Sylvania TV VCR Combo 6309CC User Manual

OWNER’S

MANUAL

9-INCH COLOR TV/VCR

6309CC

This Owner’s Manual is made of

recycled paper.

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

energy efficiency. ENERGY STAR^®is

a U.S. registered mark.

If you need additional assistance for set-up or operating

after reading owner’s manual, please call

TOLL FREE : 1-800-968-3429.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/VCR, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

19.Damage Requiring Service-Unplug this TV/VCR from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/VCR.

c. If the TV/VCR has been exposed to rain or water.

d. If the TV/VCR does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/VCR to its normal operation.

14.Lightning-For added protection for this TV/VCR receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/VCR due to lightning and

power-line surges.

e. If the TV/VCR has been dropped or damaged in any way.

f. When the TV/VCR exhibits a distinct change in perfor-

mance-this indicates a need for service.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

21.Safety Check-Upon completion of any service or repairs to

this TV/VCR, ask the service technician to perform routine

safety checks to determine that the TV/VCR is in proper

operating condition.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/VCR through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/VCR.

22.Heat-This TV/VCR product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

18.Servicing-Do not attempt to service this TV/VCR yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to quali-

fied service personnel.

^{Download from Www.Somanuals.c}-^om3^.-^{All Manuals Search And Download.}

9J27

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

LOCATION

For safe operation and satisfactory performance of

your TV/VCR, keep the following in mind when

selecting a place for its installation:

Shield it from direct sunlight and keep it away

from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top and bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

Unauthorized recording or use of broadcast televi-

sion programming, video tape, film or other copy-

righted material may violate applicable copyright

laws. We assume no responsibility for the unautho-

rized duplication, use, or other acts which infringe

upon the rights of copyright owners.

•

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/VCR near strong magnetic fields.

Avoid moving TV/VCR to locations where temper-

•

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

ature differences are extreme.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

Do not put your fingers or objects into the

TV/VCR cassette holder.

Do not place anything directly on top of the unit.

•

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a tape is played in a TV/VCR

which has moisture, it may damage the tape and

TV/VCR. Therefore when the condensation occurs

inside the unit, turn the POWER button on and allow

at least 2 hours for the unit to dry out.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 4 -

9J27

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6

C OPERATING CONTROLS AND FUNCTIONS 7

C PREPARATION FOR USE . . . . . . . . . . . . . . . .9

C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .18

NORMAL RECORDING . . . . . . . . . . . . . . . . .19

SKIPPING UNWANTED SCENES DURING

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .19

OTR (One Touch Recording) . . . . . . . . . . . . . .19

TIMER RECORDING . . . . . . . . . . . . . . . . . . .20

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .22

AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .22

WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .22

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .23

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . . .11

CHANNEL SET UP FOR THE FIRST TIME . .11

CLOCK SET UP (AUTO / MANUAL) . . . . . .12

CHANNEL SET UP AGAIN . . . . . . . . . . . . . .13

DELETING (OR ADDING) CHANNEL . . . . .13

SELECTING THE LANGUAGE . . . . . . . . . . .14

DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .14

C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .23

C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .24

C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .24

REAL TIME TAPE COUNTER . . . . . . . . . . . .24

AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .24

C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .15

WATCHING A TV PROGRAM . . . . . . . . . . . .15

GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .15

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .24

C TROUBLESHOOTING GUIDE . . . . . . . . . . .25

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .26

C CABLE CHANNEL DESIGNATIONS . . . . . .26

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .16

NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .16

AUTO REPEAT PLAYBACK . . . . . . . . . . . . .16

SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .17

NOISE CANCEL (in the Still mode) . . . . . . . .18

VERTICAL HOLD CONTROL . . . . . . . . . . . .18

TRACKING ADJUSTMENT . . . . . . . . . . . . . .18

RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .18

INDICE

CONTROLES DE OPERACIÓN Y

MODO DE ENTRADA EXTERNA . . . . . . . . . . .30

SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .27

PREPARACIÓN DE CANALES POR

CONEXIONES DE ANTENA/CABLE . . . . . . . .29 PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31

INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .30 AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

^{Download from Www.Somanuals.c}-^om5^.-^{All Manuals Search And Download.}

9J27

FEATURES

Infrared remote control

Bilingual on screen menu display selectable in

English or Spanish

Still–“Freeze” the picture at any time, for close viewing

of a particular scene. Only tapes recorded in SLP mode

will show a fairly clear picture.

•

Digital Auto Tracking (DTR)–Automatically adjusts the

tracking for each tape you play.

Rental play mode–Improves playback picture quality

from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a tape

indefinitely without pressing the PLAY button.

Time search–Let you set the TV/VCR to advance the

tape by entering the desired playback time you want to

skip.

OTR (One Touch Recording)–Instant timed recording

from 30 to 480 minutes is possible at the push of the

REC/OTR button.

1 Year, 8 events (including Daily and Weekly Timer

Recording)–The built-in timer allows you to record up

to 8 programs at different times on different channels up

to 1 year in advance. The Daily timer allows recordings

to be made of daily broadcasts, and the Weekly timer

allows recording to be made once a week up to the end

of the tape.

Auto return–After timer recording is finished, the

TV/VCR can return to the beginning of the recording.

Wake up/Sleep timer–Allows you to have the TV/VCR

automatically turn on or off at a desired time.

Timer Program Extension–Allow you to shift the time

schedule for automatic timer recording.

Two- way power–Allows you to power the TV/VCR

with standard household AC or your vehicle’s battery,

using the supplied car-battery cord.

•

Real time counter–This shows the elapsed recording or

playback time in hours, minutes, and seconds. The “–”

indication will appear when the tape is rewound further

than the tape counter position “0:00:00”.

181 channel capability PLL frequency synthesizer

tuner with direct station call–(A converter may be nec-

essary to view scrambled cable channels.)

•

Auto Clock Setting–Allows you to set the clock function

from a PBS broadcast station.

•

Game mode–Automatically sets external input mode and

allows TV/VCR display to be suitable for use with TV

games.

Auto power on and off system–Automatically turns on

the TV/VCR when you insert the cassette, turns off after

auto-rewind, and ejects when the beginning of the tape is

reached.

•

Auto rewind when the end of a tape is reached–This

function doesn’t occur when using timer recording.

•

2 Step picture search operation–You can view a video

program at a high speed or super high speed in either a

forward or reverse direction in LP and SLP mode. For

SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

Auto Head Cleaner–Automatically cleans video heads as

you insert or remove a cassette.

Zero Return–The tape returns to counter of 0:00:00 by

rewinding or fast forwarding.

•

SUPPLIED ACCESSORIES

Remote Control Unit

Dipole Antenna

Matching Adapter

(300ohm-75ohm)

Car Battery Cord

WPZ0202GA004

(1813641 or 1780258 or

UCPGANTPK004)

AC Cord

2 AA Batteries

(0EMN00723 or

0EMN01183)

PART NO. (N0151UD)

WPV0182LW001/WPV0182HHH01

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-

968-3429.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control. If you decide to use a universal remote control with this unit, please be aware

that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-

versal remote control.

•

- 6 -

9J27

OPERATING CONTROLS AND FUNCTIONS

- TV/VCR FRONT PANEL -

POWER

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

VOLUME

CHANNEL

AUDIO VIDEO

EARPHONE

REC

1 2 3 4

5 6 7 8 9 10 11

12 13 14

5 POWER button– Press to turn TV/VCR on and off.

Press to activate timer recording.

6 STOP button– Press to stop the tape motion.

EJECT button– Press in the Stop mode to remove

tape from TV/VCR.

- REMOTE CONTROL -

WAKE-UP

/SLEEP

POWER

EJECT

L button–

CHANNEL

RETURN

Press to select setting modes from the on screen

menu.

•

Press to enter digits when setting program.

•

(for example: setting clock or timer program)

7 REW button– Press to rewind the tape, or to view

the picture rapidly in reverse during playback

mode. (Rewind Search)

CHANNEL

VOLUME

+100

DISPLAY

MUTE

s button–

Press to select a mode from a particular menu.

•

(for example: LANGUAGE or USER’S SET UP)

8 PLAY button– Press to begin playback.

K button–

PLAY

REW

F.FWD

STOP

Press to select setting modes from the on screen

menu.

•

SPEED PAUSE/STILL

RECORD

T-PROG.

CLEAR

GAME

TIME SEARCH

Press to enter digits when setting program.

•

(for example: setting clock or timer program)

9 F.FWD button– Press to rapidly advance the tape,

or to view the picture rapidly in forward during

playback mode. (Forward Search)

COUNTER

RESET

B button–

When setting program (for example: setting clock

•

1 AUDIO input jack– Connect to the audio output

jack of your audio equipment, video camera or

another VCR.

2 VIDEO input jack– Connect to the video output

jack of your video camera or another VCR.

3 RECORD indicator– Flashes during recording.

Lights up in the Stand-by mode for Timer

Recording.

or timer program), press to determine your selec-

tion and proceed to the next step you want to

input.

Press to determine setting modes from on screen

menu.

•

Press to select a mode from a particular menu.

(for example: LANGUAGE or USER’S SET UP)

•

4 Remote Sensor Window– Receives the infrared

signals from the remote control.

^{Download from Www.Somanuals.c}-^om7^.-^{All Manuals Search And Download.}

9J27

- REAR VIEW -

DC 13.2V

ANT

AC 120V

10 REC button– Press for manual recording.

OTR button– Activates One Touch Recording.

(only on the TV/VCR)

18 SPEED button– Press to choose the desired

recording speed:SP/SLP.

19 T-PROG. CLEAR button– Press to cancel a setting

of timer program. (See page 22.)

11 VOLUME X / Y buttons– Adjust the volume

level.

COUNTER RESET button– Press to reset counter

to 0:00:00.

20 GAME button– Sets the game mode and external

input mode at the same time. (See page 15.)

21 TIME SEARCH button– Press to activate Time

Search mode.

12 CHANNEL K / L buttons– Press to select the

desired channels for viewing or recording.

You may display the main menu on the TV screen

by pressing repeatedly this button on the

TV/VCR.

TRACKING function– Press to minimize video

‘noise’ (lines or dots on screen) during playback

mode. (See page 18.)

22 PAUSE/STILL button– Press to temporarily stop

the tape during the recording or to view a still pic-

ture during playback.

13 EARPHONE jack– Connects to earphones (not

supplied) for personal listening. The size of jack is

1/8” monaural (3.5mm).

23 MUTE button– Mutes the sound. Press it again to

resume sound.

24 CHANNEL RETURN button– Press to go back to

the previously viewed channel. For example,

pressing this button once will change channel dis-

play from 3 (present channel) to 10 (previously

viewed channel), and pressing it a second time

will return from 10 to 3.

25 WAKE-UP/SLEEP button– Sets the Wake up or

Sleep Timer. (See page 22 and 23.)

26 ANT. terminal– Connect to an antenna or cable

system.

14 Cassette compartment

15 Number buttons– Press to select desired channels

for viewing or recording. To select channels from

1 to 9, first press the 0 button and then 1 to 9.

+100 button– When selecting cable channels

which are higher than 99, press this button first,

then press the last two digits. (To select channel

125, first press the “+100” button then press “2”

and “5”.)

16 MENU button– Press to display the main menu on 27 DC 13.2V jack– Connect to the Car Battery Cord.

the TV screen.

28 AC 120V jack– Connect to the AC cord.

17 DISPLAY button– Display the counter or the cur-

rent channel number and current time on the TV

screen. (See page 24.)

- 8 -

9J27

PREPARATION FOR USE

From Cable System or

Satellite Dish

Dipole Antenna

(Supplied)

VHF/UHF Antenna

(Not supplied)

Satellite Box or

Cable Box

OUT

Flat twin-lead cable

(Not supplied)

VHF Antenna

(Not supplied)

UHF Antenna

(Not supplied)

From

Cable System

DC 13.2V

ANT

AC 120V

VHF/UHF

Combiner

(Not supplied)

ANT.

75-ohm

Coaxial Cable

(Not supplied)

Flat twin-lead cable

VHF/UHF COMBINED ANTENNA

A VHF UHF 75 ohm combination antenna can be

connected to ANT terminal.

ANTENNA/CABLE

CONNECTIONS

DIPOLE ANTENNA HOOK UP

VHF/UHF SEPARATE ANTENNAS

In some areas it will be necessary to use an outdoor

antenna.

1. Push the stem of the Dipole Antenna (accessory)

into the hole for antenna at the back of TV/VCR.

2. Connect the flat twin-lead cable from the Dipole

Antenna to the 300/75 ohm Matching Adapter

(accessory).

3. Plug the Matching Adapter to ANT terminal of

TV/VCR as shown in drawing.

For the best reception, extend the Dipole Antenna

and adjust its length and position. (Avoid handling

the top section when making adjustments.)

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your TV/VCR without a converter box.

By using this connection you can:

1) Use the TV/VCR remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

NOTE: This unit will ONLY record and view the

same channel.

NOTE: If it is difficult to get good reception with

the indoor antenna, the use of an outdoor antenna is

recommended. Before an outdoor antenna is connect-

ed to the set, the indoor antenna should be discon-

nected.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-

ed to the grounding system of the building as close to the point of cable entry as practical.

Antenna/Cable Connections Continued on the Next Page.

^{Download from Www.Somanuals.c}-^om9^.-^{All Manuals Search And Download.}

9J27

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown in drawing.

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/VCR Remote Control. Unattended timer record-

ing is limited to one channel at a time.

MOBILE CONNECTION

WARNING:The driver should never watch

the TV/VCR while operating a motor vehicle.

CAUTION: If you use the TV/VCR with the

vehicle’s engine off, recharge the vehicle’s

battery after about every 4 hours of use to

prevent it from running down. After you fin-

ish using the TV/VCR be sure you unplug the

car-battery cord from the cigarette-lighter

socket.

1) The supplied indoor antenna is adequate when

your vehicle is stationary. For best reception on

the road, use a high-quality VHF/UHF mobile TV

antenna.

2) Attach the car battery cord to the DC13.2V (12V)

connector on the back of the TV/VCR. Then, con-

nect the other end to your vehicle’s cigarette-

lighter socket.

TO RECORD A SCRAMBLED/UNSCRAMBLED

CHANNEL

1. Set the TV/VCR channel selector to the output

channel of the Cable Converter Box or Satellite

Box. (Ex. CH3)

2.Select the channel to record from your Cable

Converter Box or Satellite Box.

NOTES:

Be sure your vehicle has a 13.2-volt (12-volt), neg-

ative-ground electrical system.

•

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

Be sure you use only the supplied car battery cord.

Using another cord could damage the TV/VCR.

Be sure the socket is free of ashes and other debris.

Be sure to push the car battery cord’s plug com-

pletely into the cigarette-lighter socket.

Always unplug the car battery from the cigarette-

lighter socket before you unplug it from the

TV/VCR.

•

3)Replace the cover.

You must disconnect the car battery cord from the

TV/VCR before you can use the AC power.

•

Be sure to replace the fuse with only the same

type, 5A, 250V.

•

To the vehicle's

cigarette-lighter socket

VHF/UHF Combination

Mobile Antenna

(Not supplied)

EXTERNAL INPUT MODE

When using an external input signal (another VCR or

video camera), connect the player’s audio/video out-

put cables to the AUDIO IN/ VIDEO IN jacks of

Car battery cord

(Supplied)

your TV/VCR. Then press the CHANNEL K or

button until “AUX” appears on the screen.

DC13.2V

ANT.

DC13.2V

120V

AUX

- 10 -

9J27

SET UP FOR USE

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just

select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then

select the channel to be viewed on the Cable Box or Satellite Box.

CHANNEL SET UP FOR THE

TO SELECT A DESIRED CHANNEL

You can select the desired channel by using the

FIRST TIME

CHANNEL K or L button or directly pressing the

number buttons on the remote control.

Note for using the number buttons:

1 Plug in the TV/VCR power cord

Attach the smaller end of the sup-

plied AC cord to the AC 120V

When selecting cable channels which are higher

than 99, press the +100 button first, then, press the

last two digits. (Example: to select channel 125,

first press the +100 button then press “2” and “5”).

You must proceed single-digit channel numbers

with a zero (Example: 02 ... 09).

•

connector on the back of the

TV/VCR. Then, plug the other

end into a standard AC outlet.

NOTES:

AC 120V

•

You must disconnect the car battery cord from the

TV/VCR before you use AC power.

If some digits appear in the corner of the screen,

press the POWER button without unplugging the

power cord.

•

CLOCK SET UP

(AUTO / MANUAL)

2 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

Set the clock accurately for proper automatic timer

recording. If the Public Broadcasting Station (PBS)

is available in your area, follow “AUTO CLOCK

SETTING”. If it is not, follow “MANUAL CLOCK

SETTING”.

3 Select “ENGLISH” or “ESPAÑOL”

Select “ENGLISH” or

“ESPAÑOL”=Spanish using the

F.FWD/B or REW/s button. “[ ]”

indicate the selected language.

– SET UP –

LANGUAGE

[ENGLISH] ESPAÑOL

AUTO CLOCK SETTING

AUTO PRESET

You can have the TV/VCR set the clock automatical-

ly by using the Public Broadcasting Station (PBS)

channel in your area. Once you have set the clock by

using the following procedure, the TV/VCR will

automatically monitor the correct time and date

being broadcast by the PBS station in your area,

using a new service called Extended Data Service

(XDS).

4 Begin auto preset

– SET UP –

Press the PLAY/K or STOP/L but-

ton to point to “AUTO PRESET”.

Then press the F.FWD/B button.

The tuner scans and memorizes all

active channels in your area.

LANGUAGE

[ENGLISH] ESPAÑOL

AUTO PRESET

Make sure ...

NOTES:

TV/VCR power must be turned on.

Confirm that the antenna connections are correct.

The cable converter box must be turned on if your

TV/VCR is connected directly to it. (See NOTES:)

•

The TV/VCR distinguishes between standard TV

channels and cable channels.

•

If you want to play or record a video tape BEFORE

presetting the tuner, you must press the MENU but-

ton on the remote control. To preset the tuner again,

see “CHANNEL SET UP AGAIN” on page 13.

The TV/VCR may recognize TV channels to be

CATV channels by the receiving conditions. In this

case, try auto preset again in the fine receiving

conditions.

•

The channel is properly set in advance.

•

5 After scanning

The tuner stops on the lowest memorized channel.

If you want to recall the selected channels, you can

select the desired channel directly with the remote

control number buttons or CHANNEL K or L button.

- 11 -

9J27

NOTES:

If you choose [AUTO],

Auto clock setting only needs to be set once. But it

can be done again if the clock’s time has become

incorrect for some reason.

The TV/VCR must search until the PBS channel is

•

found. It must scan each channel for a couple of

seconds to determine if that channel is transmitting

the XDS signal.

If the TV/VCR is connected directly to a cable

•

converter box or satellite box, the local PBS station

must be selected on the cable box itself, and the

TV/VCR must be set to the output channel of the

cable converter box or satellite box (usually chan-

nel 3 or 4), to be able to set up or correct the clock

automatically.

If the time, that is automatically set by this select-

•

ed PBS station is incorrect, it may not be your

local PBS station, but one from a different time

zone. Or there is a case that no channel is broad-

casting the XDS signal in your area, as shown by

no time. In these cases, you must manually enter

the correct local PBS station, or set the clock man-

ually and turn off the Auto Clock Setting feature.

If you do not know what your local PBS station is,

then follow “Manual Clock Settings”.

The TV/VCR cannot control the channels of the

cable converter box or satellite box.

MANUAL CLOCK SETTING

Make sure ...

– M E N U –

1 Select “SETTING CLOCK”

TV/VCR power must be turned on.

In the example below, the clock is to be set to:

•

TIMER PROGRAMMING

PICTURE CONTROL

Press the MENU button on the

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

remote control.

DATE

May 1st, 2002

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

TIME SEARCH

SETTING TIME 5:40PM

Then, press the F.FWD/B button.

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

– SETTING CLOCK –

2 Set “AUTO CLOCK” to [ON]

Press the F.FWD/B or REW/s

button repeatedly until [ON]

appears.

AUTO CLOCK

[ON]

AUTO CLOCK CH

[AUTO]

[OFF]

MANUAL CLOCK SET

D.S.T.

Then, press the F.FWD/B button.

2 Select “MANUAL CLOCK SET”

Press the PLAY/K or STOP/L but-

ton to point to “MANUAL CLOCK

SET”.

3 Enter the channel number for the PBS station

– SETTING CLOCK –

Press the PLAY/K or STOP/L button to point to

AUTO CLOCK

[ON]

“AUTO CLOCK CH”.

– SETTING CLOCK –

AUTO CLOCK CH

[AUTO]

[OFF]

Then press the F.FWD/B or

AUTO CLOCK

[ON]

MANUAL CLOCK SET

D.S.T.

AUTO CLOCK CH

[AUTO]

Then, press the F.FWD/B button.

REW/s button until the channel

number for your local PBS station

appears.

MANUAL CLOCK SET

D.S.T.

[OFF]

If you do not know the PBS channel number, leave it

set to [AUTO] which is located before [2]. The

TV/VCR will search automatically all available chan-

nels for the local PBS station, and will select that

channel.

3 Select the month

– MANUAL CLOCK SET –

MONTH DAY YEAR

Press the PLAY/K or STOP/L but-

ton until your desired month

appears. (Example: May → 05)

Then, press the F.FWD/B button.

0 5

– – – – – – – – –

HOUR

– –

MINUTE

– – – –

4 Exit the Auto Clock Setting

Press the MENU button on the remote control to

return to TV mode.

4 Select the day

Press the PLAY/K or STOP/L but-

ton until your desired day appears.

(Example: 1st → 01)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

0 1 – – – – – – –

HOUR

– –

MINUTE

– – – –

5 Turn off the TV/VCR

Turn the TV/VCR off. Because the Auto Clock func-

tions automatically while the TV/VCR is off.

Then, press the F.FWD/B button.

- 12 -

9J27

5 Select the year

Press the PLAY/K or STOP/L but-

ton until your desired year appears.

(Example: 2002)

– MANUAL CLOCK SET –

MONTH DAY YEAR

CHANNEL SET UP AGAIN

0 5

0 1 WED 2 0 0 2

Make sure ...

Press the POWER button to turn on the TV/VCR.

HOUR

– –

MINUTE

– – – –

•

Then, press the F.FWD/B button.

1 Select “CHANNEL SET UP”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

6 Select the hour

– MANUAL CLOCK SET –

MONTH DAY YEAR

– M E N U –

Press the PLAY/K or STOP/L but-

ton until your desired hour appears.

(Example: 5, PM)

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

0 5

0 1 WED 2 0 0 2

HOUR

0 5

MINUTE

– – PM

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: 40)

2 Begin auto preset

0 5

0 1 WED 2 0 0 2

– CHANNEL SET UP –

HOUR

0 5

MINUTE

4 0 PM

Press the PLAY/K or STOP/L but-

ton to point to “AUTO PRESET”.

Then, press the F.FWD/B button.

The tuner scans and memorizes all

the active channels in your area.

ADD / DELETE CH (TV)

AUTO PRESET

8 Start the clock

Press the MENU button on the

remote control.

Although seconds are not displayed,

they begin counting from 00 when

you press the MENU button on the

5:40 PM

3 After scanning

The tuner stops on the lowest memorized channel.

remote control. Use this feature to synchronize the

clock with the correct time.

NOTE:

DELETING (OR ADDING)

CHANNEL

When unplugging the AC cord or if there is a power

failure for more than 3 seconds, you may have to

reset the clock.

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you

can add the deleted channel into the memory again.)

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps [1] and [2].

2)Select where you want to change using the

F.FWD/B or REW/s button.

3)Enter correct numbers using the PLAY/K or

STOP/L button.

– M E N U –

1 Select “CHANNEL SET UP”

TIMER PROGRAMMING

PICTURE CONTROL

Press the MENU button on the

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

remote control. Then press the

PLAY/K or STOP/L button to

point to “CHANNEL SET UP”.

Then, press the F.FWD/B button.

TIME SEARCH

4)Press the MENU button on the remote control to

start the clock.

2 Select “ADD/DELETE CH”

Press the PLAY/K or STOP/L but-

ton to point to “ADD/DELETE

CH”.

– CHANNEL SET UP –

ADD / DELETE CH (TV)

AUTO PRESET

PLEASE NOTE:

Press the F.FWD/B button.

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and press

the F.FWD/B or REW/s button to turn [OFF] this

function. Then you can manually adjust the clock.

3 Enter the desired channel number

Press the PLAY/K or STOP/L but-

ton until your desired channel num-

ber appears. (You can also use the

number buttons or the CHANNEL

K/L button to enter it.) (Example:

CH8)

ADD / DELETE

- 13 -

9J27

DAYLIGHT-SAVING TIME

Select this feature and the TV/VCR’s clock automati-

cally will advance one hour in April, then reverse one

hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

First Sunday of April : At 2 AM the clock imme-

4 Delete (or add) it from (into) memory

Press the F.FWD/B or REW/s button. The channel

number changes to light red. The channel is deleted

from memory.

To delete another channel, repeat steps [3] and [4].

If you press the F.FWD/B or REW/s button

again, the channel is memorized again.

•

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

Added channel: Light blue.

Deleted channel: Light red.

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

•

Make sure ...

5 Exit the channel setup mode

Press the POWER button to turn on the TV/VCR.

Press the MENU button on the remote control to

returns to TV mode.

•

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL K or L button.

1 Select “SETTING CLOCK”

Press the MENU button on the

– M E N U –

remote control.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

SELECTING THE LANGUAGE

TIME SEARCH

Make sure ...

Then, press the F.FWD/B button.

Press the POWER button to turn on the TV/VCR.

NOTE: This function effects only the language on

the screen menu and not the audio source.

•

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “D.S.T.”.

Then, press the F.FWD/B or

REW/s button until [ON] appears.

– SETTING CLOCK –

AUTO CLOCK

[ON]

1 Select “LANGUAGE”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

– M E N U –

AUTO CLOCK CH

[AUTO]

[ON]

TIMER PROGRAMMING

PICTURE CONTROL

MANUAL CLOCK SET

D.S.T.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

ton to point to “LANGUAGE”.

3 Exit the Daylight-Saving Time mode

Press the MENU button on the remote control to

return to TV mode.

2 Select “ENGLISH” or “ESPAÑOL”

Select “ENGLISH” or “ESPAÑOL”= Spanish using

the F.FWD/B or REW/s button.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], select [OFF] using the

F.FWD/B or REW/s button. Then, press the MENU

button to return to TV mode.

3 Exit the Language mode

Press the MENU button on the remote control to

return to TV mode.

NOTE: If for some reason the menu is in Spanish,

press the MENU button on the remote control, press

the PLAY/K button to point to “IDIOMA

[ESPAÑOL]”, then press the F.FWD/B button, then

press the MENU button on the remote control.

- 14 -

9J27

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

The TV/VCR’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a natural looking image.

NOTES:

1 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

2 Select the channel number

Press the CHANNEL K or L button to select your

desired channel number or press the number buttons

on the remote control.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be viewed must be selected

on the cable box or satellite box.

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

•

When setting the Picture Control, the Game mode

will be cancelled.

•

Make sure ...

TV/VCR power must be turned on.

•

1 Select “PICTURE CONTROL”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to ”PICTURE CON-

TROL”.

3 Adjust sound

Press the VOLUME or button

to adjust the volume.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

VOLUME 20

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

GAME MODE

2 Select item you want to adjust

Press the PLAY/K or STOP/L but-

ton until desired control is dis-

played.

This function enables you to decrease the TV screen

contrast and making it suitable for use with a TV

GAME.

NOTE: This function can not be set during recording.

BRIGHT

–

P +

CONTRAST

COLOR

TINT

GAME

Press the GAME button on the

remote control. “GAME” appears

on the screen.

SHARPNESS

When you press the GAME button;

3 Adjust the picture control

Press the F.FWD/B or REW/s button to adjust to

your desired level.

The TV/VCR comes on automatically if it is off.

The TV/VCR will be in external input mode auto-

matically.

•

REW/s

to decrease

brightness

to decrease

contrast

F.FWD/B

to increase

brightness

to increase

contrast

TO CANCEL THE GAME MODE

Press the GAME button or CHANNEL K or L but-

ton on the remote control.

BRIGHT

CONTRAST

DEGAUSSING

Magnetism from nearby appliances might affect the

color of the TV picture.

COLOR

TINT

to pale

to brilliant

to purple

to green

to clear

SHARPNESS to soft

If this happens, move this unit away from the appli-

ance. If the color is still not correct, disconnect

power cord from AC outlet then reconnect it after 30

minutes.

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

- 15 -

9J27

PLAYBACK

This TV/VCR will operate with any cassette that has the

recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

mark. For best results, we

INSERTING A CASSETTE

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the TV/VCR. The

AUTO REPEAT PLAYBACK

The TV/VCR has the auto repeat function that allows

you to repeat a tape indefinitely without touching the

PLAY button.

TV/VCR will automatically turn on.

ALL REPEAT: Repeat playback from the beginning

Window

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

WRONG

CORRECT

PRECAUTIONS

1 Select “USER’S SET UP”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

– M E N U –

Avoid moisture. Moisture condensation may occur

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/VCR, wait until the tape has warmed to

room temperature and the moisture has evaporated.

Avoid extreme heat, high humidity and magnetic

fields.

•

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

•

USER’S SET UP

2 Select “ALL” or “BLANK”

Press the PLAY/K or STOP/L but-

ton to point to “REPEAT PLAY”.

Press the F.FWD/B or REW/s

button repeatedly until your desired

–

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ALL]

[OFF]

NORMAL PLAYBACK

Make sure ...

selection [ALL] or [BLANK] appears.

TV/VCR power must be turned on.

•

3 Exit the Repeat Play setting

Press the MENU button on the remote control to

return to the TV mode.

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/VCR will start playback automatically.

4 Start playback

Press the PLAY button to start the Repeat Play.

”REPEAT PLAY B” appears.

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/VCR.

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

PLAY

2 To begin playback

Press the PLAY button.

Note: If any menu is activated on

the screen, the PLAY button does

not function. Press the MENU but-

ton to clear the menu. then, press

the PLAY button.

•

3 To stop playback

Press the STOP button when playback is completed.

TO CANCEL THE REPEAT PLAY MODE

STOP

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

- 16 -

9J27

NOTES:

Time Search can be set up to a maximum of 9

•

hours 50 minutes (9:50) by 10 minutes at a time.

PICTURE SEARCH

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

This function will not operate in recording mode.

•

In the example below: To watch a program after 2

hour 50 minutes from the present position, in either

direction.

1)You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD or REW button during playback. (in the

SP / LP / SLP modes)

2)Press it again and the TV/VCR will now search in

super high speed. (in the LP / SLP modes only)

NOTE: Tapes recorded in the SP or LP mode will

display a noise bar on the TV screen and the pic-

ture may revert to Black and White. This is normal.

3)Press the PLAY button to return to normal speed.

1 Insert a tape.

2 Select “TIME SEARCH” mode

Press the TIME SEARCH button (with each push it

will increase by 10 minute).

3 Enter your desired time

Press the PLAY/K or STOP/L but-

TIME SEARCH

2 : 50

ton until your desired time appears.

(Example: “2:50” stands for 2 hours

50 minutes)

If you wish to cancel the Time Search at this point,

press the MENU button on the remote control.

ZERO RETURN

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

NOTE:

4 Begin Time Search

By pressing the REW/s or F.FWD/B button, the

TV/VCR will rewind or fast forward to the specified

point.

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

2 Reset the counter to 0:00:00

Press the COUNTER RESET button repeatedly.

TO CANCEL THE TIME SEARCH at this

point

Press the STOP/EJECT button on the TV/VCR or the

remote control. This will delete the selected time.

3 Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback is

completed.

STILL PICTURE

You can view a still picture on the TV screen during

playback (the Still mode). Press the PAUSE/STILL

button during playback. Only tapes recorded in the

SLP mode will show the least amount of lines. Press

the PLAY button to return to playback.

NOTES:

4 To activate “ZERO RETURN” mode

Press the MENU button on the

– M E N U –

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “ZERO RETURN”.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

Usually there will be video “noise” lines (black

and white streaks or dots) on the screen. This is

normal.

•

Then, press the F.FWD/B button.

The counter will appear on the TV

screen.

The tape will automatically stop when the counter

returns to 0:00:00.

If the tape was originally recorded in SP or LP

mode, the still picture will be black and white in

addition to the “noise” lines.

This is not a fault of the machine, but is a by-

product of the technology involved in producing

a TV/VCR with 2 video heads.

If it is left in the Still mode for more than five min-

utes, the TV/VCR will automatically switch to the

Stop mode.

TIME SEARCH

The Time Search function makes it possible to

quickly advance the tape to your desired position

simply by entering the exact amount of playback

time you want to skip.

•

- 17 -

9J27

NOISE CANCEL (in the Still mode)

RENTAL PLAYBACK

This feature allows you to reposition or reduce the

noise lines of a still picture. Press the PAUSE/STILL

button so that the noise lines change position on the

screen so you can see the picture in its entirety with-

out distracting noise lines.

NOTE: This feature can be activated ONLY when

viewing a tape recorded in the SLP mode. If the tape

was originally recorded in the SP or LP mode, the

still picture may revert to black and white in addition

to the “noise bars”. This is normal.

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

– M E N U –

1 Select “USER’S SET UP”

TIMER PROGRAMMING

PICTURE CONTROL

Press the MENU button on the

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

TIME SEARCH

VERTICAL HOLD CONTROL

USER’S SET UP

–

2 Set “RENTAL” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “RENTAL”.

Press the F.FWD/B or REW/s

button until [ON] appears.

RENTAL

REPEAT PLAY

AUTO RETURN

[ON]

[OFF]

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

the CHANNEL K or L button.

NOTE:

If there are video noise lines on the screen, reposition

or reduce them. Refer to “NOISE CANCEL”.

3 Exit the Rental setting

Press the MENU button on the remote control to

return to the TV mode.

TRACKING ADJUSTMENT

4 Start playback

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

Press the PLAY button to start playback. “RENTAL

PLAY B” appears.

Once you select the Rental mode, it stays in effect

even after you turn off the TV/VCR.

•

However when playing pre-recorded tapes or tapes

•

recorded on units other than your own, noise lines

(black and white streaks) may appear on the play-

back picture. If this occurs, you can adjust the

tracking control manually by pressing the CHAN-

NEL K or L button until the streaks disappear. To

return to the DTR function, stop the tape once and

start playback again.

TO CANCEL THE RENTAL MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

RECORDING

TWO DIFFERENT TAPE SPEEDS

ERASE PREVENTION

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

Tape Speed

Type of tape

SP mode

Recording/Playback Time

If you decide to record on

the tape again, cover the

hole with plastic tape.

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

Note: You can playback a tape recorded in LP mode

(Long Play).

Plastic Tape

- 18 -

9J27

Make sure ...

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTE: This unit will ONLY record and view the same channel.

NORMAL RECORDING

OTR (One Touch Recording)

You can ONLY watch the same TV program that is

being recorded.

This function enables you to set a recording length

simply by pressing the REC/OTR button on the

TV/VCR.

Make sure ...

1 Select the channel to be recorded

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab

Press the number buttons on the

•

CH 10

remote control or the CHANNEL

K or L button.

in place. (If necessary, rewind or fast forward the

Remember: If the TV/VCR is con-

nected to a cable box or satellite

box, the TV/VCR must be on CH3

or CH4, then the channel to be recorded must be

selected on the cable box or satellite box.

tape to the point at which you want to begin

recording.)

NOTES:

This function CANNOT be done from the remote

control.

•

Recording starts immediately when the REC/OTR

button is pressed.

•

2 Select the tape speed

Press the SPEED button to select

the desired tape speed (SP/ SLP).

When the REC/OTR button is pressed 18 times, the

TV/VCR returns to the Normal Recording mode.

•

To stop the OTR operation, press the STOP button

on the TV/VCR or on the remote control.

•

To show the remaining time, press the DISPLAY

•

button on the remote control so that “OTR”

appears on the TV screen. (It will show up momen-

tarily then disappear.)

REC

3 Begin recording

Press the RECORD button.

Recording stops when 0:00 is reached.

Please note that in the SLP mode maximum record-

ing time, assuming the tape is started at the begin-

ning, is 8 hours using T-160 (or 6 hours using T-120).

•

4 Stop recording

Press the STOP button when recording is completed.

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, ejects the tape and turns itself off.

•

SKIPPING UNWANTED

1 Select the channel to be recorded

Press the number buttons on the remote control or the

CHANNEL K or L button.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

SCENES DURING RECORDING

Press the PAUSE/STILL button to

PAUSE

temporarily stop recording.

Press the PAUSE/STILL or

RECORD button to resume record-

ing.

NOTE:

After five minutes, the TV/VCR will automatically

switch to the Recording mode to prevent tape dam-

age.

•

2 Select the tape speed

Press the SPEED button to select the desired tape

speed (SP/ SLP).

- 19 -

9J27

Avoid over lap of programs ...

There is a chance that a program will not be record-

ed. when programs overlap;

3 Begin OTR

OTR(2 : 30)

Press the REC/OTR button on the

TV/VCR as many times as needed.

The recording length will be deter-

mined by the number of times you

press the REC/OTR button. Each

The program with an earlier start has priority.

Once the earliest program finishes, the overlapping

programs will begin recording in sequence.

•

The illustration below demonstrates the sequence

of recordings.

additional push will increase the recording time by

30 minutes. It is set up to 8 hours.

•

Recording Sequence

Push(es) Display

1 push

Recording length

(normal recording)

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

2 pushes

3 pushes

0:30

1:00

30 minutes

60 minutes

9:30AM-12:00PM

9:00AM

10:00AM

11:00AM

12:00PM

*Recording period is SHADED

17 pushes

8:00

480 minutes

1 Select “TIMER PROGRAMMING”

Press the MENU button on the remote control.

TIMER RECORDING

– M E N U –

Confirm “TIMER PROGRAM-

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

MING” is pointed by pressing the

PLAY/K button.

And press the F.FWD/B button.

You may set the TV/VCR to start and end a record-

ing while you are away. You can set 8 programs to

record on specific days, daily or weekly within a 1

year period.

In the example below, the timer is being set to record:

DATE:

If you have not yet set the clock,

•

“MANUAL CLOCK SET” appears. If so, follow

stops [3] to [8] on page 12. Then set the timer

recording.

July 6th, 2002

SETTING TIME: from 7:30PM to 8:50PM

CHANNEL:

TAPE SPEED:

CH61

2 Select your desired program position (1~8)

– TIMER PROGRAMMING –

Press the PLAY/K or STOP/L but-

ton to select the desired program

position.

Make sure ...

CH DATE

BEGIN END

- - -/- - - - - -:- -

-:- - - -

If a cable box or satellite box is connected with the

TV/VCR you will be limited to record only one

channel. And the channel selector on the TV/VCR

must be selected to the output channel of the boxes

CH 3 or CH 4 and then the actual channel to be

recorded must be selected on the boxes.

Clock must be set to the correct time and date

before setting the timer.

•

Then, press the F.FWD/B button.

3 Set the channel number

Press the PLAY/K or STOP/L but-

ton until the desired channel num-

ber appears.

(Example: CH61)

Then, press the F.FWD/B button.

•

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

TV/VCR power must be turn on to program it.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

•

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

The channel you want to record is properly set in

advance.

•

4 Select once, every day or weekly recording

For once recording :

– TIMER PROGRAMMING –

CH DATE

BEGIN END

Press the PLAY/K (up) button

until the desired date appears.

(Example: “7/06” for July 6th).

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 7/06 SAT -:- -

- - -/- - - - - -:- -

-:- - - -

- 20 -

9J27

For every day recording : To record a TV program at

the same time on the same channel every day.

(Example: Monday through Sunday)

10 Finish setting the program

Press the F.FWD/B or REW/s button. The program

is now completed.

Press the STOP/L (down) button

– TIMER PROGRAMMING –

CH DATE

BEGIN END

until “EVRY DAY” appears.

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

To set another program, repeat steps [2] to [10].

Press the MENU button on the remote control to

•

return to original mode.

For weekly recording : To record a TV program at

the same time on the same channel every week.

(Example: every Monday)

11 Set the timer

Press the POWER button to set automatic timer

recording. The TIMER REC indicator lights up.

– TIMER PROGRAMMING –

Press the STOP/L (down) button

You must turn off the TV/VCR to activate automat-

ic timer recording.

•

CH DATE

BEGIN END

until “EVRY” and your desired

day of the week appear together.

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

– TIMER PROGRAMMING –

CH DATE BEGIN END

5 Set beginning hour

To shift the time schedule of an automatic timer

recording.

1)Press the POWER button.

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “ 7, PM” for 7:30PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

61 7/06 SAT 7:12^P

- - -/- - - - - -:- -

2)Repeat step [1] on page 20.

3)Press the RECORD button and select the desired

program using the PLAY/K or STOP/L button.

4)Press the RECORD button again.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press the

PAUSE/STILL button on the remote control. The

recording time returns to the original time.

NOTE: When you shift forward the time schedule

during recording, the recording speed will automati-

cally be set to the SLP mode.

– TIMER PROGRAMMING –

CH DATE BEGIN END

6 Set beginning minute

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: “30” for 7:30PM)

- - -/- - - - - -:- -

-:- - - -

61 7/06 SAT 7:30^P

- - -/- - - - - -:- -

Then, press the F.FWD/B button.

7 Set end hour

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

8:30^PM - -

-:- - - -

61 7/06 SAT 7:30^P

- - -/- - - - - -:- -

5)Press the F.FWD/B or REW/s button to exit the

setting menu. Then press the MENU button on the

remote control to return to original mode.

8 Set end minute

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: “50” for

8:50PM)

- - -/- - - - - -:- -

-:- - - -

8:50^PM - -

-:- - - -

61 7/06 SAT 7:30^P

- - -/- - - - - -:- -

TO CORRECT A PROGRAM

While setting a program; press the REW/s but-

ton to go back one step and enter the correct num-

•

Then, press the F.FWD/B button.

bers using the PLAY/K or STOP/L button.

After setting a program;

1)Press the POWER button.

•

9 Set the tape speed

Press the PLAY/K or STOP/L but-

ton until the desired tape speed

appears. (Example: SP)

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

8:50^PMSP

-:- - - -

2)Repeat steps [1] - [2] on page 20.

3)Press the F.FWD/B button (or press the REW/s

button to go back one step) until the part you

want to correct begins flashing, then make the

changes pressing the PLAY/K or STOP/L but-

ton.

61 7/06 SAT 7:30^P

- - -/- - - - - -:- -

4)Press the POWER button to set automatic timer

recording.

- 21 -

9J27

USER’S SET UP

–

2 Set “AUTO RETURN” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “AUTO RETURN”.

Press the F.FWD/B or REW/s

button until [ON] appears. Then,

TO CANCEL AN AUTOMATIC TIMER

RECORDING

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ON]

After setting a program;

1)Press the POWER button.

•

2)Repeat steps [1] ~ [2] on page 20 and select a

program you want to cancel.

press the MENU button on the remote control to

return to TV mode.

3)Press the T-PROG. CLEAR button.

4)Press the MENU button on the remote control to

return to TV mode.

While recording is in progress;

1)Press POWER button.

3 Auto Return will begin

When all the timer recordings are completed, the

•

TV/VCR will rewind to the beginning of the recorded

program(s).

NOTE:

2)Press the STOP/EJECT button on the TV/VCR.

If you press the POWER button while tape is

rewinding, the Auto Return will stop.

•

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the REC indicator

goes off.

2)Press the MENU button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed.

4)Press the F.FWD/B button. The details of pro-

grams appear on the TV screen.

5)Press the MENU button on the remote control to

return to TV mode.

4 Watch the recorded program

Press the PLAY button.

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button.Then, press the MENU

button on the remote control to return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

HINTS FOR AUTOMATIC

TIMER RECORDING

Make sure the channel you want to record is prop-

erly set in advance.

•

It is not necessary to press the RECORD button for

timer recording.

•

WAKE UP TIMER

Recording begins automatically at the Start time.

If you are recording using a Timer mode, you may

not operate the unit manually.

•

The Wake Up Timer function turns on the TV/VCR

without using the POWER button after a desired

period of time.

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

If the erase-prevention tab is removed, the cassette

will be ejected when the POWER button is pressed

to off.

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, and the tape will be ejected.

NOTES:

•

Use the remote control for this procedure.

Clock must be set to the correct time before setting

the timer.

•

If you want to select [TAPE], you must insert a

cassette tape in the TV/VCR. The tape will start

playback automatically on your desired time.

•

1 Select “WAKE UP TIMER”

Press the WAKE-UP/SLEEP button

on the remote control once, and

confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s

button until [ON] appears.

AUTO RETURN

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

WAKE UP B ON/OFF

[ON]

TIMER

TV/TAPE

TIME

[TV]

[12:00AM]

1 Select “USER’S SET UP”

– M E N U –

2 Select “TV” or “TAPE”

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

Press the PLAY/K or STOP/L but-

ton until to point to “TV/TAPE”.

Press the F.FWD/B or REW/s

button, and select [TV] or [TAPE].

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

TIME SEARCH

WAKE UP

TIMER

ON/OFF

B TV/TAPE

TIME

[ON]

[TV]

[12:00AM]

- 22 -

9J27

SLEEP TIMER

The Sleep Timer function turns off the TV/VCR

without using the POWER button after a desired

period of time.

3 Set wake up time

Press the PLAY/K or STOP/L but-

ton until to point to “TIME”.

Press the F.FWD/B or REW/s

button until your desired wake up

time appears.

WAKE UP

TIMER

ON/OFF

[ON]

TV/TAPE

[TV]

NOTE:

B TIME

[12:00AM]

This function does not operate during Recording

•

mode.

Each additional push will increase (or decrease) the

time by 10 minutes.

1 Select “SLEEP TIMER”

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

4 Exit the Wake Up Timer setting

Press the MENU button on the remote control to

return to TV mode.

2 Set sleep time

Press the PLAY/K, STOP/L,

F.FWD/B or REW/s button until

your desired sleep time appears.

TO CANCEL THE WAKE UP TIMER

Press the WAKE-UP/SLEEP button on the remote

control once, and confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s button until [OFF]

appears.

SLEEP TIMER [2:00]

Each additional push will increase

the time by 30 minutes up to 120 minutes.

Press the MENU button on the remote control to exit

the Sleep Timer setting.

TO CANCEL THE SLEEP TIMER

Press the WAKE-UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

To view the time left for sleep timer, press the

WAKE-UP/SLEEP button twice, then press the

MENU button on the remote control to exit the sleep

timer setting.

COPYING A VIDEO TAPE

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

You can make copies of video tapes made by friends

or relatives for your enjoyment.

2)Insert a blank video cassette, or one you want to

record over, into the TV/VCR’s cassette compart-

ment.

3)Press the SPEED button on remote control for the

TV/VCR to select the desired recording speed

(SP/SLP).

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

Connect your TV/VCR and a Source (Playing) VCR

using the following diagram.

4)Press the CHANNEL K or L button on the

TV/VCR until “AUX” appears on the screen.

NOTE: “AUX” is found below the lowest memo-

rized channel. (Example: CH2)

5)Press the RECORD button on the TV/VCR.

6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

NOTE: For best results during dubbing, use the

TV/VCR’s front panel controls whenever possible.

The remote control might affect the source (Playing)

VCR’s playback operation.

POWER

AUDIO VIDEO

REC

[The TV/VCR]

[Ex: Source (playing)

VCR or camcorder]

VIDEO

Audio/Video

adapter cable

(not supplied)

OUT

AUDIO

- 23 -

9J27

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

Counter mode: After 5 seconds, only

the counter remains. To clear it, press

the DISPLAY button.

Clock mode: After 5 seconds, only

the clock and the channel number

remain. To clear them, press the DIS-

PLAY button.

•

5:40PM

CH2

Press

once

Press

once

COUNT 0:12:34

Press once

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time

will not change on a blank tape or blank portions on

the tape.)The “–” indication will appear when the

tape has rewound further than “0:00:00” on the tape

counter.

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/VCR will eject the tape and turn

itself to off.

This function is operative when Repeat Play is set

to the [OFF] position.

•

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

MAINTENANCE

1.Please visit your local Audio/Video store and pur-

CABINET CLEANING

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-968-3429, to

locate an Authorized Service Center.

NOTES:

Wipe the front panel and other exterior surfaces of

the TV/VCR with a soft cloth immersed in luke-

warm water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the TV/VCR. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

Remember to read the instructions included with

the video head cleaner before use.

•

Clean video heads only when problems occur.

•

AUTO HEAD CLEANING

SERVICING

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

Should your TV/VCR become inoperative, do not

•

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

968-3429, to locate an Authorized Service Center.

Playback picture may become blurred of interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use, or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

back, the video heads in your TV/VCR may need

to be cleaned.

- 24 -

9J27

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,

locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to

remedy the problem.

PROBLEM

CORRECTIVE ACTION

No power.

Make sure the AC cord is connected to an AC outlet.

Make sure the car battery cord is connected to vehicle’s cigarette

lighter socket and to DC 13.2V (12V) jack on back of the TV/VCR.

Check the fuse (5A, 250V) in car battery cord.

•

Make sure the power is turned on.

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Let the TV/VCR program its’ tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the TV/VCR clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

No picture and sound.

No picture or poor picture on

TV/VCR.

No sound or poor sound.

Timer recording is not possible.

Cannot go into Record mode.

Playback picture is partially noisy.

Adjust tracking control for a better picture using the CHANNEL

or L button on the TV/VCR.

Head cleaning may be necessary. Refer to “AUTO HEAD

CLEANING” on page 24.

No picture but the audio is OK in

playback.

No operation by infrared Remote

Control.

Video or color fades in and out

when making a copy of a video tape

Can not set the auto clock to ON.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

copy guard protection.

•

Make sure the AC cord is connected to an AC outlet.

- 25 -

9J27

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

CRT :

9 inch in-line gun, 90˚

deflection tube

NTSC-M

Rotary two-head

1/2 inch

Video input level :

Audio input level :

0.5~2.0Vp-p

-15dBs

Television system :

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

Video S/N ratio : More than 46dB

Audio S/N ratio : More than 43dB

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

OTHER SPECIFICATIONS

Power requirement : AC 120V/60Hz

DC 13.2V (12V)

Power consumption : AC 55W / DC 60W

Dimensions :

#2~#6

#7~#13

#14~#69

H:13” (330mm)

W:12-1/8” (308mm)

D:12-15/16” (329mm)

18.5 lbs (8.4kg)

CATV

VHF :

Weight :

MID band :

SUPER band :

HYPER band :

Terminals

A5~A1, A~I

J~W

W+1~W+84

Designs and specifications are subject to change

without notice and without our legal obligation.

If there is a discrepancy between languages, the

default language will be English.

•

Antenna input :

VHF/UHF 75 ohms

unbalanced

Video input :

Audio input :

Earphone :

RCA connector [ 1

1/8” monaural (3.5 mm)

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

106 107 108 109 110 111 112 113 114 115 116 117 118 119 120

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

TV Display

CATV channel

TV Display

- 26 -

9J27

CONTROLES DE OPERACIÓN Y SUS FUNCIONES

NOTA:

No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un

mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el

número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del

mando a distancia universal.

- PANEL DELANTERO -

POWER

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

VOLUME

CHANNEL

AUDIO VIDEO

EARPHONE

REC

1 2 3 4

6 7 8 9 10 11

12 13 14

5 Botón de la alimentación (POWER)– Púlselo para encender y

apagar el televisor/videograbadora. Púlselo para activar la

grabación con temporizador.

- CONTROL REMOTO -

6 Botón de parada (STOP)– Púlselo para detener la cinta.

Botón de expulsión (EJECT)–Púlselo en el modo de parada

para expulsar la cinta del televisor/videograbadora.

Botón L–

WAKE-UP

POWER

/SLEEP

EJECT

Púlselo para seleccionar los modos de ajuste en el menú de la

•

pantalla.

CHANNEL

RETURN

Púlselo para introducir dígitos cuando establezca un progra-

ma.

(Por ejemplo: Para ajustar el reloj o establecer un programa de

temporizador)

7 Botón de rebobinado (REW)– Púlselo para rebobinar la cinta,

o para ver la imagen en retroceso rápido durante el modo de

reproducción. (Búsqueda con rebobinado)

Botón s–

CHANNEL

VOLUME

+100

DISPLAY

MUTE

Púlselo para seleccionar un modo desde un menúparticular.

•

(Por ejemplo: IDIOMA o ADJUST DE USER)

8 Botón de reproducción (PLAY)– Púlselo para iniciar la repro-

ducción.

Botón K–

PLAY

REW

F.FWD

Púlselo para seleccionar los modos de ajuste en el menú de la

pantalla.

STOP

•

SPEED PAUSE/STILL

RECORD

Púlselo para introducir dígitos cuando establezca un programa.

(Por ejemplo: Para ajustar el reloj o establecer un programa de

T-PROG.

CLEAR

GAME

TIME SEARCH

temporizador)

9 Botón de avance rápido (F.FWD)– Púlselo para avanzar rápi-

damente la cinta, o para ver la imagen en avance rápido

durante el modo de reproducción. (Búsqueda con avance rápi-

do)

Botón B–

COUNTER

RESET

Cuando establezca un programa (por ejemplo: para ajustar el

•

reloj o para establecer un programa de temporizador), púlselo

para determinar su elección y vaya al paso siguiente que

quiera introducir.

1 Toma de entrada de audio (AUDIO)– Conéctela a la toma de

salida de audio de su equipo de audio, videocámara u otra

videograbadora.

2 Toma de entrada de vídeo (VIDEO)– Conéctela a la toma de

salida de vídeo de su videocámara u otra videograbadora.

3 Indicador de grabación (RECORD)– Parpadea durante la

grabación.

Se enciende en el modo de espera de la grabación con tempo-

rizador.

4 Ventanilla sensora del mando a distancia– Recibe las señales

Púlselo para determinar los modos de ajuste en el menú de la

•

pantalla.

Púlselo para seleccionar un modo desde un menúparticular.

(Por ejemplo: IDIOMA o ADJUST DE USER)

10 Botón de grabación (REC)– Púlselo para iniciar la grabación

manual.

Botón de grabación de un toque (OTR)– Activa la grabación

de un toque. (Sólo en el televisor/videograbadora)

infrarrojas procedentes del mando a distancia.

- 27 -

0M14

- PANEL TRASERO -

DC 13.2V

ANT

AC 120V

11 Botones de volumen (VOLUME X / Y)– Ajustan el nivel del

volumen.

18 Botón de velocidad de cinta (SPEED)– Púlselo para elegir la

velocidad de grabación deseada: SP/SLP.

12 Botones de canales (CHANNEL K/ L)– Púlselos para selec-

cionar los canales deseados para ver o grabar.

Se puede mostrar el menú principal en la pantalla del televisor

pulsando repetidamente este botón del televisor/videograbadora.

Función de seguimiento– Pulse los botones para minimizar el

ruido de vídeo (líneas o puntos en la pantalla) durante la

reproducción.

13 Toma de auriculares (EARPHONE)– Para conectar los auricu-

lares (no suministrados) y escuchar en privado. La toma es

mono y tiene un tamaño de 3,5 mm.

19 Botón T-PROG. CLEAR– Púlselo para cancelar un programa de

temporizador.

Botón de reposición del contador (COUNTER RESET)–

Púlselo para reponer el contador a 0:00:00.

20 Botón de juego (GAME)– Establece el modo del juego y el

modo de entrada externa al mismo tiempo.

21 Botón de búsqueda con tiempo (TIME SEARCH)– Púlselo

para activar el modo de búsqueda con tiempo.

22 Botón de pausa/imagen fija (PAUSE/STILL)– Púlselo para

detener temporalmente la cinta durante la grabación o para ver

una imagen fija durante la reproducción.

14 Compartimiento del videocasete

15 Botones numerados– Púlselos para seleccionar los canales

deseados para ver o grabar. Para seleccionar canales del 1 al 9,

pulse primero el botón 0 y luego el botón 1 a 9.

Botón +100– Cuando seleccione canales de televisión por

cable cuyo número sea superior al 99, pulse primero este

botón, y luego pulse los dos últimos dígitos. (Para seleccionar

el canal 125, pulse primero el botón “+100” y luego el “2” y

el “5”.)

23 Botón de silenciamiento (MUTE)– Silencia el sonido. Púlselo

de nuevo para recuperar el sonido.

24 Botón de retorno de canal (CHANNEL RETURN)– Púlselo

para volver al canal anterior. Por ejemplo, pulsando una vez

este botón, la visualización del canal cambiará de 3 (canal

actual) a 10 (canal anterior), y al pulsarlo por segunda vez, el

canal cambiará del 10 al 3.

25 Botón del temporizador despertador/para dormir (WAKE

UP/SLEEP)– Ajusta el temporizador para despertarse/dormir.

26 Terminal de antena (ANT.)– Para conectar una antena o sis-

tema de televisión por cable.

27 DC 13.2V– Conecta el cordón para la batería del automóvil.

28 AC 120V– Conecta el cordón de CA.

16 Botón de menú (MENU)– Púlselo para visualizar el menúprin-

cipal en la pantalla del televisor.

17 Botón del visualizador (DISPLAY)– Visualiza el contador o el

número del canal actual y la hora actual en la pantalla del tele-

visor.

- 28 -

0M14

CONEXIONES DE ANTENA/CABLE

Desde el cable coaxial

o caja de emisiones vía

satélite de 75 ohm del

sistema de Cable

Antena combinada de

VHF/UHF

(no incluído)

Antena Dipolar

OUT

Caja de CATV

o caja de emi-

siones vía satélite

(no incluído)

Antena VHF

(no incluído)

Desde el

sistema de Cable

Antena UHF

(no incluído)

DC 13.2V

ANT

AC 120V

Combinador de

VHF/UHF

(no incluído)

ANT.

Cable coaxial

de 75 ohm (no

incluído)

CONEXION DE LA ANTENA BIPOLAR

1. Introduzca la varilla de la antena bipolar (accesorio) en el orifi-

cio destinado para la antena, en la parte trasera de la TV/VCR.

2. Conecte el cable bifilar plano de la antena bipolar al adaptador

de acoplo (accesorio) de 300/75 ohm.

3. Enchufe el adaptador de acoplo al terminal ANT de la TV/VCR,

como lo muestra el dibujo.

CABLE CON CONVERTIDOR/DESCODI-

FICADOR O CONVERTIDOR DE EMI-

SIONES VÍA SATÉLITE

Si su servicio de televisión por cable le suministra un convertidor,

o si usted utiliza un sistema de emisiones vía satélite, usted podrá

utilizar las conexiones básicas.

Utilizando estas conexiones, usted también podrá grabar canales

codificados. Sin embargo, la selección de los canales deberá hac-

erse con el convertidor de televisión por cable con el convertidor

de emisiones vía satélite. Esto significa que los canales no podrán

ser cambiados con el mando a distancia del televisor/videograbado-

ra. La grabación inatendida se limita a un canal cada vez.

PARA GRABAR UN CANAL CODIFICADO/DESCODIFI-

CADO

1. Ajuste el selector de canales del televisor/videograbadora al

canal de salida del convertidor de televisión por cable o del con-

vertidor de emisiones vía satélite. (Ej.: CA3)

Para obtener una mejor recepción, extienda la antena de varilla y

regule su longitud y posición. (Evite tocar su parte superior mien-

tras hace los ajustes.)

NOTAS: Si es difícil obtener una buena recepción con la antena

de interiores, se recomienda usar una antena de exteriores. Antes

de instalar una antena de exteriores al aparato, se debe desconectar

la antena de interiores.

ANTENA COMBINADA DE VHF/UHF

Una antena de combinación de 75 ohm para VHF/UHF puede ser

conectada al terminal ANT.

2. Seleccione el canal que desee grabar de su convertidor de tele-

visión por cable o del convertidor de emisiones vía satélite.

ANTENAS SEPARADAS DE VHF/UHF

En algunos lugares será necesario utilizar una antena exterior.

CABLE SIN CONVERTIDOR/DESCODIFI-

CADOR

Utilice esta conexión si su sistema de televisión por cable se

conecta directamente a su televisor/videograbadora sin conver-

tidor.Utilizando esta conexión usted podrá:

1) Utilizar el mando a distancia del televisor/videograbadora para

seleccionar canales.

2) Programar uno o más canales sin codificar para realizar la

grabación automática con temporizador.

NOTA: Con esta unidad SÓLO se podrá grabar y ver un mismo

canal al mismo tiempo.

Aviso a los instaladores de sistemas CATV:

Este aviso se incluye para que los instaladores de sistemas

CATV tenga en cuenta el Artículo 820-40 del NEC, que propor-

ciona consejos para hacer una conexión apropiada a tierra y, en

particular, especifica que el cable de tierra deberá conectarse a

un sistema de puesta a tierra del edificio tan cerca del punto de

entrada del cable como sea posible.

- 29 -

0M14

CONEXION MOVIL

INSTALACIÓN DE LAS PILAS

1)Abra la tapa del compartimiento de las pilas del mando

a distancia presionándola en el sentido de la flecha.

2)Inserte 2 pilas tamaño “AA” en el compartimiento de las

pilas, en el sentido indicado por las marcas de polaridad

(+/-).

ADVERTENCIA: El conductor nunca debe ver programas

del televisor o del videobgrabadora mientras está con-

duciendo un vehículo.

PRECAUCIÓN: Si usted usa la TV/VCR con el motor del

vehículo apagado, recargue la batería del vehículo aprox.

cada 4 horas de uso, para evitar que ésta se agote. Cuando

termine de usar la TV/VCR, siempre desenchufe el cordón

para la batería del automóvil del zócalo del encendedor de

cigarrillos.

3)Vuelva a poner la tapa.

1) La antena de interiores incluída es adecuada para usar cuando el

vehículo está inmóvil. Para obtener una mejor recepción en ruta,

utilice una antena de VHF/UHF para TV móvil de alta calldad.

2) Enchufe el cordón para batería de automóvil al conector DC13.2V

(12V) en la parte posterior de la TV/VCR. Luego conecte el otro

extremo en el zócaio para el encendedor de cigarrillos del

automóvil.

NOTAS:

Confirme que su vehículo tlene un sistema eléctrico a tierra neg-

ativo de 13.2 (12) voltios.

•

MODO DE ENTRADA EXTERNA

Cuando utilice una señal de entrada externa (otra

videograbadora o una videocámara), conecte los cables de

salida de audio/vídeo del equipo de reproducción a las

tomas AUDIO IN/VIDEO IN de su

televisor/videograbadora. Y luego pulse el botón CHAN-

NEL K o L hasta que “AUX” aparezca en la pantalla.

Confirme que está usando sólo el cordón provisto para la batería

•

del automóvil. El uso de otro cordón puede dañar su TV/VCR.

Asegúrese que no haya cenizas ni otro restos en el zócalo del

encendedor.

Asegúrese de introducir completamente el enchufe del cordón de

la batería del automóvil en el zócalo del encendedor de cigarrillos.

Siempre desenchufe primero del zócalo del encendedor de cigar-

rillos el cordón para la batería del coche, antes de desconectarlo

de la TV/VCR.

Usted puede programar el temporizador para que explore

todos los canales que puedan recibirse en su zona.

Antes de usar la alimentación de CA, usted debe desconectar de

la TV/VCR el cordón para la batería del atuomóvil.

•

Solamente reemplace un fusible por otro del mismo tipo 5A,

250V.

•

Al zócalo del encendedor

de cigarrillos el cordón

para la batería del coche

Antena de VHF/UHF

para TV móvil

(no incluído)

Cordón para la batería

del automóvil

DC13.2V

ANT.

DC13.2V

120V

- 30 -

0M14

PREPARACIÓN DE CANALES POR

PRIMERA VEZ

AJUSTE DEL RELOJ

Cerciórese...

1) Conecte el extremo más pequeño del cordón de CA al conector

de CA de 120V en la parte posterior de la TV/VCR. Luego,

enchufe el otro extremo en un tomacorriente normal de CA.

La alimentación del televisor/videograbadora deberá

•

estar conectada.

En el ejemplo de abajo, el reloj va a ajustarse así:

FECHA: 1 de mayo de 2002

HORA: 5:40 PM

1) Pulse el botón MENU en el mando a distancia.

Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE RELOJ”.

Luego, pulse el botón F.FWD/B.

2) Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE MANUAL RELOJ”.

Luego, pulse el botón F.FWD/B.

3) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el mes deseado. (Ejemplo: Mayo - 05)

NOTAS:

Dede desconectar de la TV/VCR el cordón para la batería del

automóvil antes de usar la alimentación de CA.

•

Si aparezcan algunos digitos en el rincón de la pantalla, pulse el

botón POWER sin desenchufar el cable de alimentación.

•

2) Pulse el botón POWER para encender el

televisor/videograbadora.

3) Seleccione “ENGLISH” o “ESPAÑOL” utilizando el botón

F.FWD/B o REW/s. “[ ]” indica el idioma seleccionado.

4) Pulse el botón PLAY/K o STOP/L para señalar “AUTOPRESE-

LECCION”.

Luego pulse el botón F.FWD/B. El sintonizador explorará y

memorizará todos los canales activos de su área.

NOTAS:

Luego, pulse el botón F.FWD/B.

El televisor/videograbadora distingue entre los canales de tele-

•

4) Pulse el botón PLAY/K o STOP/L hasta que aparezca

visión estándar y los canales de televisor por cable.

el día del mes deseado. (Ejemplo: 1 - 01)

Si desea reproducir o grabar una cinta ANTES de preajustar el

sintonizador, usted tendrá que pulsar el botón MENU en el

mando a distancia.

Luego, pulse el botón F.FWD/B.

5) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el año deseado. (Ejemplo: 2002)

Luego, pulse el botón F.FWD/B.

6) Pulse el botón PLAY/K o STOP/L hasta que aparezca

la hora deseada. (Ejemplo: 5, PM)

Luego, pulse el botón F.FWD/B.

7) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el minuto deseado. (Ejemplo: 40)

La unidad de televisor/videograbadora puede reconocer los

•

canales de TV como ellos de TV por cable a causa de los condi-

ciones de recepción. En este caso, pruebe el preajuste automáti-

co de nuevo en los condiciones finas de recepción.

5) El sintonizador se para en el canal memorizado más bajo. Si

desea recuperar canales seleccionados, usted podrá seleccionar

directamente el canal deseado con los botones numerados del

mando a distancia o con los botones CHANNEL K o L.

8) Pulse el botón MENU en el mando a distancia. Aunque

los segundos no se visualizan, éstos empiezan a contar

desde 00 cuando se pulsa MENU en el mando a distan-

cia. Utilice esta función para sincronizar el reloj con la

hora correcta.

- 31 -

0M14

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials

or workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from

the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded

from this warranty.

LABOR:

FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date

of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail

purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty

does not apply to any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product

not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplica-

tion, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FIT-

NESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTA-

TIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED

SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHO-

RIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT

FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITH-

OUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,

please call 1-800-968-3429 or write to the following:

FUNAI CORPORATION

Customer Service

100 North Street; Teterboro, NJ 07608

Tel :1-800-968-3429

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Malaysia

0EMN01903

T4302UC * * * * *

Sharp All in One Printer AR 153E User Manual
Sony Camcorder TRV85 User Manual
Sony Projector VPL CX11 User Manual
Sony Stereo System ZS YN7L User Manual
Sony VCR GA45AV User Manual
Spectra Radio KT2042 User Manual
Star Manufacturing Cooktop 502D User Manual
Star Micronics Printer SJ 48 User Manual
Sterling Planer SSV 05 R User Manual
SunBriteTV TV Mount SBWM46 User Manual