'9'ꢀꢁꢂꢂ
In-Dash Single Disc
DVD/CD Player
Before operating the unit, please read these
instructions carefully
128-5987
Operating Instructions
•
•
Depending on reception quality of the TV, noise interference may appear while a
broadcast is being received with the DVD powered on. This is not a malfunction of the
DVD or the TV. To watch a TV broadcast, turn off the DVD.
To prevent an operational malfunction, do not play discs other than DVD audio discs,
DVD-ROMs, CD-ROMs, Photo CDs and DVDs with region numbers other than this
player’s region number.
•
•
Only use the correct size of fasteners or cable connectors during installation. Failure to
comply with this requirement may create a fire hazard.
Kindly refer to an authorized dealer if in doubt concerning any of the preceding items.
When installing this unit together with a display monitor, please check that this
configuration complies with your local traffic rules and regulations
This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision
Corporation, and is intended for limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
3
128-5987
Operating Instructions
INSTALLATION GUIDE
Precautions:
1. This DVD/CD player should be install by qualified technician or service
personnel.
2. The DVD/CD is designed to operate with a 12 Vdc, negative ground battery
system.
3. Disconnect the ground wire from the battery terminal before connecting the
unit to the electrical system.
4. The wiring from other units or accessories might display a similar color code
to this product; however, they may not perform the same function. It is always
advisable to refer to the electrical connection diagrams of a unit or its
accessories before installation to avoid incorrect connections.
5. Use proper insulation and fastening materials to prevent electrical short-
circuiting.
6. Do not connect the yellow wire of the DVD/CD player directly to the battery
terminal. Remember to connect the red wire to the ACC side of the ignition
switch. Failure to do so may result in prematurely draining the battery charge.
7. Use only supplied accessories to avoid damaging the unit during installation.
8. Do not install the DVD/CD player at an incline angle exceeding 30°.
9. Do not install the DVD/CD player at a position that may cause injuries to the
passenger(s) during an accident.
4
128-5987
Operating Instructions
Back Panel
The figure below shows the back panel design for the player. It also indicates the wire
definition for interconnections.
Control Unit
Interface
Yellow : BATT
Red
Blue
Black : GND
: ACC
: SIDEBRAKE
Audio Output
Red : Audio R
White : Audio L
Yellow
: Video Output
Optical Connector
3 pin Con : Rear IR
5
128-5987
Operating Instructions
2.1 Remote Control Reference Guide
1. Power Button
2. Setup Button
3. Display Button
4. Up Cursor Key
5. Left Cursor Key
6. Enter Key
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
Mute Button
Title Button
Menu/PBC Button
Return Button
Right Cursor Key
Slow Button
Next/Forward Skip Button
Stop Button
Forward Scan Button
Audio Select Button
Angle Select Button
Search Button
7. Previous/Reverse Skip Button
8.
Down Cursor Key
9. Reverse Scan Button
10. Play/Pause Button
11. Subtitle On/Off Button
12. Subtitle Selection Button
13 Numeric Buttons
Repeat Button
14. Eject Button
6
128-5987
Operating Instructions
2.2 Front Panel Control Reference Guide
1
2
3
4
ꢀ
SENSOR
RETURN
STOP
PAUSE
FF
PLAY
SEL
MUTE
AUDIO
FR
MENU
TITLE
OFF
VIDEO
20
19
18 17 16 15 14 13 12 11
10 9
8
7
6
5
1. Power Indicator
2. Disc slot
3. Remote Sensor
4. Eject Button
5. Cursor Right Key
6. Cursor Up Key
7. Enter Key
8. Cursor Down Key
9. Cursor Left Key
10. Play Button
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
TITLE Button
MENU Button
Pause Button
Forward Skip Button
Backward Skip Button
Stop Button
Audio Button
Mute Button
Return Button
Power On/Off Button
7
128-5987
Operating Instructions
3. Basic Functions
3.1 DVD Playback (DVD)
1) Press the POWER( ) button on the remote control, or the DVD/CD player front panel POWER
) button to switch on unit power.
(
2) Insert a disc into the unit.
3) DVD playback commences:
•
•
The disc will start to play if the disc does not have any menu recorded on it.
If the disc has one or more titles recorded on it, a menu screen will appear on the TV monitor.
NOTE: When “INVALID” appears, it means that the corresponding operation is prohibited either by
the player or by the disc.
The DVD will display “INVALD DISC” if the DVD disc has a region code that does not compare
favorably with the unit.
TITLE MENU
4) Press the
/
/
/
buttons to select the preferred title.
1. Fish
2. Bird
3. Dog
5) Press the ENTER button: the selected item will now start playing.
6) Press the MENU or TITLE button; the menu screen will appear.
After operation, press POWER ( ) button to place the unit in standby mode.
3.2 Audio CD or Video CD Playback (CD/VCD)
1) Press the POWER ( ) button on the remote control, or the DVD/CD player front panel POWER
(
) button to switch on unit power.
2) Insert a disc into the unit.
3) Press the PLAY/PAUSE ( ) button to start playback of the disc.
1. Dog
2. Cat
3. Sheep
4. Cow
5. Bird
3.2.1 Playback Video CDs with Playback Control
Using Menus
•
•
This function operates only with a Video CD having playback
control (Version 2.0).
Perform steps 1 to 3 as outlined in paragraph 3.2; the menu will be displayed
on the TV monitor.
4) Press the numeric buttons to select the preferred track.
5) Press the RETURN button to stop the playback and return to the Menu screen.
NOTE: The play details in the menu will vary depending on the disc in question.
The basic operations to play Video CD having PBC (Playback Control) consist of the following:
•
•
•
NEXT TRK
PREV TRK
RETURN- To return to the previous menu.
- To go to the next menu (if available) or next track.
- To go to the previous menu (if available) or previous track.
8
128-5987
Operating Instructions
3.2.2 Playback Video CDs with Playback Control
Without Using Menus (VCD)
1) Press the MENU/PBC button to set PCB off.
2) “PBC OFF” will be displayed on the TV screen.
3) Press the required track number button to select the preferred track, or press the
PLAY/PAUSE ( ) button to commence playback.
To return to menu playback:
1) Press the MENU/PBC button: “PBC ON” will be displayed on the TV screen.
2) The menu (if available) will be displayed on the TV monitor.
3.3 Fast Forward or Reverse (CD/VCD/DVD)
1) Press the F.FWD ( ) button during playback.
Each time this button is pressed, the unit will go into a rapid advance playback mode.
The following OSD will be shown on the TV screen, depending on the speed of the
playback selected:
Audio CD Playback
FAST FW
PLAY
Video CD/DVD Playback
FAST FWX2
FAST FWX4
FAST FWX32
FAST FWX8
FAST FWX16
PLAY
2) Press the F.REV ( ) button during playback.
Each time this button is pressed, the unit will go into a rapid reverse playback mode.
The following OSD will be shown on the TV screen, depending on the speed of the
playback selected:
CD Playback
FAST BW
PLAY
VCD/DVD Playback
FAST BWX2
PLAY
FAST BWX4
FAST BWX8
FAST BWX16
FAST BWX32
9
128-5987
Operating Instructions
3.4 Next track or previous track (CD/VCD/DVD)
Press
during playback.
Audio CD and Video CD:
The player will skip forward to the next track each time the button is pressed.
“SKIP FW” will be displayed on the TV screen.
DVD:
The player will skip forward to the next title/chapter each time the button is pressed.
“SKIP FW” will be displayed on the TV screen.
Press
during playback.
Audio CD and Video CD:
The player will skip to the beginning of the current track each time the button is pressed.
The player will skip to the beginning of the previous track when the button is pressed twice
consecutively.
“SKIP BW” will be displayed on the TV screen.
DVD:
The player will skip to the beginning of the current chapter each time the button is pressed.
The player will skip to the beginning of the previous chapter when the button is pressed twice
consecutively.
“SKIP BW” will be displayed on the TV screen.
3.5 Play / Pause (CD/VCD/DVD)
Press the PLAY/PAUSE ( ) button during playback; the player will be placed in the pause mode.
Press the PLAY/PAUSE ( ) button again; the player will return to normal playback
3.6 Slow Motion play (VCD/DVD)
Each time the SLOW button is pressed, the unit will go into a slow motion playback mode.
The following OSD will be shown on the TV screen:
SLOW FWX2
SLOW FWX4
SLOW FWX8
SLOW FWX16
PLAY
3.7 Stop (CD/VCD/DVD)
1) During Audio CD playback, when the STOP ( ) button is pressed, the CD playback will stop.
2
During VCD/DVD playback, when the STOP ( ) button is pressed, “PRE STOP” will appear.
The player records the point where the STOP ( ) button is pressed (Resume playback function).
3) Press the PLAY/PAUSE ( ) button again and play will resume from this point.
During “PRE STOP”, if the STOP ( ) button is pressed, “STOP” will appear and the resume
playback function will be cleared.
NOTE: The resume playback function is not available for Audio CDs.
10
128-5987
Operating Instructions
3.8 Search Function (CD/VCD/DVD)
The Search function enables you to pinpoint a specific location by entering the time/track/chapter or
title.
Audio CD:
When the SEARCH button is pressed the following will be displayed:
TRACK xx
TIME xx:xx
CD
Use the numeric keys to enter the desired track or disc time; pressing the ENTER button will cause the
player to start playing at the selected track or time.
If you are not in search mode, you may use the numeric keys to enter the desired track; the player will
commence at the selected track.
Video CD:
When SEARCH button is pressed the following will be displayed:
TRACK xx
TIME xx: xx:xx
No display
Use the numeric keys to enter the desired track or disc time; pressing the ENTER button will cause the
player to start playing at the selected track or time.
If you are not in search mode, you may use the numeric keys to enter the desired track; the player will
commence at the selected track.
NOTE: The search function is not available during Video CD “PBC ON”.
11
128-5987
Operating Instructions
DVD:
When the SEARCH button is pressed the following will be displayed:
TITLE xx
CHAPTER xxx
TIME xx:xx:xx
No display
Use the numeric keys to enter the desired title or chapter, or chapter time; pressing the ENTER button
will cause the player to start playing at the selected title, chapter or chapter time.
If you are not in search mode, you may use the numeric keys to enter the desired chapter; the player
will commence at the selected chapter.
3.9 Advanced Playback (CD/VCD/DVD)
3.9.1 Repeat Mode
When the REPEAT button is pressed, the player will toggle between different repeat modes (Audio
CD/ Video CD)
When the REPEAT button is pressed:
REPEAT ONE
REPEAT ALL
REPEAT OFF
REPEAT ONE
REPEAT ALL
REPEAT OFF
=
=
=
The current track will be repeated.
The current disc will be repeated.
Repeat mode will be switched off.
NOTE: The REPEAT function is not available during Video CD “PBC ON”.
12
128-5987
Operating Instructions
For DVD:
When the REPEAT button is pressed:
RPT CHAPT
RPT TITLE
REPEAT OFF
RPT CHAPT
RPT TITLE
REPEAT OFF
=
=
=
The current chapter will be repeated
The current title will be repeated
Repeat mode will be switched off
3.9.2 Camera Angle (DVD)
Some DVD discs may contain scenes which have more than one viewing angle.
For these discs, the same scene can be viewed from a different angle by using the ANGLE button as
follows:
NOTE: This function will only operate on discs where different camera angles have been
recorded.
1) During DVD playback, press the ANGLE button.
“ANGLE x/y” will appear, where x represents the current camera angle, and y represents the
total available camera angle.
2) Press the ANGLE button until the preferred angle is selected.
The ANGLE selection will cycle through all available camera angles.
3.9.3 Audio Function (VCD/DVD)
The audio function operates only for discs that have multiple audio soundtracks.
During VCD playback, press the AUDIO button until the desired audio is selected.
AUDIO STEREO
AUDIO LL
AUDIO RR
During DVD playback, press the AUDIO button.
“AUDIO x/y” will appear, where x represents the current audio stream and y represents the
total available audio streams.
Press the AUDIO button until the preferred audio is selected.
The audio selection will cycle through all available audio streams.
13
128-5987
Operating Instructions
3.9.4 Subtitle (DVD)
During DVD playback, you may change the subtitle language from the one selected at the initial setting
to a different language, if available.
1) When the SUBTITLE ON/OFF button is pressed:
SUBTITLE ON
SUBTITLE OFF
2) During DVD playback with SUBTITLE ON, press the SUBTITLE button .
“SUBTITLE x/y” will appear, where x represents the current subtitle and y represents the
total available subtitle.
Press the SUBTITLE button until the preferred subtitle is selected.
The SUBTITLE selection will cycle through all available subtitles.
NOTE: 1. The SUBTITLE works only for discs that have multiple subtitles.
2. In some cases, the subtitle is not changed immediately to the one selected.
3.9.5 DVD Menu (DVD)
Most DVD discs have unique menu structures call DVD menus.
The DVD menu contents and operation may differ from disc-to-disc.
1) During DVD playback, press the MENU button.
The DVD menu available on the disc will be displayed.
2) Use the
/
/
/
buttons to select the preferred item, or use the numeric buttons(s) to
make a selection.
3) Press the ENTER button; the selected item will start playing.
3.9.6 Title Menu (DVD)
Some DVD discs may contain more than one title. If the disc has a title menu recorded on it, the
TITLE button can be used to access it.
1) During DVD playback, press the TITLE button.
A list of the titles may be displayed.
2) Use the
/
/
/
buttons to select the preferred item.
3) Press the ENTER button; the selected title will start playing.
14
128-5987
Operating Instructions
3.9.7 Display Function (CD/VCD/DVD)
The display function enables you to view the status, current title number, track number and the total
playing time of the disc on the TV screen.
Audio CD:
When the DISPLAY key is pressed, the following OSD will be shown:
TRACK
TTIME
1/15
01:41
TRACK
TRTIME
1/15
02:30
TRACK
DTIME
1/15
11:37
TRACK
DRTIME
1/15
58:50
No display
TTIME
= Track time
TRTIME
DTIME
= Track remaining time
= Disc time
DRTIME
= Disc remaining time
Video CD:
When the display key is pressed, the following OSD will be shown:
TRACK
1/15
TRACK
1/15
TRACK
DTIME
1/15
00:11:37
TTIME 00:01:41
TRTIME 00:02:30
TRACK
1/15
DRTIME 00:58:50
No display
TTIME
= Track time
TRTIME
DTIME
DRTIME
= Track remaining time
= Disc time
= Disc remaining time
15
128-5987
Operating Instructions
DVD:
When the display key is pressed, the following OSD will be shown:
TITLE
CHAPTER
CTIME
ANGLE
SUBTITLE
AUDIO
1/8
1/20
02:14:21
1/3
TITLE
CHAPTER
CRIME
ANGLE
SUBTITLE
AUDIO
1/8
TITLE
CHAPTER
TTIME 020:14:21
ANGLE
SUBTITLE
AUDIO
1/8
1/20
1/20
02:14:21
1/3
1/3
2/3
1/3
2/3
1/3
2/3
1/3
TITLE
CHAPTER
1/8
1/20
TRTIME 21:14:21
ANGLE
SUBTITLE
AUDIO
1/3
2/3
1/3
No display
CTIME
CRTIME
TTIME
= Chapter time
= Chapter remaining time
= Title time
TRTIME
= Title remaining time
3.9.8 Setup Menu (DVD)
When the player is in stop mode, pressing the SETUP button will allow you to modify some of the
player’s basic settings.
1) During STOP, press the SETUP button, the setup menu will appear as follows:
SETUP
(1) DISC LANGUAGE
(2) PASSWORD
(3) PARENTAL
(4) TV ASPECT
(5) DIGITAL OUT
2) Use
/
or numeric key to select the desired item, then press the ENTER button:
3) To exit, press the SETUP button.
16
128-5987
Operating Instructions
(1) Disc Language
a) During STOP, press the SETUP button; the setup menu will appear.
b) Use the buttons or numeric key to select the DISC LANGUAGE item; then
/
press the ENTER button.
The disc language menu will appear as follows:
DISC LANGUAGE
(1) AUDIO
(2) SUBTITLE
(3) MENU
c) Use the
/
buttons or numeric key to select AUDIO/SUBTITLE/MENU, then press
the ENTER button.
If audio is selected, the following menu will appear:
AUDIO
(1) DEFAULT
(2) CHINESE
(3) ENGLISH
(4) JAPANESE
(5) FRENCH
(6) GERMAN
d) Use the
/
buttons or numeric key to select the preferred language for
AUDIO/SUBTITLE/MENU, then press the ENTER button.
e) Use the RETURN button to return to the previous menu, or press the SETUP button to
exit.
17
128-5987
Operating Instructions
(2) Password
NOTE: The factory default password is 1234
a) During STOP, press the SETUP button, the setup menu will appear.
b) Use the buttons or numeric key to select the PASSWORD item, then press the
/
ENTER button. The change password menu will appear.
CHANGE PASSWORD
PARENTAL
PASSWORD
c) Use the numeric keys to enter the password; then press ENTER.
d) If the correct password is entered, the user can now enter the new password.
CHANGE PASSWORD
NEW
PASSWORD
If the incorrect password is entered, the previous menu will be shown.
e) Use the numeric keys to enter the new password; then press ENTER.
f) The user is required to confirm the new password as shown.
CHANGE PASSWORD
CONFIRM
PASSWORD
g) If the new password and the confirm password agree, the SETUP menu will be shown
again.
18
128-5987
Operating Instructions
(3) Parental Control
a) During STOP, press the SETUP button, the setup menu will appear.
b) Use the buttons or numeric key to select the PARENTAL item; then press ENTER.
/
The DVD/CD player will request a parental password.
PARENTAL PASSWORD
PASSWORD
c) Use the numeric keys to enter the password; then press ENTER.
d) If the correct password is entered, the parental control menu will be shown as follows:
PARENTAL CONTROL
(8) KIDS ONLY
(7)
(6)
(5)
(4) NO ADULT
(3)
(2)
(1)
(0) VIEW ALL
If an incorrect password is entered, “INVALID” will be appear.
e) Use the
/
buttons or numeric key to select the desired parental control; then press
ENTER.
f) The SETUP menu will be shown again.
(4) TV Aspect
a) During STOP, press SETUP button, the setup menu will appear.
b) Use the buttons or numeric key to select the TV ASPECT; then press ENTER.
/
The preferred TV aspect menu will be shown as follows:
TV ASPECT
(1) 4:3 PAN SCAN
(2) 4:3 LETTERBOX
(3) 16:9 WIDE
c) Use the
ENTER.
d) The SETUP menu will be shown.
/
buttons or numeric key to select the preferred TV ASPECT item; then press
19
128-5987
Operating Instructions
(5) Digital Out
a) During STOP, press SETUP button, the setup menu will appear.
b) Use the
/
buttons or numeric key to select the DIGITAL OUT item, then press
ENTER.
The preferred digital audio output will be shown as follows:
DIGITAL AUDIO OUT
(1) LPCM
(2) DOLBY DIGITAL
(3) MPEG
c) Use the
/
buttons or numeric key to select the preferred digital audio output, then
press ENTER.
d) The SETUP menu will be shown.
20
128-5987
Operating Instructions
4. Product Specification
GENERAL
Power Supply
: 12VDC Typical
Current Consumption
Operating Positions
Dimension (WxHxD)
Inches (Millimeters)
Weight
: Less than 3.0 A
: Horizontal mount only
: 7 (178) x 2 (50) x 7.4 (190)
: 2.0 kg
AUDIO
Output
Frequency Response
Distortion
: 700mV rms, 600Ω
: 20 Hz to 20 kHz (CD audio / 44.1kHz sampling)
: 0.02% (at 1 kHz)
Dynamic Range
: Above 85dB
S/N Ratio
Cross Talk
: ≥ 90dB
: -75dB
Optical Output
: Connection to DSP unit for 5.1 channel Dolby
Digital & dts sound reproduction
VIDEO
Television System
Playback Disc
: NTSC/PAL
: DVD/VCD/CD & CD-R compatible (12cm, 8cm)
Single-sided and dual layer DVD supported
Aspect Ratio
TV Encoder Resolution
Video S/N
: 4:3, 16:9
: 10 bit DAC
: 65 dB
CONNECTORS
Output
Audio Video Output
Digital Audio Output
: 3 RCA connectors for Video and Audio
: 1 optical transmitter
Input
Power Connector
: For external power supply input and Sidebrake
Consists of BATT, ACC, GND
Rear IR Connector
: For connection to a rear IR sensor
Interface
Controller Interface Connector
: For connecting to a control unit
21
128-5987
Operating Instructions
5. Region Management Information
This DVD/CD player is designed and manufactured to respond to the Region Management
Information that is recorded on a DVD disc. If the Region number described on the DVD disc
does not correspond to the Region number of this player, this player will not be able to play
the DVD disc.
This DVD/CD player is set to work only in a particular world region as labeled on the player.
Region Number
Country Within the Region
1
2
3
4
Canada, U.S, U.S Territories
Japan, Europe, South Africa, Middle East (including Egypt)
Southeast Asia, East Asia (including Hong Kong)
Australia, New Zealand, Pacific Islands, Central America, Mexico,
South America, Caribbean
5
6
Former Soviet Union, Indian Subcontinent, Africa (also North Korea,
Mongolia)
China
22
128-5987
|