AM/FM Stereo Clock Radio
with Dual Alarms
and Compact Disc Player
OWNER'S MANUAL
CKD2300
CKD2300_060305.p65
28
3/6/2005, 11:04
Thank you… … … … … … …
for purchasing this Emerson Dual Alarm Stereo Clock Radio with CD Player. This
compact sized unit has been designed to fit comfortably on any desk or bedside
table.
The CD Player has a 20-track programmable memory plus one-track/all tracks
automatic repeat playback. The clock radio features a bright, easily readable, 0.6”
red LED display that is visible from anywhere in the room. The dual alarms can be
set and used independently. You can set either or both alarms to wake you to an
electronic buzzer tone, your favorite radio station, or your favorite CD. And of course
there’s a battery back up system that will maintain the time and alarm settings in
the event of a temporary power interruption
This system was designed to give you many years of enjoyment with an absolute
minimum of care and maintenance. Please read this Owner’s Manual carefully and
completely to ensure that you get the maximum benefit from all the outstanding
features we have included in this product. If you encounter any problem with the
set up or operation of this model please do not return it to the retail store. Please
call the Emerson Customer Service Hotline toll free at 1-800-898-9020. One of
our service technicians will try to diagnose the problem for you.
Once again thanks for choosing this Emerson audio product.
2
CKD2300_060305.p65
2
3/6/2005, 11:04
IMPORTANT NOTES
• Avoid installing this unit in places • Operate controls and switches as
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much
heat, places lacking ventilation or
dusty areas, places subject to constant
vibration and/or humid or moist areas.
described in the manual.
• Before turning ‘On’ the power, make
certain that the power cord is properly
installed. When moving the set, be
sure to first disconnect the power cord.
• Store your CDs, in a cool area to avoid
damage from heat.
CLASS 1 LASER PRODUCT
CAUTION
CLASS 1 LASER PRODUCT
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
AVOID EXPOSURE TO BEAM
This product contains a low power Laser Device.
FCC Information
This equipment has been tested and found to comply with the limits for a class B
digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequencyenergy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
3
CKD2300_060305.p65
3
3/6/2005, 11:04
PREPARATION FOR USE
Unpacking and Set Up
• Carefully remove the unit from the display carton. Remove all the packing material
from the unit and remove any small strips of tape that may have been used to
prevent the CD door from opening in transit.
• Unwind the AC power cord and extend it to its full length.
• Unwind the FM antenna wire and extend it to its full length.
• This unit was shipped with a dummy CD transit card in the CD player. This
dummy CD prevents the laser pick up from moving during shipment. This card
must be removed before you can insert your own CDs. Open the CD door,
remove the transit card and discard it.
• Place the unit on a flat, level surface such as a table, desk, counter, shelf, etc,
convenient to a 120V 60 Hz AC outlet, out of direct sunlight, and away from
sources of excess heat, dust, moisture, or strong magnet fields.
Battery Back Up System
This model includes a battery back up circuit that will maintain the clock and alarm
settings in the event of a temporary power interruption. The battery back up system
requires one 9-Volt battery, not included. The battery compartment is located on
the bottom of the cabinet.
1.) Press the battery door-locking tab in the direction of the arrow and remove the
battery door.
4
CKD2300_060305.p65
4
3/6/2005, 11:04
2.) Connect a fresh 9-Volt alkaline battery to the battery terminal in the battery
compartment. It can only be connected one way.
3.) Replace the battery door.
If the power is interrupted the display will go ‘Off’ and the radio will not work. However
the battery will maintain the clock and alarm settings in memory. When the power
is restored the display will come on again and the clock and alarm settings will be
correct.
The life of the back up battery will depend on the frequency and length of the
power interruptions that you experience.
For best results we suggest you install a fresh battery every 9 to 12 months. Always
use a well-known brand of alkaline battery.
5
CKD2300_060305.p65
5
3/6/2005, 11:04
Power Source
This radio is designed to operate on 120V 60Hz AC only. Attempting to operate
this radio on any other power source could cause damage to the unit and such
damage is not covered by your warranty.
Make sure the radio is connected to an AC outlet that is always “live”. Do not
connect the radio to an outlet that is controlled by a wall switch.
Note: The system has polarized AC plug with one wide blade and one narrow
blade. The plug will only fit into matching polarized AC outlets.
This is a safety feature to reduce the possibility of electric shock. If the plug will not
fit in yourAC outlet, you probably have an outdated non-polarized outlet. You should
have your outdated outlet changed by a qualified, licensed electrician.
Do not file the wide blade on the plug, or
use an adapter to make the plug fit into
your outlet. This defeats the safety
feature and could expose you to electric
shock.
AC Outlet
AC Plug
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
6
CKD2300_060305.p65
6
3/6/2005, 11:04
LOCATION OF CONTROLS AND INDICATORS
Front Panel
11
10
9
12
8
7
13
14
15
16
17
18
22 23
21
24 25 26
6
5
4
3
2
19
1
1
20
1.) Speakers.
14.) SLEEP Button.
2.) POWER ‘On/Off’ Button.
3.) STOP Button.
15.) CD DISPLAY Button.
16.) PROGRAM Button.
17.) CLOCK SET Button.
4.) PLAY/PAUSE Button.
5.) REPEAT Button.
6.) RANDOM Button.
7.) AL 1 ‘On’ Indicator.
8.) PM Indicator.
18.)
19.)
SKIP/SEARCH-HOUR Button.
SKIP/SEARCH-MIN. Button.
20.) Tuning Dial pointer.
21.) SLEEP Indicator.
9.) CD compartment.
22.) POWER ‘On’ Indicator.
23.) REPEAT Indicator.
24.) PROGRAM Indicator.
25.) RANDOM Indicator.
26.) FM ST. Indicator.
10.) CDDoor OPEN/CLOSE Area.
11.) SNOOZE Button.
12.) LED Display.
13.) AL 2 ‘On’ Indicator.
7
CKD2300_060305.p65
7
3/6/2005, 11:04
Left Side Panel
Right Side Panel
30
29
31
32
28
27
35
33
34
27.) VOL. (Volume) Control.
28.) ALARM 2 (SET-ON-OFF) Selector Switch.
29.) ALARM 1 (SET-ON-OFF) Selector Switch.
30.) BUZZ-CD-RADIO Selector Switch.
31.) FM ST.-FM-AM Selector Switch.
32.) TUNING Control.
33.) AC Power Cord.
34.) Back Up Battery Compartment (Bottom Cabinet).
35.) FM Wire Antenna.
8
CKD2300_060305.p65
8
3/6/2005, 11:04
OPERATING INSTRUCTIONS
• Make sure you have installed the back-up battery in the battery
compartment.
• Make sure you have extended the AC power cord and the FM antenna
wire to their full lengths.
• Connect the AC power cord plug to a 120V 60Hz AC outlet.
Setting The Clock
When the radio is connected to the AC outlet for the first time “12:00” (AM) will
flash in the display.
PM
AL 1
AL 2
1.) First depress and hold the CLOCK SET button and then press the SKIP/
SEARCH
/ HOUR button to set the clock to the correct hour, AM or PM. If
the PM indicator is ‘Off’ the time displayed is AM.
2.) Continue to depress the CLOCK SET button and then depress the SKIP/
SEARCH
/ MIN. button to adjust the display to the correct minute.
3.) When the correct time appears on the display release all the buttons. The
clock begins to run.
PM
AL 1
AL 2
9
CKD2300_060305.p65
9
3/6/2005, 11:04
Setting The Wake-Up Times
The procedure for setting the Alarm 1 and Alarm 2 wake up times
is the same.
1.) Slide the ALARM 1 switch, located on the left side of the
cabinet to the “SET” position.
ALARM 1
The display changes from the correct time to
PM
the Alarm 1 wake-up time. The first time you
AL 1
AL 2
set the Alarm 1 or Alarm 2 wake-up time the
display will flash “12:00” (AM).
2.) Press the SKIP/ SEARCH
/ HOUR button to set the display to the desired
Alarm 1 wake-up hour, AM or PM. If the PM indicator is ‘Off’ the wake-up hour
displayed is AM.
3.) Press the SKIP/SEARCH
/ MIN. button to adjust the display to the desired
Alarm 1 wake-up minute.
4.) Slide the ALARM 1 switch back to the “OFF” position. The display changes
from the Alarm 1 wake-up time back to the correct time.
5.) Follow the same procedure to set the Alarm 2 wake-up time if desired.
To check the wake-up times just slide the ALARM 1 or ALARM 2 button to the
“SET” position at any time. Slide the switches back to the “OFF” position to return
to the correct time.
Note: If both of the Alarm switches are set to “SET” at the same time the clock
will display the correct current time, not the Alarm 1 or Alarm 2 wake up time.
So be sure to set the ALARM 1 switch back to the “ON” or “OFF” position
before setting the ALARM 2 switch to the “SET” position.
10
CKD2300_060305.p65
10
3/6/2005, 11:04
Listening To The Radio
1.) Slide the Function selector (RADIO/CD/BUZZ) switch, located
on the right side cabinet, to the “RADIO” position.
2.) Slide the Band selector (AM/FM/FM ST.) switch, located on
the right side cabinet, to the desired band.
3.) Press the POWER button on the front panel to turn the system
‘On’. The Power indicator comes ‘On’.
4.) Tune to the desired station by slowly rotating the TUNING
control on the right side.
PM
If you tune to an FM Stereo
AL 1
AL 2
station the FM ST. indicator
will come ‘On’.
Note: If you tune to a distant FM stereo station and the
reception is noisy or weak, slide the Band selector to the
FM position. The reception will usually improve but the
sound will no longer be in stereo.
5.) Adjust the VOLUME control, located on the left side of the
cabinet, to the desired level.
6.) When you are finished listening press the POWER button on
the front panel to shut the radio ‘Off’. The POWER indicator
goes ‘Off’.
11
CKD2300_060305.p65
11
3/6/2005, 11:04
Hints For Better Reception
FM – The FM lead wire antenna on the back panel should be extended to its full
length. You may also have to vary the direction of this antenna until you find the
position that provides the best reception.
AM – The AM ferrite bar antenna is inside the cabinet. If the AM reception is
unsatisfactory try rotating the entire cabinet slightly until the internal antenna picks
up the strongest signal.
12
CKD2300_060305.p65
12
3/6/2005, 11:04
Playing Compact Discs
Note: Although this CD player can read CD-R and CD-RW discs, in addition to
normal CDs, the playability of CD-R/RW discs may be affected by the type of
software that was used to create the discs, as well as the quality and condition of
the blank media you are using. 100% playability cannot be guaranteed. This is not
an indication of a problem with the player.
1.) Slide the Function (RADIO/CD/BUZZ) selector switch on the
right side cabinet to the CD position.
2.) Press the POWER button on the front panel to turn the system ‘On’. The
POWER indicator comes ‘On’.
3.) Press on the CD door in the area marked OPEN/CLOSE and fully open the
door. If you have not already done so remove the dummy CD transit protection
card and discard.
4.) Place a CD on the center spindle with the printed label side facing you. Gently
press downward on the disc near the center hole until it is properly ‘seated’ on
the spindle. Close the CD door.
MUSIC
13
CKD2300_060305.p65
13
3/6/2005, 11:04
5.) The disc will spin for a few seconds as the player reads the disc. Then the disc
will stop and the display will show the total number of tracks on the disc. After
5 seconds the display returns to the correct time.
PM
PM
AL 1
AL 1
AL 2
AL 2
6.) Press the PLAY/PAUSE button on the front panel to begin playback on track
01. Track number “01” appears in the display. After 5 seconds the display
returns to the correct time.
PM
PM
AL 1
AL 1
AL 2
AL 2
7.) Adjust the VOLUME control to the desired level.
8.) Playback will continue until the last track has played then the disc stops. To
stop playback before the disc ends press the STOP button on the front panel.
If you are finished listening open the CD door and remove your disc.
9.) To listen to the radio slide the Function selector switch (RADIO/CD/BUZZ) to
the RADIO position, or press the POWER button to turn the power ‘Off’.
Note: To see the CD track number during playback, press the CD DISPLAY
button on the front panel. The display will change from correct time to CD
track number for 5 seconds, and then return to the correct time display.
Pause Control
PM
To pause momentarily during CD playback press
AL 1
the PLAY/PAUSE button on the front panel again.
AL 2
The sound stops and the track number flashes for
5 seconds but the disc continues to spin.
Press the PLAY/PAUSE button again to cancel the Pause mode and resume normal
playback. The sound resumes at the same point on the disc.
14
CKD2300_060305.p65
14
3/6/2005, 11:04
/
Skip/Search Controls
During playback press the SKIP/SEARCH FWD
or SKIP/SEARCH REV
buttons on the front panel repeatedly to skip forward or back to higher or lower
numbered tracks. Playback will start at the beginning of the selected track.
To search within a track for a specific musical passage depress and hold the
SKIP/SEARCH FWD
or SKIP/SEARCH REV
buttons on the front panel.
The player will search rapidly forward or backward as long as the buttons are
depressed. When you hear the desired passage release the buttons and normal
playback will resume at that point.
Note: The volume is automatically reduced during high-speed music search.
To start playback from a specific track load your disc as usual and wait until the
display shows the total number of tracks. Press the SKIP/SEARCH FWD
or
SKIP/SEARCH REV buttons repeatedly until the desired track number appears
in the display then press the PLAY/PAUSE button to begin playback on the desired
track.
15
CKD2300_060305.p65
15
3/6/2005, 11:04
Special Playback Modes
Repeat Playback
You can program the player to continuously repeat a single track or the entire disc.
The Repeat mode can be selected while the disc is playing or while the disc is
stopped.
Single Track Repeat
Select the track to be repeated and then press the REPEAT button on the front
panel once.
PM
The REPEAT indicator begins ‘flashing’.
AL 1
AL 2
If necessary, press the PLAY/PAUSE button to
begin playback. The selected track will be repeated
continuously.
All Tracks Repeat
Press the REPEAT button on the front panel twice.
PM
The REPEAT indicator remains ‘On’.
AL 1
AL 2
If necessary, press the PLAY/PAUSE button to
begin playback. The entire disc will be repeated
continuously.
To cancel Repeat playback press the REPEAT button on the front panel until the
REPEAT indicator goes ‘Off’. Repeat Playback mode may also be cancelled by
opening the CD door, switching to RADIO function, or pressing the POWER button
to shut the power ‘Off’.
16
CKD2300_060305.p65
16
3/6/2005, 11:04
Random Playback
The Random playback feature allows you to play all the tracks on a disc in random
order.
1.) Load your disc in the player as usual and wait until the total tracks appear on
the display.
PM
AL 1
2.) Press the RANDOM button on the front panel.
AL 2
The RANDOM indicator comes ‘On’.
3.) Press the PLAY/PAUSE button to begin Random playback. The player will
select one of the tracks at Random and begin playback on that track.
After all tracks have been played in random order the player stops but the
RANDOM indicator remains ‘On’.
If you press the PLAY/PAUSE button while the RANDOM indicator is ‘On’ the
tracks will again play in random order.
4.) To cancel Random playback, press the RANDOM button again. The RANDOM
indicator goes ‘Off’. Random playback is also canceled by pressing the POWER
button to shut the system ‘Off’.
17
CKD2300_060305.p65
17
3/6/2005, 11:04
Programmed Playback
Use the Programmed Playback feature to play up to 20 tracks on a disc in any
desired order. You may also program a particular track to play several times within
a programmed sequence if desired.
Note: You cannot program a disc while it is playing. Press the STOP button to
stop playback and then follow the programming steps below.
PM
1.) Load your disc as usual and wait until the display
shows the total number of tracks on the disc.
AL 1
AL 2
2.) Press the PROGRAM button on the front panel.
PM
The PROGRAM indicator flashes and Program
AL 1
AL 2
number “P 01” appears in the display.
3.) Press the SKIP/SEARCH FWD
or SKIP/SEARCH REV
buttons to select
the first track number to be programmed.
PM
AL 1
AL 2
Example: Track number 07.
When the desired track number flashes in the
display press the PROGRAM button again.
Track “07” is now entered in Program Memory
number “01”. The program number advances
to “P 02”.
PM
AL 1
AL 2
Important: You must enter a track number in the program memory while
the PROGRAM indicator is flashing. If the PROGRAM indicator stops
flashing and the display returns to the correct time, press the PROGRAM
button again and then select the desired track number within 10 seconds.
4.) Repeat step 3, selecting a different track number each time until you have
entered up to 20 tracks in the program memory.
To confirm the program after you have entered the last track press the
PROGRAM button repeatedly. The display will scroll through all the tracks you
programmed in sequence.
18
CKD2300_060305.p65
18
3/6/2005, 11:04
5.) When you have completed programming the desired tracks press the PLAY/
PAUSE button to begin programmed playback.
The PROGRAM indicator stops flashing and remains ‘On’.
PM
PM
AL 1
AL 1
AL 2
AL 2
Playback will begin on the first track you programmed and will continue until
the last programmed track has played.
6.) When the program is completed the player stops, however the program
sequence remains in the memory.
To repeat the program sequence, press the PLAY/PAUSE button again.
To cancel the Programmed sequence from memory, press the PROGRAM
button and then press the STOP button while the player is stopped. The
PROGRAM indicator goes ‘Off’. Programmed Playback is also canceled by
switching to Radio function or opening the CD door.
Programmed Repeat Playback
You may use the Programmed Playback and Repeat features together to
continuously repeat a programmed sequence.
First program the desired sequence according to steps 1 through 4 above. When
Programmed Playback begins press the REPEAT button twice to select the Repeat
All Tracks mode.
The REPEAT indicator remains ‘On’ together with the PROGRAM indicator. The
programmed sequence will be repeated continuously.
PM
PM
AL 1
AL 1
AL 2
AL 2
19
CKD2300_060305.p65
19
3/6/2005, 11:04
Alarm Function
You can use the alarm function to wake you to an electronic Buzzer tone, the
Radio, or your favorite CD.
First slide the ALARM 1 or ALARM 2 selector switches to the “SET” to check the
Wake Up time settings. Adjust the Wake Up times if necessary.
Wake To Buzzer
1.) Slide the ALARM 1 and/or ALARM 2 selector switches on
the left side panel to the “ON” position.
The AL 1 and/or AL 2 indicators appear in the
PM
display.
AL 1
AL 2
2.) Slide the Function (RADIO/CD/BUZZ) selector to the “BUZZ”
position.
3.) At the selected wake up time the buzzer will sound. The buzzer alarm will
continue for 90 minutes and then shut ‘Off’ automatically.
To stop the Buzzer alarm sooner, press the POWER button to turn unit ‘Off’.
20
CKD2300_060305.p65
20
3/6/2005, 11:04
Wake To Radio
1.) Tune to the desired radio station and adjust the volume to the level you want to
hear in the morning when the alarm comes on.
Press the POWER button to shut the system ‘Off’.
2.) Slide the ALARM 1 and/or ALARM 2 selector switches on
the left side panel to the “ON” position.
The AL 1 and/or AL 2 indicators appear in the display.
3.) Slide the Function (RADIO/CD/BUZZ) selector to the “RADIO”
position.
4.) At the selected wake up time the radio will turn on. It will continue for 90 minutes
and then shut off automatically.
To stop the Radio alarm sooner, press the POWER button to turn unit ‘Off’.
21
CKD2300_060305.p65
21
3/6/2005, 11:04
Wake To CD
1.) Load the desired CD, begin playback and adjust the volume to the desired
level. Press the POWER button to shut the system ‘Off’.
2.) Slide the ALARM 1 and/or ALARM 2 selector switches on the
left side panel to the “ON” position.
The AL 1 and/or AL 2 indicators will appear in the display.
3.) At the selected wake up time the CD will begin to play. It will
continue for 90 minutes, or until the end of the disc, and then
shut ‘Off’ automatically.
To stop the CD alarm immediately, press the STOP button or
press the POWER button to turn unit ‘Off’.
The Alarm will automatically repeat each day at the selected Wake Up time as
long as the ALARM 1 and/or ALARM 2 selector switches are set to the “ON”
position.
To cancel the alarms, slide the ALARM 1 and/or ALARM 2 selector
switches to the “OFF” position.
The AL 1 and/or AL 2 indicators go ‘Off’.
Snooze Function
After the alarm turns on in the morning you can use the Snooze function to grab a
few more minutes sleep before the alarm sounds again.
To activate the Snooze function press the SNOOZE button on the top cabinet. The
Snooze function will stop the alarm for 6 minutes and then turn the alarm ‘On’
again.
The Snooze operation can be repeated several times within 90 minutes. But after
90 minutes the alarm will not turn on again.
22
CKD2300_060305.p65
22
3/6/2005, 11:04
Sleep Timer
You can fall asleep to the radio or CD player and the sleep timer will shut the
system off automatically after up to 90 minutes of music.
Sleep To Radio or CD Player
1.) Turn the radio ‘On’, tune to the desired station, or begin playing the desired CD
and adjust the volume to the desired level. Remember that the level you select
for the sleep mode is the same level you will hear when the alarm turns ‘On’ in
the morning.
2.) Press the SLEEP button twice. The display will
show “90”, indicating that the radio will play for
90 minutes before shutting off automatically, and
the SLEEP indicator flashes for 5 seconds.
PM
AL 1
AL 2
While the SLEEP indicator is flashing continue pressing the SLEEP button to
reduce the sleep time to 60 minutes or 30 minutes.
PM
AL 1
AL 2
3.) After 5 seconds the SLEEP indicator stops
flashing and remains ‘On’.
The radio or CD will play for the selected number of minutes and then shut ‘Off’
automatically.
Note: If you set the Sleep timer for 90 minutes but your CD is only 45
minutes long, the music will stop after the last track has played but the
power will remain ‘On’ until the Sleep timer counts down to “00”.
4.) To shut ‘Off’ the radio or CD player before the sleep timer counts down to “00”,
press the POWER button at any time. The SLEEP indicator shuts ‘Off’.
23
CKD2300_060305.p65
23
3/6/2005, 11:04
CARE AND MAINTENANCE
Compact Disc Care
• To remove a disc from its storage case, press down on the center of the case
and lift the disc out, holding it carefully by the edges.
• Fingerprints and dust should be carefully wiped off the disc’s recorded surface
with a soft cloth.Unlike conventional records, compact discs have no grooves
to collect dust and microscopic debris, so gently wiping with a soft cloth should
remove most particles. Wipe in a straight line from the inside to the outside of
the disc. Small dust particles and light stains will have absolutely no effect on
reproduction quality.
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents
or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
• Never write on or affix labels to the surface of compact discs.
24
CKD2300_060305.p65
24
3/6/2005, 11:04
Care Of The Cabinet
• If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any
wax or polish sprays on the cabinet.
• If the front panel becomes dirty or smudged with fingerprints it may be cleaned
with a soft cloth slightly dampened with a mild soap and water solution. Never
use abrasive cloths or polishes as these will mar the finish of your unit.
Caution
Never allow any water or other liquids to get inside the unit while cleaning.
TO FIND THE LOCATION AND PHONE
NUMBER OF YOUR NEAREST SERVICE
R
CENTER PERMITTED TO PERFORM
WARRANTY...
SERVICE
CALL TOLL FREE: 1-800-695-0098
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE, PLEASE WRITE TO:
Emerson Radio Corp.,
Consumer Affairs Dept.,
5101 Statesman Drive,
Irving, TX 75063.
25
CKD2300_060305.p65
25
3/6/2005, 11:04
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts
at an authorized Depot Repair Facility, or replace the product in our discretion.
For repair or replacement, pack your unit in a padded box, enclose your check or
money order payable to Emerson Radio Corp. in the amount of $9.00 (not required
by California residents) to cover shipping and handling costs, and enclose a copy
of your proof of purchase. Send your unit to:
Emerson Radio Corp.,
5101 Statesman Drive,
Irving, TX 75063.
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTYGIVES YOU SPECIFIC LEGAL RIGHTS, ANDYOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898M
The serial number of your system is located on a label on the bottom cabinet.
Please take a moment now to locate the serial number and write the number in the
space provided below. You may be asked to provide this number when calling for
product service.
Model Number: CKD2300
Serial Number:
26
CKD2300_060305.p65
26
3/6/2005, 11:04
EMERSON
Part No. 16-2999
505-01
Printed in China
CKD2300_060305.p65
27
3/6/2005, 11:04
|