Instructions – Parts List
STAINLESS STEEL, ONE QUART (ONE LITER)
Air Regulated
Pressure Cups
308791E
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
See page 10 for model numbers and maximum
working pressures.
7611A
7612A
Single Air Regulator
Double Air Regulator
Pressure Cup Kit
Part No. 239802 and 245181
Pressure Cup Kit
Part No. 239803
7613A
Remote Single Air Regulator
Pressure Cup Kit
Part No. 239804
Setup
1
2
Push tube (3) fully into elbow fitting (D)
Tapered side of the check valve must face towards the cup’s elbow fitting
E
D
E
D
F
F
1
2
3
1
3
13
2
13
7611A
Part No. 239802 and 245181
Single Air Regulator Pressure Cup Kit
7612A
Part No. 239803
Double Air Regulator Pressure Cup Kit
Fig. 2
Part No. 239804
Remote Single Air Regulator
Pressure Cup Kit
G
19
4
E
J
D
2
1
13
1
2
Push tube (3) fully into elbow fitting (D)
3
Tapered side of the check valve must face
towards the cup’s elbow fitting
H
7623A
Fig. 3
308791
3
Operation
WARNING
Never exceed 20 psi (1.4 bar) static air pressure to
the cup. Exceeding the maximum working pressure
of the cup or any other system component could
cause component rupture, which could result in
serious injury and property damage.
M
A
K
L
WARNING
Pressure Relief Procedure
To reduce the risk of serious injury, including splash-
ing in the eyes or on the skin, always follow this
procedure after you stop spraying, when checking or
servicing any part of the spray system, before dis-
connecting the gun, air regulator, or pressure cup
and when removing a pressure cup for refilling or
cleaning.
7611A
Fig. 4
Spraying Tips
The regulator is not self relieving so if the regulated air
pressure setting is causing excessive fluid flow, follow
these steps.
1. Turn off the air supply to the gun.
2. Trigger the gun into a grounded metal waste
container to relieve fluid pressure.
3. Place the cup on a table and slowly release the
clamp (A) to bleed-off any residual pressure in
the cup. See Fig. 4. Be sure to push the clamp
lever fully to the clamped position before turning
on the air supply to the gun again.
1. Pull up the cup regulator adjustment knob lock-ring
(L). See Fig. 4.
2. Turn the adjustment knob (K) counterclockwise.
3. Trigger the gun into a grounded metal waste
container until cup pressure is lowered.
Setting the Cup Air Pressure
1. Pull up the cup regulator adjustment knob lock-ring
(L); this allows the knob (K) to turn. See Fig. 4.
4. Turn the adjustment knob (K) clockwise until you
obtain the desired lower pressure setting.
2. Set the cup pressure at zero by turning the
adjustment knob (K) fully counterclockwise.
5. Push down the adjustment knob lock-ring (L).
3. Slowly turn the adjustment knob (K) clockwise to
increase the air pressure to the cup.
CAUTION
Do not restrict the fluid flow by continuously spraying
with the gun’s fluid adjustment knob (M) turned in
(clockwise) as this will cause excessive abrasive
wear on the fluid needle and trigger/air valve shaft.
4. Push the adjustment knob lock-ring (L) down to
lock the cup pressure setting.
Setting the Gun Air Pressure
To restrict the fluid flow, lower the cup pressure or use
a smaller size needle/nozzle set and air cap combina-
tion.
NOTE: Installing the gun air inlet regulator adds a
pressure drop that could limit the air cap pressure.
Set the gun air pressure regulator for the minimum
pressure needed to atomize your fluid. See your gun
manual for recommended settings.
If the cup pressure must be below 1.0 psi (0.07 bar) to
achieve the desired fluid flow, a smaller needle/nozzle
size is recommended.
4
308791
Operation
Optional Gun Air Regulator 235119
NOTE:
D Installing the gun air inlet regulator adds a pressure
drop that could limit the air cap pressure.
D See Accessories on page 11 for air regulator
replacement parts.
1. Pull up the gun regulator adjustment knob lock-ring
(L); this allows the knob to turn. See Fig. 5.
2. Set the gun air pressure at zero by turning the
regulator adjustment knob (K) fully counterclock-
wise.
L
3. Turn on the air supply to the gun.
4. Turn the regulator adjustment knob (K) clockwise
to increase the air pressure to the gun.
K
WARNING
Never exceed 100 psi (7 bar) Maximum Working
Air Pressure to the gun. Exceeding the maxi-
mum working pressure of the gun or any other
system component could cause component
rupture, which could result in serious injury and
property damage.
7614A
Fig. 5
5. Push the adjustment knob lock-ring (L) down to
hold the pressure setting.
308791
5
Maintenance
5. If any fluid is in the lid elbow fitting (N), flush it with
Disconnect the Gun and Air Regulator
from the Cup
solvent but do not soak it in solvent for an
extended period.
1. Follow the Pressure Relief Procedure Warning
on page 4.
6. If fluid is in the tubing (3) or check valve (13),
replace them. See the parts list for your cup
assembly to order parts.
2. To disengage the tube grip, push down on the
outer ring of the lid elbow fitting (N), then pull the
tubing (3) out of the fitting. See Fig. 6.
3. Holding a wrench on the gun fluid inlet fitting,
disconnect the pressure cup swivel nut fitting (E).
E
4. Disconnect the air regulator fitting from the gun air
inlet.
N
A
5. Clean the gun as instructed in the gun manual.
101
B
CAUTION
Do not clean the air regulators in a gun washer as it
will damage the regulator diaphragm. Do not use any
cleaning method that allows solvent to enter the
regulator internally.
3
102
Remove the Cup Lid
13
1. Push the clamp lever (A) fully to the unclamped
position, against the yoke (B). See Fig. 6.
C
2. Twist the cup lid (101) counterclockwise to disen-
gage the yoke hook from the cup extended pins
(C).
103
3. Remove the cup lid (101).
4. Clean the cup lid (101) and cup (103).
CAUTION
3668
When cleaning the pressure cup lid (101), avoid
prolonged exposure of the gasket (102) to solvent as
this will cause it to swell.
Fig. 6
6
308791
Parts
Use Only Genuine Graco Parts and Accessories
One Quart Pressure Cup
Single Air Regulator Assembly
Part No. 239801
Part No. 235375, Series B
Part No. 245192
Includes the following parts:
Includes the following parts:
Ref.
No.
Part No. Description
Qty.
101
236908
LID, pressure cup; Includes
Ref.
item 102
GASKET
CUP, 1 quart (1 liter)
1
1
1
No.
Part No. Description
Qty.
102
103
189883
239727
1
2
3
4
5
6
162453
156823
112699
187410
111500
111501
NIPPLE
1
1
1
1
SWIVEL FITTING
TUBE; 1/4 in. OD X 2.38 in.
AIR FITTING
GAUGE; 0-15 psi (0-1 bar) range 1
REGULATOR; 0-12 psi
NOTE: See the Technical Data, page 10, for a list of
pressure cup materials.
(0-0.8 bar) range
1
8
112698
ELBOW FITTING; 90_ swivel;
for 1/4 in. OD tube
NIPPLE
TEE FITTING
PRESSURE RELIEF VALVE
AIR RESTRICTOR
101
102
1
1
1
1
1
9
100168
110440
112059
189557
M71256 CHECK VALVE1
112699
10
11
12
13
14
TUBE, 1/4 in. OD X 2.38 in.
(235735)
TUBE 1/4 in. OD X 6.00 in.
(245192)
1
1
198527
14
1
2
4
103
3
13
11
1
3
01960A
1
9
Single Air Regulator Pressure Cup Kit
Includes the following parts:
1
8
Part No. 239802
1
Part No.
Description
Qty.
235375
Single Air Regulator Assembly
See parts list at right
Pressure Cup Assembly
See parts list above
1
1
239801
195065
1
2
10
12
Air Inlet Fitting
1
1
Part No. 245181
6
5
1
Part No.
Description
Qty.
01728
245192
Single Air Regulator Assembly
See parts list at right
Pressure Cup Assembly
See parts list above
1
2
3
Apply anaerobic pipe sealant (white) to external threads
1
1
Press fit tightly into tee (10)
239801
195065
Tapered side of the check valve must face towards the cup’s
elbow fitting
Air Inlet Fitting
308791
7
Parts
Use Only Genuine Graco Parts and Accessories
Double Air Regulator Pressure Cup Kit
Part No. 239803
Includes the following parts:
Part No.
Description
Qty.
235376
Double Air Regulator Assembly
See parts list below
1
239801
195065
Pressure Cup Assembly
See parts list, page 7
Air Inlet Fitting
1
1
Double Air Regulator Assembly
Part No. 235376, Series B
Includes the following parts:
Ref.
No.
Part No. Description
Qty.
3
3
13
2
3
4
5
6
156823
112699
162453
111500
111501
SWIVEL FITTING
TUBE; nylon; 1/4 in. OD
NIPPLE
GAUGE; 0-15 psi (0-1 bar) range 1
REGULATOR; 0-12 psi
1
2
1
1
2
1
14
11
1
(0-0.8 bar) range
1
1
1
9
8
8
112698
ELBOW FITTING; 90_ swivel;
for 1/4 in. OD tube
NIPPLE
TEE FITTING
PRESSURE RELIEF VALVE
1
1
1
1
1
1
9
100168
110440
112059
189557
10
11
12
13
14
AIR RESTRICTOR
M71256 CHECK VALVE
110436
110438
GAUGE; 0-100 psi
(0-7 bar) range
REGULATOR; 0-100 psi
(0-7 bar) range
1
1
15
15
1
2
10
12
1
4
1
1
6
5
01729A
1
Apply anaerobic pipe sealant (white) to external threads
2
3
Press fit tightly into tee (10)
Tapered side of the check valve must face towards the cup’s
elbow fitting
8
308791
Parts
Use Only Genuine Graco Parts and Accessories
Ref.
No.
Remote Single Air Regulator
Pressure Cup Kit
Part No. Description
Qty.
Part No. 239804
3
4
5
6
172680
172682
111500
111501
ELBOW FITTING
HOSE ADAPTER
GAUGE; 0-15 psi (0-1 bar) range 1
1
1
Includes the following parts:
Part No.
Description
Qty.
REGULATOR; 0-12 psi
236142
Remote Air Regulator Assembly
See parts list below
Pressure Cup Assembly
See parts list, page 7
(0-0.8 bar) range
CONNECTOR; for 1/4 in. OD tube 1
TUBE; nylon; 1/4 in. OD
TEE FITTING
PRESSURE RELIEF VALVE
AIR RESTRICTOR
1
1
1
7
9
112698
112699
110440
112059
189557
239801
2
1
1
1
1
1
10
11
12
13
14
15
M71256 CHECK VALVE
Remote Air Regulator Assembly
Part No. 236142, Series B
Includes the following parts:
103656
212005
HEX NIPPLE
AIR HOSE; buna-n; 1/4 npsm;
6 ft. (1.83 m) long
1
16
212006
FLUID HOSE; nylon; 3/8 npsm;
6.5 ft. (1.98 m) long
MOUNTING BRACKET
PANEL NUT
Ref.
No.
1
1
1
1
Part No. Description
Qty.
17
18
19
188770
112308
183696
1
2
172620
100188
HOOK
HEX NUT
1
1
TEE FITTING
1
5
1
6
17
18
1
1
1
14
11
2
3
4
4
16
2
1
12
19
7
9
15
1
10
3
13
01963A
1
2
3
4
Apply anaerobic pipe sealant (white) to external threads
Tapered side of the check valve must face towards the cup’s
elbow fitting
Press fit tightly into tee (10)
Apply high strength anaerobic pipe sealant (green) to external
threads.
308791
9
Technical Data
Single Air Regulator Pressure Cup Kit, Part No. 239802 and 245181
Maximum Outlet Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 psi (0.8 bar)
Maximum Inlet Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 psi (7 bar)
Double Air Regulator Pressure Cup Kit, Part No. 239803
Cup Regulator Maximum Outlet Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 psi (0.8 bar)
Gun Regulator Maximum Outlet Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 psi (7 bar)
Maximum Inlet Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 psi (7 bar)
Remote Single Air Regulator Pressure Cup Kit, Part No. 239804
Maximum Outlet Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 psi (0.8 bar)
Maximum Inlet Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 psi (7 bar)
One Quart Pressure Cup, Part No. 239801
Maximum Working Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 psi (1.4 bar)
Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 quart (1 liter)
Material
Cup, Tube, Seat, and Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304 Stainless Steel
Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glass–Filled Nylon
Sleeve, Clamp Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electroless Nickel Plated Aluminum
Yoke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electroless Nickel Plated Steel
Cup Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Polyethylene Foam
Cup Fluid Nut Thread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8–18 npsm; R3/8–19 compound thread
Regulator Swivel Nut Thread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4–18 npsm; R1/4–19 compound thread
Weight
Pressure Cup Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 lb. 7 oz. (646 g)
Cup with Single Air Regulator* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 lb. 4 oz. (1007 g)
Cup with Double Air Regulator* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 lb. 8 oz. (1113 g)
Remote Cup with Air Regulator Assembly* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 lb. 9 oz. (1130 g)
Remote Cup with Air Regulator Assembly and Hoses* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 lb. 1 oz. (1816 g)
Gun Air Regulator* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 oz. (224 g)
* Weight without gun
10
308791
Accessories
Spray Gun Air Regulator Assembly 235119
Quick Disconnect Coupler 208536
100 psi (7 bar) Maximum Outlet Pressure
150 psi (10 bar) Maximum Inlet Pressure
1/4 npt(f), zinc-plated brass
NOTE: Installing the coupler adds a pressure drop that
could limit the air cap pressure.
For use on a spray gun with a 1/4–18 npsm air fitting.
Includes the following parts:
Ref.
No.
Part No. Description
Qty.
Quick Disconnect Pin 169970
1
2
3
162453
156823
110436
NIPPLE; 1/4 npt x 1/4 npsm
1
1
1/4 npt(m), zinc-plated steel
SWIVEL UNION; 1/4 npt
GAUGE; 0-100 psi
(0-7 bar) range
REGULATOR; 0-100 psi
(0-7 bar) range
1
1
4
110438
169970
Replaces nipple 162453,
item 1, at left
NOTE: Installing the gun air inlet regulator adds a
pressure drop that could limit the air cap pressure.
208536
3
1
0697
2
One Quart Pressure Cup Liners 112490
Box of 20 special blend polyethylene liners.
Use to line cup for easy clean-up. Graco Standard
Warranty
4
01730
308791
11
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers
to identify the distributor closest to you:
1–800–328–0211 Toll Free
612–623–6921
612–378–3505 Fax
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 308791
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441
Copyright 1977, Graco Inc. is registered to I.S. EN ISO 9001
Revised March 2008
12
308791
|