MODEL T10113
UNIVERSAL OVERARM
BLADE GUARD
INSTRUCTIONS
Introduction
the Model t10113 universal overarm Blade
guard is designed to fit most table saws with a
stable adjustable base and a 3" dust collection
boom that can rotate 90° and extend from 39" to
68" over the saw blade.
To reduce the risk of serious injury when
using this blade guard:
1. RIVING KNIfE. Before using this blade
guard, your table saw Must have the riv-
ing knife properly installed.
dust
4" dust hose here
Collection
Boom
2. BLADE GUARD hEIGhT. always properly
adjust the blade guard height so that the
guard wheels rest on the table and the
guard will not interfere with the workpiece
as it passes underneath.
3. TABLE SAW OWNER'S MANUAL. read
and understand the table saw owner's
manual and always follow all safety pre-
cautions and instructions for your table saw
during operation.
Blade
guard
table saw
Connection
Bracket
4. DUST COLLECTION SySTEM. always
use a dust collection system with this blade
guard that is adequate for your operation.
5. ADJUSTMENTS, MAINTENANCE, OR
SERVICE. always disconnect the table
saw from power before you perform any
adjustments, maintenance, or service to
this blade guard or your table saw.
figure 1. Model t10113 identification.
Inventory
after removing the contents of the shipping
package, lay them out and refer to the parts
Breakdown and listing on page 3 to inventory the
components.
6. TABLE SAW ATTAChMENT. always make
sure the blade guard assembly is firmly
attached to the table saw so that the blade
guard will not move away from its correct
and safe position during operation.
If you need help with your new Universal Overarm
Blade Guard, call our Tech Support at: (570) 546-
9663.
Copyright © NoVEMBEr, 2008 By grizzly iNdustrial, iNC.
WARNING: NO pORTION Of ThIS MANUAL MAy BE REpRODUCED IN ANy ShApE
OR fORM WIThOUT ThE WRITTEN AppROVAL Of GRIzzLy INDUSTRIAL, INC.
#ts11340 priNtEd iN taiWaN
parts breakdown
parts Breakdown
27
48
10
18
30
4
5
40
35
31
14
31
18
34
31
29
23
36
44
6
33
37
40
47
32
12
1
43
46
22
19
42
45
19
19
26
13
29
11
41
20
8
16
15
18
44
2
38
24
28
17
38
21
26
17
19
7
38
38
9
3
25
38
26
9
39
REF PART #
DESCRIPTION
REF PART #
25 PSB106
DESCRIPTION
CAP SCREW 5/16-18 X 4
QTY
1
QTY
2
1
2
3
4
5
6
7
8
9
PT10113001 OUTER BOOM
PT10113002 VERTICAL SUPPORT
PT10113003 EXTENSION TUBE
PT10113004 PIVOT ARM
26 PT10113026 THREADED FOOT 1/2-13 X 3
1
3
27 PSB05
28 PFB01
29 PLW02
30 PCB23
CAP SCREW 1/4-20 X 3/4
FLANGE BOLT 5/16-18 X 1/2
LOCK WASHER 1/4
1
1
1
1
PT10113005 BOOM END CAP
PT10113006 INNER BOOM
PT10113007 SLIDING BRACE
1
2
CARRIAGE BOLT 1/4-20 X 2-1/4
1
4
31 PT10113031 PLASTIC FLAT WASHER 1/4
32 PSBS34M BUTTON HD CAP SCR M5-.8 X 25
33 PT10113033 LOCK LEVER 1/4-20
34 PLN02 LOCK NUT 1/4-20
35 PT10113035 LOCK LEVER 1/4-20 X 1/2
2
8
PT10113008 CONNECTING BRACKET
PT10113009 SIDE SUPPORT LEG
1
1
2
1
10 PT10113010 PIVOT SHAFT
11 PT10113011 GUARD HANDLE
12 PT10113012 BLADE GUARD
13 PT10113013 FRONT THREADED AXLE
14 PT10113014 BOOM KEY
4
3
1
1
36 PSBS06M
37 PSBS35M
38 PN06
BUTTON HD CAP SCR M5-.8 X 12
BUTTON HD CAP SCR M5-.8 X 10
HEX NUT 1/2-13
1
1
1
1
1
5
15 PB99
HEX BOLT 1/2-13 X 2-1/4
39 PT10113039 THREADED FOOT 1/2-13 X 4
40 PT10113040 HOSE CLAMP 3"
1
1
16 PT10113016 GUARD WHEEL
4
2
17 PW07
18 PN05
19 PN02
FLAT WASHER 5/16
HEX NUT 1/4-20
41 PT10113041 LOCK LEVER 5/16-18 X 5/8
42 PT10113042 CONNECTING PLATE
4
1
4
1
HEX NUT 5/16-18
43 PB32
44 PW06
45 PFB16
46 PFN02
HEX BOLT 5/16-18 X 5/8
FLAT WASHER 1/4
6
1
20 PT10113020 AXLE CLIP
4
3
21 PB98
22 PB03
23 PS07
24 PCB05
HEX BOLT 1/4-20 X 2-1/2
FLANGE BOLT 5/16-18 X 1
FLANGE NUT 5/16-18
1
2
HEX BOLT 5/16-18 X 1
1
2
PHLP HD SCR 1/4-20 X 3/8
47 PT10113047 REAR THREADED AXLE
48 PT10113048 DUST HOSE 3" X 24"
1
1
CARRIAGE BOLT 5/16-18 X 3/4
2
1
-3-
t10113 universal overarm Blade guard
Customize your Table Saw Even More!
G1317—37" Wide Outfeed Roller System
h8875—26" Wide Outfeed Roller System
these unique roller systems fold down easily
without tools and snap up in place quickly when
needed. Both units have a double level system
which lets you set the rollers either in line with the
table or slightly below it.
G4227—Sliding Table for 10" Table Saws
G8010—Sliding Table for 14" Table Saws
perfect for cutting large sheet stock! the table
glides effortlessly on five ball bearing rollers,
attaches directly to your saw or shaper table
and can be adjusted for precision results. Model
g4227 fits our g1023 series (except g1023sl &
g1023slX), g1035, g1026 and most other cabi-
net saws and full size shapers. Model g8010 fits
our g7209/g7210 14" table saws.
g4227
Model G1317 Shown
figure 2. outfeed roller system.
G7314—heavy-Duty Mobile Base
G8684—Extension Kit for Mobile Base
this heavy duty mobile base is rated for up to a
600 lb. capacity.
figure 4. g4227 sliding table attachment.
G4173—1⁄8 hp power feeder
G4173—1⁄4 hp power feeder
G4179—1⁄2 hp power feeder
installing a power feeder on your table saw will
make repetitive cuts much easier and safer.
Can be installed on nearly any table saw. Easy
to adjust wherever needed, including out of the
way when not needed! a must for any production
shop.
g8684
g7314
figure 3. g7314 mobile base and extension kit.
h4332—T4 Silencer for Saw Blades
Woodworkers across the country swear by these
blade silencers.
power Twist® V-Belts
h9815—A 1⁄2" x 4'
h9817—B 5⁄8" x 6'
Works with multi-sheave pulleys. reduces noise!
figure 5. g4179 power Feeder.
|