MODEL T10157
OAK WORKBENCH
INSTRUCTIONS
NOTICE
If you cannot find an item on the inventory
parts list, check the mounting location on
the workbench or examine the packaging
materials carefully. Some items are pre-
installed for shipping purposes.
Assembly
Tools Needed
Qty
phillips screwdriver #2 ...................................... 1
1
Wrench or socket ⁄2" ........................................ 1
figure 1. Model t10157 oak Workbench.
To assemble your workbench:
features
•
•
•
•
solid oak top (11⁄2" thick) with double rows of
bench dog holes for each vise.
two storage drawers (with ball bearing slides)
that are 14" wide x 133⁄4" long x 21⁄4" deep.
sturdy adjustable steel legs with leveling foot
pads.
two oak-faced vises with removable top plate
and 4" leadscrew travel, 13" wide x 2" thick.
Four bench dogs.
1. insert the four M8 x 30 screw anchors into
the holes at the ends of the front and back
drawer panels for both drawers, as shown in
figure 2.
M4 x 30
Wood screws
•
•
all wood surfaces finished with durable lac-
quer.
•
•
overall dimensions: 62" wide x 30" in depth x
32"–39" tall.
Weight: 155 lbs.
M8 x 30
screw anchors
Inventory
use the parts breakdown and listing on page 4 to
perform an inventory of the shipment.
figure 2. attaching drawer side panels.
if any nonproprietary parts are missing (e.g. a
bolt or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Copyright © oCtoBEr, 2008 By grizzly industrial, inC.
WARNINg: NO pORTION Of THIS MANUAL MAy BE REpRODUCED IN ANy SHApE
OR fORM WITHOUT THE WRITTEN AppROvAL Of gRIzzLy INDUSTRIAL, INC.
#ts11313 printEd in China
8. insert the vise assemblies through the holes
in the table edge and thread the leadscrew
into the leadscrew plate.
11. attach the leg supports to the leg assemblies
with the 5⁄16"-18 x 1" flange bolts, as shown in
figure 7, then secure the leg assemblies to
the workbench top with the 5⁄16"-18 x 1" flange
bolts.
9. With assistance, turn the workbench top
upside down on a flat, protected surface.
12. With assistance, flip the workbench right side
up, then adjust the foot pads to make the top
surface level.
10. slide the lower legs into the upper legs,
5
then secure them together with the ⁄16"-18 x
3
⁄4" hex bolts and flat washers, as shown in
figure 7.
13. attach the bottom shelf to the legs with
5
1
the ⁄16"-18 x ⁄2" flange bolts, as shown in
Note: Make sure that the completed leg
assemblies are all the same length, which will
dictate the height of the finished workbench
(from 32"–39").
figure 8.
Bench stop Bar
Bench dog
5⁄16"-18 x 3⁄4
hex Bolts & Flat
Washers
"
5⁄16"-18 x 1"
Flange Bolts
Bottom shelf
5⁄16" x 1⁄2
"
Flange Bolt
leg
support
figure 8. Bottom shelf installed.
5⁄16"18 x 1" Flange Bolts
14. insert the bench stop bars and the bench
dogs into the workbench top to finish the
assembly.
figure 7. installing the legs.
-3-
t10157 oak Workbench
parts
parts Breakdown and List
31
30
27
13
12
2
9
1
11
10
14
17
18
19
4
5
15
24
8
7
16
28
6
27
25
20
23
29
26
21
25
22
REF PART #
DESCRIPTION
QTY
REF PART #
DESCRIPTION
QTY
1
2
4
5
6
7
8
9
PT10157001 VISE LEADSCREW ASSEMBLY
PT10157002 TUBE
2
4
17 PT10157017 DRAWER PANEL RIGHT
18 PT10157018 DRAWER PANEL BACK
19 PT10157019 DRAWER PANEL BOTTOM
20 PT10157020 UPPER LEG
2
2
PT10157004 SCREW ANCHOR M8 X 30
PT10157005 WOOD SCREW M4 X 30
PT10157006 GLUE TUBE
16
16
1
2
4
21 PT10157021 LOWER LEG
4
PT10157007 BALL BEARING DRAWER SLIDE
PT10157008 WOOD SCREW M4 X 13
PT10157009 WORKBENCH TOP
4
22 PT10157022 FOOT PAD 1/2"-13 X 4"
23 PT10157023 BOTTOM SHELF
4
12
1
1
24 PT10157024 WOOD SCREW 5/16" X 1"
16
12
8
10 PT10157010 VISE FACE
2
25 PFB14
26 PB07
FLANGE BOLT 5/16"-18 X 1/2"
HEX BOLT 5/16"-18 X 3/4"
WOOD SCREW 1/4" X 1-1/2"
11 PT10157011 BENCH STOP BAR
12 PT10157012 VISE HANDLE
1
2
27 PWS003
20
2
13 PT10157013 VISE HANDLE CAP
14 PT10157014 BENCH DOG
2
28 PT10157028 LEADSCREW PLATE
29 PT10157029 LEG SUPPORT
4
2
15 PT10157015 DRAWER PANEL FRONT
16 PT10157016 DRAWER PANEL LEFT
2
30 PW07
31 PN02
FLAT WASHER 5/16"
HEX NUT 5/16"
4
2
4
-4-
t10157 oak Workbench
|