Graco Plumbing Product 119577 User Manual

Instructions - Parts List  
24-Gallon (90-Liter)  
310864D  
Oil Ace  
EN  
Pressurized oil drain for collection of used lubricants and anti-freeze.  
Model 119577 Series A  
8 psi (55 kPa, .5 bar) Maximum Working Pressure  
Important Safety Instructions  
Read all warnings and instructions in this manual.  
Save these instructions.  
.
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441  
Copyright 2005, Graco Inc. is registered to I.S. EN ISO 9001  
 
Warnings  
WARNING  
EQUIPMENT MISUSE HAZARD  
Misuse can cause death or serious injury.  
Do not exceed the maximum working pressure or temperature rating of the lowest rated system  
component. See Technical Data in all equipment manuals.  
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all  
equipment manuals. Read fluid and solvent manufacturer’s warnings.  
Check equipment daily. Repair or replace worn or damaged parts immediately.  
Do not alter or modify equipment.  
For professional use only.  
Use equipment only for its intended purpose. Call your Graco distributor for information.  
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.  
Do not use hoses to pull equipment.  
Comply with all applicable safety regulations.  
c
a
b
d
a. Do not drain caustic or flammable products.  
b. Do not expose the tank to any source of heat.  
c. Do not do any welding on the tank.  
d. Keep hands and face protected when draining high temperature oils.  
United States Government safety standards have been adopted under the Occupational Safety and  
Health act. Consult these standards—particularly the General Standards, Part 1910.  
310864D  
3
 
Assembly  
Assembly  
5. Insert the drain tube (H) through threaded opening  
on top of tank and hand-tighten collar (K) on  
threads.  
Numbered panels in FIG. 1 correspond to the fol-  
are referenced throughout this manual.  
6. Connect drain bowl (G) to drain tube (H) and tighten  
screw (J) to secure.  
1. Attach front wheels (A). Assemble wheel (A) on  
axle, then washer and hex-head bolt. Tighten.  
7. Loosen knob (L) and raise or lower drain bowl to  
desired height. Hand-tighten knob (L) to secure  
bowl at desired height  
2. Attach rear casters (B). Insert caster shaft through  
hole in bracket. Assemble washer, lock washer, and  
crown nut. Tighten.  
8. Place filter tray (M) into drain bowl (G).  
3. Insert handle (C) into brackets (D) on back of tank,  
secure with screws provided.  
9. Place plastic funnel extension (N) over drain bowl  
(G).  
4. Place tool tray (E) on tabs of tray bracket (F). Apply  
pressure to seat tray.  
R
E
S
F
C
P
A
D
1, 2  
3, 4  
B
N
O
G
M
J
L
H
K
G
T
5, 6, 7  
8, 9  
FIG. 1: Assembly  
4
310864D  
 
   
Operation  
Operation  
Emptying  
1. To raise or lower the drain bowl (G), loosen knob  
(L), adjust drain tube (H) to desired height, and  
retighten knob (L).  
CAUTION  
To ensure pressurization, adjust the drain tube (H) to  
it’s fully extended position before emptying the tank.  
2. Ensure that the ball valve (O) on the drain tube (H)  
is open (red handle is down), when collecting used  
oil.  
If you should inadvertently attempt to empty the  
tank before you fully extend the drain tube, the tank  
will not pressurize and therefore will not empty.  
CAUTION  
Never fill the tank beyond the maximum level indi-  
cated on the oil level gauge (P) located on the side of  
the tank. Monitor the oil level regularly to ensure you  
do not overfill the tank.  
1. Close ball valve (O) on the drain tube (red handle is  
horizontal).  
2. Remove plug cap from the end of discharge hose  
(R) and place end of hose in a suitable used-oil con-  
tainer.  
3. When the tank is full or nearly full, as indicated on  
oil level gauge (P), it is time to empty the tank.  
3. Open ball valve (S) at the discharge hose connec-  
tion.  
4. Connect 8 psi, (55 kPa, .5 bar) compressed air to  
tank air valve (T).  
5. When the tank is empty, close ball valve (S) and  
open ball valve (O).  
6. The tank is ready for continued use.  
Service  
See page 6 for service/repair kits that are available for  
your Oil Ace pressurized oil drain system. Follow  
assembly instructions on page 4 and part locations indi-  
cated on page 6 to replace parts. To simplify reassem-  
bly, make note of the position and order of worn parts  
when removing them, and assemble new parts in the  
same fashion.  
310864D  
5
 
     
Parts  
Parts  
Ref.  
Qty  
No. Part No. Description  
.
1
119575 O-ring repair kit  
Includes all o-rings (8) for entire  
1
unit. See dashed arrows on parts  
drawing for locations.  
Caster and wheel repair kit  
2
See  
1
Table  
Below  
Includes wheels (2), washers (2),  
bolts (2); casters (2), washers (2),  
lock washers (2), crown nuts (2)  
8
5
3
4
119578 Air valve kit  
Includes “Y” fitting, safety valve,  
tank valve.  
119580 Gauge tube kit  
1
1
2 o-rings  
(Includes gauge tube with incre-  
mentally marked label, elbows (2),  
tube fittings (2)  
119581 Funnel kit  
Includes drain bowl, filter tray  
119582 Discharge hose kit  
7
5
6
1
1
4 o-rings  
Includes tank fitting, 1/2” ball valve,  
discharge hose assembly  
119853 Drain tube kit  
3
7
1
Includes all parts in column  
connecting drain bowl to tank  
119574 EXTENSION, funnel  
195591 LABEL, warning (not shown)  
8
9  
1
1
Replacement Warning labels are available at no  
6
cost.  
4
2 o-rings  
2
2 - Caster and Wheel Repair Kit  
Refer to the following table to determine the correct Caster and Wheel Repair Kit to order for your Oil Ace equipment.  
Caster  
Diameter  
Wheel Bearing  
Inner Diameter  
Part No.  
Date Code  
Wheel Diameter  
Wheel Axel Length  
119576  
Prior to I12A  
(e.g. H12A, or B09A)  
7 inch  
(175 mm)  
4 inch  
(100 mm)  
~1.25 inch  
(32 mm)  
0.64 inch  
(16.25 mm)  
127987  
I12A or later  
(e.g. J12A or I14A)  
6 inch  
(150 mm)  
3 inch  
(75 mm)  
~1.7 inch  
(43 mm)  
0.59 inch  
(15 mm)  
6
310864D  
 
 
Technical Data  
Technical Data  
Maximum working pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 psi (55 kPa, .5 bar)  
Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 in. (61 cm)  
Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 in. (40.6 cm)  
Height  
with drain bowl at lowest adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56.5 in. (143.5 cm)  
with drain bowl at highest adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 in. (203 cm)  
Funnel diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 in. (61 cm)  
Dry weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 lb. (33.6 kg)  
Wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . steel, copper, PVC plastic, rubber, aluminum  
Recommended operating temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30° to 105° F (-1° to 41° C)  
310864D  
7
 
 
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance  
of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will  
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED  
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
MM 310864  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441  
Printed in USA 310864D  
October 2014  
 

Graco Blood Pressure Monitor 3A1331C User Manual
Graham Field Mobility Aid CKD12F7T User Manual
Grizzly Saw G0665 User Manual
Haier Washer HK1007TVE ME User Manual
Harbor Freight Tools Power Hammer 68148 User Manual
Hasselblad Printer FS 3750 User Manual
Honeywell Laptop 6100 Mobile Computer User Manual
HP Hewlett Packard Personal Computer VS803UT User Manual
Husqvarna Lawn Mower 140R User Manual
Husqvarna Pressure Washer 020524 00 3 User Manual