Sylvania TV VCR Combo 6313CD User Manual

OWNER’S  
MANUAL  
COLOR TV/VCR  
6313CD (13 inch)  
6319CD (19 inch)  
19” MODEL ILLUSTRATED  
This Owner’s Manual is made of  
recycled paper.  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
As an ENERGY STAR®  
Partner, our company has  
determined that this product meets  
the ENERGY STAR® guidelines for  
If you need additional assistance for set-up or operating after  
reading owner’s manual, please call TOLL FREE : 1-800-968-3429.  
Or visit our WEB SITE at http://www.funai-corp.com  
energy efficiency. ENERGY STAR® is  
a U.S. registered mark.  
Please read before using this equipment  
 
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
13.Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the TV/VCR, be sure the  
antenna or cable system is grounded so as to provide some  
protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code,  
ANSI/NFPA No. 70, provides information with respect to  
proper grounding of the mast and supporting structure,  
grounding of the lead-in wire to an antenna discharge unit,  
size of grounding conductors, location of antenna-discharge  
unit, connection to grounding electrodes, and requirements  
for the grounding electrode. (Fig. A)  
19.Damage Requiring Service-Unplug this TV/VCR from  
the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the  
TV/VCR.  
c. If the TV/VCR has been exposed to rain or water.  
d. If the TV/VCR does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions, as improper adjust-  
ment of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the TV/VCR to its normal operation.  
14.Lightning-For added protection for this TV/VCR receiver  
during a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall  
outlet and disconnect the antenna or cable system. This will  
prevent damage to the TV/VCR due to lightning and  
power-line surges.  
e. If the TV/VCR has been dropped or damaged in any way.  
f. When the TV/VCR exhibits a distinct change in perfor-  
mance-this indicates a need for service.  
15.Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
20.Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
21.Safety Check-Upon completion of any service or repairs to  
this TV/VCR, ask the service technician to perform routine  
safety checks to determine that the TV/VCR is in proper  
operating condition.  
16.Overloading-Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this TV/VCR through openings as they may touch dan-  
gerous voltage points or short out parts that could result in  
a fire or electric shock. Never spill liquid of any kind on  
the TV/VCR.  
22.Heat-This TV/VCR product should be situated away from  
heat sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce heat.  
18.Servicing-Do not attempt to service this TV/VCR yourself  
as opening or removing covers may expose you to danger-  
ous voltage or other hazards. Refer all servicing to quali-  
fied service personnel.  
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT.  
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE  
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.  
- 3 -  
EN  
9I03  
 
PRECAUTIONS  
IMPORTANT COPYRIGHT INFORMATION  
LOCATION  
For safe operation and satisfactory performance of  
your TV/VCR, keep the following in mind when  
selecting a place for its installation:  
Shield it from direct sunlight and keep it away  
from sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes  
at the top and bottom of the unit. Do not place the  
unit on a carpet because this will block the ventila-  
tion holes.  
Unauthorized recording or use of broadcast televi-  
sion programming, video tape, film or other copy-  
righted material may violate applicable copyright  
laws. We assume no responsibility for the unautho-  
rized duplication, use, or other acts which infringe  
upon the rights of copyright owners.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the TV/VCR near strong magnetic fields.  
Avoid moving TV/VCR to locations where temper-  
ature differences are extreme.  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If, by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the  
TV/VCR cassette holder.  
Do not place anything directly on top of the unit.  
WARNING  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place,  
or after heating a cold room or under conditions of  
high humidity. If a tape is played in a TV/VCR  
which has moisture, it may damage the tape and  
TV/VCR. Therefore when the condensation occurs  
inside the unit, turn the POWER button on and allow  
at least 2 hours for the unit to dry out.  
3) Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
Download from Www.Somanuals.c-om4.-All Manuals Search And Download.  
EN  
9I03  
TABLE OF CONTENTS  
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2  
C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17  
AUTO REPEAT PLAYBACK . . . . . . . . . . . . .17  
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .18  
PICTURE CONTROLS . . . . . . . . . . . . . . . . . .19  
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4  
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
AVOID THE HAZARDS OF ELECTRICAL  
SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4  
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6  
C OPERATING CONTROLS AND FUNCTIONS 7  
C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .19  
NORMAL RECORDING . . . . . . . . . . . . . . . . .20  
SKIPPING UNWANTED SCENES DURING  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20  
OTR (One Touch Recording) . . . . . . . . . . . . . .20  
TIMER RECORDING . . . . . . . . . . . . . . . . . . .21  
TIMER PROGRAM EXTENSION . . . . . . . . .22  
C PREPARATION FOR USE . . . . . . . . . . . . . . . .9  
ANTENNA/CABLE CONNECTIONS . . . . . . .9  
INSTALLING THE BATTERIES . . . . . . . . . . .10  
EXTERNAL INPUT MODE . . . . . . . . . . . . . .10  
HINTS FOR AUTOMATIC TIMER  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23  
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10  
CHANNEL SET UP FOR THE FIRST TIME .10  
CLOCK SET UP (AUTO / MANUAL) . . . . . .11  
CHANNEL SET UP AGAIN . . . . . . . . . . . . . .12  
DELETING (OR ADDING) CHANNEL . . . . .12  
SELECTING THE LANGUAGE . . . . . . . . . . .13  
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .13  
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23  
WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24  
C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24  
C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25  
C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25  
REAL TIME TAPE COUNTER . . . . . . . . . . . .25  
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25  
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14  
WATCHING A TV PROGRAM . . . . . . . . . . . .14  
GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14  
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14  
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14  
CLOSED CAPTION SYSTEM . . . . . . . . . . . .15  
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15  
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25  
C TROUBLESHOOTING GUIDE . . . . . . . . . . .26  
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27  
C CABLE CHANNEL DESIGNATIONS . . . . . .27  
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover  
INDICE  
CONTROLES DE OPERACIÓN Y  
INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .30  
SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28  
PREPARACIÓN DE CANALES POR  
CONEXIONES DE ANTENA/CABLE . . . . . . . .30 PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31  
MODO DE ENTRADA EXTERNA . . . . . . . . . . .30 AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-  
tions concerning chemical wastes.  
- 5 -  
EN  
9I03  
 
FEATURES  
Infrared remote control  
Bilingual on screen menu display selectable in  
English or Spanish  
Zero Return–The tape returns to counter of  
0:00:00 by rewinding or fast forwarding.  
Still–“Freeze” the picture at any time, for close  
viewing of a particular scene. Only tapes recorded  
in SLP mode will show a fairly clear picture.  
Digital Auto Tracking (DTR)–Automatically  
adjusts the tracking for each tape you play.  
Rental play mode–Improves playback picture  
quality from worn tapes, such as rental tapes.  
Auto repeat–Allows you to repeat the playing of a  
tape indefinitely without pressing the PLAY button.  
Time search–Let you set the TV/VCR to advance  
the tape by entering the desired playback time you  
want to skip.  
OTR (One Touch Recording)–Instant timed  
recording from 30 to 480 minutes is possible at the  
push of the REC/OTR button.  
1 Year, 8 events (including Daily and Weekly  
Timer Recording)–The built-in timer allows you to  
record up to 8 programs at different times on dif-  
ferent channels up to 1 year in advance. The Daily  
timer allows recordings to be made of daily broad-  
casts, and the Weekly timer allows recording to be  
made once a week up to the end of the tape.  
Real time counter–This shows the elapsed record-  
ing or playback time in hours, minutes, and sec-  
onds. The “–” indication will appear when the tape  
is rewound further than the tape counter position  
“0:00:00”.  
181 channel capability PLL frequency synthesiz-  
er tuner with direct station call–(A converter may  
be necessary to view scrambled cable channels.)  
Auto Clock Setting–Allows you to set the clock  
function from a PBS broadcast station.  
Closed caption system–You may view specially  
labeled (cc) TV programs, movies, news, prere-  
corded tapes, etc. with either a dialogue caption or  
text display added to the program.  
Game mode–Automatically sets external input  
mode and allows TV/VCR display to be suitable  
for use with TV games.  
Auto power on and off system–Automatically  
turns on the TV/VCR when you insert the cassette,  
turns off after auto-rewind, and ejects when the  
beginning of the tape is reached.  
Auto rewind when the end of a tape is  
reached–This function doesn’t occur when using  
timer recording.  
2 Step picture search operation–You can view a  
video program at a high speed or super high speed  
in either a forward or reverse direction in LP and  
SLP mode. For SP mode only high speed.  
Three different playback tape speeds : SP/LP/SLP  
Two different recording tape speeds : SP/SLP  
Auto Head Cleaner–Automatically cleans video  
heads as you insert or remove a cassette.  
Auto return–After timer recording is finished, the  
TV/VCR can return to the beginning of the record-  
ing.  
Wake up/Sleep timer–Allows you to have the  
TV/VCR automatically turn on or off at a desired  
time.  
Timer Program Extension–Allow you to shift the  
time schedule for automatic timer recording.  
V-CHIP–Enables parents to prevent their children  
from watching inappropriate material on TV.  
SUPPLIED ACCESSORIES  
Remote Control Unit  
2 AA Batteries  
Rod Antenna  
(13” model only supplied  
19” model not supplied)  
PART NO. (0EMN00673 or  
0EMN01599 or 0EMN01755)  
PART NO. (N0150UD)  
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-  
968-3429.  
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators  
(Splitter). Contact your local electronics store for these items.  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control. If you decide to use a universal remote control with this unit, please be aware  
that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-  
versal remote control.  
Download from Www.Somanuals.c-om6.-All Manuals Search And Download.  
EN  
9I03  
OPERATING CONTROLS AND FUNCTIONS  
"
"
This manual covers 13 and 19 . The operation of the two models are exactly the same except  
"
the appearance. 19 model is illustrated in this manual.  
NOTE:  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control.  
If you decide to use a universal remote control with this unit, please be aware that the code number given  
may not operate this unit. In this case, please call the manufacturer of the universal remote control.  
- TV/VCR FRONT PANEL - [Fig.1]  
VIDEO AUDIO  
POWER  
CHANNEL  
STOP/EJECT  
REW PLAY F.FWD  
REC/OTR EARPHONE  
VOLUME  
13  
1 2 3 4 5 6 7 8 9101112  
14  
1 VIDEO input jack– Connect to the video output  
jack of your video camera or another VCR.  
2 AUDIO input jack– Connect to the audio output  
jack of your audio equipment, video camera or  
another VCR.  
3 POWER button– Press to turn TV/VCR on and  
off. Press to activate timer recording.  
4 VOLUME X / Y buttons– Adjust the volume  
level.  
5 CHANNEL K / L buttons– Press to select the  
desired channels for viewing or recording.  
You may display the main menu on the TV screen  
by pressing repeatedly this button on the  
TV/VCR.  
- REMOTE CONTROL - [Fig.2]  
25  
7
WAKE-UP  
POWER  
/SLEEP  
EJECT  
3
CHANNEL  
RETURN  
1
4
7
2
5
8
3
6
9
24  
15  
CHANNEL  
VOLUME  
5
4
0
+100  
MENU  
DISPLAY  
MUTE  
16  
17  
8
TRACKING function– Press to minimize video  
‘noise’ (lines or dots on screen) during playback  
mode. (See page 19.)  
6 Remote Sensor Window– Receives the infrared  
signals from the remote control.  
23  
9
PLAY  
10  
REW  
F.FWD  
STOP  
7
SPEED PAUSE/STILL  
RECORD  
7 STOP button– Press to stop the tape motion.  
EJECT button– Press in the Stop mode to remove  
tape from TV/VCR.  
22  
21  
11  
18  
T-PROG.  
CLEAR  
GAME  
TIME SEARCH  
COUNTER  
RESET  
L button–  
19  
20  
Press to select setting modes from the on screen  
menu.  
Press to enter digits when setting program.  
(for example: setting clock or timer program)  
- 7 -  
EN  
9I03  
 
- REAR VIEW - [Fig.3]  
ANT.  
26  
27  
+100 button– When selecting cable channels  
which are higher than 99, press this button first,  
then press the last two digits. (To select channel  
125, first press the “+100” button then press “2”  
and “5”).  
8 REW button– Press to rewind the tape, or to view  
the picture rapidly in reverse during playback  
mode. (Rewind Search)  
s button–  
Press to select a mode from a particular menu.  
16 MENU button– Press to display the main menu on  
the TV screen.  
17 DISPLAY button– Display the counter or the cur-  
rent channel number and current time on the TV  
screen. (See page 25.)  
18 SPEED button– Press to choose the desired  
recording speed:SP/SLP.  
19 T-PROG. CLEAR button– Press to cancel a setting  
of timer program. (See page 23.)  
COUNTER RESET button– Press to reset counter  
to 0:00:00.  
20 GAME button– Sets the game mode and external  
input mode at the same time. (See page 14.)  
21 TIME SEARCH button– Press to activate Time  
Search mode.  
22 PAUSE/STILL button– Press to temporarily stop  
the tape during the recording or to view a still pic-  
ture during playback.  
23 MUTE button– Mutes the sound. Press it again to  
resume sound.  
24 CHANNEL RETURN button– Press to go back to  
the previously viewed channel. For example,  
pressing this button once will change channel dis-  
play from 3 (present channel) to 10 (previously  
viewed channel), and pressing it a second time  
will return from 10 to 3.  
25 WAKE UP/SLEEP button– Sets the Wake up or  
Sleep Timer. (See page 23.)  
26 Power cord– Connect to a standard AC outlet  
(120V/60Hz).  
(for example: LANGUAGE or USER’S SET UP)  
9 PLAY button– Press to begin playback.  
K button–  
Press to select setting modes from the on screen  
menu.  
Press to enter digits when setting program.  
(for example: setting clock or timer program)  
10 F.FWD button– Press to rapidly advance the tape,  
or to view the picture rapidly in forward during  
playback mode. (Forward Search)  
B button–  
When setting program (for example: setting clock  
or timer program), press to determine your selec-  
tion and proceed to the next step you want to  
input.  
Press to determine setting modes from on screen  
menu.  
Press to select a mode from a particular menu.  
(for example: LANGUAGE or USER’S SET UP)  
11 REC button– Press for manual recording.  
OTR button– Activates One Touch Recording.  
(only on the TV/VCR)  
12 RECORD indicator– Flashes during recording.  
Lights up in the Stand-by mode for Timer  
Recording.  
13 EARPHONE jack– Connects to earphones (not  
supplied) for personal listening. The size of jack is  
1/8” monaural (3.5mm).  
14 Cassette compartment  
15 Number buttons– Press to select desired channels  
for viewing or recording. To select channels from  
1 to 9, first press the 0 button and then 1 to 9.  
27 ANT. terminal– Connect to an antenna or cable  
system.  
Download from Www.Somanuals.c-om8.-All Manuals Search And Download.  
EN  
9I03  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTIONS  
From Cable System or  
Satellite Dish  
VHF/UHF Antenna  
(Not supplied)  
Satellite Box or  
Cable Box  
(Not supplied)  
Rod Antenna  
(Supplied with 13” model only)  
OUT  
IN  
VHF Antenna  
(Not supplied)  
UHF Antenna  
(Not supplied)  
From  
Cable System  
or  
ANT.  
VHF/UHF  
Combiner  
(Not supplied)  
or  
ANT.  
or  
75-ohm Coaxial  
Cable (Not supplied)  
Flat twin-lead cable  
or  
VHF/UHF COMBINED ANTENNA  
VHF/UHF SEPARATE ANTENNAS  
The VHF/UHF Rod Antenna (supplied with 13”  
model only) is detachable. Insert the stem of the  
antenna into the hole on the upper-back portion of  
the TV/VCR. Connect the VHF/UHF Rod Antenna or  
VHF/UHF Combination Antenna to the ANT. termi-  
nal of the TV/VCR as shown in the diagram above.  
For the best reception, fully extend the VHF/UHF  
Rod Antenna and make the necessary adjustments.  
(Avoid touching the top section when adjusting.)  
NOTE:  
In some areas it will be necessary to use an outdoor  
antenna.  
CABLE WITHOUT CONVERTER/  
DESCRAMBLER BOX  
Use this connection if your cable system connects  
directly to your TV/VCR without a converter box.  
By using this connection you can:  
1) Use the TV/VCR remote to select channels.  
2) Program one or more unscrambled channels for  
Automatic Timer Recording.  
NOTE: This unit will ONLY record and view the  
same channel.  
Before plugging the Rod antenna into antenna termi-  
nal, check that the pin is not bent. If it is bent,  
straighten the pin as illustrated, then plug the pin into  
antenna terminal.  
CABLE WITH CONVERTER/  
DESCRAMBLER BOX OR SATELLITE  
BOX  
Bent pin  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown here.  
By using this connection you can also record scram-  
bled channels. However, channel selection must be  
made with the converter box or satellite box. This  
means that channels cannot be changed using the  
TV/VCR Remote Control. Unattended timer record-  
ing is limited to one channel at a time.  
Cable Plug  
(Straight pin)  
(Needs to be straightened)  
NOTE:  
The connection of an indoor antenna may not always  
give acceptable TV reception.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-  
ed to the grounding system of the building as close to the point of cable entry as practical.  
- 9 -  
EN  
9I03  
 
TO RECORD A SCRAMBLED/UNSCRAMBLED  
CHANNEL  
INSTALLING THE BATTERIES  
1. Set the TV/VCR channel selector to the output  
channel of the Cable Converter Box or Satellite  
Box. (Ex. CH3)  
2.Select the channel to record from your Cable  
Converter Box or Satellite Box.  
1)Open the battery compartment cover by pressing  
the cover on the remote unit in the direction of the  
arrow.  
2)Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
3)Replace the cover.  
EXTERNAL INPUT MODE  
When using an external input signal (another VCR or  
video camera), connect the player’s audio/video out-  
put cables to the AUDIO IN/ VIDEO IN jacks of  
your TV/VCR. Then press the CHANNEL K or  
button until “AUX” appears on the screen.  
NOTE: “AUX” is found below the  
lowest memorized channel.  
L
AUX  
(Example: CH2)  
SET UP FOR USE  
You can program the tuner to scan all the channels you receive in your area.  
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just  
select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then  
select the channel to be viewed on the Cable Box or Satellite Box.  
The tuner scans and memorizes all active channels in  
your area.  
NOTES:  
CHANNEL SET UP FOR THE  
FIRST TIME  
The TV/VCR distinguishes between standard TV  
channels and cable channels.  
1 Plug in the TV/VCR power cord  
Plug the TV/VCR power cord into a  
standard AC outlet.  
If you want to play or record a video tape  
BEFORE presetting the tuner, you must press the  
MENU button on the remote control. To preset the  
tuner again, see “CHANNEL SET UP AGAIN” on  
page 12.  
The TV/VCR may recognize TV channels to be  
CATV channels by the receiving conditions. In this  
case, try auto preset again in the fine receiving  
conditions.  
NOTE:  
If some digits appear in the corner of  
the screen, press the POWER button  
without unplugging the power cord.  
2 Turn on the TV/VCR  
Press the POWER button to turn on the TV/VCR  
5 After scanning  
3 Select “ENGLISH” or “ESPAÑOL”  
The tuner stops on the lowest memorized channel.  
If you want to recall the selected channels, you can  
select the desired channel directly with the remote  
control number buttons or CHANNEL K or L.  
– SET UP –  
Select “ENGLISH” or  
“ESPAÑOL”=Spanish using the  
F.FWD/B or REW/s button. “[ ]”  
indicate the selected language.  
B
LANGUAGE  
[ENGLISH] ESPAÑOL  
AUTO PRESET  
4 Begin auto preset  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO PRESET”.  
Then press the F.FWD/B button.  
– SET UP –  
LANGUAGE  
[ENGLISH] ESPAÑOL  
B
AUTO PRESET  
- 10 -  
EN  
9I03  
 
TO SELECT A DESIRED CHANNEL  
4 Select the day  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
You can select the desired channel by using the  
CHANNEL K or L button on or directly pressing  
the number buttons on the remote control.  
Note for using the number buttons:  
Press the PLAY/K or STOP/L but-  
ton until your desired day appears.  
(Example: 6th 06)  
0 5  
/
0 6 – – – – – – –  
HOUR  
– –  
MINUTE  
– – – –  
:
Then, press the F.FWD/B button.  
When selecting cable channels which are higher  
than 99, press the +100 button first, then, press the  
last two digits. (Example: to select channel 125,  
first press the +100 button then press “2” and “5”).  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
5 Select the year  
Press the PLAY/K or STOP/L but-  
ton until your desired year appears.  
(Example: 2003)  
0 5  
/
0 6 TUE 2 0 0 3  
You must proceed single-digit channel numbers  
with a zero (Example: 02 ... 09).  
HOUR  
– –  
MINUTE  
– – – –  
:
Then, press the F.FWD/B button.  
CLOCK SET UP  
6 Select the hour  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
(AUTO / MANUAL)  
Press the PLAY/K or STOP/L but-  
ton until your desired hour appears.  
(Example: 5, PM)  
0 5  
/
0 6 TUE 2 0 0 3  
HOUR  
0 5  
MINUTE  
– – PM  
The TV/VCR clock must be set correctly before  
VCR timer recording is possible. It is suggested that  
the clock be set manually when first setting up the  
TV/VCR. Then, setup auto clock correction which  
will periodically correct the setting if necessary.  
NOTE: If you cannot receive a station with time  
signals, auto clock setting cannot be performed. Use  
manual setting only.  
:
Then, press the F.FWD/B button.  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
7 Select the minute  
Press the PLAY/K or STOP/L but-  
ton until the desired minute  
appears. (Example: 40)  
0 5  
/
0 6 TUE 2 0 0 3  
HOUR  
0 5  
MINUTE  
4 0 PM  
:
MANUAL CLOCK SETTING  
8 Start the clock  
5:40 PM  
Make sure ...  
Press the MENU button on the  
remote control.  
The TV/VCR is turned on.  
In the example below, the clock is to be set to:  
Although seconds are not dis-  
played, they begin counting from  
00 when you press the MENU button on the remote  
control. Use this feature to synchronize the clock  
with the correct time.  
DATE  
May 6th, 2003  
SETTING TIME 5:40PM  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L  
button to point to “SETTING  
CLOCK”.  
– M E N U –  
NOTE:  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
When unplugging the AC cord or if there is a power  
failure for more than 3 seconds, you may have to  
reset the clock.  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Then, press the F.FWD/B button.  
TO CHANGE CLOCK SETTING  
If you want to change the clock,  
1)Follow steps [1] and [2].  
2)Select where you want to change using the  
F.FWD/B or REW/s button.  
3)Enter correct numbers using the PLAY/K or  
STOP/L button.  
2 Select “MANUAL CLOCK SET”  
Press the PLAY/K or STOP/L  
button to point to “MANUAL  
CLOCK SET”.  
– SETTING CLOCK –  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
B
[OFF]  
Then, press the F.FWD/B button.  
4)Press the MENU button on the remote control to  
start the clock.  
3 Select the month  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
Press the PLAY/K or STOP/L  
button until your desired month  
appears. (Example: May 05)  
Then, press the F.FWD/B button.  
PLEASE NOTE:  
If there is no local PBS station in your area or on  
your cable system, select “AUTO CLOCK” and  
press the F.FWD/B or REW/s button to turn [OFF]  
this function. Then you can manually adjust the  
clock.  
0 5  
/
– – – – – – – – –  
HOUR  
– –  
MINUTE  
– – – –  
:
- 11 -  
EN  
9I03  
 
AUTOMATIC CLOCK SETTING  
Make sure ...  
4 Enter the channel number that contains the  
The TV/VCR is turned on.  
Confirm the TV/VCR is receiving a RF (Radio  
Frequency) signal from either an antenna or cable  
system connection using the ANT IN jack on the  
rear of the TV/VCR.  
Automatic Clock Setting Signal  
Press the MENU button on the  
– M E N U –  
remote control.  
TIMER PROGRAMMING  
PICTURE CONTROL  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the PLAY/K or STOP/L  
button to select “SETTING  
CLOCK”.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
NOTE:  
TIME SEARCH  
If a cable converter box is being used, make sure it  
is powered on.  
Press the F.FWD/B button to  
enter “SETTING CLOCK” menu.  
Press the STOP/L button to select  
“AUTO CLOCK CH”.  
– SETTING CLOCK –  
You must use the TV/VCR remote control to per-  
form the clock setting procedure.  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
B
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[
45]  
[OFF]  
Press the F.FWD/B or REW/s  
buttons until you locate Auto  
Clock Set station number. See  
item 3 above.  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
remote control.  
B
Press the MENU button to exit the screen.  
Press the PLAY/K or STOP/L but-  
ton to select “SETTING CLOCK”.  
Press the F.FWD/B button to enter  
“SETTING CLOCK” menu.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
5 Turn off the TV/VCR  
Once the TV/VCR is turned off , it will periodically  
check and set the correct date and time.  
2 Set “AUTO CLOCK” to [ON]  
Press the F.FWD/B button until  
AUTO CLOCK [ON] appears.  
– SETTING CLOCK –  
B
AUTO CLOCK  
[ON]  
CHANNEL SET UP AGAIN  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
Make sure ...  
[OFF]  
Press the POWER button to turn on the TV/VCR.  
1 Select “CHANNEL SET UP”  
3 Begin “AUTO CLOCK CH SEARCH”  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
Press the STOP/L button to select “AUTO CLOCK  
PICTURE CONTROL  
remote control.  
SETTING CLOCK  
CH SEARCH”.  
B
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
Press the F.FWD/B button.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
– SETTING CLOCK –  
The TV/VCR is now searching  
TIME SEARCH  
AUTO CLOCK  
[ON]  
B
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
for the station which contain the  
auto clock set signal. The search  
for a signal may take up to 20  
seconds per channel.  
Then, press the F.FWD/B button.  
[OFF]  
2 Begin auto preset  
– CHANNEL SET UP –  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO PRESET”.  
Then, press the F.FWD/B button.  
The tuner scans and memorizes all  
the active channels in your area.  
“_ _” appears at the lower left of  
the screen when the search has  
ended.  
Auto Clock station- write down  
the number(s) that appear on the  
screen. These are the auto clock  
station(s) in your area. See item  
4 below.  
If no number(s) appear on the TV screen, there are  
no stations in your area which contain the Auto  
Clock signal. Auto Clock Setting is not possible.  
Please use Manual Clock Setting on page 11.  
Press the MENU button to exit the screen.  
NOTE: During Auto Clock CH Search, the picture  
may be distorted. This is normal.  
ADD / DELETE CH (TV)  
AUTO PRESET  
– AUTO CLOCK CH SEARCH –  
B
08  
10  
13  
_ _  
3 After scanning  
The tuner stops on the lowest memorized channel.  
DELETING (OR ADDING)  
CHANNEL  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you  
can add the deleted channel into the memory again.)  
- 12 -  
EN  
9I03  
 
1 Select “CHANNEL SET UP”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
2 Select “ENGLISH” or “ESPAÑOL”  
Select “ENGLISH” or “ESPAÑOL”= Spanish using  
the F.FWD/B or REW/s button.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
3 Exit the Language mode  
Press the MENU button on the remote control to  
return to TV mode.  
ZERO RETURN  
TIME SEARCH  
Then, press the F.FWD/B button.  
NOTE: If for some reason the menu is in Spanish,  
press the MENU button on the remote control, press  
the PLAY/K button to point to “IDIOMA  
[ESPAÑOL]”, then press the F.FWD/B button, then  
press the MENU button on the remote control.  
– CHANNEL SET UP –  
2 Select “ADD/DELETE CH”  
Press the PLAY/K or STOP/L but-  
ton to point to “ADD/DELETE  
CH”.  
B
ADD / DELETE CH (TV)  
AUTO PRESET  
Press the F.FWD/B button.  
DAYLIGHT-SAVING TIME  
Select this feature and the TV/VCR’s clock automati-  
cally will advance one hour in April, then reverse one  
hour in October.  
When Daylight-Saving Time is ON, the clock will  
change automatically as follows:  
First Sunday of April : At 2 AM the clock imme-  
diately changes to 3 AM. Any timer programming  
you have set to occur between 2 AM and 3 AM  
will not record.  
Last Sunday of October : At 2 AM the clock  
immediately changes to 1 AM.  
3 Enter the desired channel number  
Press the PLAY/K or STOP/L but-  
ton until your desired channel num-  
ber appears. (You can also use the  
number buttons or the CHANNEL  
K/L button to enter it) (Example:  
CH8)  
08  
ADD / DELETE  
4 Delete (or add) it from (into) memory  
Press the F.FWD/B or REW/s button. The channel  
number changes to light red. The channel is deleted  
from memory.  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
To delete another channel, repeat steps [3] and [4].  
If you press the F.FWD/B or REW/s button  
again, the channel is memorized again.  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
Added channel: Light blue.  
Deleted channel: Light red.  
– M E N U –  
remote control.  
TIMER PROGRAMMING  
PICTURE CONTROL  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to “SETTING  
CLOCK”.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
5 Exit the channel setup mode  
Press the MENU button on the remote control to  
returns to TV mode.  
TIME SEARCH  
Then, press the F.FWD/B button.  
NOTE: To confirm that channel(s) has been deleted  
or added, press the CHANNEL K or L button.  
2 Set “D.S.T.(Daylight-Saving Time) to [ON]  
– SETTING CLOCK –  
Press the PLAY/K or STOP/L but-  
ton to point to “D.S.T.”.  
Then, press the F.FWD/B or  
REW/s button until [ON] appears.  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
[ON]  
B
SELECTING THE LANGUAGE  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
NOTE: This function effects only the language on  
the screen menu and not the audio source.  
3 Exit the Daylight-Saving Time mode  
Press the MENU button on the remote control to  
return to TV mode.  
1 Select “LANGUAGE”  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
TO CANCEL THE DAYLIGHT-SAVING  
TIME  
Repeat steps [1] to [2], select [OFF] using the  
Press the MENU button on the  
remote control.  
V-CHIP SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to “LANGUAGE”.  
B
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
F.FWD/B or REW/s button.  
- 13 -  
EN  
9I03  
 
TV OPERATION  
WATCHING A TV PROGRAM  
PICTURE CONTROL  
The TV/VCR’s picture controls – BRIGHT, CON-  
TRAST, COLOR, TINT and SHARPNESS – are  
preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a natural looking image.  
NOTES:  
1 Turn on the TV/VCR  
Press the POWER button to turn on the TV/VCR.  
2 Select the channel number  
Press the CHANNEL K or L button to select your  
desired channel number or press the number buttons  
on the remote control.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be viewed must be selected  
on the cable box or satellite box.  
Procedures must be followed within 5 seconds or  
the Picture Control mode will be cancelled.  
When setting the Picture Control, the Game mode  
will be cancelled.  
Make sure ...  
TV/VCR power must be turned on.  
1 Select “PICTURE CONTROL”  
3 Adjust sound  
Press the MENU button on the  
X
Y
Press the VOLUME or button  
to adjust the volume.  
– M E N U –  
remote control.  
TIMER PROGRAMMING  
B
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to ”PICTURE CON-  
TROL”.  
VOLUME 20  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
C
C
C
C
C
C
C
C
C
C
C
C
TIME SEARCH  
Then, press the F.FWD/B button.  
GAME MODE  
2 Select item you want to adjust  
Press the PLAY/K or STOP/L button until desired  
This function enables you to decrease the TV screen  
contrast and making it suitable for use with a TV  
GAME.  
control is displayed.  
BRIGHT  
CONTRAST  
NOTE: This function can not be set during recording.  
BRIGHT  
COLOR  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
TINT  
Press the GAME button on the  
GAME  
remote control. “GAME” appears  
on the screen.  
SHARPNESS  
3 Adjust the picture control  
When you press the GAME button;  
Press the F.FWD/B or REW/s button to adjust to  
The TV/VCR comes on automatically if it is off.  
The TV/VCR will be in external input mode auto-  
your desired level.  
matically.  
TO CANCEL THE GAME MODE  
Press the GAME button or CHANNEL K or L but-  
ton on the remote control.  
REW/s  
to decrease  
brightness  
to decrease  
contrast  
F.FWD/B  
to increase  
brightness  
to increase  
contrast  
BRIGHT  
CONTRAST  
DEGAUSSING  
Magnetism from nearby appliances might affect the  
color of the TV picture.  
If this happens, move this unit away from the appli-  
ance. If the color is still not correct, disconnect  
power cord from AC outlet then reconnect it after 30  
minutes.  
COLOR  
TINT  
to pale  
to brilliant  
to purple  
SHARPNESS to soft  
to green  
to clear  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
- 14 -  
EN  
9I03  
 
TO CANCEL THE CLOSED CAPTION  
SYSTEM  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button. Press the MENU but-  
ton on the remote control to return to TV mode.  
CLOSED CAPTION SYSTEM  
You can view specially labeled (cc) TV programs,  
movies, news, pre-recorded tapes with either a dia-  
logue caption or text display.  
CAPTION mode: By choosing the caption mode, you  
can watch dramas, movies and news while captioning  
the dialogues and the contents of news.  
TEXT mode: By choosing the text mode, you can  
watch half screen text information if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. Caption “2” is used,  
usually for a second language if available.  
WHEN THE CLOSED CAPTION MODE  
IS ON  
The On-Screen Display will disappear after 5 sec-  
onds.  
This is also true when the MUTE button is pressed,  
and when the PAUSE/STILL button is pressed  
while recording.  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
NOTE:  
Not all programs are broadcast with closed captions.  
Your television is designed to provide error free  
closed captions from high quality antenna, cable and  
VCR signals. Conversely, poor quality signals are  
likely to result in caption errors or no captions at all.  
Common signal conditions which may cause captions  
errors are listed below:  
V-CHIP SET UP  
V-CHIP enables parents to prevent their children  
from watching inappropriate material on TV.  
V-CHIP reads the ratings for programming (except  
for news and sports programs, unedited movies on  
premium cable channels, and Emergency Broadcast  
System signals), then denies access to programming  
if the program’s rating meets the limitations you  
select. In this case, “PROTECTED PROGRAM by  
...” message appears on the TV screen.  
To block ratings, follow the steps below.  
Programming may be rated by the Motion Picture  
Association of America (MPAA) or according to  
the Television Parental Guidelines. In order to  
block any inappropriate programming, set your  
limits in both places (MPAA RATING and TV  
RATING).  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture  
ghosts or airplane flutter.  
Playback of poorly recorded or worn VCR tapes.  
NOTE:  
If the TV/VCR displays a black box on the TV  
screen, this means that the TV/VCR  
is set to the TEXT mode. To clear  
screen, select [CAPTION1], [CAP-  
TION2] or [OFF].  
Make sure ...  
TV/VCR power must be turned on.  
TV RATING SET UP  
– M E N U –  
1 Select “CAPTION”  
Make sure ...  
TIMER PROGRAMMING  
PICTURE CONTROL  
Press the MENU button on the  
SETTING CLOCK  
TV/VCR power must be turned on.  
CHANNEL SET UP  
USER’S SET UP  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “CAPTION”.  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
B
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
1 Select “V-CHIP SET UP”  
– M E N U –  
TIMER PROGRAMMING  
Press the MENU button on the  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
remote control.  
USER’S SET UP  
2 Select your desired caption menu  
Press the F.FWD/B or REW/s  
button until your desired caption  
menu appears.  
([CAPTION1], [CAPTION2],  
[TEXT1] or [TEXT2])  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Press the PLAY/K or STOP/L but-  
ton to point to “V-CHIP SET UP”.  
Then, press the F.FWD/B button.  
– M E N U –  
TIME SEARCH  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [CAPTION1]  
ZERO RETURN  
B
TIME SEARCH  
2 Select “TV RATING”  
Press the PLAY/K or STOP/L but-  
ton to point to “TV RATING”.  
Then, press the F.FWD/B button.  
– V-CHIP SET UP –  
B
TV RATING  
MPAA RATING  
3 Exit the caption setting mode  
Press the MENU button on the remote control to  
return to TV mode.  
- 15 -  
EN  
9I03  
 
3 Select your desired item  
Press the PLAY/K or STOP/L button to point to  
your desired item.  
4 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
return to original mode.  
Then, press the F.FWD/B button to  
select [BLOCK] or [VIEW].  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
MPAA RATING SET UP  
(
)
)
)
)
(
Make sure ...  
When you select the rating cate-  
gory and turn it [BLOCK], the  
higher rating will turn [BLOCK]  
TV/VCR power must be turned on.  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
When you turn “TV-Y” to [VIEW], the all ratings  
will turn to [VIEW] automatically.  
1 Select “V-CHIP SET UP”  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “V-CHIP SET UP”.  
Then, press the F.FWD/B button.  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Selection  
TV-Y  
Rating Category Explanations  
Appropriate for all children  
TIME SEARCH  
TV-Y7  
TV-G  
TV-PG  
TV-14  
Appropriate for children seven and older  
General Audience  
Parental Guidance suggested.  
Unsuitable for children under 14  
– V-CHIP SET UP –  
2 Select “MPAA RATING”  
Press the PLAY/K or STOP/L but-  
ton to point to “MPAA RATING”.  
Then, press the F.FWD/B button.  
TV RATING  
MPAA RATING  
B
TV-MA Mature audience only  
When you select TV-Y7, TV-PG, TV-14, or TV-MA  
and you press the F.FWD/B button, the sub-ratings  
will appear on the TV screen.  
If you select the rating category (example: TV-PG)  
and turn it [BLOCK] or [VIEW], the sub-ratings  
(example: V for Violence) will turn [BLOCK] or  
[VIEW] automatically.  
3 Select your desired item  
Press the PLAY/K or STOP/L but-  
ton to point to your desired item.  
Then, press the F.FWD/B button to  
select [BLOCK] or [VIEW].  
G
[VIEW]  
PG  
[VIEW]  
PG–13  
R
NC–17  
X
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
You can set the sub-ratings to [BLOCK] or [VIEW]  
individually when the rating category is set to  
[BLOCK].  
To set the sub-ratings individually, follow the steps  
below.  
Selection  
G
PG  
PG-13  
R
Rating Category Explanations  
General Audience  
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
When you select [TV-Y7]:  
TV–Y7  
FV  
[BLOCK]  
[BLOCK]  
Press the STOP/L or PLAY/K  
button to select “FV” (Fantasy  
Violence).  
B
NC-17  
X
Mature audience only  
Then, press the F.FWD/B button  
to select [BLOCK] or [VIEW].  
When you select [TV-PG], [TV-14] or [TV-MA]:  
Press the STOP/L or PLAY/K  
When you select the rating category and turn it  
[BLOCK], the higher rating will turn [BLOCK]  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
When you turn “G” to [VIEW], the all ratings will  
turn to [VIEW] automatically.  
button to select “D”(Suggestive  
TV–PG  
[BLOCK]  
B
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
Dialog), “L”(Coarse Language),  
“S”(Sexual Situation), or  
“V”(Violence). Then, press the  
F.FWD/B button to select  
[BLOCK] or [VIEW].  
Note: When you select [TV-MA], “D” does not  
appear on the TV screen.  
4 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
return to original mode.  
The sub-ratings which set to  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
(
)
[VIEW]  
[VIEW]  
[BLOCK] appears next to the rat-  
ing category in the TV RATING  
menu.  
[BLOCK]  
[BLOCK]  
[BLOCK]  
- 16 -  
EN  
9I03  
 
PLAYBACK  
This TV/VCR will operate with any cassette that has the  
mark. For best results, we  
recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.  
INSERTING A CASSETTE  
Insert the cassette in the direction as shown. Push in  
gently, but continuously, on the center-back of the  
cassette until it is drawn into the TV/VCR. The  
TV/VCR will automatically turn on.  
AUTO REPEAT PLAYBACK  
The TV/VCR has the auto repeat function that allows  
you to repeat a tape indefinitely without touching the  
PLAY button.  
ALL REPEAT: Repeat playback from the beginning  
to the end of the tape.  
BLANK REPEAT: Repeat playback from the begin-  
ning to a blank part, which is blank for more than  
10 seconds.  
Window  
WRONG  
CORRECT  
1 Select “USER’S SET UP”  
PRECAUTIONS  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
Avoid moisture. Moisture condensation may occur  
on the tape if it is moved from a cold place to a  
warm place or visa versa. Before using a tape with  
these conditions, to avoid damage of the tape and  
your TV/VCR, wait until the tape has warmed to  
room temperature and the moisture has evaporated.  
Avoid extreme heat, high humidity and magnetic  
fields.  
remote control.  
SETTING CLOCK  
CHANNEL SET UP  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
2 Select “ALLor “BLANK”  
Press the PLAY/K or STOP/L button to point to  
“REPEAT PLAY”.  
Press the F.FWD/B or REW/s  
button repeatedly until your desired  
selection [ALL] or [BLANK]  
appears.  
Do not tamper with the cassette mechanism.  
Do not touch the tape with your fingers.  
USER’S SET UP  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[ALL]  
[OFF]  
B
NORMAL PLAYBACK  
Make sure ...  
TV/VCR power must be turned on.  
3 Exit the Repeat Play setting  
Press the MENU button on the remote control to  
return to the TV mode.  
1 Insert a prerecorded tape  
If the erase-protection tab has been removed, the  
TV/VCR will start playback automatically.  
4 Start playback  
Press the PLAY button to start the Repeat Play.  
”REPEAT PLAY B” appears.  
B
PLAY  
2 To begin playback  
Press the PLAY button.  
Once you select the Repeat Play mode, it stays in  
effect even after you turn off the TV/VCR.  
If the Rental mode is set [ON], the “RENTAL  
PLAY B” display has priority.  
Note: If any menu is activated on  
the screen, the PLAY button does  
not function. Press the MENU but-  
ton to clear the menu. then, press  
the PLAY button.  
STOP  
3 To stop playback  
Press the STOP button when play-  
back is completed.  
TO CANCEL THE REPEAT PLAY MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
- 17 -  
EN  
9I03  
 
NOTES:  
SEARCH  
Time Search can be set up to a maximum of 9  
hours 50 minutes (9:50) by 10 minutes at a time.  
PICTURE SEARCH  
This feature is very useful in finding or skipping over  
a particular scene on a tape. In this mode, the sound  
will be muted.  
This function will not operate in recording mode.  
In the example below: To watch a program after 2  
hour 50 minutes from the present position, in either  
direction.  
1)You may view a video tape at a high speed in  
either a forward or reverse direction by pressing  
the F.FWD or REW button during playback. (in the  
SP / LP / SLP modes)  
2)Press it again and the TV/VCR will now search in  
super high speed. (in the LP / SLP modes only)  
NOTE: Tapes recorded in the SP or LP mode will  
display a noise bar on the TV screen and the pic-  
ture may revert to Black and White. This is normal.  
3)Press the PLAY button to return to normal speed.  
1 Insert a tape.  
2 Select “TIME SEARCH” mode  
Press the TIME SEARCH button (with each push it  
will increase by 10 minutes).  
3 Enter your desired time  
Press the PLAY/K or STOP/L but-  
TIME SEARCH  
2 : 50  
ton until your desired time appears.  
(Example: “2:50” stands for 2 hours  
50 minutes)  
If you wish to cancel the Time Search at this point,  
press the MENU button on the remote control.  
ZERO RETURN  
This function allows you to search easily a beginning  
point that you want to review by rewinding or fast  
forwarding.  
NOTE:  
4 Begin Time Search  
Zero Return WILL NOT work on a blank tape or a  
blank portion of a tape.  
By pressing the REW/s or F.FWD/B button, the  
TV/VCR will rewind or fast forward to the specified  
point.  
1 Stop a tape at your desired point  
Rewind or fast forward the tape to the beginning  
point at which you want to review.  
The time counts down as the searching progresses.  
When 0:00 is reached, the tape will start playback  
automatically.  
2 Reset the counter to 0:00:00  
Press the COUNTER RESET button repeatedly.  
TO CANCEL THE TIME SEARCH at this  
point  
Press the STOP/EJECT button on the TV/VCR or the  
remote control. This will delete the selected time.  
3 Begin recording or playback  
Press the RECORD or PLAY button.  
Press the STOP button when recording or playback is  
completed.  
STILL PICTURE  
You can view a still picture on the TV screen during  
playback (the Still mode). Press the PAUSE/STILL  
button during playback. Only tapes recorded in the  
SLP mode will show the least amount of lines.Press  
the PLAY button to return to playback.  
NOTES:  
4 To activate “ZERO RETURN” mode  
Press the MENU button on the remote control.  
Press the PLAY/K or STOP/L button to point to  
“ZERO RETURN”.  
– M E N U –  
TIMER PROGRAMMING  
Then, press the F.FWD/B button.  
PICTURE CONTROL  
Usually there will be video “noise” lines (black  
and white streaks or dots) on the screen. This is  
normal.  
SETTING CLOCK  
CHANNEL SET UP  
The counter will appear on the TV  
screen.  
The tape will automatically stop  
when the counter returns to 0:00:00.  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
B
TIME SEARCH  
If the tape was originally recorded in SP or LP  
mode, the still picture will be black and white in  
addition to the “noise” lines.  
This is not a fault of the machine, but is a by-  
product of the technology involved in producing  
a TV/VCR with 2 video heads.  
TIME SEARCH  
The Time Search function makes it possible to  
quickly advance the tape to your desired position  
simply by entering the exact amount of playback  
time you want to skip.  
If it is left in the Pause mode for more than five  
minutes, the TV/VCR will automatically switch to  
the Stop mode.  
- 18 -  
EN  
9I03  
 
NOISE CANCEL (in the Still mode)  
RENTAL PLAYBACK  
This feature allows you to reposition or reduce the  
noise lines of a still picture.Press the PAUSE/STILL  
button so that the noise lines change position on the  
screen so you can see the picture in its entirety with-  
out distracting noise lines.  
NOTE: This feature can be activated ONLY when  
viewing a tape recorded in the SLP mode. If the tape  
was originally recorded in the SP or LP mode, the  
still picture may revert to black and white in addition  
to the “noise bars”. This is normal.  
This function enables you to improve the picture  
quality when playing back worn cassettes such as  
rented tapes.  
1 Select “USER’S SET UP”  
– M E N U –  
TIMER PROGRAMMING  
Press the MENU button on the  
PICTURE CONTROL  
SETTING CLOCK  
remote control.  
CHANNEL SET UP  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
VERTICAL HOLD CONTROL  
In the Pause/Still mode only, when the picture begins  
to vibrate vertically, stabilize the picture by pressing  
the CHANNEL K or L button.  
USER’S SET UP  
2 Set “RENTALto [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “RENTAL”.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
B
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[ON]  
[OFF]  
[OFF]  
NOTE:  
If there are video noise lines on the screen, reposition  
or reduce them. Refer to “NOISE CANCEL”.  
3 Exit the Rental setting  
Press the MENU button on the remote control to  
return to the TV mode.  
PICTURE CONTROLS  
TRACKING ADJUSTMENT  
4 Start playback  
Tracking adjustment will be set automatically  
(Digital Tracking function) when you start play-  
back.  
Press the PLAY button to start playback. “RENTAL  
PLAY B” appears.  
Once you select the Rental mode, it stays in effect  
even after you turn off the TV/VCR.  
However when playing pre-recorded tapes or tapes  
recorded on units other than your own, noise lines  
(black and white streaks) may appear on the play-  
back picture. If this occurs, you can adjust the  
tracking control manually by pressing the CHAN-  
NEL K or L button until the streaks disappear. To  
return to the DTR function, stop the tape once and  
start playback again.  
TO CANCEL THE RENTAL MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
RECORDING  
TWO DIFFERENT TAPE SPEEDS  
ERASE PREVENTION  
Before recording, select the tape speed from : SP  
mode (Standard Play) or SLP mode (Super Long  
Play).  
The table below shows the maximum recording/play-  
back time using T60, T120 or T160 tapes in each  
mode.  
You can prevent accidental  
erasing of recording by  
breaking off the tab on the  
back edge of the cassette.  
Tab  
Tape Speed  
Type of tape  
SP mode  
Recording/Playback Time  
If you decide to record on  
the tape again, cover the  
hole with plastic tape.  
T60  
1 hour  
3 hours  
T120  
T160  
2 hours 2-2/3 hours  
6 hours 8 hours  
SLP mode  
Note: You can play back a tape recorded in LP mode  
(Long Play).  
Transparent Tape  
- 19 -  
EN  
9I03  
 
Make sure ...  
TV/VCR power must be turned on.  
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to  
the point at which you want to begin recording.)  
NOTE: This unit will ONLY record and view the same channel.  
NORMAL RECORDING  
OTR (One Touch Recording)  
You can ONLY watch the same TV program that is  
being recorded.  
This function enables you to set a recording length  
simply by pressing the REC/OTR button on the  
TV/VCR.  
Make sure ...  
1 Select the channel to be recorded  
TV/VCR power must be turned on.  
Insert a cassette tape with its erase prevention tab  
Press the number buttons on the  
CH 10  
remote control or the CHANNEL  
K or L button.  
in place. (If necessary, rewind or fast forward the  
Remember: If the TV/VCR is con-  
nected to a cable box or satellite  
box, the TV/VCR must be on CH3  
or CH4, then the channel to be recorded must be  
selected on the cable box or satellite box.  
tape to the point at which you want to begin  
recording.)  
NOTES:  
This function CANNOT be done from the remote  
control.  
Recording starts immediately when the REC/OTR  
button is pressed.  
When the REC/OTR button is pressed 18 times, the  
TV/VCR returns to the Normal Recording mode.  
2 Select the tape speed  
Press the SPEED button to select  
the desired tape speed (SP/ SLP).  
To stop the OTR operation, press the STOP button  
on the TV/VCR or on the remote control.  
SP  
To show the remaining time, press the DISPLAY  
button on the remote control so that “OTR”  
appears on the TV screen. (It will show up momen-  
tarily then disappear.)  
REC  
3 Begin recording  
Press the RECORD button.  
Recording stops when 0:00 is reached.  
Please note that in the SLP mode maximum record-  
ing time, assuming the tape is started at the begin-  
ning, is 8 hours using T-160 (or 6 hours using T-120).  
SP  
4 Stop recording  
Press the STOP button when recording is completed.  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, ejects the tape and turns itself off.  
If you press the power button during OTR, the  
TV/VCR continues recording until the selected  
length is reached.  
SKIPPING UNWANTED  
SCENES DURING RECORDING  
Press the PAUSE/STILL button to  
PAUSE  
temporarily stop recording.  
Press the PAUSE/STILL or  
RECORD button to resume record-  
ing.  
NOTES:  
1 Select the channel to be recorded  
Press the number buttons on the remote control or the  
CHANNEL K or L button.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be recorded is selected on  
the cable box or satellite box.  
SP  
After five minutes, the TV/VCR will automatically  
switch to the Recording mode to prevent tape dam-  
age.  
If “CLOSED CAPTION (ON)” is selected, the On-  
Screen Display will appear for 5 seconds, then dis-  
appear.  
2 Select the tape speed  
Press the SPEED button to select the desired tape  
speed (SP/ SLP).  
- 20 -  
EN  
9I03  
 
Avoid over lap of programs ...  
There is a chance that a program will not be recorded  
when programs overlap;  
3 Begin OTR  
OTR(2 : 30)  
Press the REC/OTR button on the  
TV/VCR as many times as needed.  
The recording length will be deter-  
mined by the number of times you  
press the REC/OTR button. Each  
The program with an earlier start has priority.  
Once the earliest program finishes, the overlapping  
programs will begin recording in sequence.  
SP  
The illustration below demonstrates the sequence  
of recordings.  
additional push will increase the recording time by  
30 minutes. It is set up to 8 hours.  
Recording Sequence  
Push(es) Display  
1 push  
Recording length  
(normal recording)  
Program 1  
10:00AM-11:00AM  
Program 2  
9:00AM-10:00AM  
Program 3  
2 pushes  
3 pushes  
0:30  
1:00  
30 minutes  
60 minutes  
9:30AM-12:00PM  
9:00AM  
10:00AM  
11:00AM  
12:00PM  
*Recording period is SHADED  
17 pushes  
8:00  
480 minutes  
1 Select “TIMER PROGRAMMING”  
Press the MENU button on the  
TIMER RECORDING  
– M E N U –  
remote control.  
B
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
Confirm “TIMER PROGRAM-  
MING” is pointed by pressing the  
PLAY/K button.  
You may set the TV/VCR to start and end a record-  
ing while you are away. You can set 8 programs to  
record on specific days, daily or weekly within a 1  
year period.  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
And press the F.FWD/B button.  
If you have not yet set the clock, “MANUAL  
CLOCK SET” appears. If so, follow stops [3] to  
[8] on page 11. Then set the timer recording.  
In the example below, the timer is being set to record:  
DATE:  
July 4th, 2003  
SETTING TIME: from 7:30PM to 8:50PM  
CHANNEL:  
TAPE SPEED:  
CH61  
SP  
2 Select your desired program position (1~8)  
– TIMER PROGRAMMING –  
Press the PLAY/K or STOP/L but-  
ton to select the desired program  
position.  
Make sure ...  
CH DATE  
BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
If a cable box or satellite box is connected with the  
TV/VCR you will be limited to record only one  
channel. And the channel selector on the TV/VCR  
must be selected to the output channel of the boxes  
CH 3 or CH 4 and then the actual channel to be  
recorded must be selected on the boxes.  
Clock must be set to the correct time and date  
before setting the timer.  
TV/VCR power must be turn on to program it.  
Insert a cassette tape with its erase prevention tab  
in place. (If necessary, rewind or fast forward the  
tape to the point at which you want to begin  
recording.)  
B
Then, press the F.FWD/B button.  
3 Set the channel number  
Press the PLAY/K or STOP/L but-  
ton until the desired channel num-  
ber appears.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
(Example: CH61)  
Then, press the F.FWD/B button.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be recorded is selected on  
the cable box or satellite box.  
The channel you want to record is properly set in  
advance.  
4 Select once, every day or weekly recording  
For once recording :  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Press the PLAY/K (up) button  
until the desired date appears.  
(Example: “7/04” for July 4th).  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 7/04 FRI -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
- 21 -  
EN  
9I03  
 
For every day recording : To record a TV program at  
the same time on the same channel every day.  
10 Finish setting the program  
Press the F.FWD/B or REW/s button. The program  
is now completed.  
(Example: Monday through Sunday)  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Press the STOP/L (down) button  
until “EVRY DAY” appears.  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY DAY -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
To set another program, repeat steps [2] to [10].  
Press the MENU button on the remote control to  
return to original mode.  
For weekly recording : To record a TV program at  
11 Set the timer  
Press the POWER button to set automatic timer  
recording. The RECORD indicator lights up.  
the same time on the same channel every week.  
(Example: every Monday)  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Press the STOP/L (down) button  
until “EVRY” and your desired  
day of the week appear together.  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
You must turn off the TV/VCR to activate automat-  
ic timer recording.  
If power is not turned off and you continue watch-  
ing TV, TIMER REC STANDBY” starts flashing  
on the TV screen 2 minutes before the programmed  
start time.  
B
5 Set beginning hour  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “ 7, PM” for 7:30PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
TIMER PROGRAM EXTENSION  
61 7/04 FRI 7:12P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
B
B
To shift the time schedule of an automatic timer  
recording.  
1)Press the POWER button.  
2)Repeat step [1] on page 21.  
6 Set beginning minute  
Press the PLAY/K or STOP/L but-  
ton until the desired minute appears.  
(Example: “30” for 7:30PM)  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
3)Press the RECORD button and select the desired  
program using the PLAY/K or STOP/L button.  
4)Press the RECORD button again.  
Each additional push will shift forward the  
begin/end time for recording by 10 minutes. When  
the recording is already in progress, each additional  
push will shift forward the end time only. If you  
want to cancel while setting, press the  
PAUSE/STILL button on the remote control. The  
recording time returns to the original time.  
NOTE: When you shift forward the time schedule  
during recording, the recording speed will automati-  
cally be set to the SLP mode.  
5)Press the F.FWD/B or REW/s button to exit the  
setting menu. Then press the MENU button on the  
remote control to return to original mode.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
Then, press the F.FWD/B button.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
7 Set end hour  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “8, PM” for 8:50PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:30PM - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
8 Set end minute  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
Press the PLAY/K or STOP/L but-  
ton until the desired minute appears.  
(Example: “50” for 8:50PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PM- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
TO CORRECT A PROGRAM  
While setting a program; press the REW/s but-  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
9 Set the tape speed  
Press the PLAY/K or STOP/L but-  
ton until the desired tape speed  
appears. (Example: SP)  
ton to go back one step and enter the correct num-  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PMSP  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
bers using the PLAY/K or STOP/L button.  
After setting a program;  
1)Press the POWER button.  
61 7/04 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
2)Repeat steps [1] - [2] on page 21.  
3)Press the F.FWD/B button (or press the REW/s  
button to go back one step) until the part you  
want to correct begins flashing, then make the  
changes pressing the PLAY/K or STOP/L but-  
ton.  
4)Press the POWER button to set automatic timer  
recording.  
- 22 -  
EN  
9I03  
 
TO CANCEL AN AUTOMATIC TIMER  
RECORDING  
USER’S SET UP  
2 Set “AUTO RETURN” to [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO RETURN”.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[OFF]  
[ON]  
After setting a program;  
1)Press the POWER button.  
B
2)Repeat steps [1] ~ [2] on page 21 and select a  
program you want to cancel.  
3)Press the T-PROG. CLEAR button.  
4)Press the MENU button on the remote control to  
return to TV mode.  
While recording is in progress;  
1)Press POWER button.  
3 Auto Return will begin  
When all the timer recordings are completed, the  
TV/VCR will rewind to the beginning of the recorded  
program(s).  
NOTE:  
If you press the POWER button while tape is  
rewinding, the Auto Return will stop.  
2)Press the STOP/EJECT button on the TV/VCR.  
TO CHECK THE BEGIN/END TIME  
1)Press the POWER button so that the REC indicator  
goes off.  
2)Press the MENU button on the remote control.  
3)Confirm “TIMER PROGRAMMING” is pointed.  
4)Press the F.FWD/B button. The details of pro-  
grams appear on the TV screen.  
4 Watch the recorded program  
Press the PLAY button.  
TO CANCEL THE AUTO RETURN  
MODE  
5)Press the MENU button on the remote control to  
return to TV mode.  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
HINTS FOR AUTOMATIC  
TIMER RECORDING  
WAKE UP TIMER  
The Wake Up Timer function turns on the TV/VCR  
without using the POWER button after a desired  
period of time.  
Make sure the channel you want to record is prop-  
erly set in advance.  
It is not necessary to press the RECORD button for  
timer recording.  
Recording begins automatically at the Start time.  
If you are recording using a Timer mode, you may  
not operate the unit manually.  
The erase-prevention tab on the cassette must be in  
place (or you must put tape over the hole).  
If the erase-prevention tab is removed, the cassette  
will be ejected when the POWER button is pressed  
to off.  
NOTES:  
Use the remote control for this procedure.  
Clock must be set to the correct time before setting  
the timer.  
If you want to select [TAPE], you must insert a  
cassette tape in the TV/VCR. The tape will start  
playback automatically on your desired time.  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, and the tape will be ejected.  
1 Select “WAKE UP TIMER”  
Press the WAKE UP/SLEEP button  
on the remote control once, and  
confirm “ON/OFF” is pointed.  
AUTO RETURN  
WAKE UP B ON/OFF  
[ON]  
TIMER  
TV/TAPE  
TIME  
[TV]  
Press the F.FWD/B or REW/s  
[12:00AM]  
button until [ON] appears.  
With this feature, after timer recording is finished,  
the beginning of the recorded program(s) can be  
searched for automatically.  
2 Select “TV” or “TAPE”  
Press the PLAY/K or STOP/L but-  
ton until to point to “TV/TAPE”.  
Press the F.FWD/B or REW/s  
button, and select [TV] or [TAPE].  
– M E N U –  
1 Select “USER’S SET UP”  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the MENU button on the  
WAKE UP  
TIMER  
ON/OFF  
B TV/TAPE  
TIME  
[ON]  
B
remote control.  
[TV]  
[12:00AM]  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
- 23 -  
EN  
9I03  
 
3 Set wake up time  
1 Select “SLEEP TIMER”  
Press the PLAY/K or STOP/L but-  
ton until to point to “TIME”.  
Press the F.FWD/B or REW/s  
button until your desired wake up  
time appears.  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
WAKE UP  
TIMER  
ON/OFF  
[ON]  
2 Set sleep time  
Press the PLAY/K, STOP/L,  
F.FWD/B or REW/s button until  
your desired sleep time appears.  
TV/TAPE  
[TV]  
B TIME  
[12:00AM]  
Each additional push will increase (or decrease) the  
time by 10 minutes.  
SLEEP TIMER [2:00]  
Each additional push will increase  
4 Exit the Wake Up Timer setting  
Press the MENU button on the remote control to  
return to TV mode.  
the time by 30 minutes up to 120 minutes.  
Press the MENU button on the remote control to exit  
the Sleep Timer setting.  
TO CANCEL THE WAKE UP TIMER  
TO CANCEL THE SLEEP TIMER  
Repeat step [1] but select [OFF].  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
To view the time left for sleep timer press the WAKE  
UP/SLEEP button twice, then press the MENU but-  
ton on the remote control to exit the sleep timer set-  
ting.  
SLEEP TIMER  
The Sleep Timer function turns off the TV/VCR  
without using the POWER button after a desired  
period of time.  
NOTE:  
This function does not operate during Recording  
mode.  
COPYING A VIDEO TAPE  
1)Insert a pre-recorded video cassette into the Source  
(Playing) VCR or camcorder.  
You can make copies of video tapes made by friends  
or relatives for your enjoyment.  
2)Insert a blank video cassette, or one you want to  
record over, into the TV/VCR’s cassette compart-  
ment.  
3)Press the SPEED button on remote control for the  
TV/VCR to select the desired recording speed  
(SP/SLP).  
WARNING: Unauthorized recordings of  
copyrighted video tapes may be an  
infringement of copyright laws.  
Connect your TV/VCR and a Source (Playing) VCR  
using the following diagram.  
4)Press the CHANNEL K or L button on the  
TV/VCR until “AUX” appears on the screen.  
NOTE: “AUX” is found below the lowest memo-  
rized channel. (Example: CH2)  
5)Press the RECORD button on the TV/VCR.  
6)Begin playback of the tape in the source (Playing)  
VCR or camcorder.  
[Fig.8]  
VIDEO AUDIO  
[The TV/VCR]  
NOTE: For best results during dubbing, use the  
TV/VCR’s front panel controls whenever possible.  
The remote control might affect the source (Playing)  
VCR’s playback operation.  
[Ex: Source (playing)  
VCR or camcorder]  
Audio/Video  
adapter cable  
(not supplied)  
AUDIO  
OUT  
IN  
VIDEO  
- 24 -  
EN  
9I03  
 
ON SCREEN DISPLAY  
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote  
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:  
WHEN THE CLOSED CAPTION MODE IS OFF:  
<Off mode>  
<Counter mode>  
<Clock mode>  
Counter mode: After 5 seconds, only  
the counter remains. To clear it, press  
the DISPLAY button.  
Clock mode: After 5 seconds, only  
the clock and the channel number  
remain. To clear them, press the DIS-  
PLAY button.  
5:40PM  
CH2  
Press  
once  
Press  
once  
COUNT 0:12:34  
Press once  
ON:  
OFF mode  
Clock/Counter mode  
WHEN THE CLOSED CAPTION MODE IS  
The On Screen Display disappear after 5 seconds.  
STOP  
5:40 PM  
CH2  
This is true even if the MUTE button is pressed, or the  
PAUSE/STILL button is pressed while recording.  
SP  
COUNT 0:12:34  
SPECIAL FEATURES  
REAL TIME TAPE COUNTER  
AUTO REWIND-EJECT  
This shows the elapsed recording or playback time in  
hours, minutes, and seconds. (The displayed time  
will not change on a blank tape or blank portions on  
the tape.)The “–” indication will appear when the  
tape has rewound further than “0:00:00” on the tape  
counter.  
When the end of a tape is reached during record-  
ing, playback, or fast-forward, the tape will auto-  
matically rewind to the beginning. After rewinding  
finishes, the TV/VCR will eject the tape and turn  
itself to off.  
This function is operative when Repeat Play is set  
to the [OFF] position.  
The tape will not auto-rewind during timer record-  
ing or One Touch Recording.  
MAINTENANCE  
back, the video heads in your TV/VCR may need  
to be cleaned.  
CABINET CLEANING  
Wipe the front panel and other exterior surfaces of  
the TV/VCR with a soft cloth immersed in luke-  
warm water and wrung dry.  
1.Please visit your local Audio/Video store and pur-  
chase a good quality VHS Video Head Cleaner.  
2.If a Video Head Cleaner does not solve the prob-  
lem, please call our help line at 1-800-968-3429, to  
locate an Authorized Service Center.  
NOTES:  
Remember to read the instructions included with  
the video head cleaner before use.  
Clean video heads only when problems occur.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the TV/VCR. Such chemicals  
may cause damage and discoloration to the  
exposed surfaces.  
AUTO HEAD CLEANING  
Automatically cleans video heads as you insert or  
remove a cassette, so you can see a clear picture.  
SERVICING  
Should your TV/VCR become inoperative, do not  
try to correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug the  
power cord, and please call our help line at 1-800-  
968-3429, to locate an Authorized Service Center.  
Playback picture may become blurred of interrupt-  
ed while the TV program reception is clear. Dirt  
accumulated on the video heads after long periods  
of use, or the usage of rental or worn tapes can  
cause this problem.  
If a streaky or snowy picture appears during play-  
- 25 -  
EN  
9I03  
 
TROUBLESHOOTING GUIDE  
If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,  
locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to  
remedy the problem.  
PROBLEM  
CORRECTIVE ACTION  
Make sure the AC cord is connected to an AC outlet.  
Make sure the power is turned on.  
Make sure the AC cord is connected to an AC outlet.  
Check antenna connection.  
Let the TV/VCR program its tuner memory.  
Adjust direction or replace antenna.  
Adjust picture controls.  
Adjust volume control on remote control or main unit.  
Press the MUTE button to restore sound.  
Make sure the timer recording is set correctly.  
Make sure the power is off.  
Make sure the TV/VCR clock is set correctly.  
Make sure the tape has an erase-prevention tab. If need, cover the  
hole with plastic tape.  
No power.  
No picture and sound.  
No picture or poor picture on  
TV/VCR.  
No sound or poor sound.  
Timer recording is not possible.  
Cannot go into Record mode.  
Playback picture is partially noisy.  
Adjust tracking control for a better picture using the CHANNEL  
or L button on the TV/VCR.  
Head cleaning may be necessary. Refer to “AUTO HEAD  
CLEANING” on page 25.  
K
No picture but the audio is OK in  
playback.  
No operation by infrared Remote  
Control.  
Video or color fades in and out  
when making a copy of a video tape  
Different color marks on screen.  
Make sure the AC cord is connected to an AC outlet.  
Check batteries in remote control.  
You can not copy a copyrighted video tape. You are experiencing  
copy guard protection.  
Magnetism from nearby appliances and geomagnetism might affect  
the color of the TV picture. Move the TV/VCR away from the appli-  
ances, the TV/VCR can repair itself automatically. If you want to  
repair immediately, unplug the TV/VCR power cord, then plug it in  
again 30 minutes or so later.  
.
CLOSED CAPTION PROBLEM  
My TV/VCR is showing captions  
that are misspelled.  
POSSIBLE REMEDY  
You are watching a live broadcast and spelling errors made by the  
closed captioning production company may pass through uncorrected.  
A prerecorded program will not show any misspelled words because  
of the normal time available for editing the captions.  
My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue  
in its entirety or there is a delay of are common for live broadcast. Most captioning production companies  
what is being said.  
can display a dialogue to a maximum of 220 words per minute. If a  
dialogue exceeds that rate, selective editing is used to insure that the  
captions remain up-to-date with the current TV screen dialogue.  
• Interference caused by building, power lines, thunderstorms, etc.  
may cause scrambled or incomplete captions to appear.  
My captions are scrambled with  
white boxes on the TV screen.  
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed  
as being closed captioned but none up the actual program so that additional advertising time can be  
of the captions were displayed.  
given. Since the decoder cannot read the compressed information,  
captions will be lost.  
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating  
show any captions. The tape box company accidentally left out the captioning signals during the  
mentions it being closed captioned. copying process.  
My TV screen shows a black box  
on certain channels.  
You are in the TEXT mode. Select CAPTION mode to CAPTION  
[OFF].  
- 26 -  
EN  
9I03  
 
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
CRT :  
13 or 19 inch in-line gun, 90˚  
deflection tube  
NTSC-M  
Video input level :  
Audio input level :  
0.5~2.0Vp-p  
-15dBs  
Television system :  
Closed caption system :§15.119/FCC  
Video S/N ratio : More than 46dB  
Audio S/N ratio : More than 43dB  
Video Heads :  
Tape width :  
Tape speed  
SP :  
LP :  
SLP :  
Tuner channel  
TV VHF Low :  
TV VHF High :  
TV UHF :  
CATV  
Rotary two-head  
1/2 inch  
OTHER SPECIFICATIONS  
[ 13 inch model ]  
Power requirement : AC 120V/60Hz  
Power consumption : 65W  
33.40mm/sec.  
16.67mm/sec.  
11.12mm/sec.  
Dimensions :  
H:15-3/8” (389mm)  
W:14-1/2” (367mm)  
D:14-7/8” (377mm)  
23.1 lbs (10.5kg)  
#2~#6  
#7~#13  
#14~#69  
Weight :  
[ 19 inch model ]  
Power requirement : AC 120V/60Hz  
Power consumption : 80W  
VHF :  
5A  
MID band :  
SUPER band :  
HYPER band :  
Terminals  
A5~A1, A~I  
J~W  
W+1~W+84  
Dimensions :  
19-1/2” (493mm)  
W:19-3/8” (491mm)  
D:18-3/4” (475mm)  
43.0 lbs (19.5kg)  
Weight :  
Antenna input :  
VHF/UHF 75 ohms  
unbalanced  
RCA connector [ 1  
RCA connector [ 1  
1/8” monaural (3.5 mm)  
Designs and specifications are subject to change  
without notice.  
If there is a discrepancy between languages, the  
default language will be English.  
Video input :  
Audio input :  
Earphone :  
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
TV Display  
31  
32  
33  
34  
35  
36  
CATV channel  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
TV Display  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
W+55 W+56 W+57 W+58  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
91  
92  
93  
94  
CATV channel  
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
TV Display  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
- 27 -  
EN  
9I03  
 
CONTROLES DE OPERACIÓN Y SUS FUNCIONES  
Este manual sirve para los modelos de 13" y 19". A excepción de la apariencia, la operación de los dos modelos es exac-  
tamente la misma. En este manual se muestra el modelo de 19".  
NOTA:  
No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un  
mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el  
número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del  
mando a distancia universal.  
VIDEO AUDIO  
POWER  
CHANNEL  
STOP/EJECT  
REW PLAY F.FWD  
REC/OTR EARPHONE  
VOLUME  
13  
1 2 3 4 5 6 7 8 9101112  
14  
5 Botones de canales (CHANNEL K/ L)–  
Púlselos para seleccionar los canales deseados  
para ver o grabar.  
25  
7
WAKE-UP  
/SLEEP  
POWER  
EJECT  
Se puede mostrar el menú principal en la pantalla  
del televisor pulsando repetidamente este botón del  
televisor/videograbadora.  
3
CHANNEL  
RETURN  
1
4
7
2
5
8
3
6
9
24  
Función de seguimiento– Pulse los botones  
para minimizar el ruido de vídeo (líneas o puntos  
en la pantalla) durante la reproducción.  
6 Ventanilla sensora del mando a distancia–  
Recibe las señales infrarrojas procedentes del  
mando a distancia.  
15  
CHANNEL  
VOLUME  
5
4
0
+100  
MENU  
DISPLAY  
MUTE  
16  
17  
8
7 Botón de parada (STOP)– Púlselo para deten-  
er la cinta.  
23  
9
PLAY  
Botón de expulsión (EJECT)–Púlselo en el  
modo de parada para expulsar la cinta del televi-  
sor/videograbadora.  
10  
REW  
F.FWD  
STOP  
7
SPEED PAUSE/STILL  
RECORD  
Botón L–  
22  
21  
11  
18  
T-PROG.  
CLEAR  
Púlselo para seleccionar los modos de ajuste  
desde el menúde la pantalla.  
GAME  
TIME SEARCH  
COUNTER  
RESET  
Púlselo para introducir dígitos cuando establezca  
19  
20  
un programa.  
(Por ejemplo: Para ajustar el reloj o establecer un  
programa de temporizador)  
8 Botón de rebobinado (REW)– Púlselo para  
rebobinar la cinta, o para ver la imagen en retro-  
ceso rápido durante el modo de reproducción.  
(Búsqueda con rebobinado)  
1 Toma de entrada de vídeo (VIDEO)–  
Conéctela a la toma de salida de vídeo de su  
videocámara u otra videograbadora.  
2 Toma de entrada de audio (AUDIO)–  
Conéctela a la toma de salida de audio de su  
equipo de audio, videocámara u otra  
videograbadora.  
Botón s–  
Púlselo para seleccionar un modo desde un menú-  
particular.  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
3 Botón de la alimentación (POWER)–  
Púlselo para encender y apagar el  
9 Botón de reproducción (PLAY)– Púlselo  
para iniciar la reproducción.  
Botón K–  
televisor/videograbadora. Púlselo para activar la  
grabación con temporizador.  
X
Y
)–  
4 Botones de volumen (VOLUME  
/
Ajustan el nivel del volumen.  
Púlselo para seleccionar los modos de ajuste  
- 28 -  
ES  
0I29  
 
ANT.  
26  
27  
desde el menúde la pantalla.  
Púlselo para introducir dígitos cuando establezca  
un programa.  
16 Botón de menú (MENU)– Púlselo para visu-  
alizar el menúprincipal en la pantalla del televi-  
sor.  
17 Botón del visualizador (DISPLAY)–  
Visualiza el contador o el número del canal actual  
y la hora actual en la pantalla del televisor.  
18 Botón de velocidad de cinta (SPEED)–  
Púlselo para elegir la velocidad de grabación  
deseada: SP/SLP.  
(Por ejemplo: Para ajustar el reloj o establecer un  
programa de temporizador)  
10 Botón de avance rápido (F.FWD)– Púlselo  
para avanzar rápidamente la cinta, o para ver la  
imagen en avance rápido durante el modo de  
reproducción. (Búsqueda con avance rápido)  
Botón B–  
19 Botón T-PROG. CLEAR– Púlselo para cance-  
lar un programa de temporizador.  
Cuando establezca un programa (por ejemplo:  
para ajustar el reloj o para establecer un progra-  
ma de temporizador), púlselo para determinar su  
elección y vaya al paso siguiente que quiera  
introducir.  
Púlselo para determinar los modos de ajuste  
desde el menúde la pantalla.  
Púlselo para seleccionar un modo desde un  
menúparticular.  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
Botón de reposición del contador  
(COUNTER RESET)– Púlselo para reponer el  
contador a 0:00:00.  
20 Botón de juego (GAME)– Establece el modo  
del juego y el modo de entrada externa al mismo  
tiempo.  
21 Botón de búsqueda con tiempo (TIME  
SEARCH)– Púlselo para activar el modo de  
búsqueda con tiempo.  
22 Botón de pausa/imagen fija  
11 Botón de grabación (REC)– Púlselo para ini-  
ciar la grabación manual.  
(PAUSE/STILL)– Púlselo para detener temporal-  
mente la cinta durante la grabación o para ver  
una imagen fija durante la reproducción.  
23 Botón de silenciamiento (MUTE)– Silencia  
el sonido. Púlselo de nuevo para recuperar el  
sonido.  
Botón de grabación de un toque (OTR)–  
Activa la grabación de un toque. (Sólo en el tele-  
visor/videograbadora)  
12 Indicador de grabación (RECORD)–  
Parpadea durante la grabación.  
24 Botón de retorno de canal (CHANNEL  
RETURN)– Púlselo para volver al canal anterior.  
Por ejemplo, pulsando una vez este botón, la  
visualización del canal cambiará de 3 (canal actu-  
al) a 10 (canal anterior), y al pulsarlo por segunda  
vez, el canal cambiará del 10 al 3.  
25 Botón del temporizador despertador/para  
dormir (WAKE UP/SLEEP)– Ajusta el tempo-  
rizador para despertarse/dormir.  
26 Cordón de alimentación– Conéctelo a la  
toma de CA estándar (120V/60Hz).  
27 Terminal de antena (ANT.)– Para conectar  
una antena o sistema de televisión por cable.  
Se enciende en el modo de espera de la grabación  
con temporizador.  
13 Toma de auriculares (EARPHONE)– Para  
conectar los auriculares (no suministrados) y  
escuchar en privado. La toma es mono y tiene un  
tamaño de 3,5 mm.  
14 Compartimiento del videocasete  
15 Botones numerados– Púlselos para selec-  
cionar los canales deseados para ver o grabar.  
Para seleccionar canales del 1 al 9, pulse primero  
el botón 0 y luego el botón 1 a 9.  
Botón +100– Cuando seleccione canales de  
televisión por cable cuyo número sea superior al  
99, pulse primero este botón, y luego pulse los  
dos últimos dígitos. (Para seleccionar el canal  
125, pulse primero el botón “+100” y luego el  
“2” y el “5”.)  
- 29 -  
ES  
0I29  
 
CONEXIONES DE ANTENA/CABLE  
Desde el cable coaxil o  
caja de emisiones vía  
satélite de 75 ohm del  
sistema de Cable  
Caja de CATV  
o caja de emi-  
siones vía satélite  
(no incluído)  
Antena combinada de  
VHF/UHF  
(no incluído)  
Antena de varilla UHF/VHF  
(incluído para solamente 13”)  
OUT  
IN  
Antena VHF  
(no incluído)  
Desde el  
sistema de Cable  
Antena UHF  
(no incluído)  
o
ANT.  
Combinador de  
VHF/UHF  
(no incluído)  
o
o
ANT.  
o
Cable coaxil  
de 75 ohm (no incluído)  
Cable bifilar plano  
televisor/videograbadora. La grabación inatendida se  
limita a un canal cada vez.  
PARA GRABAR UN CANAL  
CODIFICADO/DESCODIFICADO  
1. Ajuste el selector de canales del  
televisor/videograbadora al canal de salida del con-  
vertidor de televisión por cable o del convertidor de  
emisiones vía satélite. (Ej.: CA3)  
2. Seleccione el canal que desee grabar de su conver-  
tidor de televisión por cable o del convertidor de emi-  
siones vía satélite.  
ANTENA COMBINADA DE VHF/UHF  
La antena de varilla de VHF/UHF (incluído para sola-  
mente 13”) es desmontable. Inserte el vástago de la  
antena en el agujero de la parte trasera superior del tele-  
visor/videograbadora.  
Conecte la varilla de antena de VHF/UHF o la antena  
combinada de VHF/UHF al terminal ANT. del televi-  
sor/videograbadora.  
ANTENAS SEPARADAS DE VHF/UHF  
En algunos lugares será necesario utilizar una antena  
exterior.  
CABLE SIN CONVERTIDOR/DESCODIFICADOR  
Utilice esta conexión si su sistema de televisión por  
cable se conecta directamente a su  
televisor/videograbadora sin convertidor.Utilizando esta  
conexión usted podrá:  
1)Utilizar el mando a distancia del  
televisor/videograbadora para seleccionar canales.  
2)Programar uno o más canales sin codificar para  
realizar la grabación automática con temporizador.  
NOTA: Con esta unidad SÓLO se podrá grabar y ver  
un mismo canal al mismo tiempo.  
MODO DE ENTRADA EXTERNA  
Cuando utilice una señal de entrada externa (otra  
videograbadora o una videocámara), conecte los cables  
de salida de audio/vídeo del equipo de reproducción a  
las tomas AUDIO IN/VIDEO IN de su  
televisor/videograbadora. Y luego pulse el botón  
CHANNEL K o L hasta que “AUX” aparezca en la  
pantalla.  
Usted puede programar el temporizador para que  
explore todos los canales que puedan recibirse en su  
zona.  
CABLE CON CONVERTIDOR/DESCODIFICADOR  
O CONVERTIDOR DE EMISIONES VÍA SATÉLITE  
INSTALACIÓN DE LAS PILAS  
Si su servicio de televisión por cable le suministra un  
convertidor, o si usted utiliza un sistema de emisiones  
vía satélite, usted podrá utilizar las conexiones básicas  
mostradas aquí.  
1)Abra la tapa del compartimiento de las pilas del  
mando a distancia presionándola en el sentido de la  
flecha.  
Utilizando estas conexiones, usted también podrá  
grabar canales codificados. Sin embargo, la selección  
de los canales deberá hacerse con el convertidor de tele-  
visión por cable con el convertidor de emisiones vía  
satélite. Esto significa que los canales no podrán ser  
cambiados con el mando a distancia del  
2)Inserte 2 pilas tamaño “AA” en el compartimiento de  
las pilas, en el sentido indicado por las marcas de  
polaridad (+/-).  
3)Vuelva a poner la tapa.  
- 30 -  
ES  
0I29  
 
PREPARACIÓN DE CANALES POR  
PRIMERA VEZ  
1)Enchufe el cable de alimentación del  
televisor/videograbadora en una toma de CA están-  
dar.  
NOTA: Si aparezcan algunos digitos en el rincón de  
la pantalla, pulse el botón POWER sin desenchufar el  
cable de alimentación.  
2)Pulse el botón POWER para encender el televi-  
sor/videograbadora.  
3)Seleccione “ENGLISH” o “ESPAÑOL” utilizando  
el botón F.FWD/B o REW/s. “[ ]” indica el  
idioma seleccionado.  
4)Pulse el botón PLAY/K o STOP/L para señalar  
“AUTOPRESELECCION”.  
AJUSTE DEL RELOJ  
Cerciórese...  
La alimentación del televisor/videograbadora  
deberá estar conectada.  
En el ejemplo de abajo, el reloj va a ajustarse así:  
FECHA: 6 de mayo de 2003  
HORA: 5:40 PM  
1)Pulse el botón MENU en el mando a distancia.  
Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE RELOJ”.  
Luego, pulse el botón F.FWD/B.  
2)Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE MANUAL RELOJ”.  
Luego, pulse el botón F.FWD/B.  
3)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el mes deseado. (Ejemplo: Mayo - 05)  
Luego, pulse el botón F.FWD/B.  
Luego pulse el botón F.FWD/B. El sintonizador  
explorará y memorizará todos los canales activos  
de su área.  
NOTAS:  
4)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el día del mes deseado. (Ejemplo: 6 - 06)  
Luego, pulse el botón F.FWD/B.  
5)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el año deseado. (Ejemplo: 2003)  
Luego, pulse el botón F.FWD/B.  
6)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca la hora deseada. (Ejemplo: 5, PM)  
Luego, pulse el botón F.FWD/B.  
7)Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el minuto deseado. (Ejemplo: 40)  
8)Pulse el botón MENU en el mando a distancia.  
Aunque los segundos no se visualizan, éstos  
empiezan a contar desde 00 cuando se pulsa  
MENU en el mando a distancia. Utilice esta fun-  
ción para sincronizar el reloj con la hora correcta.  
El televisor/videograbadora distingue entre los  
canales de televisión estándar y los canales de tele-  
visor por cable.  
Si desea reproducir o grabar una cinta ANTES de  
preajustar el sintonizador, usted tendrá que pulsar  
el botón MENU en el mando a distancia. Para  
preajustar de nuevo el sintonizador, consulte  
“REPETICIÓN DE LA PREPARACIÓN DE  
CANALES”.  
La unidad de televisor/videograbadora puede  
reconocer los canales de TV como ellos de TV por  
cable a causa de los condiciones de recepción. En  
este caso, pruebe el preajuste automático de nuevo  
en los condiciones finas de recepción.  
5)El sintonizador se para en el canal memorizado  
más bajo. Si desea recuperar canales selecciona-  
dos, usted podrá seleccionar directamente el canal  
deseado con los botones numerados del mando a  
distancia o con los botones CHANNEL K o L.  
- 31 -  
ES  
 
LIMITED WARRANTY  
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials  
or workmanship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from  
the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded  
from this warranty.  
LABOR:  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date  
of original retail purchase.  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR  
OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO  
OBTAIN SERVICE UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty  
does not apply to any product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product  
not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplica-  
tion, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FIT-  
NESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTA-  
TIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED  
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHO-  
RIZED SERVICE FACILITY.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT  
FUNAI CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITH-  
OUT PRIOR NOTICE.  
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,  
please call 1-800-968-3429 or write to the following:  
FUNAI CORPORATION  
Customer Service  
100 North Street; Teterboro, NJ 07608  
Tel :1-800-968-3429  
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.  
Printed in Malaysia  
0EMN02092  
Download from Www.Somanuals.com. All Manuals Search And DoTw5nl4o0ad1.UB / T7401UB * * * * *  

Sharp Headphones HT X1W User Manual
Sierra Products Stove EF5001U User Manual
Sony Camera Flash HVL FDH3 User Manual
Sony Cassette Player WM FX161 User Manual
Sony Home Theater System CMTDH3 User Manual
Sony VCR SLV SX10EG User Manual
Speco Technologies Home Security System HTINT650S User Manual
Speed Queen Washer Dryer CL8761 User Manual
Stiga Lawn Mower 12 9234 73 User Manual
Sylvania Clock Radio SIP3019 User Manual