MODEL H8097
2 Ton
Aluminum Jack
Specifications
Maximum Lifting Capacity .....................4000 lbs.
Lifting Range ..........................................4"–171⁄4
Weight .......................................................38 lbs.
"
Failure to follow these instructions could
result in serious personal injury or death:
1. DO NOT overload this jack beyond its
rated capacity. Overloading can cause
the jack to collapse and drop the load.
2. ALWAYS support the vehicle with
appropriately rated support stands
before working under it.
Jack Handle
3. DO NOT attempt to move the vehicle
while the jack is in use.
4. Use only on hard level surfaces like
concrete or asphalt. Other surfaces are
potentially unstable.
5. Center the load on the jack to maintain
proper balance and stability.
6. DO NOT use jack if it begins leaking
fluid or if it sinks when placed under
load. These are indications that the jack
needs to be immediately serviced.
Machine
Label
Saddle
If you need help with the Model H8097, call our
Technical Support line at: (570) 546-9663.
Figure 1. Model H8097 Identification.
Operation
To raise the saddle:
Turn the handle clockwise as far as it will turn
and pump the handle up and down. Turning the
handle clockwise will close the release valve.
To lower the saddle:
Slowly turn the jack handle counterclockwise.
COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JC8828 PRINTED IN CHINA
H8097 Parts Breakdown
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
�
��
�
��
��
��
�
��
��
��
��
��
��
��
��
�
��
��
�
��
��
�
�
��
�
�
��
��
�
��
�
��
��
��
��
��
�
��
��
��
�
�
�
The machine label warns about hazards and ways to prevent injury. The owner of the jack MUST maintain
the original location and readability of the label. If the label is removed or becomes unreadable, contact
H8097 Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PH8097001
PW04M
FLANGE BOLT M10-1.5 X 25
FLAT WASHER 10MM
LINK ROD AXIS
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
PB07M
HEX BOLT M8-1.25 X 25
FRONT ROLLER
FRAME
2
PH8097029
PH8097030
PH8097031
PR06M
3
PH8097003
PR39M
4
EXT RETAINING RING 8MM
SPECIAL WASHER 8MM
FLAT WASHER 8MM
LOCK NUT M20-1.5
HANDLE BAR
5
PH8097005
PW01M
EXT RETAINING RING 16MM
LINK ROD
6
PH8097033
PH8097034
PH8097035
PH8097036
PH8097037
PH8097038
PH8097039
PH8097040
PH8097041
PH8097042
PH8097043
PN01M
7
PH8097007
PR08M
LINK ROD SLEEVE
LONG SADDLE AXIS
SPRING
8
EXT RETAINING RING 19MM
REAR WHEEL SET
9
PH8097009
PH8097010
PH8097011
PH8097012
PLN09M
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
REAR WHEEL SADDLE
HOLDER AXIS
SHORT SADDLE AXIS
LIFT ARM
DOUBLE PISTON PRESS WHEEL
LOCK NUT M12-1.75
FLANGE BOLT M8-1.25 X 25
RUBBER SADDLE PAD
SCREW BUSHING
SADDLE BASE
NYLON WASHER
SADDLE
PH8097014
PH8097015
PH8097016
PH8097017
PH8097018
PH8097019
PH8097020
PH8097021
PSBS18M
PH8097023
PH8097024
PH8097025
PH8097026
PH8097027
EYE BOLT M6-1 X 18
EYE BOLT M6 -1 X 40
HEX NUT M6-1
HANDLE BASE
PRESS WHEEL SHAFT
HANDLE BASE SPECIAL SCREW
LOWER HANDLE
PH8097045
PH8097046
PH8097047
PW04M
SPECIAL NUT 3 X 14MM
AXIS
SPECIAL WASHER 10MM
FLAT WASHER 10MM
SOCKET SHAFT
HAIR PIN COTTER PIN
FLAT WASHER 16MM
OIL FILL PLUG
JOINT CONNECTOR
BUTTON HD CAP SCR M6-1 X 18
UPPER HANDLE
PH8097049
PH8097050
PW08M
PUMP ASSEMBLY
RAISE ARM AXIS
PH8097052
PH8097053
PH8097054
PULL ROD AXIS
FILL PLUG WASHER
MACHINE LABEL
PULL ROD
|