Failure to follow these warnings and
result in serious injury or death fro
Toddler Bed
OWNER’S MANUAL
Model No. ___________
Serial No. ___________
Dear Customer,
Please fill in the model and
serial numbers above from
the label on the side tube of
your new toddler bed.
Strings can cause strangulation!
DO NOT place items with a string
around a child’s neck, such as
hood strings or pacifier cords. DO
NOT suspend strings over toddler
bed or attach strings to toys.
Model No. 8824
Congratulations on your purchase of a
Graco® toddler bed!
Graco is a leader in juvenile products
designed for your child’s comfort and
convenience. We believe your Graco®
toddler bed is a wise choice, promising
many hours of enjoyment for your child.
Before using your toddler bed, please take
a few minutes to read this Owner’s Manual.
The short time you spend reading these
instructions will help you use your
toddler bed properly.
DO NOT use a water mattress or
all foam mattress with this toddler
bed.
DO NOT place bed
where cords from b
may strangle a chil
fall out of the windo
Please save your Owner’s Manual
for future use.
ALWAYS use a full-size crib mattress, being at least 515/
(131 cm) in length, 271/
in. (69 cm) in width, and 4 in.
(10 cm) in thickness.
8
in.
Customer Satisfaction
4
Our goal is to make every product the best it can
be! We are also committed to supporting our
products after purchase. If you would like to speak
to Graco about your product, please contact our
Customer Service Department at 1-800-345-4109
Our knowledgeable staff will be ready to answer any
questions you may have concerning parts, use or
maintenance. When you call, please have the
model and serial numbers ready so your call
may be processed quickly and efficiently.
DISCONTINUE USE OF THE TODDLER BED when your
child weighs more than 50 pounds (23 kg). Use the bed
with only one child at a time.
USE ONLY bed rails provided by Graco®.
© 2000 Graco 600-4-00 600596
2
Assembling the
Attaching the
Headboard and Footboard
Headboard and Footboard
Step 1.
Step 1.
Legs have a small side hole near
one end. For each leg, push end
with side hole firmly down into
a plastic foot. Side hole must be
covered by foot. It may be
Begin by attaching the frame to
the footboard.
Bumps
Side hole
Stand the footboard at one end
of the metal frame with the
Graco® name facing out and
four plastic “bumps” of the foot-
board facing toward the frame.
necessary to tap foot on a hard
surface to get it all the way on.
Holding the footboard upright,
grasp the two side tubes as
shown and lift carefully. Rest the
ends of the side tubes on the
footboard.
Step 2.
Assemble headboard and long
legs. Push open end of one long
leg onto plastic plug under “knob”
on one side of headboard.
Step 2.
Then push leg sideways so the
rectangular plug on lower side
of headboard goes into hole on
side of the leg.
Insert two T-nuts through the
two holes in the side tubes
and into the footboard tube as
shown. Place the bolts into the
holes on the outside of the
footboard tubes and into the
T-nuts. Tighten bolts with the
enclosed hex wrench.
Bolt
T-nut
Attach other long leg in the
same way to other side of the
headboard.
Hex
wrench
Assemble the footboard and
short legs the same way.
Repeat on other side of the
footboard.
Step 3.
Insert a screw into the lowest
hole on each leg and into the
plastic head- or footboard.
Step 3.
Screw
Attach the headboard in the
same way. It may be attached
with either side facing the bed.
The toddler bed will look like
illustration.
Tighten screw securely with the
included hex wrench, but do
not over-tighten.
Repeat for other three legs.
After both endboards have been
attached to the frame, use the
enclosed hex wrench to FIRMLY
TIGHTEN all eight bolts into
their T-nuts.
CHECK that all four legs are
securely attached to the
head- and footboards by
pulling on the legs.
Hex
wrench
Assembling the Frame
Attaching the Mattress Retainers
Step 1.
Do not use toddler bed without
Line up the side tubes and
crossbars on the floor as shown
at right. It may be helpful to
brace one side tube against
a wall or stationary object.
Holes in side tubes must face
each other.
mattress retainers. Mattress may slide.
Step 1.
Snap the mattress retainers onto
Ribs
the center of the side tubes. The
ribs of each retainer should face
the inside of the bed frame. Line
up the holes of the mattress
retainers with the small holes
in the side tubes.
Step 2.
Insert ends of the crossbars
into holes in the side tubes.
600-4-00 600596
5
6
Hex wrench
Step 2.
Replacement Parts
Fasten each mattress retainer
to side tubes with one T-nut
and bolt. The T-nut must be
on the inside of the frame.
Tighten the bolts and T-nuts
with the hex wrench provided.
Instructions for ordering toddler bed parts:
Complete form below. Your toddler bed model number
MUST be included on the form to ensure proper
replacement parts. Your model number can be found
on the label on the side tube of your toddler bed.
Payment must accompany your order.
Bolt
T-nut
Fold edges
down
Step 3.
Parts List:
Price:*
Position mattress support with
printed side up as shown. Fold
edges down at creases, and
place on bed so notches in
edges fit over the crossbars.
Side tube.................................. $ 8.00 (each)
Crossbar...................................$ 5.00 (each)
Long leg....................................$ 7.00 (each)
Short leg...................................$ 5.00 (each)
Foot.......................................... $ 5.00 (set of 4)
Hardware..................................$ 5.00
Mattress support.......................$10.00
Mattress retainer.......................$ 5.00 (each)
Headboard................................$12.00
Footboard.................................$12.00
Left bed rail (as seen from
Attaching the Bed Rails
Step 1.
There are left and right bed rails.
When installed correctly, the note
on the bed rails, “THIS SIDE
MUST FACE MATTRESS,” will
be to the inside of the bed.
behind headboard)...............$10.00
Right bed rail (as seen from
behind headboard)...............$10.00
* Prices subject to change without notice.
IF YOU NEED HELP
If you have any questions or if you need
any part not listed, please call toll-free:
1-800-345-4109
Snap bed rails on bed side
tubes as shown.
Step 2.
Return the form below with payment to:
GRACO CHILDREN’S PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 100, MAIN STREET
Lift bed rails and slide them to
the inside of the headboard.
Snap to headboard as shown.
Mattress retainer will fit in the
recessed area in the bed rails.
ELVERSON, PA 19520
Model No. (required)
Be sure bed
rails are secure. Bed rails must
be attached to headboard on
the inside of the post.
SHIPTO:
Name
Serial No. (required)
Address
Side tube
Step 3.
Crossbar
Long leg
Short leg
Foot
Repeat on other side. Both bed
rails must be used. Do not rely
on wall to keep child in bed. See
warnings.
City, State, Zip
(
)
Hardware
Telephone
Mattress support
Mattress retainer
Headboard
Footboard
Left bed rail
Right bed rail
Check enclosed
(payable to Graco Children’s
Products Inc.)
Finishing Assembly
Place a standard full-size crib
Charge to credit card:
Visa
mattress—at least 515/
8
inches
(131 cm) long by 271/
4
inches
MasterCard
Discover
(69 cm) wide by 4 inches (10 cm)
thick—on toddler bed frame.
Subtotal:
Shipping
Mattress
retainer
Account #:
& handling*:
$5.00
The mattress must be placed so the two mattress retainers
on the frame are outside the mattress to keep it from moving.
6% sales tax
(PA only):
Expiration date:
Signature:
Your toddler bed is now ready to use.
Total:
REMINDER: Regularly inspect the toddler bed for damaged
hardware, loose joints, missing parts, or sharp edges.
*$15.00 outside the continental U.S.
7
8
|