HP Hewlett Packard Digital Photo Frame DF808 User Manual

HP df808 Series  
Digital Picture Frame  
User Manual  
 
FCC Compliance Statement  
Note: This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses,  
and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will  
not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct  
the interference by one of the following measures:  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that  
to which the receiver is connected.  
- Consult the dealer or an experienced radio/TV technician for help.  
FCC Caution: To assure continued compliance, only use shielded interface  
cables when connecting to computer or peripheral devices. Any changes  
or modifications not expressly approved by the party responsible for  
compliance could void the user’s authority to operate this equipment.  
This device complies with Part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
1
 
Table of Contents  
What’s in the Box..........................................................2  
Getting Started..............................................................3  
Installing the Foot Stand..............................................5  
Powering on the Frame.................................................6  
Using the Digital Photo Frame......................................7  
Settings Menu..............................................................15  
Cleaning and Care Tips................................................17  
Getting Help.................................................................18  
2
 
What’s in the Box  
Qty  
Item  
Image  
1
Digital Picture Frame  
Remote Control  
Replacement Battery = CR2025  
1
1
1
Universal Power Adapter (5V, 2A)  
USB Cable  
User Manual with  
Declaration of Conformity  
1
1
1
Quick Start Guide  
Warranty Document  
3
 
Getting Started  
Identifying the parts  
Front view  
LCD (Liquid Crystal Display) panel  
Rear view  
Control buttons  
Hanging slot  
Lock slot  
4
 
Left view  
Mini USB port for file transfer  
Power switch transfer  
Power socket  
Right view  
5-in-1 memory card slot  
(SD/SDHC, MMC, MS, MS-Pro, xD)  
CF memory card slot  
Foot stand  
5
 
Installing the Foot Stand  
1. On the back of the frame, align the foot stand with the lock slot.  
2. Install the foot stand onto the frame as illustrated until it clicks into  
place.  
6
 
Powering on the Frame  
1. Plug the AC power adapter into the power outlet, then plug the other  
end into the power socket of the frame.  
2. Insert a memory card (to be purchased separately) to the appropriate  
card slot.  
Note:  
You can also view the demo images preloaded in the internal  
memory of this frame without inserting a memory card.  
Supported memory card type: Secure Digital™, xD-Picture Card™,  
MultiMedia Card™, Memory Stick™, and Memory Stick PRO™.  
Both 5-in-1 and CF memory card slots support hot-swap function.  
When one memory card is inserted and then a second one is  
inserted, the frame only will display files from the second one.  
When two memory cards are inserted simultaneously and the  
power is turned off and then back on, the frame only will display  
files from the SD card.  
• This frame may not read all image or video files downloaded from  
the Internet.  
3. Turn on the frame by sliding the power switch to the ON position.  
7
 
Using the Digital Photo Frame  
Using the control buttons  
You can operate this frame by pressing the control buttons which are located  
on the back of the frame. The icons at the top of the screen correspond to the  
control buttons. If there are no icons at the top of the screen, then press any  
of the control buttons to display the icons.  
Note: Control buttons do not always perform the same function between  
modes.  
Using the remote control  
This frame comes with a remote control. Below is a table of all the buttons  
and a description of their functions.  
Note: This guide assumes you are using the remote control to control the  
frame.  
8
1
9
2
3
4
11  
12  
5
6
7
13  
No  
Description  
Backlight Saving  
Press this button to activate Backlight Saving function.  
1
Alarm  
2
3
In Calendar mode, you can press this button to set up the alarm.  
Setup  
Press this button to access the Setup menu.  
Mode selection  
4
5
Press this button to switch among different Photo, Calendar, Video, and  
Settings modes.  
Return  
Press this button to cancel current action and/or go back to the previous  
page.  
8
 
OK & Play/Pause  
6
7
Press this button to confirm a selection, start, or pause file playback.  
Copy  
Press this button to copy a selected file to the internal memory.  
Mute  
8
Press this button to activate the Mute mode. Press it again to restore the  
volume.  
Vol+ / Vol-  
9
Press these buttons to increase/decrease the volume.  
Rotate  
Each time you press this button, the selected photo rotates clockwise 90  
degrees.  
10  
11  
Zoom in/Zoom out  
Press these buttons to zoom in/zoom out the selected image file.  
Navigation buttons  
• In list or menus: Press to scroll up, down, left or right.  
12  
13  
/
: Press to scroll to the previous/next item.  
Delete  
Press this button to delete the selected file.  
9
 
Main Menu  
You can access the different modes from the main menu.  
Press the  
Press  
button to view the main menu as illustrated below.  
button to view the Main Menu as illustrated below.  
Note:  
Depending on the screen you are originating from, you will have to  
press the button either once or twice to display the main menu.  
Press the  
once to cycle to the next mode icon.  
When you get to the desired mode icon, allow two seconds for the  
mode to be selected.  
5 modes available: Photo, Calendar, Music, Video, and Settings Menu  
Photo mode  
The Photo mode allows you to view images in three kinds of viewing  
modes: slideshow view, single view, and thumbnail view.  
After the frame is turned on, a slideshow starts automatically.  
Note: In a slideshow, background music will play sequentially if the  
feature has been enabled. Please refer to the section on the  
Settings Menu on page 14  
10  
 
Slideshow mode will begin automatically a few seconds after the  
frame is powered on or when an external memory card is inserted.  
To switch to thumbnail view, press the button  
. Use buttons  
and  
to move among images.  
To switch to photo slideshow mode, press the button  
.
To view images individually, press  
again to pause slideshow on  
a particular photo.  
Note: • This frame only supports the JPEG file format.  
Calendar mode  
The Calendar mode displays a monthly calendar.  
After you turn on the frame, press the button  
to switch to the  
Calendar mode.  
To switch to the next month, press the button  
To switch to the previous month, press the button  
.
.
Setting the date and time  
1. Go to the Calendar mode  
2. Press the button  
3. Use the buttons  
to go to Calendar setup menu.  
to move to different fields, and use the  
/
buttons  
/
to adjust date and time.  
.
4. Press the button  
Setting the alarm  
1. Go to the Calendar mode.  
11  
 
2. Press the button  
3. Use the buttons  
.
/
to move to different fields, and use the  
buttons  
/
to adjust alarm time, tone, and mode.  
.
4. Press the button  
Music mode  
The Music mode allows you to play audio files that are stored in the  
internal memory or on the inserted memory card.  
Note: • This frame only supports the MP3 audio file format.  
Playing the music  
1. After you turn on the frame, press the button  
Music mode.  
to switch to the  
2. Press the button  
to show the Music List.  
3. Use the buttons  
4. Press the button  
/
to select a music file.  
to start the playback.  
To increase volume, press the button  
To decrease volume, press the button  
.
.
Deleting a music file  
1. After you turn on the frame, press the button  
Music mode.  
to switch to the  
2. Press the button  
to show the Music List.  
3. From the Music List screen that appears, use the buttons  
/
12  
 
to select the music file to be deleted.  
4. Press the button  
.
5. A confirmation message appears.  
To delete the selected music file, press the button  
.
To cancel, press the button  
.
Note: • This frame only deletes files from internal memory.  
Copying a music file  
1. After you turn on the frame, press the button  
mode.  
to switch to the Music  
2. Press the button  
to show the Music List.  
3. From the Music List screen that appears, use the buttons  
/
to  
select the music file to be copied.  
4. Press the button  
.
5. A confirmation message appears.  
To copy the selected music file, press the button  
.
To cancel, press the button  
.
Note: • This frame only copies files from external memory to internal memory.  
Video mode  
Viewing a video file  
1. After you turn on the frame, press the button  
mode.  
to switch to the Video  
2. The Video List screen appears.  
13  
 
3. Use the buttons  
4. Press the button  
/
to select a video file.  
to start the playback.  
To increase volume, press the button  
To decrease volume, press the button  
.
.
Note:  
• This frame only supports Motion JPEG video file format (640X480  
at 30 fps).  
Deleting a video file  
1. After you turn on the frame, press the button  
Music mode.  
to switch to the  
2. The Video List screen appears.  
3. From the Video List screen that appears, use the buttons  
/
to select the video file to be deleted.  
4. Press the button  
.
5. A confirmation message appears.  
To delete the selected video file, press the button  
.
To cancel, press the button  
.
Note: • This frame only deletes files from internal memory.  
Copying a video file  
1. After you turn on the frame, press the button  
Video mode.  
to switch to the  
2. The Video List screen appears.  
3. From the Video List screen that appears, use the buttons  
/
to select the video file to be copied.  
14  
 
4. Press the button  
.
5. A confirmation message appears.  
To copy the selected video file, press the button  
.
To cancel, press the button  
.
Note: • This frame only copies files from external memory to internal  
memory.  
15  
 
Settings Menu  
After you turn on the frame, press the mode selection button to switch  
to the Settings mode.  
Settings  
menu  
Sub-menus  
Formats the internal memory.  
Optimizes the image to fit the whole  
screen.  
Note: Some cropping of the images  
may occur in this option.  
Full Screen  
Photo Display  
Displays images in their original aspect  
Real Size  
On  
ratio.  
Allows you to display or hide the  
information about image files in the  
thumbnail mode.  
Photo  
Information  
Off  
On  
Off  
Allows you to display or hide the clock in  
the slideshow mode.  
Display Clock  
On  
Off  
Background  
Music  
Turns the background music on or off.  
5 Secs  
30 Secs  
1 Min.  
15 Mins.  
30 Mins.  
1 Hr.  
Frequency  
Selects speed of your slideshow.  
4 Hrs.  
12 Hrs.  
1 Day  
1 Week  
None  
Slideshow  
Setup...  
Fade  
Shutter  
Cross  
Mask  
Effect  
Order  
Selects style of image transition.  
Brick  
Allows images to be displayed in a  
sequential order.  
Allows images to be displayed in a  
random order.  
Sequential  
Random  
16  
 
0
1
2
3
4
5
Allows you to adjust the brightness of  
the screen.  
Brightness  
Language  
Auto Copy  
English  
French  
Spanish  
Changes the OSD menu language.  
System  
Setup...  
Allows you to select whether image files  
will be automatically copied from an  
inserted memory card to the internal  
memory. An auto copy message will  
appear once a memory card is inserted.  
On  
Off  
Press the button  
to confirm.  
System Reset...  
Format...  
Reset all settings back to default.  
Formats the internal memory.  
Note: If you use this option to format  
the internal memory, all image/ video/  
audio files will be deleted permanently.  
17  
 
Cleaning and Care Tips  
Please power off the HP Digital Picture Frame before cleaning.  
DO NOT push on the screen too firmly.  
DO NOT spray or pour liquid cleaning agents directly on the screen  
or frame.  
DO NOT use ammonia, alcohol, or abrasive detergent cleaning  
agents.  
Cleaning the Screen:  
1. Wipe screen with a clean, soft, lint-free cloth to remove dust and  
loose particles.  
2. If further cleaning is required, apply an appropriate cleaning agent  
(approved for LCD displays) to a clean, soft, lint-free cloth and wipe  
the screen.  
Cleaning the Frame and Backing:  
1. Use a clean, soft, lint-free cloth to remove dust and loose particles.  
2. If desired, apply an appropriate cleaning agent to a clean, soft,  
lint-free cloth and wipe the appropriate surfaces.  
18  
 
Getting Help  
Should your HP Branded Product require service within the Warranty  
period, please contact the original point of purchase or an authorized  
HP reseller in your country. If service is not available at those locations,  
please contact an HP Branded Product warranty agent from the support  
contact list provided on this document. Supported languages are:  
English, French, German, Italian, Portuguese and Spanish. A warranty  
agent will work with you to troubleshoot your issue and if necessary,  
issue a Return Material Authorization (RMA) number in order to replace  
your HP Branded Product. For warranty claims, you will be required to  
provide a copy of your original dated sales receipt as proof of purchase  
and the issued RMA number. End User customer shall be responsible  
for shipping charges when shipping the product to the service center.  
The service agent will provide you with an address and you will also be  
responsible for any shipping charges to the warranty service center. Once  
your product is received by the service center, a replacement frame will  
be shipped back to you within 5 business days.  
Email Support:  
Language  
English  
Email Address  
Français  
Italiano  
Espanol  
Portuguese  
Dutch  
Deutsch  
Svensk  
Chinese  
19  
 
Contact/Phone Support:  
Country  
Language  
Number  
België  
Dutch and German  
German  
+ 32 2700 1724  
+ 49 6950073896  
+ 34 914533458  
+ 33 171230454  
+ 353 1850882016  
+ 39 269682189  
+ 31 202015093  
+ 41 18009686  
+ 44 2073652400  
Deutchland  
España  
Spanish  
France  
French  
Ireland  
English  
Italia  
Italian  
Nederland  
Switzerland  
United Kingdom  
North America  
United States  
Canada  
Dutch  
German/French/Italian  
English  
English  
+ 1-866-694-7633  
+ 1-866-694-7633  
English & French  
20  
 
P/N: 7525C00066A  
 

Grizzly Saw G4570 User Manual
Haier Dishwasher HDB24VA User Manual
Harbor Freight Tools Automobile Accessories 95288 User Manual
Harbor Freight Tools Grinder 42203 User Manual
Hotpoint Refrigerator RLA175P User Manual
Husqvarna Chainsaw I0300046 User Manual
Husqvarna Lawn Mower 07002 User Manual
Hypercom Network Router IEN2500 User Manual
Icom Two Way Radio IC F610 User Manual
IKEA Indoor Furnishings AA 177772 2 User Manual