INSTRUCTIONS–PARTS LIST
Important Safety Instructions
309323E
D
Read all warnings and instructions
in this manual. Save these
instructions.
Pressure Roller with 20”
Fixed Extension
Model 244279, Series C
D 20 in. (50 cm) heavy-duty extension
D 9 in. (23 cm) roller frame
D 1/2 in. (13 mm) nap roller cover
D 45° swivel adapter
ti6623a
3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure
*
The best operating pressure is the lowest pressure that provides
*
an even paint supply to the roller and typically does not exceed
300 psi (2.1 MPa, 21 bar).
CAUTION
Never leave water in the pump, gun, or pressure roller.
Doing so could cause corrosion and damage from freezing.
For storage, flush the system with Graco Pump Armort or
mineral spirits/paint thinner.
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
ECOPYRIGHT 2001, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
Pressure Roller, Model
244279, Series C
Cleaning
23
This is the procedure for flushing the pressure roller.
The pump and gun you are using may have additional
flushing steps, such as cleaning filters and screens.
See the pump and gun flushing instructions.
4
1
NOTE: Leave the pressure roller attached to the gun
for this procedure.
See Pressure Relief
Procedure on page 2.
5
2
1. Relieve the pressure.
2. Remove roller cover (19) and diffuser (23) from
roller frame as follows (see Parts Drawing):
12
19
a. Using your thumb, press down on clip (5) to
release end caps (2 &4), diffuser (23) and
roller cover (19) into a pail.
ti10641a
14
b. Remove roller cover (19) from diffuser (23).
c. Pull end caps (2 & 4) off diffuser (23).
3. Clean roller cover (19), caps (2 & 4) and diffuser
(19) with water or a compatible fluid for oil–based
materials.
4. Place roller frame (1) in paint pail. Be sure the
holes in roller frame (1) are facing inside the paint
pail.
5. Prime pump with water or flushing fluid for
oil–based materials. Use the lowest pump priming
pressure setting.
7
6. Turn prime/spray valve to SPRAY.
17
NOTE: Perform Step 7 at the lowest pressure
possible.
7*
7. Trigger gun until flushing fluid begins to dilute the
paint.
Parts List
8. Place roller frame (1) in another bucket and
continue flushing until fluid coming out of the roller
frame (1) is clear.
Ref.
No.
Part No. Description
Qty.
9. Shut off the pump. Turn prime/spray valve to
1
2
4
FRAME, roller
CAP, end (includes seal and retainer)
CAP, end (includes seal, retainer, and
o–ring)
CLIP, roller
GASKET
1
1
PRIME.
245999
246277
Storage
1
1
2
5
7
197106
15H622
If you are going to store the airless equipment for an
extended period of time after flushing with water-base
fluid, flush again with Graco Pump Armor or mineral
spirits/paint thinner. Leave the fluid in the system
during storage.
12
14
19
115524
232122
107590
GASKET
1
1
EXTENSION, 20 in. (50 cm)
ROLLER, cover, 9 inch,
1/2 in. (13 mm) nap
1
2
1
23
25
15B065
224399
DIFFUSER
SWIVEL, 45°
309323
3
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility
of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
TO PLACE AN ORDER, contact your Graco distributor, or call 1–800–690–2894 to identify the distributor closest to you.
All written and visual data contained in this document reflect the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 309323
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
309323E
8/2001 Rev. 9/2007
4
309323
|