Graco Inc Power Roller 287713 User Manual

Instructions  
Important Safety Instructions  
Read all warnings and instructions in this manual.  
Save these instructions.  
311082B  
Pressure Roller with  
20-inch Fixed Extension  
- For application of architectural paints and coatings -  
Model 287713, Series A  
20 inch (50 cm) heavy-duty extension  
9 inch (23 cm) roller frame  
1/2 inch (13 mm) nap roller cover  
WLꢀꢀꢁꢂD  
3600 psi (24.8 MPa, 248 bar) Maximum Working  
Pressure*  
*The best operating pressure is the lowest pressure that  
provides an even paint supply to the roller and typically  
does not exceed 300 psi (2.1 MPa, 21 bar).  
CAUTION  
Never leave water in pump, gun or pressure roller.  
Doing so could cause corrosion and damage from  
freezing. For storage, flush the system with Pump  
Defenderor mineral spirits/paint thinner.  
 
Pressure Relief Procedure  
Pressure Relief Procedure  
Trigger Lock  
Always engage the trigger lock  
when you stop spraying to pre-  
vent the gun from being triggered  
accidentally by hand or if  
Follow this Pressure Relief Procedure when you stop  
spraying and before cleaning, checking, servicing, or  
transporting equipment.  
dropped or bumped.  
1. Turn power switch OFF and  
unplug sprayer power cord.  
ti4218a  
Operation  
WLꢀꢁꢂꢃD  
2. Turn spray/prime valve to  
PRIME to relieve pressure.  
1. Follow pump priming instructions provided in your  
sprayer operation manual using the lowest pressure  
setting at which the pump primes.  
35,0(  
2. Turn prime/spray valve to SPRAY  
WLꢀꢁꢄꢄD  
position.  
3. Hold metal part of gun  
firmly to side of a  
grounded metal pail. Trig-  
ger gun.  
3. Disengage gun safety latch. Trigger gun and begin  
rolling surface until paint comes to roller.  
Trigger gun briefly only when you need more paint.  
Determine how often you must trigger the gun to  
maintain an even supply of paint to the roller.  
TIꢀꢁꢂꢃAB  
4. Engage trigger lock.  
4. If triggering gun cannot supply enough paint for your  
rolling speed, increase pump pressure.  
ti4218a  
When you stop painting, relieve pressure, page  
3. Elevate roller end of extension tube to prevent  
paint from draining out.  
If you suspect the spray tip or hose is clogged or that  
pressure has not been fully relieved after following the  
steps above, VERY SLOWLY loosen tip guard retaining  
nut or hose end coupling to relieve pressure gradually,  
then loosen completely. Clear hose or tip obstruction.  
5. Flush pump, gun and pressure roller immediately  
after each use to prevent paint from drying in the  
pressure roller and damaging it.  
See Cleaning, page 4.  
311082B  
3
 
 
Cleaning  
Cleaning  
This is the procedure for flushing/cleaning the pressure  
roller. The sprayer and gun you are using may have ad-  
ditional flushing/cleaning instructions; such as cleaning  
filters and screens. See sprayer and gun operation man-  
uals.  
4. Place roller frame (1) in paint pail. Be sure the holes  
in roller frame (1) are facing inside paint pail.  
5. Prime pump with water or flushing fluid for oil-based  
materials. Use the lowest pump pressure setting.  
Leave pressure roller attached to gun for  
this procedure.  
Refer to roller parts drawing, page 5.  
6. Turn prime/spray valve to SPRAY.  
Perform Step 7 at the lowest pressure possible.  
7. Trigger gun until flushing fluid begins to dilute the  
paint.  
1. Relieve pressure, page 3.  
8. Place roller frame (1) in another bucket and con-  
tinue flushing until fluid coming out of roller frame (1)  
is clear.  
2. Remove roller cover (13) and diffuser (23) from  
roller frame (1) as follows:  
9. Shut off pump. Turn prime/spray valve to PRIME.  
a. Using your thumb, press down on clip (5) to  
release end caps (2 & 4), diffuser, (23) and  
roller cover (19) into pail.  
Storage  
If you are going to store the airless equipment for an  
extended period of time after flushing with water-based  
fluid, flush again with Pump Defenderor mineral spir-  
its/paint thinner. Leave the fluid in the system during  
storage.  
b. Remove roller cover (19) from diffuser (23).  
c. Pull end caps (2 & 4) off diffuser (23).  
3. Clean roller cover (19), caps (2 & 4) and diffuser  
(19) with water or a compatible fluid for oil-based  
materials.  
4
311082B  
 
 
Parts  
Parts  
Ref.  
23  
No. Part No.  
Description  
Qty.  
1
2
15B052  
245999  
FRAME, roller  
CAP, end (includes seal and  
retainer)  
CAP, end (includes seal, retainer,  
and o-ring)  
CLIP, roller  
FITTING, swivel  
GASKET  
O-RING  
NUT, retaining  
FITTING, extension, male  
GASKET  
EXTENSION, 20-inch, (50 cm)  
FITTING, extension, female  
LABEL, warning  
ROLLER, cover, 9-inch, 1/2 inch  
(13mm) nap  
1
1
4
1
4
246277  
1
WLꢀꢀꢁꢂE  
5
6
7
8
9
12  
13  
14  
15  
16  
19  
197106  
197118  
162863  
114049  
197117  
704-25G  
15A619  
7422R  
7551G  
195804  
7722  
1
1
2
2
1
1
1
1
1
1
1
5
2
9
19  
6
20  
13  
12  
20  
23  
25  
115524  
15B065  
239531  
GASKET  
1
2
1
DIFFUSER  
UNION, swivel, 45°  
14  
16  
Replacement Danger and Warning labels, tags, and  
cards are available at no cost.  
13  
15  
8
7
25  
7
8
311082B  
5
 
 
ASM Standard Warranty  
ASM Standard Warranty  
ASM warrants all equipment referenced in this document which is manufactured by ASM and bearing its name to be free from defects in material  
and workmanship on the date of sale by an authorized ASM distributor to the original purchaser for use. With the exception of any special,  
extended, or limited warranty published by ASM, ASM will, for a period of twelve months from the date of sale, repair or replace any part of the  
equipment determined by ASM to be defective. This warranty applies only when the equipment is installed, operated and maintained in  
accordance with ASM’s written recommendations.  
This warranty does not cover, and ASM shall not be liable for general wear and tear, or any malfunction damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-ASM component parts. Nor shall ASM be liable for malfunction, damage, or wear caused by the incompatibility of ASM equipment with  
structures, accessories, equipment or materials not supplied by ASM, or the improper design, manufacture, installation, operation or maintenance  
of structures, accessories, equipment or materials not supplied by ASM.  
This warranty is conditioned up the prepaid return of the equipment claimed to be defective to an authorized ASM distributor for verification of the  
claimed defect. If the claimed defect is verified, ASM will repair or replace free of charge any defective parts. The equipment will be returned to the  
original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be  
made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED  
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
ASM’s sole obligation and buyer’s sole remedy for any breach of warranty shall be set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action or breach of warranty must be brought within two (2) years of the date of sale.  
ASM MAKES NOT WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY ASM. These items sold, but not manufactured by ASM (such as electric motors, switches, hose, etc.), are subject to the  
warranty, if any, of their manufacturer. ASM will provide purchaser with reasonable assistance in making any claim for breach of these warranties.  
In no event will ASM be liable for indirect, incidental, special or consequential damages resulting from ASM supplying equipment hereunder, or the  
furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of ASM, or otherwise.  
TO PLACE AN ORDER OR FOR SERVICE, contact your ASM distributor,  
or call 1-800-285-0032.  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
ASM reserves the right to make changes at any time without notice.  
Manufactured by ASM Company; a division of Graco Inc.  
ASM Company, 3500 North 1st Avenue, Sioux Falls, SD 57104  
PRINTED IN U.S.A. 311082  
4/2005, Revised 4/2006  
6
311082B  
 

Haier Microwave Oven EB 3190EGS User Manual
Hamilton Beach Can Opener 840213800 User Manual
HANNspree Flat Panel Television HANNSzsheep User Manual
Harbor Freight Tools Insect Control Equipment 95500 User Manual
Honeywell Thermostat CPFILA User Manual
Hotpoint Dishwasher HDA2000G User Manual
Hotpoint Freezer hm315x f User Manual
HP Hewlett Packard Server rp7420 User Manual
Husqvarna Lawn Mower Z3815BIA Z3815BIA Z4217BIA Z4218KOA Z4218KOA User Manual
Hyundai IT Flat Panel Television HLT 3272 User Manual