Fujitsu Printer FTP 627MCL353 User Manual

24V DRIVEN, FTP-607 Series  
2” HIGH SPEED THERMAL PRINTER  
FTP-627MCL353/354 #01 / #02  
OVERVIEW  
The FTP-627 MCL Series are 24V driven high-speed printers  
with a 2-inch paper width equivalent.  
The FTP-627 MCL Series can be used for a variety of  
applications, such as portable terminals, POS, banking  
terminals, and measurement and medical equipment.  
HIGHLIGHTS  
• Ultra compact  
Height 26.4 mm, width 83.5 mm, depth 43.0 mm  
FTP-627MCL354  
• High speed printing  
It can print at 100 mm/s (800 dotlines/s) maximum by using  
Fujitsu's unique head drive control.  
• Auto Cutter  
Full cut type (#01) and partial cut type (#02) printers are  
available.  
• Easy paper setting  
Our unique platen release mechanism allows a  
wide paper route even if the printer is ultra-compact, so  
paper can be easily inserted. Conventional auto loading is  
also available.  
1
 
FTP-627MCL353/354  
SPECIFICATIONS  
Item  
Specification  
Interface  
Conforms to RS232C / Centronics  
24 VDC average current, 1.5A (2.2A peak)  
(print ratio: 25%, print speed: 100mm/sec. )  
For print head  
Power  
supply  
For motor  
For cutter  
For logic  
24 VDC ± 5%, 1A maximum  
5 VDC ± 5%, 1A maximum  
5 VDC ± 5%, 0.1 A maximum  
83.5 x 43.0 x 26.4 mm (WxDxH)  
Approximately 120g  
Dimensions Mechanism with cutter  
Weight  
Mechanism with cutter  
Pulse resistance: 50 million pulses/dot (under our standard  
conditions); Abrasion resistance: paper traveling distance 50km  
(print ratio: 25% or less)  
Head  
Life  
Cutter  
300,000 cuts  
Operating temperature*  
Operating humidity  
Storage temperature  
Storage humidity  
0˚ C to 50˚ C  
20 to 85% RH (no condensation)  
-20˚ C to +60˚ C (paper not included)  
5 to 95% RH (no condensation)  
Operating  
environment  
Head temperature  
detection  
Detected by thermistor  
Detection  
function  
Paper out/mark detection Detected by photo-interrupter  
Platen release  
Detected by sliding switch  
High Sensitive Paper TF50KS-E4 (Nippon Paper)  
Standard paper:  
Medium Life Paper  
Long Life Paper  
TF60KS-E(Nippon Paper), FTP-  
020PU001 (58mm), PD105R (Oji Paper),  
FTP-020P0701 (58mm)  
TF60KS-F1, FTP-020P0102 (58mm),  
PD170R (Oji Paper), P220VBB-1  
Mitsubishi Paper)  
Recommended thermal sensitive paper  
PD160R-N (Oji Paper), AFB-235  
(Mitsubishi Paper), TP50KJ-R (Nippon  
Paper), HA220AA (Nippon Paper)  
*+5˚C to +40˚C printing density assurance rance.  
3
 
FTP-627MCL353/354  
DIMENSIONS  
1. Printer mechanism  
FTP-627MCL353  
FTP-627MCL354  
at release  
at close  
80.5  
83.5  
1
at release  
at close  
26.4  
1.2  
38.6  
58 +0  
26.4  
38.6  
(paper width)  
-1  
3 MAX  
3 max.  
33.7  
(37.2)  
(37.2)  
Unit: mm  
Note: 1. Dimensions are nominal value (tolerance ±5 unless otherwise specified).  
2. Platen unit (lever, platen, etc) moves by approximately 0.7mm toward paper insertion direction when platen is  
open.  
4
 
FTP-627MCL353/354  
1. Connector (FPC) specification (CN4)  
(1) Connector  
Mechanical unit side:  
FPC connector  
Remote side (housing site):  
52610-3090 (made by Molex)  
(2) Pin assignment on the mechanical side  
Signal  
PHK  
I/O Contents  
No  
1
O
O
I
Photointerrupter (Cathode)  
2
VSEN  
PHE  
SW  
SW  
VH  
Ground power supply for paper sensor  
Photointerrupter (Emittor)  
Platen open switch  
3
4
5
Platen open switch  
6
7
VH  
Power supply for thermal head  
8
VH  
9
NC  
Not connected  
Clock  
10 CLK  
11 LAT  
12 STB2  
13 STB1  
14 GND  
15 GND  
16 GND  
17 GND  
18 GND  
19 GND  
20 TH  
I
Print data latch  
Strobe 2  
I
I
Strobe 1  
O
I
Ground power supply for thermal head  
Thermistor  
Power for logic  
Strobe 3  
21 VDD  
22 STB3  
23 DI  
I
Print data in  
24 VH  
I
25 VH  
Power supply for thermal head  
Stepping motor excitation signal  
26 VH  
27 MT/A  
28 MT/A  
29 MT/B  
30 MT/B  
I
I
I
5
 
FTP-627MCL353/354  
Sensor (Photo-  
interruptor)  
Platen unit  
Thermal head  
Motor  
FPC  
Connect terminal:  
surface side  
Connector No  
30,29, .....................2,1  
(FPC pin numbers)  
2. Cutter (CN5)  
Connector on control circuit side: B4B-PH-K-S (J.S.T. or equivalent)  
No. Signal I/O  
Contents  
No. Signal I/O  
Contents  
Cutter position  
detect switch  
Home position  
detect switch  
1
3
SW1  
M+  
-
2
4
SW2  
M-  
-
Stepping motor  
coil excitation  
Stepping motor  
coil excitation  
O
I/O  
Europe  
Japan  
Fujitsu Components Europe B.V.  
Diamantlaan 25  
Fujitsu Component Limited  
Gotanda-Chuo Building  
2132 WV Hoofddorp  
Netherlands  
Tel: (31-23) 5560910  
Fax: (31-23) 5560950  
3-5, Higashigotanda 2-chome, Shinagawa-ku  
Tokyo 141, Japan  
Tel: (81-3) 5449-7010  
Fax: (81-3) 5449-2626  
Fujitsu Components  
International  
Headquarter  
Offices  
Asia Pacific  
North and South America  
Fujitsu Components America, Inc.  
250 E. Caribbean Drive  
Sunnyvale, CA 94089 U.S.A.  
Tel: (1-408) 745-4900  
Fujitsu Components Asia Ltd.  
102E Pasir Panjang Road  
#04-01 Citilink Warehouse Complex  
Singapore 118529  
Tel: (65) 6375-8560  
Fax: (1-408) 745-4970  
Fax: (65) 6273-3021  
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered  
trademarks of their respective owners. Rev. 11/12/2004.  
6
 

Extron electronic Stereo Receiver HFX 100 RX User Manual
Extron electronic Switch 305SA User Manual
Fisher Price Bouncy Seat V8606 User Manual
Fisher Price Riding Toy T3857 User Manual
Fujitsu Printer FTP 621MCL351 User Manual
GE Double Oven JGSP28 User Manual
Generac Portable Generator 5500EXL User Manual
GE Water Dispenser GN1S15CBL REV 2 User Manual
GE Water System GXSF40H User Manual
Goodman Mfg Air Conditioner 000 &12 User Manual