MODEL H8124
7.2 MINI GRINDER KIT
INSTRUCTION MANUAL
COPYRIGHT © JANUARY, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TS8719 PRINTED IN CHINA
Table of Contents
SECTION 1: SAFETY.......................................................................................................2
Safety Instructions for Machinery ...............................................................................2
Additional Safety Instructions for Mini Grinder ...........................................................4
Additional Safety Instructions for Batteries and Chargers..........................................5
SECTION 2: INTRODUCTION .........................................................................................6
Foreword.....................................................................................................................6
Contact Information ....................................................................................................6
Machine Data .............................................................................................................6
SECTION 3: INVENTORY................................................................................................7
SECTION 4: OPERATIONS.............................................................................................8
Charging the Battery...................................................................................................8
Using the LED Gooseneck Work Light.......................................................................9
Installing Bits ..............................................................................................................9
Using the Grinder .....................................................................................................10
High Speed Uses......................................................................................................10
Low Speed Uses ......................................................................................................10
Daily Maintenance ....................................................................................................10
SECTION 5: PARTS LIST..............................................................................................11
WARRANTY AND RETURNS........................................................................................12
SECTION 1: SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazard-
ous conditions. This manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. The
progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
Indicates an imminently hazardous situation which,
if not avoided, WILL result in death or serious
injury.
Indicates a potentially hazardous situation which,
if not avoided, COULD result in death or serious
injury.
Indicates a potentially hazardous situation which,
if not avoided, MAY result in minor or moderate
injury. It may also be used to alert against unsafe
practices.
This symbol is used to alert the user to useful
information about proper operation of the equip-
ment.
Safety Instructions for Machinery
1. READ THROUGH THE ENTIRE
MANUAL BEFORE STARTING
4. ALWAYS
USE
HEARING
PROTECTION WHEN OPERATING
MACHINERY. Machinery noise can
cause permanent hearing damage.
MACHINERY. Machinery presents
serious injury hazards to untrained
users.
5. WEAR PROPER APPAREL. DO
NOT wear loose clothing, gloves,
neckties, rings, or jewelry which may
get caught in moving parts. Wear
protective hair covering to contain
long hair and wear non-slip foot-
wear.
2. ALWAYS USE ANSI APPROVED
SAFETYGLASSES WHENOPERATING
MACHINERY. Everyday eyeglasses
only have impact resistant lenses,
they are NOT safety glasses.
3. ALWAYS
WEAR
A
NIOSH
APPROVED RESPIRATOR WHEN
OPERATING MACHINERY THAT
PRODUCES DUST. Wood dust is
a carcinogen and can cause cancer
and severe respiratory illnesses.
6. NEVER OPERATE MACHINERY
WHEN TIRED, OR UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL. Be mentally alert at all
times when running machinery.
-2-
Model H8124 7.2V Mini Grinder Kit
7. ONLYALLOWTRAINEDANDPROP-
ERLY SUPERVISED PERSONNEL
TO OPERATE MACHINERY. Make
sure operation instructions are safe
and clearly understood.
16. REMOVE ADJUSTING KEYS AND
WRENCHES. Make a habit of check-
ing for keys and adjusting wrenches
before turning machinery ON.
17. CHECK FOR DAMAGED PARTS
BEFORE USING MACHINERY. Check
for binding and alignment of parts,
broken parts, part mounting, loose
bolts, and any other conditions that
may affect machine operation. Repair
or replace damaged parts.
8. KEEP CHILDREN AND VISITORS
AWAY. Keep all children and visitors
a safe distance from the work area.
9. MAKE WORKSHOP CHILD PROOF.
Use padlocks, master switches, and
remove switch keys.
18. USE RECOMMENDED ACCESSORIES
.
10. NEVER LEAVE WHEN MACHINE IS
RUNNING. Turn power OFF and allow
all moving parts to come to a complete
stop before leaving machine unat-
tended.
Refer to the instruction manual for
recommended accessories. The use
of improper accessories may cause
risk of injury.
19. DO NOT FORCE MACHINERY. Work
at the speed for which the machine or
accessory was designed.
11. DO NOT USE IN DANGEROUS
ENVIRONMENTS. DO NOT use
machinery in damp, wet locations,
or where any flammable or noxious
fumes may exist.
20. SECURE WORKPIECE. Use clamps
or a vise to hold the workpiece when
practical. A secured workpiece pro-
tects your hands and frees both hands
to operate the machine.
12. KEEP WORK AREA CLEAN AND
WELL LIT. Clutter and dark shadows
may cause accidents.
21. DO NOT OVERREACH. Keep proper
13. USE A GROUNDED EXTENSION
CORD RATED FOR THE MACHINE
AMPERAGE. Undersized cords over-
heat and lose power. Replace exten-
sion cords if they become damaged.
DO NOT use extension cords for 220V
machinery.
footing and balance at all times.
22. MANY MACHINES WILL EJECT
THE WORKPIECE TOWARD THE
OPERATOR. Know and avoid condi-
tions that cause the workpiece to
"kickback."
14. ALWAYS DISCONNECT FROM POWER
23. BE AWARE THAT CERTAIN WOODS
MAY CAUSE AN ALLERGIC REAC-
TION in people and animals, especial-
ly when exposed to fine dust. Make
sure you know what type of wood dust
you will be exposed to and always
wear an approved respirator.
SOURCE
BEFORE
SERVICING
MACHINERY. Make sure switch is in
OFF position before reconnecting.
15. MAINTAIN MACHINERY WITH CARE
.
Keep blades sharp and clean for
best and safest performance. Follow
instructions for lubricating and chang-
ing accessories.
Model H8124 7.2V Mini Grinder Kit
-3-
Additional Safety Instructions for Mini Grinder
6. SHARP SURFACES. DO NOT place
hands near the tooling surfaces of the
grinder when in operation.
1. READ THIS MANUAL. This manual
contains proper operating instructions
for this grinder.
7. DISCONNECT POWER. Always remove
the battery before making any adjust-
ment, changing tools, or performing
any maintenance to the grinder.
2. OPERATION. DO NOT force the
grinder against the workpiece. Firmly
grasp the grinder and ease it against
the workpiece using light pressure.
8. MACHINE INSPECTIONS. Perform
machine inspections and maintenance
service as required.
3. WORK AREA CONDITIONS. DO
NOT use this grinder in a damp or wet
location. Keep work area well lit. Do
NOT use in the presence of flammable
gases or liquids.
9. FLEX SHAFT. DO NOT use the flex
shaft with a tight bend. This may
cause binding and damage the inner
spindle.
4. GRINDER DESIGN. DO NOT force
this tool beyond its capabilities. DO
NOT modify this tool and do not use
this grinder for any purpose for which
it was not intended.
10. CLAMP THE WORKPIECE. DO NOT
hold the workpiece with one hand and
operate the grinder with the other.
5. AVOID UNINTENTIONAL STARTING
.
11. ATTEND TO YOUR GRINDER. Never
walk away from the grinder and leave
the tool running.
Be sure the switch is in the OFF
position when not in use and before
plugging it in. DO NOT carry any tool
with your hand on the power switch,
whether it is energized or not.
12. TEST RUN. Always test run the grind-
er before starting any work.
Like all machinery there is poten-
tial danger when operating this
machine. Accidents are frequent-
ly caused by lack of familiarity or
failure to pay attention. Use this
machine with respect and caution
to lessen the possibility of operator
injury. If normal safety precautions
are overlooked or ignored, serious
personal injury may occur.
No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individual
working conditions. Use this mini
grinder and other machinery with
caution and respect. Failure to do so
could result in serious personal inju-
ry, damage to equipment, or poor
work results.
-4-
Model H8124 7.2V Mini Grinder Kit
Additional Safety Instructions for
Batteries and Chargers
1. CHARGING EQUIPMENT. Only charge
5. CHARGER DAMAGE. Replace char-
using the charger and batteries sup-
plied with your grinder. DO NOT use
batteries or charges from other cord-
less tools.
ger if it has been dropped, damaged,
or received a hard impact. Repair cord
immediately if damaged.
6. SHORTING BATTERY. Avoid touch-
ing both battery terminals simultane-
ously with skin to prevent injury from
an electrical shock, or metal to prevent
a fire from a spark. Storing the battery
in a box of screws or nails can cause
fire from a spark.
2. CHARGING ENVIRONMENT. Charge
battery on a dry, hard surface in a
shaded location with good ventila-
tion. DO NOT place charger on or
near flammable materials. DO NOT
cover the charger when charging.
Only charge the battery when the
temperature is between 50°F–104°F
(10°C–40°C). Charging in tempera-
ture beyond these extremes will dam-
age the battery.
7. CORD LOCATION. Prevent tripping
over the cord by placing charger close
to the power supply. Avoid using an
extension cord.
3. CHARGER
VOLTAGE.
ONLY
8. DISCONNECT CHARGER. Unplug
the charger when cleaning, or when
not in use.
plug into a circuit that is 110-120V.
Connecting into 220V will damage the
charger, possibly causing a fire or an
explosion. DO NOT charge from a DC
power supply or a generator.
9. BATTERY DISPOSAL. The battery
must be recycled or disposed of prop-
erly. DO NOT dispose of the battery
in a landfill or incinerate. Combustion
of some of the batteries' component
materials can cause toxic fumes and
possible explosion.
4. CORD CARE. Keep cord away from
heat, oil, and sharp objects. DO NOT
carry the charger by the cord, or pull-
the cord to unplug the charger.
Model H8124 7.2V Mini Grinder Kit
-5-
SECTION 2: INTRODUCTION
Foreword
Contact Information
We are proud to offer the Grizzly Model
H8124 7.2V Mini Grinder Kit. This model
is part of a growing Grizzly family of fine
power tools. When used according to the
guidelines set forth in this manual, you
can expect years of trouble-free, enjoyable
operation and proof of Grizzly’s commit-
ment to customer satisfaction.
If you have any comments regarding this
manual, please write to us at the following
address:
Grizzly Industrial, Inc.
C/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
E-Mail: [email protected]
It is our pleasure to provide this manual
with the Model H8124. It was written to
encourage safety and to guide you through
general operating procedures and main-
tenance.
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
The specifications, details, and photo-
graphs in this manual represent the Model
H8124 as supplied when the manual was
prepared. However, owing to Grizzly’s pol-
icy of continuous improvement, changes
may be made at any time with no obliga-
tion on the part of Grizzly.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
Machine Data
Dimensions..............................71/2"L x 2"W
Housing Construction.. High Impact Plastic
Spindle & Collet Construction ............ Steel
Collet ................................................. Brass
Chuck Body Construction... Stainless Steel
Power Required...... 7.2VDC NiCad Battery
Battery Recharger .......... 120VAC to 9VDC
Low Speed ............................... 8,000 RPM
High Speed............................. 16,000 RPM
LED Power Source. 7.2VDC NiCad Battery
Weight of Grinder .......................... 101/2 oz.
Total Weight With Case .....................3 lbs.
-6-
Model H8124 7.2V Mini Grinder Kit
SECTION 3: INVENTORY
Your Model H8124 was carefully packed when it left our warehouse. If you discover the
Model H8124 is damaged after you have signed for delivery, please call Customer Service
immediately at (570) 546-9663 for advice.
Save the containers and all packing materials for possible inspection by the carrier or its
agent. Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condition of the shipment, you should inventory
the equipment.
The setup and operation instructions will be easier to understand if you first become famil-
iar with the components of the Model H8124 7.2V Mini Grinder Kit. Match the letters in
Figure 1 with the inventory list below to identify each of the components that were shipped
with your Model H8124.
C
D
B
A
E
H
F
G
B
J
K
I
Figure 1. Model H8124 inventory
H. 7.2V Mini Grinder with Battery
I. Accessory Kit
4-Piece Sanding Drum Set
A. Collets
B. 10-Piece Mounted Stone Set
C. AC/DC Adapter
•
D. Carrying Case
E. 7.2V NiCad Battery
•
•
2-Piece Buffing Wheel Set
Square Stone Dresser
F. Battery Charger With Gooseneck LED
G. Sanding Disc Set
J. Collet Nut Wrench
K. Assorted Bits
Model H8124 7.2V Mini Grinder Kit
-7-
SECTION 4: OPERATIONS
5. Plug the AC/DC adapter into a 110-
120V power outlet.
—The green light on the battery char-
ger will light when the battery char-
ger is receiving power.
—The red light on the battery charger
will light when a mounted battery is
charging.
Read the manual before operation.
Become familiar with this machine, its
safety instructions, and its operation
before beginning any work. Serious
6. After 3–31⁄2 hours in the energized char-
ger, the battery will be fully charged.
Remove the battery from the charger
and unplug the AC/DC adapter.
personal injury may result if safety or
operational information is not under-
stood or followed.
Note: DO NOT leave the battery in
the energized charger indefinitely. The
charger will NOT turn OFF automati-
cally.
Charging the Battery
To prevent potential problems during ship-
ment, batteries are shipped with little or no
charge. You must charge your new batter-
ies before initial use.
DO NOT leave the battery in the
energized battery charger indefinite-
Note: The time needed to fully charge a
ly. Overcharging the battery could
lead to overheating both the battery
and charger possibly resulting in
a fire.
battery is approximately 3–31⁄2 hours.
To charge the battery:
1. Make sure the AC/DC adapter is not
connected to a power supply.
Make sure the grinder switch is
turned OFF before installing the
battery. Failure to heed this warn-
ing could result in serious personal
injury.
2. Connect the battery charger to the AC/
DC adapter.
3. Press the two side tabs on the battery
and slide the battery from the grinder.
To install the battery into the grinder:
4. Align the arrows on the battery with
the arrows on the battery charger and
press the battery into the battery char-
ger until it snaps into place.
1. Align the arrows on the battery with the
arrows on the grinder base.
2. Press the battery into the grinder until it
snaps into place.
-8-
Model H8124 7.2V Mini Grinder Kit
to install a bit
Using the LED Gooseneck Work
Light
The LED gooseneck work light is a hands-
free solution to illuminating low light opera-
tions.
DO NOT use bits or cutters with a
cutting diameter larger than 1". The
bit or cutter could break apart under
the stresses of high speed use caus-
ing serious personal injury.
To use the LED gooseneck work light:
To install a bit:
1. DISCONNECT
THE
BATTERY
CHARGER FROM THE AC/DC
ADAPTER!
1. REMOVE THE BATTERY FROM THE
GRINDER!
2. Mount a charged 7.2 NiCad battery into
the battery charger (see Figure 2).
2. Depress the collet lock (see Figure 3)
and loosen the collet nut with the collet
wrench. The collet lock will engage as
the collet rotates.
3. Use the small switch on the battery
charger to turn the LED gooseneck
work light ON and OFF.
Note: It is not necessary to com-
pletely remove the collet nut from the
shaft unless you are also changing the
collet.
LED Light
Collet Nut
Switch
Collet Lock
Figure 2. LED gooseneck work light with
battery installed.
Installing Bits
Figure 3. Collet lock.
The Model H8124 uses bits and cutters
1
with a 3⁄32" or a
⁄8" diameter shaft. See
1
3. Insert at least
⁄2" of the bit into the
the Grizzly catalog or www.grizzly.com
for a complete listing of available bits and
accessories.
collet.
4. Hand tighten the collet nut while
depressing the collet lock. Then, use
the collet wrench to tighten the collet
nut an additional 1⁄3 turn.
Model H8124 7.2V Mini Grinder Kit
-9-
High Speed Uses
The high speed setting is best for gen-
eral carving, cutting, routing, and grinding.
The bit removes material more quickly at
higher speed.
Failure to wear ANSI approved safety
glasses while operating the grinder
could cause serious personal eye
injury.
Low Speed Uses
Using the Grinder
The lower speed setting is best for grind-
ing and cutting materials that have low
melting points. Plastics, in particular, often
melt from the heat of friction generated at
higher speeds. The low speed is also best
for polishing and buffing when using the
felt accessories included.
Most operations performed with the Model
H8124 will give the best results at the high
speed setting. However, the low speed
setting is ideal when working with plastics
or other materials that melt easily.
Always test the bit and speed combination
on a scrap piece of material similar to the
workpiece. Trail and error is the best way
to determine the ideal setup.
Use the low speed setting to reduce
friction when working with plastics
or other materials with low melt-
ing points. Some materials can liq-
uefy from the heat of friction and be
thrown into the operator, causing
personal injury.
To use the grinder:
1. Make sure the battery is charged and
properly inserted into the grinder.
2. Grasp the grinder with a secure grip.
3. Turn the grinder ON by moving the
Daily Maintenance
switch to LO or HI.
These procedures should be done after
each use:
—The grinder speed at the LO setting
is 8,000 RPM.
•
•
Wipe the motor housing and tool bits
with a dry cloth, or blow off the dust and
debris with compressed air.
—The grinder speed at the HI setting is
16,000 RPM.
Check for damage to bits, cords, hous-
ing, or other accessories.
4. Ease the working end of the bit against
the workpiece with a light but steady
pressure.
5. To turn the grinder OFF, move the
switch to the OFF position.
-10-
Model H8124 7.2V Mini Grinder Kit
SECTION 5: PARTS LIST
4
5
3
2
1
6
16
18
7
12
9
13
8
10
11
14
19
17
15
23
20
21
24
22
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
8
PH8124001 CARRYING CASE
PH8124002 SANDING DISC SET
PH8124003 ACCESSORY KIT
PH8124004 MOUNTED STONE SET
PH8124005 ASSORTED BIT SET
PH8124006 COLLET NUT WRENCH
PH8124007 COLLET SHIELD
PH8124008 COLLET LOCK
13
14
15
16
17
18
19
20
21
22
23
24
PH8124013 COLLET 1/8"
PH8124014 TAP SCREW 2 X 5
PH8124015 SWITCH COVER
PH8124016 COLLET NUT
PH8124017 GRINDER MOTOR/SPINDLE ASSY
PH8124018 HOUSING BACK HALF
PH8124019 TAP SCREW 3 X 12
PH8124020 AC/DC ADAPTER 120VAC/9VDC
PH8124019 TAP SCREW 3 X 12
PH8124022 BATTERY CHARGER BASE
PH8124023 BATTERY CHARGER/LED ASSY
PH8124024 7.2V NI-CAD BATTERY
9
PH8124009 SPRING
10
11
12
PH8124010 RETAINING RING
PH8124011 HOUSING FRONT HALF
PH8124012 COLLET 3/32"
Model H8124 7.2V Mini Grinder Kit
-11-
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of
maintenance. This is Grizzly’s sole written warranty and any and all warranties that may
be implied by law, including any merchantability or fitness, for any particular purpose, are
hereby limited to the duration of this written warranty. We do not warrant or represent that
the merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they
constantly strive to achieve better quality equipment. We make every effort to ensure that
our products meet high quality and durability standards and we hope you never need to
use this warranty.
Please feel free to write or call us if you have any questions about the machine or the
manual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
-12-
Model H8124 7.2V Mini Grinder Kit
WARRANTY CARD
Name_________________________________________________________________
Street_________________________________________________________________
City _______________________ State_________________________ Zip _________
Phone #____________________ Email ________________________ Invoice #_____
Model # ____________________ Order #_______________________ Serial #______
The following information is given on a voluntary basis. It will be used for marketing purposes to
help us develop better products and services. All information is strictly confidential.
1. How did you learn about us?
____Advertisement
____Friend
____Catalog
____Card Deck
____Website
Other:________________________
2. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Handy
____ Home Shop Machinist ____ Precision Shooter
____ Journal of Light Cont. ____ Projects in Metal
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking ____ Wooden Boat
____ Practical Homeowner ____ Woodshop News
____ Today’s Homeowner
____ Wood
____ Woodsmith
____ Woodwork
____ Live Steam
____ Model Airplane News ____ Rifle
____ Modeltec
____ Old House Journal
____ RC Modeler
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Shop Notes
____ Shotgun News
3. What is your annual household income?
____$20,000-$29,000
____$30,000-$39,000
____$40,000-$49,000
____$70,000+
____$50,000-$59,000
____$60,000-$69,000
4. What is your age group?
____20-29
____30-39
____60-69
____40-49
____70+
____50-59
5. How long have you been a woodworker/metalworker?
____0-2 Years ____2-8 Years ____8-20 Years
____20+ Years
6. How many of your machines or tools are Grizzly?
____0-2 ____3-5 ____6-9
____10+
____No
____No
7. Do you think your machine represents a good value? ____Yes
8. Would you recommend Grizzly Industrial to a friend? ____Yes
9. Would you allow us to use your name as a reference for our customers in your area?
Note: We never use names more than 3 times. ____Yes ____No
10. Comments:_________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
|