on the TV/DVD.
Then, press ENTER.
2 Select “ADD/DELETE CH”
Press K or L to point to
“ADD/DELETE CH”.
– CHANNEL SET UP –
B
ADD / DELETE CH (TV)
AUTO PRESET
3 Select the On Screen
Language
Press K or L to point to “LAN-
GUAGE”.
– SET UP –
LANGUAGE
B
Then, press ENTER.
[ENGLISH] ESP
FRA
AUTO PRESET
Then, press ENTER to select
“ENGLISH” or “ESP”=Spanish or
“FRA” =French. “[ ]” indicate the selected language.
3 Enter the desired channel number
Press K or L until your desired
channel number appears. (You can
also use Number or CH. K/L to
enter it.) (Example: CH8)
08
– SET UP –
4 Begin auto preset
Press K or L to point to “AUTO
ADD / DELETE
LANGUAGE
[ENGLISH] ESP
FRA
PRESET”. Then, press ENTER.
The tuner scans and memorizes all
active channels in your area.
B
AUTO PRESET
4 Delete (or add) it from (into) memory
Press ENTER. The channel number changes to light
red. The channel is deleted from memory.
NOTES:
The TV/DVD distinguishes between standard TV
channels and cable(CATV) channels.
•
Added channel: Light blue.
Deleted channel: Light red.
The TV/DVD may memorize TV channels as
CATV channels if reception conditions is poor. If
this happens, try AUTO PRESET action again
when reception conditions are better. See “CHAN-
NEL SET UP AGAIN” on page 15.
•
To delete another channel, repeat steps [3] and [4].
If you press ENTER again, the channel is memo-
rized again.
•
•
5 After scanning
5 Exit the channel setup mode
Press SETUP on the remote control to returns to TV
mode.
NOTE: To confirm that channel(s) has been deleted
or added, press CHANNEL(CH.) K or L.
The tuner stops on the lowest memorized channel.
If you want to recall the selected channels, you can
select the desired channel directly with Number or
CHANNEL(CH.) K or L.
EN
–
–
14
0C28
CHANNEL SET UP AGAIN
TV
- TV SETUP -
1 Select “CHANNEL SET UP”
Press SETUP on the remote control.
Press K or L to point to “CHAN-
NEL SET UP”.
B
CHANNEL SET UP
LANGUAGE [ENGLISH]
Then, press ENTER.
2 Begin auto preset
– CHANNEL SET UP –
Press K or L to point to “AUTO
PRESET”. Then, press ENTER.
The tuner scans and memorizes all
the active channels in your area.
NOTES:
ADD / DELETE CH (TV)
AUTO PRESET
B
The TV/DVD distinguishes between standard TV
channels and cable(CATV) channels.
•
The TV/DVD may memorize TV channels as
CATV channels if reception conditions is poor. If
this happens, try AUTO PRESET action again
when reception conditions are better.
•
3 After scanning
The tuner stops on the lowest memorized channel.
SELECTING THE LANGUAGE
TV
NOTE: This function effects only the language on
the screen menu and not the audio source.
- TV SETUP -
1 Select “LANGUAGE”
Press SETUP on the remote control.
Press K or L to point to “LAN-
GUAGE”.
CHANNEL SET UP
LANGUAGE [ENGLISH]
B
Then, press ENTER to select
“ENGLISH” or “ESPAÑOL”=
Spanish or “FRANÇAIS”= French.
2 Exit the Language mode
Press SETUP on the remote control to return to TV
mode.
NOTE: If Spanish or French is selected accidentally,
1)Press SETUP on the remote control.
2)Press K or L to point to “IDIOMA [ESPAÑOL]”
or “LANGAGE” [FRANÇAIS].
3)Press ENTER to select your desired language.
4)Press SETUP to exit.
EN
–
–
15
0C28
TV OPERATION
WATCHING A TV PROGRAM
PICTURE CONTROL
TV
TV
The TV/DVD’s picture controls – BRIGHT, CON-
TRAST, COLOR, TINT and SHARPNESS – are
preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a natural looking image.
1 Turn on the TV/DVD
Press POWER to turn on the TV/DVD.
2 Select the channel number
Press CHANNEL(CH.) K or L to select your desired
channel number or press Number on the remote con-
trol.
Make sure ...
TV/DVD power must be turned on.
•
Note for using the Number on the remote control:
¡When selecting cable channels which are higher
than 99, press +100 first, then, press the last two
digits. (Example: to select channel 125, first press
“+100” then press “2” and “5”).
1 Select “PICTURE CONTROL”
Press PICTURE on the remote control.
¡You must precede single-digit channel numbers
with a zero (For example: 02, 03, 04 and so on).
Remember:
¡If the TV/DVD is connected to a cable box or
satellite box, the TV/DVD must be on CH3 or
CH4, then the channel to be viewed must be select-
ed on the cable box or satellite box.
2 Select item you want to adjust
Press K or L until desired control is displayed.
BRIGHT
CONTRAST
COLOR
TINT
BRIGHT
–
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +
SHARPNESS
3 Adjust sound
X
Y
Press VOLUME(VOL.) or to
3 Adjust the picture control
adjust the volume.
Press B or s to adjust to your desired level within
VOLUME 20
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
5 seconds.
NOTE:
NOTE:
At step 3, the picture adjustment display will disap-
If you press the CHANNEL(CH.) o or p in the
DVD mode, you can change the TV channels.
Even if you turn off the TV/DVD in the DVD
mode, when you turn it on again, it will go into the
TV mode.
•
•
pear from the TV screen after about 5 seconds
unless you press any buttons, even though you may
not be finished. In this case, repeat from step [1].
s
B
BRIGHT
to decrease
brightness
to decrease
contrast
to increase
brightness
to increase
contrast
DEGAUSSING
Magnetism from nearby appliances and speakers
might affect the color of the TV picture.
If this happens, move this unit away from the appli-
ance. If the color is still not correct, disconnect power
cord from AC outlet then reconnect it after 30 minutes.
CONTRAST
COLOR
TINT
SHARPNESS to soft
to pale
to brilliant
to purple
to green
to clear
If there is a power failure of any kind, the unit will
retain its memory for this feature.
•
EN
–
–
16
0C28
SLEEP TIMER
TV
he Sleep Timer function enables you to shut off the power
T
without pressing POWER after a desired time period.
1 Set “SLEEP TIMER”
Press SLEEP on the remote control.
You may change the sleep time
with pressing SLEEP on the remote
control repeatedly. The timer is set
SLEEP 120 MINUTE
up to 120 minutes, 30 minutes each
time SLEEP is pressed.
To cancel the sleep timer:
Press SLEEP repeatedly until "SLEEP 0 MINUTE"
is displayed.
NOTES:
When you disconnect the unit from the AC outlet,
or if you have a power failure, the sleep time will
be lost.
•
To view the time left for sleep timer press SLEEP
once when SLEEP display disappears. After 10
seconds, display will disappear again.
•
EN
–
–
17
0C28
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS
DISC TYPES
The following discs can be played back on this TV/DVD.
[
]
DVD
Data on a DVD is divided into sections called "titles", and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs, and these playback con-
ditions take priority over user operations on this player. If
a function you selected does not run as desired, refer to
the manual accompanying the disc.
¡
¡
¡
¡
¡
¡
DVD video
DVD+R/RW*
CD-R/RW*
DVD-R/RW*
Audio CD
MP3*
* Depending on the types or the writing method of the
medium some discs can not be played.
• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs
made on personal computers, or on DVD recorders may
not be played back properly due to the factors such as
scratches, dirt or special properties of the disc.
• Discs made on personal computers may not be played
back properly due to the different environment or the
settings of the application you use. We recommend
always to use the standardized, rightly formatted discs.
(Please contact the sales agency for more detail).
Example
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
This player conforms to the NTSC color system. You can-
not play discs recorded in other color systems such as
PAL or SECAM.
[
]
AUDIO CD
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
¡Some discs include region codes as shown below.
Example
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
¡The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format
can only be played back on TV/DVD with the same
region code.
The following discs cannot be played back on this
TV/DVD.
[
]
MP3
Data on an MP3 is divided into sections called "groups",
and then into subsections called "tracks", each of which is
given a group or track number.
¡
DVD with region codes other than 1 or ALL.
¡
¡
DVD-ROM
Example
DVD-RAM (Never play back, otherwise malfunc-
tion may result.)
Group 1
Group 2
¡
¡
¡
¡
¡
Track 1
Track 2
Track 3
Track 4
Track 1
Track 2
CD-ROM
VSD
CDV (Only plays back the audio part.)
CD-G (Only plays back the sound.)
CD-I (Never play back, otherwise malfunction
may result.)
¡
¡
SACD
Photo CD (Never play back, otherwise malfunc-
tion may result.)
¡
Video CD (Never play back, otherwise malfunc-
tion may result.)
Any other discs without compatibility indications.
EN
–
–
18
0C28
PLAYING A DISC
BASIC PLAYBACK
GENERAL FEATURES
DVD may contain menus to navigate the disc and
access special features. Press appropriate numerical
key or use Arrow (L/K/B/s) to highlight your selec-
tion in the DVD main menu and press ENTER to con-
firm.
DVD-V
CD
Getting started
¡Turn on the power of amplifier and any other com-
ponents, if necessary.
NOTES
¡Select DVD mode by pressing SELECT on the
remote control. Then, press PLAY or OPEN/CLOSE
before you operate the DVD functions.
1
Press POWER.
¡The power will turn on.
2
3
Press OPEN/CLOSE to open disc loading
tray.
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
Place the chosen disc in the tray, with the
label facing up.
DISC MENU
DVD-V
1
Press DISC MENU.
¡The DVD main menu will appear.
2
3
If the feature is not available,
may appear on the TV screen.
symbol
4
Press PLAY.
¡The tray will close automatically, and playback will
then start from the first chapter or track of the disc.
If the playback does not start automatically, press
PLAY.
If disc menu is available on the disc, audio
language, subtitle options, chapters for the
title and other options will appear for selec-
tion.
¡When you playback the DVD which a title menu is
recorded, it may appear on the screen. In this case,
refer to “TITLE MENU”.
4
Press Arrow (L/K/B/s) to select an item,
and ENTER to confirm selection.
5
Press STOP to stop playback.
TITLE MENU
NOTES
DVD-V
¡When the DVD mode has been switched to the TV
mode, the DVD mode shuts down first and then TV
picture and sound appears in about 4 seconds.
Similarly, when POWER is pressed to turn off in the
DVD mode, this mode shuts down first and then the
TV/DVD’s power is turned off.
¡A “prohibited icon” may appear at
the top-right on the TV screen dur-
ing operation, warning that a pro-
hibited operation has been encoun-
1
Press TITLE.
¡The title menu will appear.
2
3
If the feature is not available,
may appear on the TV screen.
symbol
Press Arrow (L/K/B/s) to select an item,
and ENTER to confirm selection.
tered by the DVD or the disc.
¡With DVDs that use titles for playback program sig-
nals, playback may start from the second title, or it
may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
CALLING UP A MENU SCREEN
DURING PLAYBACK
For DVD-Vs
¡Press DISC MENU to call up the DVD menu.
¡Press TITLE to call up the title menu.
NOTE
¡Contents of menus and corresponding menu opera-
tions may vary between discs. Refer to the manual
accompanying the disc for details.
EN
–
–
19
0C28
SLOW FORWARD /
SLOW REVERSE
RESUME
DVD-V
CD
DVD-V
1
During playback, press STOP.
¡Resume message will appear on the TV screen.
1
2
3
During playback, press PAUSE.
Press FWD g or REV h .
2
Press PLAY, playback will resume from the
point at which playback was stopped.
Press FWD g or REV h repeatedly to
select the required speed: 1/16, 1/8, 1/2 of
the normal playback.
¡To cancel resume, press STOP twice.
¡If turn off the TV/DVD, resume function will be
cancelled.
4
To return to normal playback, press PLAY.
Note for using buttons on the main unit:
Press PAUSE, then, press and hold down the SKIP G/
SEARCHg or SKIPH /SEARCHh on the
TV/DVD for a few seconds to begin Search in 1/16
speed of the normal playback. Press and hold down
again to change speed to 1/8. Repeat this procedure to
change to 1/2.
PAUSE
DVD-V
CD
1
During playback, press PAUSE.
¡Playback will pause and sound will be muted.
2
To continue playback, press PLAY.
ZOOM
STEP BY STEP PLAYBACK
DVD-V
DVD-V
The Zoom function allows you to enlarge the video
image and to pan through the enlarged image.
1
During playback, press PAUSE.
¡Playback will pause and sound will be muted.
1
Press ZOOM during playback.
¡Playback will continue.
2
3
The disc goes forward by one frame each
time PAUSE is pressed.
2
Press ZOOM repeatedly to select the
required zoom factor: ZOOM1, ZOOM2,
ZOOM3, or OFF.
To exit step by step playback, press PLAY.
FAST FORWARD/REVERSE
SEARCH
3
4
Use the Arrow (K/L/s / B) to move the
zoomed picture across the screen.
DVD-V
CD
MP3
To exit zoom mode, press ZOOM to OFF.
NOTES
1
During playback, press FWD g or REV
repeatedly to select the required forward or
reverse speed: x2, x8, x50, x100.
h
¡Zooming function does not work while disc menu is
shown.
¡Zooming function is not available on some discs.
¡For audio CDs, the speed is fixed at ×16.
¡For MP3, the speed is fixed at ×8.
2
To return to normal playback, press PLAY.
Note for using buttons on the main unit:
During playback, press and hold down the SKIP G /
SEARCHg or SKIPH /SEARCHh on the
TV/DVD for a few seconds to begin Search in x2
speed. Press and hold down again to change speed to
x8. Repeat this procedure to change to x50 and x100.
EN
–
–
20
0C28
SEARCH FUNCTION
TRACK SEARCH
TIME SEARCH
CD
DVD-V
CD
There are three ways to begin playback on an Audio
CD at a specific Track.
1
2
During playback, press SEARCH MODE
three times (CD: twice) to display the Time
Search on the TV screen.
Using Number on the remote control
Within 30 seconds, enter a desired disc
time using Number on the remote control.
1
Press Number to enter the desired Track
number.
¡Playback will start at the specified time.
¡Press CLEAR to erase the incorrect input.
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
¡To play track 26, press +10, 2, 6.
MARKER SETUP SCREEN
DVD-V
CD
Using SEARCH MODE
1
Press SEARCH MODE.
¡The track search display appears.
Use markers to memorise your favorite places on a
disc.
2
Within 30 seconds, select a desired track
number using Number on the remote control.
1
Press SEARCH MODE four times (CD: three
times) during playback.
¡For single digits press 0 first.
¡Playback will start at the selected track.
¡The display screen and Markers will appear on the
TV screen.
Using SKIP
H
G
During playback, press SKIP G to move the next
track. Press it repeatedly to skip subsequent tracks.
Press SKIP H to go back to beginning of the current
track. Press it repeatedly to go to the previous tracks.
¡If SKIP is pressed while the playback is paused, the
playback will be paused again after skipping to the
next track.
2
3
Press Arrow (s /B) to select 1, 2, 3, 4, 5, 6,
7, 8, 9, or 10 and ensure that “- : - - : - -”
appears in the display.
When reaches the desired point, press
ENTER.
¡The Title or Track and elapsed playing time will
appear in the TV screen.
NOTE
¡SKIP
H
G are not available when playback is
stopped.
4
To return to the Marker later, press SEARCH
MODE four times (CD: three times) during
playback and Arrow (s /B) to choose the
desired marker, then press ENTER.
TITLE / CHAPTER SEARCH
NOTES
DVD-V
¡Opening the disc tray or turning off the power or
select AC at step 2 and press ENTER will erase all
Markers.
¡To clear a marker, using Arrow (s /B), position the
cursor on to the marker number to be cleared and
press CLEAR.
1
Press SEARCH MODE once for the Chapter
search, twice for the Title search during
playback.
/2
¡You can mark up to 10 points.
5
Press SEARCH MODE or RETURN to exit.
2
Enter the desired chapter/title number using
Number on the remote control.
¡Playback will start at the selected Chapter or Track.
¡Press CLEAR to erase the incorrect input.
¡For single digits press 0 first.
EN
–
–
21
0C28
SPECIAL PLAYBACK FUNCTION
REPEAT
PROGRAM
REPEAT is available only during playback.
CD
REPEAT TITLE / CHAPTER
You may determine the order in which tracks will play.
DVD-V
1
In stop mode, press MODE.
¡The PROGRAM screen will appear.
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
2
Press L or M to select a track, then press
ENTER.
CHAPTER
(current chapter repeat) (current title repeat)
TITLE
OFF
(repeat off)
¡Press CLEAR to erase the
most recently entered pro-
gram.
TOTAL
NOTES
¡Repeat Title/Chapter is not available with some
scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
3
4
Repeat step 2 until you have selected all the
tracks you want to play in the program.
Press PLAY to play the programmed tracks.
NOTES
REPEAT TRACK
CD
¡While the program is being played back, the STOP
works as follows.
¡Press STOP once and then PLAY again, playback
will restart from the point where STOP was pressed.
(Program continued)
¡Press STOP twice and then PLAY again, playback will
restart from the track in the usual way. (Program cleared)
¡Up to 99 programs can be entered.
¡If you like to repeat the current track in the program,
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
TRACK
(current track repeat)
ALL
OFF
(repeat off)
(entire disc repeat)
press REPEAT repeatedly until
TRACK appears
during playback. If you like to repeat the entire pro-
NOTES
gram press REPEAT repeatedly until
appears during playback.
ALL
¡Repeat setting will be cleared when moving to other
track.
¡Repeat playback does not function during repeat A-
B playback.
RANDOM PLAYBACK
REPEAT A-B
CD
DVD-V CD
This shuffles the playing order of tracks instead of
playback in the sequence.
1
2
Press REPEAT A-B at your chosen starting
point.
A- appears briefly on the TV screen.
¡
¡
1
In stop mode, press MODE twice.
¡RANDOM screen appears.
RANDOM
Press REPEAT A-B again at your chosen
end point.
CD [AUDIO]
TOTAL 0:45:55
RANDOM PROGRAM
- - no indication - -
A-B appears briefly on the TV screen, and the
repeat sequence begins.
PLAY
3
To exit the sequence, press REPEAT A-B.
NOTES
¡The repeat A-B section can only be set within the cur- NOTE
rent title (for DVDs), or current track (for audio CDs). ¡If you like to repeat the current track in the random
2
Press PLAY to start random playback.
¡Repeat A-B is not available with some scenes in DVD.
¡To cancel the A point which was set, press CLEAR.
¡Repeat A-B playback does not function during title,
chapter, track or all repeat playback.
–
selection, press REPEAT repeatedly until
TRACK appears during playback. If you like to
repeat the entire random selection press REPEAT
repeatedly until
ALL appears during playback.
EN
–
22
0C28
PLAYING A MP3 DISC
MP3 PLAYBACK
TRACK SELECTION
MP3
MP3
When a CD with MP3 files is in the TV/DVD, the
MP3 menu will appear on the TV screen in stop mode.
1
Press SEARCH MODE during playback.
¡The FILE LIST will appear.
1
In stop mode, press Arrow (K/L) to select
the desired group track.
2
Select a desired track using Arrow
(K/L/s/B).
¡If a group is selected, press
or ENTER to go on to the
track selection screen. Press
Arrow (K /L ) to choose a
B
¡Press B when you want to go to the next hierarchy.
¡Press s when you want to go back to the previous
hierarchy.
track, then press ENTER.
¡If a track is selected, press
ENTER to start playing
tracks. Starting from the one you’ve just chosen the
subsequent tracks will be played.
¡Choose FIRST PLAY to start playback from the
beginning of the listed tracks.
3
Press PLAY to start playback.
NOTES
¡Press SEARCH MODE to exit.
¡Some selections may take a while to be recognized.
PROGRAM
¡Press TITLE to return to the first item.
MP3
2
Press STOP to stop playback.
NOTES
This feature allows you to program an MP3 disc to
play in a desired sequence.
¡Folders are known as Groups; files are known as
Tracks.
¡MP3 files are accompanied by
3
icon.
¡Maximum of 255 folders can be recognized.
¡Maximum of 256 files can be recognized.
¡Up to 8 hierarchies can be created.
1
In stop mode, press MODE.
¡The PROGRAM screen will appear.
This player recommends the use of files recorded at
the below specifications:
¡Sampling frequency: 44.1kHz or 48kHz
¡Constant bit rate: 112kbps ~ 320kbps.
2
Select a desired track using Arrow
(K/L/s/B). Then, press ENTER.
¡Press B when you want to go to the next hierarchy.
¡Press s when you want to go back to the previous
hierarchy.
¡Press CLEAR to erase the most recently entered pro-
gram.
3
Repeat step 2 until you have selected all the
Tracks you want to play in the program.
4
Press PLAY to start programmed playback.
RANDOM PLAYBACK
MP3
1
In stop mode, press MODE twice.
¡RANDOM screen appears.
2
Press PLAY to start random playback.
EN
–
–
23
0C28
CHANGING THE SETTINGS
SUBTITLE LANGUAGE
CAMERA ANGLE
DVD-V
DVD-V
The DVD allows you to select a language for subtitles Some DVD discs contain scenes which have been shot
during DVD disc (if available) playback. simultaneously from various angles. You can change
the camera angle when the (
screen.
) icon appears on the
1
2
Press SUBTITLE during playback.
Press SUBTITLE repeatedly to select your
desired subtitle language.
1
Press ANGLE during playback.
¡The selected angle will be displayed on the display
¡The subtitle language will be displayed on the dis-
play bar at the top of the screen.
bar at the top of the screen.
2
Press ANGLE repeatedly to select your
desired angle.
3
To turn off subtitles, press SUBTITLE
repeatedly until OFF appears.
NOTES
BLACK LEVEL SETTING
¡
Some discs allow audio language setting/subtitle language
setting on the disc menu. (Operation varies between discs,
so refer to the manual accompanying the disc.)
DVD-V
¡If the desired language is not shown after pressing
SUBTITLE several times, the disc does not have
subtitles in that language.
Adjust the Black Level Settings to make the black
parts of the picture brighter.
¡If you choose a Language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, ‘---’ will be displayed instead.
(Refer to page 26.)
1
Press MODE during playback.
ON
AUDIO LANGUAGE
2
Press ENTER to switch ON/OFF.
ON: Makes the dark parts brighter.
DVD-V
OFF: Shows the original picture as recorded.
The TV/DVD allows you to select a language during
DVD disc (if multi language available) playback.
3
Press MODE twice or RETURN to exit.
VIRTUAL SURROUND
1
2
Press AUDIO during playback.
Press AUDIO repeatedly to select your
desired language.
DVD-V
CD
MP3
NOTE
You can enjoy stereophonic visual space on your exist-
ing stereo system.
¡Pressing AUDIO may not work on some DVDs with
multiple audio languages (e.g. DVDs which allow
audio language setting on the disc menu).
1
Press MODE twice (CD/MP3: once) during
playback.
STEREO SOUND MODE
OFF
CD
2
3
Press ENTER to set it 1 (Natural effect) or 2
(Emphasized effect) or OFF.
1
Press AUDIO repeatedly during playback to
select between STEREO, L-CH or R-CH.
¡STEREO - both right and left channels are active
(stereo)
L-CH - only left channel is active
R-CH - only right channel is active
NOTE
Press MODE or RETURN to exit.
NOTE (for CD play only)
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO.
¡If the Virtual Surround setting is ON, the sound
mode will be fixed to STEREO, and can not be
changed.
EN
–
–
24
0C28
THE ON-SCREEN INFORMATION
DVD-V
CD
MP3
You can check the information about the current disc by pressing DISPLAY on the remote control.
For DVD-Vs
For audio CDs
1
Press DISPLAY during playback to show
current Chapter.
1
Press DISPLAY during playback to show
the current Track.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
9/49
0:00:00 -0:00:00
2
Press DISPLAY again to show current Total
Track.
2
Press DISPLAY again to show current Title.
¡The elapsed and remaining playing time of the cur-
¡The elapsed and remaining playing time of the cur-
rent total track will be displayed.
rent title will be displayed.
3
Press DISPLAY again.
¡The BIT RATE and the current repeat setting will be
displayed.
3
Press DISPLAY again to exit the display.
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
For MP3
1
Press DISPLAY during playback.
¡The name of the file currently in play will be dis-
4
Press DISPLAY again to exit the display.
played.
2
Press DISPLAY again to show the track
number, the repeat status, and the playback
status at the top of the screen.
¡
will be displayed when repeat play has been
selected.
T - indicates Track repeat
G - indicates Group (folder) repeat
A - indicates Disc repeat
3
Press DISPLAY again to exit the display.
EN
–
–
25
0C28
CHANGING THE DVD SETUP ITEMS
LANGUAGE SETTING
Language
Code Language
Code
DVD-V
A-B
L-N
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
4748 Laothian
4747 Latin
4752 Latvian;Lettish
6563 Lingala
4759 Lithuanian
4764 Macedonian
5471 Malagasy
4765 Malay
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
Language options are not available with some discs.
1
Press SETUP twice in STOP mode so that
the DVD SETUP menu appears.
¡If the menu does not appear, press PLAY, STOP,
4771 Malayalam
4772 Maltese
4847 Maori
then SETUP twice.
5167 Marathi
4860 Moldavian
5072 Mongolian
4854 Nauru
QUICK SETUP
TV MODE
DOLBY DIGITAL ON
4:3 LETTER BOX
4855 Nepali
4864 Norwegian [NOR]
4853
5971 Occitan
4851 Oriya
Oromo(Afan)
5759 Panjabi
4947 Pashto;Pushto
7254 Persian
4961 Polish
5464 Portuguese [POR]
4965 Quechua
5047 Rhaeto-Romance
6058 Romanian [RUM]
5160 Russian [RUS]
5161
5166 Samoan
Sangho
5261 Sanskrit
5256 Scots Gaelic
5255 Serbian
Bulgarian
Burmese
Byelorussian
O-R
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
2
Press B to select CUSTOM, then press
C-E
ENTER.
Cambodian
Catalan
¡CUSTOM mode will appear.
Chinese [CHI]
Corsican
Croatian
3
Press Arrow (s / B) to select LANGUAGE,
Czech
then press ENTER to confirm.
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
S
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
LANGUAGE
F-H
AUDIO
SUBTITLE
DISC MENU
ORIGINAL
OFF
ENGLISH
Faroese
Fiji
Finnish [FIN]
French [FRE]
Frisian
5264 Serbo-Croatian
5271 Sesotho
5358 Setswana
5747 Shona
4
Press Arrow (K/L) to select the next items,
Galician
then press ENTER.
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
AUDIO:
5051 Sindhi
5158 Singhalese
5758 Siswat
5360 Slovak
¡Sets the audio language.
SUBTITLE:
¡Sets the subtitle language.
DISC MENU:
Gujarati
Hausa
Hebrew
5367 Slovenian
5447 Somali
5569 Spanish [SPA]
5455 Sundanese
5467 Swahili
¡Sets the language for DVD menu.
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Swedish [SWE]
5
Press Arrow (K/L) to select a setting, then
5565
5560 Tagalog
5547 Tajik
5551 Tamil
5557 Tatar
5347 Telugu
5566 Thai
T
press ENTER.
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
¡If OTHER is selected on the AUDIO, SUBTITLE or
DISC MENU screen, press four-digit number to
enter the code for the desired language. (Refer to the
language code list below.)
¡Only the languages supported by the disc can be
selected.
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
5647 Tibetan
5669 Tigrinya
5760 Tonga
5765 Tsonga
5757 Turkish [TUR]
6469 Turkmen
5771 Twi
Kazakh
Kinyarwanda
Kirghiz
Kirundi
6
Press SETUP to exit.
NOTE
6460
U-Z
¡Language Setting for Audio and Subtitle is not avail-
able with some discs. Then use the AUDIO and the
SUBTITLE button. Details are on page 24.
Korean [KOR]
Kurdish
5761 Ukrainian
5767 Urdu
Uzbek
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
TO CHANGE THE ON-SCREEN MENUS
You can access the TV SETUP menu by pressing
SETUP from the DVD mode. Refer to “Selecting the
Language” on page 15 to changing the on-screen
menus.
¡In case of selecting from the DVD mode, you cannot
select “CHANNEL SET UP” menu.
Yoruba
Zulu
If you choose a Language that has a 3 letter language
code, the code will be displayed every time you change
the Audio or Subtitle language setting on page 24. If
you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
EN
–
–
26
0C28
DISPLAY SETTING
AUDIO SETTINGS
Choose the appropriate Audio settings for your equip-
ment as it only affect during the playback of DVD
discs.
DVD-V
You can change certain aspects of the DVD display
screens and on-screen messages on the TV screen.
1
Press SETUP twice in STOP mode so that
the DVD SETUP menu appears.
1
Press SETUP twice in STOP mode so that
the DVD SETUP menu appears.
¡If the menu does not appear, press PLAY, STOP,
¡If the menu does not appear, press PLAY, STOP,
then SETUP twice.
then SETUP twice.
QUICK SETUP
TV MODE
4:3 LETTER BOX
DOLBY DIGITAL ON
QUICK SETUP
TV MODE
4:3 LETTER BOX
DOLBY DIGITAL ON
2
Press B to select CUSTOM, then press
ENTER.
2
Press B to select CUSTOM, then press
ENTER.
¡CUSTOM mode will appear.
¡CUSTOM mode will appear.
3
Press Arrow (s /B) to select AUDIO, then
press ENTER to confirm.
3
Press Arrow (s /B) to select DISPLAY, then
press ENTER to confirm.
AUDIO
DRC
OFF
ON
DOLBY DIGITAL
DISPLAY
DOWN SAMPLING ON
TV MODE
4:3 LETTER BOX
ON
ANGLE ICON
AUTO POWER OFF ON
4
Press Arrow (K/L) to select the below
items, then press ENTER.
DRC (Dynamic Range Control):
¡To compress the range of sound volume.
¡The default setting is OFF.
4
Press Arrow (K/L) to select the below
items, then press ENTER.
TV MODE:
QUICK
¡Press Arrow (K/L) for an item selection, then press
ENTER.
¡Select 4:3 LETTER BOX for a black bars appears
on top and bottom of the screen.
¡Select 4:3 PAN & SCAN for a full height picture
with both sides trimmed.
¡The default setting is 4:3 LETTER BOX.
DOLBY DIGITAL:
Set to On when the unit is connected to a Dolby Digital
Decoder.
(ON: Output by Dolby Digital)
(OFF: Convert the Dolby Digital to PCM (2 channel
stereo))
QUICK
¡The default setting is ON.
ANGLE ICON:
DOWN SAMPLING:
¡Set to ON when outputting in 48 kHz.
¡The default setting is ON.
When playing disc with copyright Protection
¡If you select OFF, copyright protection will be acti-
vated and sound will be down sampled at 48kHz.
¡Press ENTER repeatedly to turn Angle icon ON or
OFF.
¡The default setting is ON.
AUTO POWER OFF:
¡Press ENTER repeatedly to turn Auto Power off ON
or OFF.
5
Press SETUP to exit.
¡The default setting is ON and it will turn the
TV/DVD to off automatically after 15 minutes of no
use.
5
Press SETUP to exit.
EN
–
–
27
0C28
PARENTAL CONTROL
CONTROL LEVELS
DVD-V
¡
ALL
All parental lock is cancelled.
Parental Control limits the disc viewing that exceed
your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alterna-
tive scenes from being played by your children.
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
¡
Levels 7 to 2
PARENTAL LEVEL
Only DVD software intended for general use and
children can be played back.
¡
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s rat-
ings exceed the level you set.
Level 1
1
Press SETUP twice in STOP mode so that
the QUICK SETUP menu appears.
¡If the menu does not appear, press PLAY, STOP,
then SETUP twice.
IF YOU FORGET THE PASSWORD
QUICK SETUP
1
Press 4, 7, 3, 7 at step 4. Then enter your
new password.
TV MODE
4:3 LETTER BOX
DOLBY DIGITAL ON
¡Password will be cleared and parental level will be
set to ALL.
2
3
Press B to select CUSTOM, then press
ENTER.
2
Proceed the above Steps 5-7 again.
Press Arrow (s/B) to select PARENTAL,
then press ENTER.
PARENTAL
PARENTAL LEVEL ALL
4
5
6
7
Enter your four-digit password then press
ENTER.
Press Arrow (K/L) to select PARENTAL
LEVEL, then press ENTER.
Press Arrow (K/L) to select the desired
level.
Press SETUP to exit
NOTES
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the
password from the second time onward.
¡To change the password, press Arrow (K/L) to
select CHANGE at step 5, then press ENTER. Enter
the four-digit pass-word, then press ENTER.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
¡Record the password in case you forget it.
EN
–
–
28
0C28
TROUBLESHOOTING GUIDE
If the TV/DVD does not perform properly when operated as instructed in this Owner’s Manual, check the
player, consulting the following checklist.
Problem
Corrective Action
Make sure the power plug is connected to an AC outlet.
Make sure the power is turned on.
Check if the power plug is connected to an AC outlet.
Check the batteries in the remote control.
Aim the remote control directly at the remote sensor. If necessary,
remove all the obstacles between the sensor and the remote.
You have to be within 23 feet of the TV/DVD.
No power.
•
•
•
•
•
The TV/DVD does not respond to
the remote control.
•
•
Check if the correct mode is selected. If not switch the mode by
pressing SELECT on the remote control,whichever you need.
TV Mode
Problem
Corrective Action
No Picture or Sound
Try a new channel, if OK, then possible station trouble.
Make sure the power is turned on.
Press SELECT on the remote control to select TV mode. Then try
other TV feature.
•
•
•
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
If outside antenna is being used, check for broken wire.
Try a new channel, if OK, then possible station trouble.
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Adjust COLOR control.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Adjust CONTRAST & BRIGHT control.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Bars On Screen
Picture Distorted or Blurred
Picture Rolls Vertically
Lines or Streaks in Picture
No Color
Poor Reception on Some Channels
Ghosts in Picture
Weak Picture
Sound OK, Picture Poor
Adjust CONTRAST & BRIGHT control.
Try a new channel, if OK, then possible station trouble.
Check for local interference.
Magnetism from nearby appliances and geomagnetism might affect
the color of the TV picture. Move the TV/DVD away from the appli-
ances, the TV/DVD can repair itself automatically. If you want to
repair immediately, unplug the TV/DVD power cord, then plug it in
again 30 minutes or so later.
Picture OK, Sound Poor
Different color marks on screen.
EN
–
–
29
0C28
DVD Mode
Problem
Corrective Action
• Connect the video cables firmly.
No picture.
• Insert a correct video disc that plays on this TV/DVD.
• Press SELECT on the remote control to select DVD mode. Next,
press PLAY or OPEN/CLOSE. Then, try other DVD feature.
• Insert the disc.
.
Disc cannot be played
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
.
No sound
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This TV/DVD does not support DTS audio. This is not a malfunction.
.
No DTS audio is output
.
•
There are some cases where pictures may be slightly distorted, which are not a
sign of a malfunction.
Distorted picture
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language
does not match the set up
•
The selected language is not available for audio or subtitles on the DVD.
This is not a malfunction
The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera
angles. This is not a malfunction
Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected
changed
language. This is not a malfunction.
“Prohibited icon” appears on the
screen, prohibiting an operation
CD sound dropout
• That operation is prohibited by the player or the disc.
This is not a malfunction.
• Scratched disc. Replace the disc with unscratched one.
No CD reproduction
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
NOTES:
Some functions are not available in specific modes, but this is not a malfunction. Read the description in
this Owner’s Manual for details on correct operations.
•
Playback from a desired track and random playback are not available during program playback.
•
EN
–
–
30
0C28
MAINTENANCE
CABINET CLEANING
SERVICING
Wipe the front panel and other exterior surfaces of
the TV/DVD with a soft cloth immersed in luke-
warm water and wrung dry.
Never use a solvent or alcohol. Do not spray insec-
ticide liquid near the TV/DVD. Such chemicals
may cause damage and discoloration to the
exposed surfaces.
Should your TV/DVD become inoperative, do not
try to correct the problem by yourself. There are no
user-serviceable parts inside. Turn off, unplug the
power cord, and please call our help line at 1-800-
968-3429, to locate an Authorized Service Center.
•
•
•
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
If the player still does not perform properly when it is operated while referring to the relevant sections and to
"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult
your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
•
DISC HANDLING
Use discs which have the following logos on them.
(Optical audio digital discs.)
•
To clean-off, use a soft cloth.
Do not use a hard cloth since this will mar the disc.
Wipe the disc in a straight line from center to edge.
Never wipe with a circular motion.
•
•
•
•
•
ReWritable
Recordable
Do not use detergent or abrasive cleaning agents.
Handle the discs so that fingerprints and dust do
not adhere to the surfaces of the discs.
•
Always store the disc in its protective case when it
is not used.
•
EN
–
–
31
0C28
SPECIFICATIONS
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
Sound output:
2 speakers, 1W, 8 ohm
TV
CRT :
9 inch in-line gun,
90˚ deflection tube
NTSC-M
OTHER SPECIFICATIONS
Terminals
Television system:
Antenna input:
VHF/UHF/CATV
TV Standard
75 ohm unbalanced (F-type)
RCA connector [ 1
RCA connector [ 2
Closed caption system: §15.119/FCC
Channel coverage:
Video input:
Audio L/R input:
Headphone:
Coaxial digital
audio output
(only DVD):
VHF:
UHF:
CATV:
2 ~ 13
14 ~ 69
2 ~13, A ~ W,
W+1 ~ W+84,
A-5 ~ A-1, 5A
181 channel
1/8” stereo (3.5 mm)
One pin jack,
500m Vpp (75 ohm)
Tuning System:
Channel access:
Analog audio L/R
output:
Remote control:
frequency synthesized
tuning system
Direct access keyboard,
programmable
scan and up/down
RCA connector [ 2
Digital encoded
infrared light system
Operating
temperature:
5°C to 40°C
(41°F~104°F)
Power requirement : AC 120V/60Hz
DC 13.2V
Power consumption : AC 55W / DC 60W
(Maximum)
DVD
Dimensions:
H:12-1/4” (311mm)
W:10-7/8” (276mm)
D:12-1/2” (318mm)
17.6 lbs (8.0 kg)
Discs:
DVD video, Audio CD
Output signal format: NTSC color
Frequency response
Weight:
(output jack)
DVD (linear sound): 20 Hz to 22 kHz
(sample rate: 48 kHz)
20 Hz to 44 kHz
(sample rate: 96 kHz)
20 Hz to 20 kHz
CD:
Signal-to-noise ratio
(S/N ratio)(output jack)
CD:
100 dB (EIAJ)
Dynamic range
(output jack)
DVD (linear sound): 85 dB
CD:
84 dB (EIAJ)
Total distortion factor
CD:
Wow and flutter:
0.07% (EIAJ)
Below the measurement
limitation (+/-0.001%
W PEAK) (EIAJ)
Designs and specifications are subject to change without notice.
If there is a discrepancy between languages, the default language will be English.
•
•
EN
–
–
32
0C28
Botón SEARCH (REV) h (panel delantero)
Durante la reproducción o en el modo de pausa,
mantenga presionado el botón durante unos
segundos para cambiar la velocidad de
reproducción hacia atrás.
INDICE
ꢀ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 33
PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 33
MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 33
VISTA POTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 34
ꢀ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 34
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 34
LA ANTENA INTERIOR . . . . . . . . . . . . . . . . . . . . . . . . 35
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 35
ꢀ CONEXION MOVIL . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 36
CONEXIÓN A UN AMPLIFICADOR EQUIPADO CON
TOMAS DE ENTRADA DIGITAL, PLATINA MD O
10. Botón PLAY
Inicia la reproducción del contenido del disco.
Púlselo para cambiar a un modo de DVD cuando
esta en el modo de televisor.
11. Botón SKIP G
Reproduce desde el inicio del siguiente capítulo
o canción.
Botón SEARCH (FWD) g (panel delantero)
Durante la reproducción o en el modo de pausa,
mantenga presionado el botón durante unos
segundos para cambiar la velocidad de
reproducción en avance.
PLATINA DAT (Para DVD) . . . . . . . . . . . . . . . . . . . . . . 36
CONEXCIONA UN DECODIFICADOR DOLBY
DIGITAL (Para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
12. Botón PAUSE
TV SECTION
Hace una pausa en la operación del disco.
13. Botón OPEN/CLOSE
ꢀ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 37
SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 37
BORRADO (O AGREGACION) DE CANALES . . . . . . 37
Púlselo para insertar discos en la bandeja o
retirarlos de ella.
DVD SECTION
14. Toma HEADPHONE
ꢀ REPRODUCCIÓN DE UN DVD DE VÍDEO O UN
CD DE AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
REPRODUCCION BASICA . . . . . . . . . . . . . . . . . . . . . . 38
Para conectar auriculares (no suministrados) y
escuchar en privado.
15. Botón MODE
Activa el modo de reproducción programada o el
modo de reproducción aleatoria cuand se
reproducen CDs o MP3.
CONTROLES DE
OPERACIÓN Y FUNCIONES
16. Botones de números
PANEL FRONTAL DEL
TELEVISOR/DVD
Modo del televisor:
Pulse dos dígitos para tener acceso directamente
al canal deseado.
Consulte la figura 1 de la página 8
Recuerde pulsar "0" antes de elegir un canal de
un solo dígito.
MANDO A DISTANCIA
Botón +100
Púlselo para seleccionar canales de televisión por
cable cuyo número sea igual o superior al 100.
Modo DVD:
Consulte la figura 2 de la página 8
VISTA POSTERIOR
Púlselo para introducir el número deseado.
Botón +10
Consulte la figura 3 de la página 8
Púlselo para introducir los números deseados
cuyo número sea igual o superior al 10.
17. Botón SLEEP
1. Bandeja de carga del disco
2. Toma de entrada VIDEO
Conecte aquí la toma de salida de vídeo de una
videocámara o de una videograbadora.
3. Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una
videocámara o de una videograbadora.
4. Botón POWER
Pulse el botón SLEEP para visualizar el
temporizador para dormir y activar la función.
La hora de apagado puede determinarse por el
número de veces que usted pulsa el botón. (0,
30,60,90 o 120 minutos)
18. Botón REV h
Púlselo para conectar y desconectar la alimentación.
5. Botones VOLUME o/p(VOL.m/n)
Púlselos para controlar el nivel del volumen para
el DVD y el televisor.
6. Botones CHANNEL o/p(CH.o/p)
Púlselo para seleccionar el canal memorizado.
Púlselo para cambiar a un modo de televisor
cuando esta en el modo de DVD.
Presione para ver la imagen en DVD en retroceso
rápido. Presione PAUSE y presione este botón para
empezar la reproducción en cámara lenta. Presione
repetidamente este botón para cambiar la velocidad
en avance de la cámara lenta.
Botón FWD g
Presione para avanzar rápidamente en el disco.
Presione PAUSE y presione este botón para
empezar la reproducción en cámara lenta.
Presione repetidamente este botón para cambiar
la velocidad de avance de la cámara lenta.
19. Botón ZOOM
7. Ventanilla del sensor del mando a distancia
8. Botón STOP
Detiene la operación del disco.
9. Botón SKIP H
Expand la Imagen para que llene toda la pantalla.
Reproduce desde el inicio del capítulo o canción actual.
ES
–
–
33
0C28
20. Botón SETUP
NOTA: Retire el cable de alimentación del gancho
para evitar romperlo antes de conectarlo a
una toma de CA convencional.
Púlselo para activar o salir del modo de menús
de televisor o preparación de DVD.
21. Botón TITLE
38. Toma de salida AUDIO L/R
Conéctela a la entrada de audio analógico de un
amplificador o decodificador externo.
39. Toma de salida de audio digital COAXIAL
(DVD Audio solamente)
Visualiza el menú de títulos.
22. Botón CLEAR
Repone un ajuste.
23. Botón DISPLAY
Conéctela a la entrada digital de un amplificador
o decodificador externo.
Modo del televisor:
Púlselo para visualizar el número del canal en la pantalla.
Si lo pulsa de nuevo, el número del canal desaparecerá.
Modo de DVD:
40. Toma de entrada ANT.
Conéctela a una antena, sistema de televisión por
cable o sistema de satélite.
Visualiza el estado actual en la pantalla del
televisor con fines de comprobación.
24. Botón SEARCH MODE
Púlselo para localizar un punto deseado.
25. Botón AUDIO
41. Toma DC 13.2V
Conecte en el cable de batería del coche.
PARA INSERTAR LAS PILAS
1) Abra la cubierta del compartimiento de las pilas
empujando la cubierta del mando a distancia en el
sentido de la flecha.
2) Inserte 2 pilas "AA" en el compartimiento de las
pilas, en el sentido indicado por las marcas de
polaridad (+/-).
Púlselo para seleccionar un idioma de audio o un
modo de sonido deseado.
26. Botón SUBTITLE
Púlselo para seleccionar un idioma de subtítulos deseado.
27. Botón REPEAT
Repite la reproducción del disco, título, capítulo
o pista actual.
3) Vuelva a poner la cubierta.
28. Botón ANGLE
Púlselo para cambiar el ángulo de la cámara y
ver, desde un ángulo diferente, la secuencia que
está siendo reproducida.
NOTAS:
No mezcle pilas alcalinas y de manganeso.
No mezcle pilas viejas y nuevas.
•
•
29. Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
30. Botón RETURN
PREPARACIÓN PARA LA
UTILIZACIÓN
Para volver a la operación anterior.
31. Botón ENTER
Púlselo para establecer un ajuste.
32. Botones de flechas
CONEXIONES DE
ANTENA/CABLE
Modo de televisor:
Púlselo para seleccionar un modo de ajuste desde
el menú que aparece en la pantalla del televisor.
Púlselo para seleccionar o ajustar desde un menú
particular.
Consulte la figura 4 de la página 10
Nota para el instalador de sistemas CATV
Esta nota tiene la finalidad de llamar la atención del
instalador de sistemas CATV para que tenga en
cuenta el Artículo 820-40 del NEC, el cual
proporciona consejos para hacer una conexión a
tierra apropiada y, en particular, especifica que la
tierra del cable deberá estar conectada al sistema de
puesta a tierra del edificio, tan cerca del punto de
entrada del cable como sea posible.
Modo de DVD:
Se utiliza cuando se hacen ajustes mientras se observa
la visualización en una pantalla de televisor.
33. Botón DISC MENU
Visualiza menús en el DVD.
34. Botón SELECT
Púlselo para cambiar a un modo de televisor,
modo de entrada externa o modo de DVD.
NOTA:
NOTA: Cuando seleccione el modo DVD con
este botón, pulse primero PLAY u
Antes de enchufar la antena a la toma ANT.IN del
televisor/DVD, compruebe que la clavija no esté
doblada. Si esta doblada, póngala derecha como se
muestra en la ilustración, y luego conéctela en la
toma ANT.IN del televisor/DVD.
OPEN/CLOSE. De lo contrario, las funciones
del DVD no se activarán.
35. Botón MUTE
Pulse el botón MUTE para apagar el sonido de
un programa de TV. (La visualización del nivel
del sonido cambia de ROJO CLARO a AZUL
CLARO.) Pulse de nuevo el botón MUTE o el
botón VOL m o n para restaurar el sonido.
36. Botón PICTURE
Clavija doblada
Cable Clavija
(Necesita enderezarse) (Clavija derecha)
Presione para entrar en el modo de ajuste de imagen.
37. Cable de alimentación
ANTENA COMBINADA DE VHF/UHF
La antena combinada de VHF/UHF de 75 ohmios
puede conectarse al terminal ANT.
Conéctelo a una toma de CA convencional
(120 V/60 Hz).
ES
–
–
34
0C28
NOTA:
Cuando conecte una videograbadora monofónica
(otra fuente) a este televisor/DVD, conecte la toma
de salida de audio de la videograbadora
ANTENA SEPARADAS DE VHF/UHF
En algunas zonas será necesario utilizar una antena
exterior.
•
TELEVICION POR CABLE SIN CAJA
DE CONVERTIDOR / DECODIFICADOR
Utilice esta conexión si su sistema de televisión por
cable se conecta directamente a su televisor/DVD sin
una caja de convertidor. Utilice el mando a distancia
del televisor/DVD para seleccionar los canales.
monofónica (otra fuente) a la toma AUDIO L de
este televisor/DVD. El audio saldrá igualmente por
los canales izquierdo y derecho.
Consulte la figura 6 de la página 11
TELEVICION POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATRLITE
CONEXION MOVIL
ADVERTENCIA: El conductor nunca debe
mirar el TV/DVD mientras conduce un
vehículo.
Si su compañía de televisión por cable le suministra
una caja de convertidor, o si usted utiliza un sistema
de satélite, usted podrá utilizar la conexión básica
mostrada aquí.
PRECAUCION:
Cuando se utiliza en un vehículo en
movimiento, cerciórese que la unidad está
asegurada en todo momento para evitar que
sufra heridas. Consulte con un instalador
profesional.
Si utiliza el TV/DVD con el motor del vehículo
parado, vuelva a cargar la batería del
vehículo después de unas 4 horas de uso
para evitar que se agote. Después de
terminar de utilizar el TV/DVD cerciórese de
desenchufar el cable de batería de coche de
la toma del encendedor de cigarrillos.
No utilice este TV/DVD durante la
conducción.
La selección de los canales deberá hacerse con la caja
de convertidor o con la caja de satélite. Esto significa
que los canales no se podrán cambiar utilizando el
mando a distancia del televisor/DVD.
•
PARA VER UN CANAL
•
CODIFICADO/DECODIFICADO
1) Ponga el selector de canales del televisor/DVD
en la posición del canal de salida de la caja de
convertidor de televisión por cable o de la caja de
satélite. (Ej., CH3)
2) Seleccione el canal que va a ver en su caja de
convertidor de televisión por cable o caja de
satélite.
•
No deje el TV/DVD en un coche.
Este TV/DVD no fue diseñado para utilizar en
un coche.
1) La antena interior entregada es adecuada cuando
el vehículo está estacionado. Para una mejor
recepción en la calle o carretera, utilice una antena
de TV móvil de VHF/UHF de alta calidad.
2) Enchufe el cable de batería de coche en el conec-
tor DC13,2 V (12V) en la parte trasera del
TV/DVD.
•
•
LA ANTENA INTERIOR
La antena interior (suministrada) es desmontable.
Inserte el vástago de la antena en el orificio de la
parte posterior superior del televisor/DVD. Conecte
la antena interior al televisor/DVD. Para obtener la
mejor recepción, extienda completamente la antena
interior y luego haga los ajustes necesarios. (Evite
tocar la sección superior cuando haga los ajustes.)
NOTA:
• La conexión de una antena interior puede no dar
siempre una recepción de TV aceptable.
Para la toma del encendedor
de cigarrillos del vehículo.
Consulte la figura 5 de la página 10
Antena móvil con
combinación de
VHF/UHF (no entregada)
CONEXIÓN A TOMAS DE
ENTRADA EXTERNA
Cuando vea un programa grabado en otra fuente
(videograbadora o videocámara), utilice las tomas de
entrada de audio/vídeo de la parte delantera del
televisor/DVD.
Conecte las tomas de salida de audio/vídeo de otra
fuente a las tomas AUDIO L/R y VIDEO de este
televisor/DVD. Luego pulse SELECT hasta que
aparezca "AUX" en la pantalla.
Cable de batería
de coche
(entregado)
ANT.
DC 13.2V
DC13.2V
ANT.
AUDIO OUT
R
COAXIAL
ES
–
–
35
0C28
NOTAS:
Ponga DOLBY DIGITAL en OFF para la salida de
audio en el modo de preparación. La reproducción
en un televisor/DVD utilizando ajustes incorrectos
puede causar distorsión de ruido, y también se
pueden dañar los altavoces. (Consulte la página 29
para poner DOLBY DIGITAL en OFF.)
•
Cerciórese que su vehículo tiene un sistema eléctri-
co con tierra negativa de 13,2 voltios (12 voltios).
•
Cerciórese de utilizar sólo el cable de batería de
coche entregado. El uso de otros cables puede
dañar el TV/DVD.
•
Cerciórese que la toma está limpia de cenizas y
otros restos.
Cerciórese de enchufar firmemente el cable de
batería de coche en la toma del encendedor de ciga-
rrillos.
Desenchufe siempre la batería del coche de la toma
del encendedor de cigarrillos antes de desenchufar-
lo del TV/DVD.
Debe desconectar el cable de batería de coche del
TV/DVD antes de poder utilizar la electricidad de
CA.
•
CONEXCIONA UN
DECODIFICADOR DOLBY
DIGITAL (Para DVD)
•
Si utiliza este televisor/DVD para reproducir un disco
DVD en un formato de sonido ambiental Dolby
Digital de 5,1 canales, el televisor/DVD dará salida a
un flujo de datos DOLBY DIGITAL desde su toma
de salida de audio digital COAXIAL. Conectando el
reproductor a un decodificador Dolby Digital, usted
podrá disfrutar de un ambiente más convincente y
real, con un sonido ambiental potente y de alta
calidad similar al de los cines.
•
•
Cerciórese de cambiar el fusible sólo por uno del
mismo tipo, 6A, 250V.
•
Utilice cables digitales coaxiales de audio disponibles
en el comercio especializado para hacer las
conexiones de audio.
CONEXIÓN A UN SISTEMA
ESTÉREO
Consulte la figura 9 de la página 13
NOTAS:
Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conector a
otro componente.
Consulte los manuales del propietario de los
componentes que vaya a conectar al televisor/DVD.
Si conecta un decodificador Dolby Digital, ponga
Consulte la figura 7 de la página 12
NOTAS:
Asegrese de desconectar la alimentación de todos
los componentes del sistema antes de conectar otro
componente.
Consulte el manual del propietario de su sistema
estéreo y de cualquier otro componente que vaya a
conectar al televisor/DVD.
Se escucha un sonido monoaural del sistema
estéreo cuando el TV/DVD está en el modo de TV.
•
•
•
•
•
DOLBY DIGITAL en ON para la salida de audio
en el modo de preparación. (Consulte la página 29
para poner DOLBY DIGITAL en ON.)
•
A menos que se haga la conexión a un
•
CONEXIÓN A UN
decodificador Dolby Digital , ponga DOLBY
DIGITAL en OFF para la salida de audio en el
modo de preparación. La reproducción en el
televisor/DVD utilizando ajustes incorrectos puede
generar distorsión de ruido, y también puede
estropear los altavoces.
AMPLIFICADOR EQUIPADO
CON TOMAS DE ENTRADA
DIGITAL, PLATINA MD O
PLATINA DAT (Para DVD)
Utilice un cable digital coaxial de audio de venta en
el comercio especializado para hacer las conexiones
de audio.
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la D
doble son marcas de fábrica de Dolby
Laboratories.
Consulte la figura 8 de la página 12
NOTAS:
La fuente de audio de un disco en un formato de
•
sonido ambiental Dolby Digital de 5,1 canales no
se puede grabar como sonido digital mediante una
platina MD o DAT.
Asegúrese de desconectar la alimentación de todos
los componentes antes de conectar otro
componente.
•
Consulte los manuales del propietario de los
componentes que va a conectar al televisor/DVD.
•
ES
–
–
36
0C28
5 Tras la exploración
TV SECTION
El sintonizador se detiene en el canal memorizado
más bajo. Si desea recuperar los canales
seleccionados, podrá seleccionar los canales
directamente con los botones de números o
CHANNEL(CH.) K o L.
PREPARACIÓN PARA LA
UTILIZACIÓN
Puede programar el sintonizador para explorar todos
los canales que pueda recibir en su zona.
NOTA: La programación de la memoria de canales
no es necesaria cuando se hace la conexión a una caja
de televisión por cable o a una caja de satélite. Ponga
el selector de canales del televisor/DVD en la
posición correspondiente al canal de salida de la caja
de televisión por cable o caja de satélite (ej., CH3).
Luego seleccione el canal que va a ver en la caja de
televisión por cable o en la caja de satélite.
BORRADO
(O AGREGACION) DE CANALES
TV
Los canales que ya no reciban más o que se vean
muy raramente podrán borrarse de la memoria. (Por
supuesto, podrá volver a agregar en la memoria los
canales que haya borrado de la misma.)
SELECCIÓN DE IDIOMA
1 Seleccione “AJUSTE DE CANAL”
Pulse SETUP en el mando a distancia. Pulse K o L
para apuntar a "AJUSTE DE CANAL".
Luego, pulse ENTER.
TV
1 Preparacion de canales por primera vez
Enchufe el cable de alimentación del televisor/DVD
en una toma de CA.
NOTA:
2 Seleccion “AGREGAR/BORRAR”
Pulse K o L para apuntar a "AGREGAR/BORRAR".
Luego, pulse ENTER.
Si aparecen algunos dígitos en la esquina de la
pantalla, pulse POWER sin desenchufar el cable de la
alimentación.
3 Introduzca el número del canal deseado
Pulse K o L hasta que aparezca el número del canal
deseado. (Podrá utilizar también los botones de
números o CH. K/L para introducirlos.)
(Ejemplo: CH8)
2 Encienda el televisor/DVD
Pulse POWER para encender el televisor/DVD.
3 Seleccione el idioma de la pantalla
Pulse K o L para apuntar a "LANGUAGE".
Luego, pulse ENTER para seleccionar "ENGLISH" o
"ESP" = Spanish o "FRA" = French. "[ ]" indica el
idioma seleccionado.
4 Bórrelo de la memoria o agréguelo a ella
Pulse ENTER. Los números de los canales se
encienden en rojo. El canal se borra de la memoria.
Canal agregado: Azul claro
Canal borrado: Rojo claro
4 Inicie el preajuste automático
Pulse K o L para apuntar a
"AUTOPRESELECCION". Luego, pulse ENTER. El
sintonizador explora y memoriza todos los canales
activos de su zona.
¡Para borrar otro canal, repita los pasos [3] y [4].
¡Si pulsa de nuevo ENTER, el canal se memorizará
de nuevo.
NOTAS:
• El televisor/DVD distingue entre los canales de TV
estándar y los canales de televisión por cable
(CATV).
5 Salga del modo de preparación de
canales
• El televisor/DVD puede memorizar canales de TV
como canales de CATV si las condiciones de la
recepción no son buenas. Si pasa esto, vuelve a
intentar la acción AUTOPRESELECCION cuando
las condiciones de la recepción sean mejores.
Pulse SETUP en el mando a distancia para volver al
modo del televisor.
NOTA:
Para confirmar que los canales hayan sido borrado o
agregados, pulse CHANNEL(CH.) K o L.
ES
–
–
37
0C28
DVD SECTION
REPRODUCCIÓN DE UN
DVD DE VÍDEO O UN CD
DE AUDIO
REPRODUCCION BASICA
DVD-V
CD
Para empezar
¡Conecte el interruptor del amplificador y otros
equipos, si fuera necesario.
1 Pulse el boton POWER.
¡La alimentación se conectará.
2 Pulse el botón OPEN/CLOSE.
¡La bandeja de carga del disco se abrirá.
3 Ponga el dlsco en la bandeja con el lado
de la eliguta hacia arriba.
4 Pulse el botón PLAY.
¡La bandeja se cerrará automáticamente y la
reproducción empezará luego desde el primer
capítulo o pista del disco. Si la reproducción no
empieza automáticamente, pulse PLAY.
¡Cuando reproduzca un DVD que tenga grabado un
menú de títulos, el menú aparecerá en la pantalla.
5
Pulse el botón STOP para detener la
reproducción.
ES
–
–
38
0C28
MEMO
ES
–
–
39
0C28
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to
any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI
AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,
please call 1-800-968-3429 or write to the following:
FUNAI CORPORATION, INC.
Customer Service
100 North Street; Teterboro, NJ 07608
Tel :1-800-968-3429
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia
0EMN02108
TD001UB #####
|