mOdel h0580
pneumAtIc greASe
gun
InStructIOn Sheet
Head
Assembly
eye InJury hAzArd!
Always wear safety glasses
during use to prevent
serious personal injury.
InJury hAzArd!
When servicing, always dis-
connect tool from air to pre-
vent unexpected operation.
Cartridge Body
150 pSI
Hydraulic Coupler Extension
mAX AIr preSSure!
exceeding this pSI may
result in injury/tool damage.
Figure 1. Model H0580.
Specifications
Quick
Connector
Quick
Connector
Lubricator
Regulator
Air Inlet ....................................................1⁄4" NPT
Average Air Consumption ........................ 4 CFM
Operating Pressure .................................. 90 PSI
Capacity................... 14 oz., (400cc bulk grease)
Weight ........................................3.2 lbs. (Empty)
Your
Tool
Air
Compressor
Quick
Coupler
Quick
Coupler
Air Hose
Filter
Inventory (Figure 1)
A. Grease Gun ............................................... 1
B. Hydraulic Coupler with Extension .............. 1
Qty
Figure 2. Installing a filter/lubricator/regulator to
improve the lifespan of your tool.
Operation
To improve tool lifespan, use a filter/lubricator/
regulator setup, as shown in Figure 2.
Otherwise, lubricate multiple times daily with 2–3
drops of pneumatic tool oil. Place the oil directly
into the air fitting, as shown in Figure 3.
Figure 3. Lubricating directly into air fitting.
If you need help with your new pneumatic tool,
call our Tech Support at: (570) 546-9663.
COPyrIGHT © MAy, 2008 By GrIzzLy INduSTrIAL, INC.
WArnIng: nO pOrtIOn OF thIS mAnuAl mAy Be reprOduced In Any ShApe
Or FOrm WIthOut the WrItten ApprOvAl OF grIzzly InduStrIAl, Inc.
#jM10671 PrINTEd IN TAIWAN
Filling from a Bulk grease container
1. dISCONNECT THE TOOL FrOM THE AIr
SuPPLy!
Filling With a Bulk grease pump
1. dISCONNECT THE TOOL FrOM THE AIr
SuPPLy!
2. Pull the follower rod back until it is fully
extended, the locking tab will automatically
hold it in place (Figure 4).
2. Pull the follower rod back until it is fully
extended, the locking tab will automatically
hold it in place.
3. remove the head assembly from the car-
3. Insert the grease gun grease inlet (part # 11)
into the proper fitting on the pump operated
bulk grease container.
tridge tube.
4. remove any grease from the cartridge tube
by pushing the locking tab and carefully
releasing the follower rod, allowing it to slowly
move into the cartridge tube.
4. Operate the bulk grease pump to fill the
grease gun container.
5. remove the grease gun from the pump and
5. Without introducing bubbles, pack grease
into the head cavity and plunger assembly
until they are full (Figure 5).
release the locking tab.
6. Push the follower rod in as far as possible.
Bleeding Air pockets
Head Cavity
If at any time you experience problems with the
grease gun dispensing grease, especially after
refilling, air is likely trapped in the head assem-
bly.
Plunger Assembly
to bleed air pockets from the grease gun:
1. dISCONNECT THE TOOL FrOM THE AIr
SuPPLy!
Bleeder Valve
2. Pull back on the follower rod until it is fully
extended (Figure 4).
Figure 5. Grease locations and bleeder valve.
3. release the follower rod by pushing on the
6. Insert the open end of the cartridge tube into
the barrel or drum of the bulk grease to be
added.
locking tab.
4. Push the follower rod all the way forward
while holding down the bleeder valve shown
in Figure 5, until the air is expelled from the
gun.
7. Slowly pull the follower handle back while
pushing the cartridge tube deeper into the
grease. This method will help prevent draw-
ing in air bubbles.
5. reconnect the grease gun to the air supply,
and pull the trigger several times to release
any air in the head assembly and verify the
grease gun works correctly.
8. When the follower rod is fully extended, allow
the locking tab to hold it in place (Figure 4).
9. Securely fasten the head assembly to the
cartridge tube and release the follower rod by
pushing on the locking tab.
note: If the grease gun does not dispense
grease correctly, repeat this procedure as
many times as necessary.
10. Push the follower rod in as far as possible.
-3-
H0580 Pneumatic Grease Gun
h0580 parts Breakdown and list
*
)
.
-
&-
,
&,
("&
("'
&%
&&
(
&.
&
&'
&(
&)
+
'
&*
&+
'%
'&
&-"&
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PH0580001
PH0580002
PH0580003
GREASE GUN BODY
1/4" NPT AIR INLET
SWITCH
11
12
13
14
15
16
17
18
PH0580011
PH0580012
PH0580013
PH0580014
PH0580015
PH0580016
PH0580017
PH0580018
GREASE INLET
GASKET
2
3
PLUNGER NUT
PLUNGER WASHER
PLUNGER
3-1
3-2
4
PH0580003-1 TRIGGER AND PIN
PRP37M
ROLL PIN 3 X 14
PH0580004
PH0580005
PH0580006
PH0580007
PH0580008
PH0580009
PH0580010
SPECIAL BODY SCREW
AIR PLUNGER
BACKLASH GASKET
LONG SPRING KIT
CARTRIDGE TUBE
5
6
SHORT SPRING
HEAD
7
18-1 PH0580018-1 BOTTOM CAP
8
ADAPTER
19
20
21
PH0580019
PH0580020
PH0580021
FOLLOWER ROD
ROD HANDLE
LOCKING TAB
9
HYDRAULIC COUPLER EXTENSION
BLEEDER VALVE
10
|