Graco Webcam 24H253 User Manual

Instructions/Parts  
24H253 USB  
Module Kit  
3A1333A  
ENG  
®
To add a USB Module to a ProMix 2KE Electronic Proportioner. For professional use only.  
Important Safety Instructions  
Read all warnings and instructions in this  
manual and in your separate ProMix 2KE  
manuals. Save these instructions.  
Kit Parts  
Ref. Part  
Description  
Qty.  
340 16F358 USB MODULE with TOKEN (T);  
see manual 3A1244 for token  
instructions  
341 121417 SCREW  
342 102063 WASHER  
1
4
1
1
1
1
1
343 195875 SCREW  
345 24H084 USB HARNESS  
346 15R325 COVER, bulkhead  
34715X214 LABEL, warning  
Replacement Danger and Warning labels, tags, and  
cards are available at no cost.  
NOTE: You must order a CAN cable separately to com-  
plete the installation:  
For systems approved for Hazardous locations (IS,  
alternator powered), order Part No. 15V782 Cable.  
For systems approved for non-Hazardous locations,  
(non-IS) order Part No. 15V778 Cable.  
 
Warnings  
Install the USB Module  
4. Install the USB cable (345) through the side of the  
control box and secure with the bulkhead nut (N,  
included). Connect the other end of the cable to the  
USB port on the module.  
1. Disconnect main power. Open the control box.  
5. Install the bulkhead cover (346) over the USB cable  
port.  
2. Remove the five knockouts (K) on the top of the con-  
trol box. See FIG. 1.  
6. Place the warning label (347) above the USB cable  
port as shown in FIG. 1.  
3. Install the USB module using four screws (341). The  
fifth screw (343) and star washer (342) must be  
installed in the center knockout to provide a ground-  
ing contact to the control box.  
343  
(GND)  
342  
341  
K (5)  
347  
345  
N
T
C
346  
340  
345  
ti16427a  
FIG. 1. Install USB Module  
3A1333A  
3
 
 
Warnings  
Install the Power CAN Cable  
Non-IS Systems  
IS Systems  
1. Remove the user interface cable from J8 of the fluid  
control module and plug it into connector P3 of the  
USB module. See FIG. 2.  
1. Connect Part No. 15V782 Cable (order separately)  
to J2 of the alternator module and to connector P3  
of the USB module. See FIG. 3.  
2. Connect Part No. 15V778 Cable (order separately)  
to J8 of the fluid control module and to connector P4  
of the USB module.  
2. Close the Control Box. Restore power.  
3. See your ProMix 2KE Operation manual for instruc-  
tions on using the USB module.  
3. Close the Control Box. Restore power.  
4. See your ProMix 2KE Operation manual for instruc-  
tions on using the USB module.  
To help prevent fire and explosion, do not connect,  
download, or remove the USB flash drive unless the  
unit is removed from the hazardous (explosive  
atmosphere) location. Never leave the USB flash  
drive in the USB port.  
USB Module  
USB Module  
Alternator Module  
TI16580a  
P4  
P3  
Fluid Control Module  
TI16580a  
P3  
J8  
TI15710a  
J2  
FIG. 3. Install Part No. 15V782 Cable (IS Systems)  
TI16579a  
FIG. 2. Install Part No. 15V778 Cable (Non-IS  
Systems)  
4
3A1333A  
 
   
Warnings  
3A1333A  
5
 
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or  
maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will  
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED  
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
Original instructions. This manual contains English. MM 3A1333  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441  
Copyright 2010, Graco Inc. is registered to ISO 9001  
 

Greenheck Fan Ventilation Hood EM 30 Series User Manual
Grizzly Planer G0453 User Manual
Harbor Freight Tools Paint Sprayer 91009 User Manual
Honeywell Cell Phone Accessories 7845GSMR User Manual
Honeywell Frozen Dessert Maker 5080 User Manual
Hotpoint Cooktop 6512 User Manual
HP Hewlett Packard Electric Heater 11744195 User Manual
HP Hewlett Packard Printer 1150 Series User Manual
IBM Computer Monitor 560 User Manual
Image Treadmill IMTL11997 User Manual