CY14E256L
256 Kbit (32K x 8) nvSRAM
Features
Functional Description
■
■
■
25 ns, 35 ns, and 45 ns access times
Pin compatible with STK14C88
The Cypress CY14E256L is a fast static RAM with a nonvolatile
element in each memory cell. The embedded nonvolatile
elements incorporate QuantumTrap technology producing the
world’s most reliable nonvolatile memory. The SRAM provides
unlimited read and write cycles, while independent, nonvolatile
data resides in the highly reliable QuantumTrap cell. Data
transfers from the SRAM to the nonvolatile elements (the
STORE operation) takes place automatically at power down. On
power up, data is restored to the SRAM (the RECALL operation)
from the nonvolatile memory. Both the STORE and RECALL
operations are also available under software control. A hardware
STORE is initiated with the HSB pin.
Hands off automatic STORE on power down with external 68
µF capacitor
■
STORE to QuantumTrap™ nonvolatile elements is initiated by
software, hardware, or AutoStore™ on power down
■
■
■
■
■
■
■
■
RECALL to SRAM initiated by software or power up
Unlimited READ, WRITE, and RECALL cycles
1,000,000 STORE cycles to QuantumTrap
100 year data retention to QuantumTrap
Single 5V+10% operation
Commercial and industrial temperature
32-pin SOIC and CDIP (300 mil) packages
RoHS compliance
Logic Block Diagram
V
CC
V
CAP
Quantum Trap
512 X 512
POWER
CONTROL
A5
STORE
A6
A7
A8
RECALL
STORE/
RECALL
CONTROL
STATIC RAM
ARRAY
512 X 512
HSB
A9
A11
A12
A13
A14
SOFTWARE
DETECT
A13
-
A0
DQ0
COLUMN I/O
DQ1
DQ2
DQ3
COLUMN DEC
DQ4
DQ5
DQ6
DQ7
A0
A4
A10
A1
A3
A2
OE
CE
WE
Cypress Semiconductor Corporation
Document Number: 001-06968 Rev. *F
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised January 30, 2009
CY14E256L
having a capacitor of between 68uF and 220uF (+ 20%) rated at
6V should be provided. The voltage on the VCAP pin is driven to
5V by a charge pump internal to the chip. A pull up is placed on
WE to hold it inactive during power up.
Device Operation
The CY14E256L nvSRAM is made up of two functional compo-
nents paired in the same physical cell. These are an SRAM
memory cell and a nonvolatile QuantumTrap cell. The SRAM
memory cell operates as a standard fast static RAM. Data in the
SRAM is transferred to the nonvolatile cell (the STORE
operation) or from the nonvolatile cell to SRAM (the RECALL
operation). This unique architecture enables the storage and
recall of all cells in parallel. During the STORE and RECALL
operations, SRAM READ and WRITE operations are inhibited.
The CY14E256L supports unlimited reads and writes similar to
a typical SRAM. In addition, it provides unlimited RECALL opera-
tions from the nonvolatile cells and up to one million STORE
operations.
Figure 2. AutoStore Mode
SRAM Read
The CY14E256L performs a READ cycle whenever CE and OE
are LOW while WE and HSB are HIGH. The address specified
on pins A0–14 determines the 32,768 data bytes accessed. When
the READ is initiated by an address transition, the outputs are
valid after a delay of tAA (READ cycle 1). If the READ is initiated
by CE or OE, the outputs are valid at tACE or at tDOE, whichever
is later (READ cycle 2). The data outputs repeatedly respond to
address changes within the tAA access time without the need for
transitions on any control input pins, and remains valid until
another address change or until CE or OE is brought HIGH, or
WE or HSB is brought LOW.
In system power mode, both VCC and VCAP are connected to the
+5V power supply without the 68 μF capacitor. In this mode, the
AutoStore function of the CY14E256L operates on the stored
system charge as power goes down. The user must, however,
guarantee that VCC does not drop below 3.6V during the 10 ms
STORE cycle.
SRAM Write
A WRITE cycle is performed whenever CE and WE are LOW and
HSB is HIGH. The address inputs must be stable prior to entering
the WRITE cycle and must remain stable until either CE or WE
goes HIGH at the end of the cycle. The data on the common IO
pins DQ0–7 are written into the memory if it has valid tSD, before
the end of a WE controlled WRITE or before the end of an CE
controlled WRITE. Keep OE HIGH during the entire WRITE cycle
to avoid data bus contention on common IO lines. If OE is left
LOW, internal circuitry turns off the output buffers tHZWE after WE
goes LOW.
To reduce unnecessary nonvolatile stores, AutoStore and
Hardware Store operations are ignored, unless at least one
WRITE operation has taken place since the most recent STORE
or RECALL cycle. Software initiated STORE cycles are
performed regardless of whether a WRITE operation has taken
place. An optional pull-up resistor is shown connected to HSB.
The HSB signal is monitored by the system to detect if an
AutoStore cycle is in progress.
AutoStore Operation
If the power supply drops faster than 20 us/volt before Vcc
reaches VSWITCH, then a 2.2 ohm resistor should be connected
between VCC and the system supply to avoid momentary excess
The CY14E256L stores data to nvSRAM using one of three
storage operations:
of current between VCC and VCAP
.
1. Hardware store activated by HSB
2. Software store activated by an address sequence
3. AutoStore on device power down
AutoStore Inhibit mode
If an automatic STORE on power loss is not required, then VCC
disabled. If the CY14E256L is operated in this configuration,
references to VCC are changed to VCAP throughout this data
sheet. In this mode, STORE operations are triggered through
software control or the HSB pin. To enable or disable Autostore
change between these three options” on the fly”.
AutoStore operation is a unique feature of QuantumTrap
technology and is enabled by default on the CY14E256L.
During normal operation, the device draws current from VCC to
charge a capacitor connected to the VCAP pin. This stored
charge is used by the chip to perform a single STORE operation.
If the voltage on the VCC pin drops below VSWITCH, the part
automatically disconnects the VCAP pin from VCC. A STORE
operation is initiated with power provided by the VCAP capacitor.
Figure 2 shows the proper connection of the storage capacitor
(VCAP) for automatic store operation. A charge storage capacitor
Document Number: 001-06968 Rev. *F
Page 3 of 18
CY14E256L
Figure 3. AutoStore Inhibit Mode
If the CY14E256L is in a WRITE state at the end of power up
RECALL, the SRAM data is corrupted. To help avoid this
situation, a 10 Kohm resistor is connected either between WE
and system VCC or between CE and system VCC
.
Software STORE
Data is transferred from the SRAM to the nonvolatile memory by
a software address sequence. The CY14E256L software
STORE cycle is initiated by executing sequential CE controlled
READ cycles from six specific address locations in exact order.
During the STORE cycle, an erase of the previous nonvolatile
data is first performed followed by a program of the nonvolatile
elements. When a STORE cycle is initiated, input and output are
disabled until the cycle is completed.
Because a sequence of READs from specific addresses is used
for STORE initiation, it is important that no other READ or WRITE
accesses intervene in the sequence. If they intervene, the
sequence is aborted and no STORE or RECALL takes place.
To initiate the software STORE cycle, the following READ
sequence is performed:
1. Read address 0x0E38, Valid READ
2. Read address 0x31C7, Valid READ
3. Read address 0x03E0, Valid READ
4. Read address 0x3C1F, Valid READ
5. Read address 0x303F, Valid READ
6. Read address 0x0FC0, Initiate STORE cycle
Hardware STORE (HSB) Operation
The CY14E256L provides the HSB pin for controlling and
acknowledging the STORE operations. The HSB pin is used to
request a hardware STORE cycle. When the HSB pin is driven
LOW, the CY14E256L conditionally initiates a STORE operation
after tDELAY. An actual STORE cycle only begins if a WRITE to
the SRAM takes place since the last STORE or RECALL cycle.
The HSB pin also acts as an open drain driver that is internally
driven LOW to indicate a busy condition, while the STORE
(initiated by any means) is in progress. Pull up this pin with an
external 10K ohm resistor to VCAP if HSB is used as a driver.
The software sequence is clocked with CE controlled READs.
When the sixth address in the sequence is entered, the STORE
cycle commences and the chip is disabled. It is important that
READ cycles and not WRITE cycles are used in the sequence.
It is not necessary that OE is LOW for a valid sequence. After the
tSTORE cycle time is fulfilled, the SRAM is again activated for
READ and WRITE operation.
SRAM READ and WRITE operations, that are in progress when
HSB is driven LOW by any means, are given time to complete
before the STORE operation is initiated. After HSB goes LOW,
the CY14E256L continues SRAM operations for tDELAY. During
tDELAY, multiple SRAM READ operations take place. If a WRITE
is in progress when HSB is pulled LOW, it allows a time, tDELAY
to complete. However, any SRAM WRITE cycles requested after
HSB goes LOW are inhibited until HSB returns HIGH.
Software RECALL
Data is transferred from the nonvolatile memory to the SRAM by
a software address sequence. A software RECALL cycle is
initiated with a sequence of READ operations in a manner similar
to the software STORE initiation. To initiate the RECALL cycle,
the following sequence of CE controlled READ operations is
performed:
During any STORE operation, regardless of how it is initiated,
the CY14E256L continues to drive the HSB pin LOW, releasing
it only when the STORE is complete. After completing the
STORE operation, the CY14E256L remains disabled until the
HSB pin returns HIGH.
1. Read address 0x0E38, Valid READ
2. Read address 0x31C7, Valid READ
3. Read address 0x03E0, Valid READ
4. Read address 0x3C1F, Valid READ
5. Read address 0x303F, Valid READ
6. Read address 0x0C63, Initiate RECALL cycle
If HSB is not used, it is left unconnected.
Hardware RECALL (Power Up)
Internally, RECALL is a two step procedure. First, the SRAM data
is cleared, and then the nonvolatile information is transferred into
the SRAM cells. After the tRECALL cycle time, the SRAM is once
again ready for READ and WRITE operations. The RECALL
operation does not alter the data in the nonvolatile elements. The
nonvolatile data can be recalled an unlimited number of times.
During power up or after any low power condition (VCC
<
V
RESET), an internal RECALL request is latched. When VCC
once again exceeds the sense voltage of VSWITCH, a RECALL
cycle is automatically initiated and takes tHRECALL to complete.
Document Number: 001-06968 Rev. *F
Page 4 of 18
CY14E256L
Figure 4. Current Versus Cycle Time (READ)
Data Protection
The CY14E256L protects data from corruption during low
voltage conditions by inhibiting all externally initiated STORE
and WRITE operations. The low voltage condition is detected
when VCC is less than VSWITCH. If the CY14E256L is in a WRITE
mode (both CE and WE are low) at power up after a RECALL or
after a STORE, the WRITE is inhibited until a negative transition
on CE or WE is detected. This protects against inadvertent writes
during power up or brown out conditions.
Noise Considerations
The CY14E256L is a high speed memory. It must have a high
frequency bypass capacitor of approximately 0.1 µF connected
between VCC and VSS, using leads and traces that are as short
as possible. As with all high speed CMOS ICs, careful routing of
power, ground, and signals reduce circuit noise.
Figure 5. Current Versus Cycle Time (WRITE)
Hardware Protect
The CY14E256L offers hardware protection against inadvertent
STORE operation and SRAM WRITEs during low voltage condi-
tions. When VCAP<VSWITCH, all externally initiated STORE
operations and SRAM WRITEs are inhibited. AutoStore can be
completely disabled by tying VCC to ground and applying + 5V
to VCAP. This is the AutoStore Inhibit mode; in this mode,
STOREs are only initiated by explicit request using either the
software sequence or the HSB pin.
Low Average Active Power
CMOS technology provides the CY14E256L the benefit of
drawing significantly less current when it is cycled at times longer
READ or WRITE cycle time. Worst case current consumption is
shown for both CMOS and TTL input levels (commercial temper-
ature range, VCC = 5.5V, 100% duty cycle on chip enable). Only
standby current is drawn when the chip is disabled. The overall
average current drawn by the CY14E256L depends on the
following items:
Preventing Store
The STORE function is disabled by holding HSB high with a
driver capable of sourcing 30 mA at a VOH of at least 2.2V,
because it has to overpower the internal pull down device. This
device drives HSB LOW for 20 μs at the onset of a STORE.
When the CY14E256L is connected for AutoStore operation
■
■
■
■
■
■
■
The duty cycle of chip enable
The overall cycle rate for accesses
The ratio of READs to WRITEs
CMOS versus TTL input levels
The operating temperature
The VCC level
(system VCC connected to VCC and a 68 μF capacitor on VCAP
)
and VCC crosses VSWITCH on the way down, the CY14E256L
attempts to pull HSB LOW. If HSB does not actually get below
VIL, the part stops trying to pull HSB LOW and abort the STORE
attempt.
IO loading
Document Number: 001-06968 Rev. *F
Page 5 of 18
CY14E256L
manufacturing test to ensure these system routines work
consistently.
Best Practices
nvSRAM products have been used effectively for over 15 years.
While ease of use is one of the product’s main system values,
experience gained working with hundreds of applications has
resulted in the following suggestions as best practices:
■
Power up boot firmware routines should rewrite the nvSRAM
into the desired state. While the nvSRAM is shipped in a preset
state, best practice is to again rewrite the nvSRAM into the
desired state as a safeguard against events that might flip the
bit inadvertently (program bugs, incoming inspection routines,
and so on).
■
The nonvolatile cells in an nvSRAM are programmed on the
test floor during final test and quality assurance. Incoming
inspection routines at customer or contract manufacturer’s
sitessometimesreprogramthesevalues. FinalNVpatternsare
typically repeating patterns of AA, 55, 00, FF, A5, or 5A. End
product’s firmware should not assume an NV array is in a set
programmed state. Routines that check memory content
values to determine first time system configuration, cold or
warm boot status, and so on should always program a unique
NV pattern (for example, complex 4-byte pattern of 46 E6 49
53 hex or more random bytes) as part of the final system
■
TheVCAP valuespecifiedinthisdatasheetincludesaminimum
and a maximum value size. Best practice is to meet this
requirementandnotexceedthemaximumVCAP valuebecause
the higher inrush currents may reduce the reliability of the
internal pass transistor. Customers that want to use a larger
V
CAP value to make sure there is extra store charge should
discuss their VCAP size selection with Cypress to understand
any impact on the VCAP voltage level at the end of a tRECALL
period.
Table 1. Hardware Mode Selection
CE
H
L
WE
X
HSB
H
A13–A0
Mode
IO
Power
Standby
Active
X
X
X
X
Not Selected
Read SRAM
Write SRAM
Output High Z
Output Data
Input Data
H
H
L
L
H
[2]
X
X
L
Nonvolatile STORE Output High Z
ICC2
L
H
H
0x0E38
0x31C7
0x03E0
0x3C1F
0x303F
0x0FC0
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Output Data
Output Data
Output Data
Output Data
Output Data
ICC2
Nonvolatile STORE Output High Z
L
H
H
0x0E38
0x31C7
0x03E0
0x3C1F
0x303F
0x0C63
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Output Data
Output Data
Output Data
Output Data
Output Data
Nonvolatile RECALL Output High Z
Notes
1. I/O state assumes OE < V . Activation of nonvolatile cycles does not depend on state of OE.
IL
2. HSB STORE operation occurs only if an SRAM WRITE has been done since the last nonvolatile cycle. After the STORE (if any) completes, the part goes into
standby mode, inhibiting all operations until HSB rises.
3. CE and OE LOW and WE HIGH for output behavior.
4. The six consecutive addresses must be in the order listed. WE must be high during all six consecutive CE controlled cycles to enable a nonvolatile cycle.
5. While there are 15 addresses on the CY14E256L, only the lower 14 are used to control software modes.
Document Number: 001-06968 Rev. *F
Page 6 of 18
CY14E256L
Package Power Dissipation
Capability (TA = 25°C) ................................................... 1.0W
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. These user guidelines are not tested.
Surface Mount Lead Soldering
Temperature (3 Seconds).......................................... +260°C
Storage Temperature ................................. –65°C to +150°C
DC output Current (1 output at a time, 1s duration) .... 15 mA
Ambient Temperature with
Power Applied ............................................ –55°C to +125°C
Static Discharge Voltage.......................................... > 2001V
(MIL-STD-883, Method 3015)
Supply Voltage on VCC Relative to GND ..........–0.5V to 7.0V
Latch Up Current ................................................... > 200 mA
Voltage Applied to Outputs
in High Z State.......................................–0.5V to VCC + 0.5V
Operating Range
Input Voltage...........................................–0.5V to Vcc + 0.5V
Range
Commercial
Industrial
Ambient Temperature
0°C to +70°C
VCC
Transient Voltage (<20 ns) on
Any Pin to Ground Potential ..................–2.0V to VCC + 2.0V
4.5V to 5.5V
4.5V to 5.5V
-40°C to +85°C
DC Electrical Characteristics
Parameter
Description
Test Conditions
Min
Max
Unit
ICC1
Average VCC Current
tRC = 25 ns
Commercial
97
80
70
mA
mA
t
t
RC = 35 ns
RC = 45 ns
Dependent on output loading and cycle rate.
Values obtained without output loads.
Industrial
100
85
70
mA
mA
mA
I
OUT = 0 mA.
ICC2
ICC3
Average VCC Current
during STORE
All Inputs Do Not Care, VCC = Max
Average current for duration tSTORE
3
mA
mA
Average VCC Current at
WE > (VCC – 0.2V). All other inputs cycling.
Dependent on output loading and cycle rate. Values obtained
without output loads.
10
t
RC= 200 ns, 5V, 25°C
Typical
ICC4
Average VCAP Current
during AutoStore Cycle
All Inputs Do Not Care, VCC = Max
Average current for duration tSTORE
2
mA
mA
[7]
ISB
VCC Standby Current
CE > (VCC – 0.2V). All others VIN < 0.2V or > (VCC – 0.2V).
Standby current level after nonvolatile cycle is complete.
Inputs are static. f = 0 MHz.
1.5
[7]
ISB1
VCC Standby Current
(Standby, Cycling TTL
Input Levels)
tRC = 25 ns, CE > VIH
tRC = 35 ns, CE > VIH
tRC = 45 ns, CE > VIH
Commercial
30
25
22
mA
mA
mA
Industrial
31
26
23
mA
mA
mA
IIX
Input Leakage Current
VCC = Max, VSS < VIN < VCC
-1
-5
+1
+5
μA
μA
IOZ
Off State Output Leakage VCC = Max, VSS < VIN < VCC, CE or OE > VIH or WE < VIL
Current
VIH
VIL
Input HIGH Voltage
2.2
VCC
0.5
+
V
V
V
Input LOW Voltage
VSS
0.5
–
0.8
VOH
Output HIGH Voltage
IOUT = –4 mA
2.4
Notes
6.
V
reference levels throughout this data sheet refer to V if that is where the power supply connection is made, or V
if V is connected to ground.
CC
CC
CAP CC
7. CE > V does not produce standby current levels until any nonvolatile cycle in progress has timed out.
IH
Document Number: 001-06968 Rev. *F
Page 7 of 18
CY14E256L
DC Electrical Characteristics
Over the operating range (continued)(VCC = 4.5V to 5.5V) [6]
Parameter
VOL
Description
Test Conditions
Min
Max
0.4
Unit
V
Output LOW Voltage
IOUT = 8 mA
VBL
Logic ‘0’ Voltage on HSB IOUT = 3 mA
Output
0.4
V
VCAP
Storage Capacitor
Between VCAP pin and Vss, 6V rated. 68 µF +20% nom.
54
260
uF
Data Retention and Endurance
Parameter
Description
Min
100
Unit
DATAR
NVC
Data Retention
Nonvolatile STORE Operations
Years
K
1,000
Capacitance
Parameter
CIN
COUT
Description
Input Capacitance
Output Capacitance
Test Conditions
TA = 25°C, f = 1 MHz,
CC = 0 to 3.0V
Max
5
Unit
pF
V
7
pF
Thermal Resistance
In the following table, the thermal resistance parameters are listed.[8]
Parameter
Description
Test Conditions
32-SOIC
32-CDIP
Unit
ΘJA
Thermal Resistance
(Junction to Ambient)
Test conditions follow standard test methods
and procedures for measuring thermal
impedance, per EIA / JESD51.
35.45
TBD
°C/W
ΘJC
Thermal Resistance
(Junction to Case)
13.26
TBD
°C/W
Figure 6. AC Test Loads
For Tri-state Specs
R1 963
Ω
R1 963Ω
5.0V
5.0V
Output
Output
R2
R2
512
30 pF
5 pF
512Ω
Ω
AC Test Conditions
Input Pulse Levels....................................................0V to 3V
Input Rise and Fall Times (10% - 90%)........................ <5 ns
Input and Output Timing Reference Levels.................... 1.5V
Note
8. These parameters are guaranteed by design and are not tested.
Document Number: 001-06968 Rev. *F
Page 8 of 18
CY14E256L
AC Switching Characteristics
SRAM Read Cycle
Parameter
25 ns
35 ns
45 ns
Unit
Description
Cypress
Alt
Min
Max
Min
Max
Min
Max
Parameter
tACE
tELQV
tAVAV, ELEH
tAVQV
Chip Enable Access Time
Read Cycle Time
25
35
45
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tRC
t
25
35
45
tAA
tDOE
Address Access Time
25
10
35
15
45
20
tGLQV
Output Enable to Data Valid
Output Hold After Address Change
Chip Enable to Output Active
Chip Disable to Output Inactive
Output Enable to Output Active
Output Disable to Output Inactive
Chip Enable to Power Active
Chip Disable to Power Standby
[10]
tOHA
tAXQX
5
5
5
5
5
5
tLZCE
tHZCE
tLZOE
tHZOE
tELQX
tEHQZ
10
10
25
13
13
35
15
15
45
tGLQX
0
0
0
0
0
0
tGHQZ
[8]
tPU
tELICCH
tEHICCL
[8]
tPD
Switching Waveforms
W5&
$''5(66
W$$
W2+$
'4ꢀꢁ'$7$ꢀ287ꢂ
'$7$ꢀ9$/,'
W5&
$''5(66
&(
W$&(
W3'
W+=&(
W/=&(
2(
W+=2(
W'2(
W/=2(
'4ꢀꢁ'$7$ꢀ287ꢂ
'$7$ꢀ9$/,'
$&7,9(
W38
67$1'%<
,&&
Notes
9. WE and HSB must be HIGH during SRAM Read cycles.
10. Device is continuously selected with CE and OE both Low.
11. Measured ±200 mV from steady state output voltage.
Document Number: 001-06968 Rev. *F
Page 9 of 18
CY14E256L
SRAM Write Cycle
Parameter
25 ns
35 ns
45 ns
Unit
Description
Write Cycle Time
Cypress
Parameter
Alt
Min
Max
Min
Max
Min
Max
tWC
tAVAV
tWLWH, WLEH
tELWH, ELEH
tDVWH, DVEH
tWHDX, EHDX
tAVWH, AVEH
tAVWL, AVEL
tWHAX, EHAX
tWLQZ
tWHQX
25
20
20
10
0
35
25
25
12
0
45
30
30
15
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tPWE
tSCE
tSD
tHD
tAW
tSA
tHA
tHZWE
tLZWE
t
Write Pulse Width
t
Chip Enable To End of Write
Data Setup to End of Write
Data Hold After End of Write
Address Setup to End of Write
Address Setup to Start of Write
Address Hold After End of Write
Write Enable to Output Disable
Output Active After End of Write
t
t
t
20
0
25
0
30
0
t
t
0
0
0
10
13
15
5
5
5
Switching Waveforms
tWC
ADDRESS
CE
tHA
tSCE
tAW
tSA
tPWE
WE
tHD
tSD
DATA VALID
DATA IN
tHZWE
tLZWE
HIGH IMPEDANCE
PREVIOUS DATA
DATA OUT
tWC
ADDRESS
tHA
tSCE
tSA
CE
WE
tAW
tPWE
tSD
tHD
DATA IN
DATA VALID
HIGH IMPEDANCE
DATA OUT
Notes
12. If WE is Low when CE goes Low, the outputs remain in the high impedance state.
13. HSB must be high during SRAM WRITE cycles.
14.
CE or WE must be greater than V during address transitions.
IH
Document Number: 001-06968 Rev. *F
Page 10 of 18
CY14E256L
AutoStore or Power Up RECALL
CY14E256L
Parameter
Alt
Description
Unit
Min
Max
[15]
tHRECALL
tRESTORE
tHLHZ
tHLQZ , BLQZ
Power up RECALL Duration
STORE Cycle Duration
550
10
μs
ms
μs
V
[16]
tSTORE
tDELAY
t
Time Allowed to Complete SRAM Cycle
Low Voltage Trigger Level
Low Voltage Reset Level
1
VSWITCH
VRESET
tVCCRISE
4.0
4.5
3.6
V
VCC Rise Time
150
μs
ns
[13]
tVSBL
Low Voltage Trigger (VSWITCH) to HSB low
300
Switching Waveforms
Figure 11. AutoStore/Power Up RECALL
WE
Notes
15. t
starts from the time V rises above V
.
SWITCH
HRECALL
CC
16. CE and OE low and WE high for output behavior.
17. HSB is asserted low for 1us when V
drops through V
. If an SRAM WRITE has not taken place since the last nonvolatile cycle, HSB is released and no store
CAP
SWITCH
takes place.
Document Number: 001-06968 Rev. *F
Page 11 of 18
CY14E256L
Software Controlled STORE/RECALL Cycle
The software controlled STORE/RECALL cycle follows. [19]
25 ns
35 ns
45 ns
Unit
Parameter
Alt
Description
Min
Max
Min
Max
Min
Max
tRC
tAVAV
tAVEL
tELEH
tELAX
STORE/RECALL Initiation Cycle Time
Address Setup Time
25
0
35
0
45
0
ns
ns
ns
ns
μs
tSA
tCW
Clock Pulse Width
20
20
25
20
30
20
tHACE
Address Hold Time
tRECALL
RECALL Duration
20
20
20
Switching Waveforms
tRC
tRC
ADDRESS # 1
ADDRESS # 6
ADDRESS
CE
tSA
tSCE
tHACE
OE
t
STORE / tRECALL
HIGH IMPEDANCE
DATA VALID
DATA VALID
DQ (DATA)
Notes
18. The software sequence is clocked on the falling edge of CE without involving OE (double clocking aborts the sequence).
19. The six consecutive addresses must be read in the order listed in the Mode Selection table. WE must be HIGH during all six consecutive cycles.
Document Number: 001-06968 Rev. *F
Page 12 of 18
CY14E256L
Hardware STORE Cycle
CY14E256L
Parameter
Alt
Description
Unit
Min
Max
tDHSB
tPHSB
tHLBL
tRECOVER, HHQX
t
Hardware STORE High to Inhibit Off
Hardware STORE Pulse Width
700
ns
ns
ns
tHLHX
15
Hardware STORE Low to STORE Busy
300
Switching Waveforms
Figure 13. Hardware STORE Cycle
Note
20. t
is only applicable after t
is complete.
STORE
DHSB
Document Number: 001-06968 Rev. *F
Page 13 of 18
CY14E256L
Part Numbering Nomenclature (Commercial and Industrial)
CY 14 E 256 L- SZ 25 X C T
Option:
T-Tape and Reel
Blank - Std.
Temperature:
C - Commercial (0 to 70°C)
I - Industrial (-40 to 85°C)
Speed:
Pb-Free
25 - 25 ns
35 - 35 ns
45 - 45 ns
Package
SZ - 32-SOIC
D - 32-CDIP
Data Bus:
L - x8
Density:
256 - 256 Kb
Voltage:
E - 5.0V
nvSRAM
14 - AutoStore + Software Store + Hardware Store
Cypress
Ordering Information
Speed
(ns)
Operating
Range
Ordering Code
Package Diagram
Package Type
25
CY14E256L-SZ25XCT
CY14E256L-SZ25XC
CY14E256L-SZ25XIT
CY14E256L-SZ25XI
CY14E256L-SZ35XCT
CY14E256L-SZ35XC
CY14E256L-SZ35XIT
CY14E256L-SZ35XI
CY14E256L-SZ45XCT
CY14E256L-SZ45XC
CY14E256L-SZ45XIT
CY14E256L-SZ45XI
CY14E256L-D45XI
51-85127
51-85127
51-85127
51-85127
51-85127
51-85127
51-85127
51-85127
51-85127
51-85127
51-85127
51-85127
001-51694
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin SOIC (300 mil)
32-pin CDIP (300 mil)
Commercial
Industrial
35
45
Commercial
Industrial
Commercial
Industrial
All parts are Pb-free. The above table contains Final information. Please contact your local Cypress sales representative for availability of these parts
Document Number: 001-06968 Rev. *F
Page 14 of 18
CY14E256L
Package Diagram
Figure 14. 32-Pin (300 Mil) SOIC (51-85127)
PIN 1 ID
16
1
MIN.
MAX.
DIMENSIONS IN INCHES[MM]
REFERENCE JEDEC MO-119
0.292[7.416]
0.299[7.594]
0.405[10.287]
0.419[10.642]
PART #
17
32
S32.3 STANDARD PKG.
SZ32.3 LEAD FREE PKG.
SEATING PLANE
0.810[20.574]
0.822[20.878]
0.090[2.286]
0.100[2.540]
0.004[0.101]
0.050[1.270]
TYP.
0.006[0.152]
0.012[0.304]
0.041[1.041]
0.026[0.660]
0.032[0.812]
0.021[0.533]
0.004[0.101]
0.0100[0.254]
0.014[0.355]
0.020[0.508]
51-85127-*A
Document Number: 001-06968 Rev. *F
Page 15 of 18
CY14E256L
Package Diagram (continued)
Figure 15. 32-Pin (300 Mil) CDIP (001-51694)
001-51694 **
Document Number: 001-06968 Rev. *F
Page 16 of 18
CY14E256L
Document History Page
Document Title: CY14E256L 256 Kbit (32K x 8) nvSRAM
Document Number: 001-06968
Submission
Date
Orig. of
Change
Rev.
ECN No.
Description of Change
**
427789
437321
472053
503290
See ECN
See ECN
See ECN
See ECN
TUP
TUP
TUP
PCI
New data sheet
Show data sheet on external Web
*A
*B
*C
Updated Part Numbering Nomenclature and Ordering Information
Changed from “Advance” to “Preliminary”
Changed the term “Unlimited” to “Infinite”
Changed ICC3 value from 10mA to 15mA
Removed Industrial Grade mention
Removed 35 ns speed bin
Removed ICC1 values from the DC table for 35 ns Industrial Grade
Corrected VIL min specification from (VCC - 0.5) to (VSS - 0.5)
Removed all references pertaining to OE controlled Software STORE and
RECALL operation
Changed the address locations of the software STORE/RECALL com-
mand
Updated Part Nomenclature Table and Ordering Information Table
*D
1349963
See ECN
UHA/SFV
GVCH
Changed from “Preliminary” to “Final.” Updated AC Test Conditions
Updated Ordering Information Table
*E
*F
2427986
2606744
See ECN
02/19/09
Move to external web
GVCH/PYRS Updated Feature Section
Added 35 ns access speed specs
Added CDIP package
Removed HSB ganging feature
Added footnote 5
Updates all the notes
Added Best practices
Added Industrial specs
Changed Icc3 from 15 mA to 10 mA
Added ISB1 spec
Added parameter VBL
Changed VIH test conditions from -2 and 4 to -4 and 8mA
Added footnote 6 and 7
Added tVSBL and VRESET parameter to Autostore or Power-up Recall table
Added Thermal resistance values
Changed parameter tAS to tSA
Renamed tGLAX to tHACE
Renamed tRESTORE to tDHSB
Updated Figure 13
Document Number: 001-06968 Rev. *F
Page 17 of 18
CY14E256L
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales
Products
PSoC
PSoC Solutions
General
Clocks & Buffers
Wireless
Low Power/Low Voltage
Precision Analog
LCD Drive
Memories
Image Sensors
CAN 2.0b
USB
© Cypress Semiconductor Corporation, 2006-2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-06968 Rev. *F
Revised January 30, 2009
Page 18 of 18
AutoStore and QuantumTrap are registered trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective
holders.
|