HP-UX 11i Version 2 Installation and
Update Guide
HP Integrity Servers and HP Workstations
Manufacturing Part Number : 5187-2725
October 2003, Edition 1
United States
© Copyright 1983-2003 Hewlett-Packard Development Company, L.P.
Trademark Notices
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
HP-UX Release 10.20 and later and HP-UX Release 11.00 and later (in
both 32 and 64-bit configurations) on all HP 9000 computers are Open
Group UNIX 95 branded products.
Intel and Itanium are registered trademarks of Intel Corporation in
the US and other countries and are used under license.
Java is a US trademark of Sun Microsystems, Inc.
MS-DOS , Microsoft , and Windows are registered trademarks of
Microsoft Corporation in the United States of America and in other
countries.
UNIX is a registered trademark of The Open Group.
3
Publication History
The manual publication date and part number indicate its current
edition. The publication date will change when a new edition is released.
The manual part number will change when extensive changes are made.
To ensure that you receive the latest edition, you should subscribe to the
appropriate product support service. See your HP sales representative
for details.
Related Document: HP-UX 11i Version 1.6 Installation and
Configuration Guide, July 2002, 5187-1087, (HP-UX 11iV1.6),
CD (Instant Information), and web (http://www.docs.hp.com)
New editions of this manual will incorporate all material updated since
the previous edition. For the latest version, see the HP-UX 11i v2
documentation on the web:
http://docs.hp.com/hpux/os/11iv2
Please direct comments regarding this guide to:
Hewlett-Packard Company
HP-UX Learning Products
3404 East Harmony Road
Fort Collins, Colorado 80528-9599
Or, use this web form to send us feedback:
http://docs.hp.com/assistance/feedback.html
4
About This Guide
This guide describes cold-installing and updating HP-UX 11i v2 on HP
Integrity Servers and HP Workstations, and assumes that you are the
system administrator and familiar with installing and maintaining
software on the system.
This guide applies to the October 2003 version of HP-UX 11i v2. If you
need information for a previous version of HP-UX 11i, go to the web:
http://docs.hp.com
If you need to set up your system in different languages, please refer to
Configuring HP-UX for Different Languages, available on the Instant
Information DVD and on the HP documentation web site:
http://docs.hp.com
A localized version of the manual is available with localized media kits.
Latest versions are available at the HP documentation web site.
5
Typographic Conventions
We use the following typographical conventions.
audit (5)
HP-UX manpage. audit is the name and 5 is the section
in the HP-UX Reference. On the web and on the Instant
Information DVD, it may be a hot link to the manpage
itself. From the HP-UX command line, you can enter
“man audit” or “man 5 audit” to view the manpage.
See man (1).
Book Title
Title of a book. On the web and on the Instant
Information DVD, it may be a hot link to the book
itself.
Command
Command name or qualified command phrase.
Text displayed by the computer.
Text that is emphasized.
ComputerOut
Emphasis
Emphasis
KeyCap
Text that is strongly emphasized.
Name of a keyboard key. Note that Return and Enter
both refer to the same key.
Term
Defined use of an important word or phrase.
Commands and other text that you type.
UserInput
Variable
Name of a variable that you may replace in a command
or function or information in a display that represents
several possible values.
[ ]
{ }
Contents are optional in formats and command
descriptions. If the contents are a list separated by |,
you must choose one of the items.
Contents are required in formats and command
descriptions. If the contents are a list separated by |,
you must choose one of the items.
...
|
Preceding element may be repeated an arbitrary
number of times.
Separates items in a list of choices.
6
Welcome to HP-UX 11i Version 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
HP-UX 11i Release Names and Release Identifiers . . . . . . . . . . . . . . . . . . . . . . . . . . 19
How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
What is HP-UX 11i v2? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Features and Applications Available in HP-UX 11i v2. . . . . . . . . . . . . . . . . . . . . . . . 21
Features Unavailable in HP-UX 11i v2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Media Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
HP-UX 11i v2 Operating Environments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Mission Critical OE Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Other Sources of Information about This Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
HP Documentation Web Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
HP-UX 11i v2 Instant Information Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
HP-UX Welcome Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Manual Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
README Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
White Papers on HP-UX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
The Next Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
If You Have an Existing HP-UX 11i v2 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Migrating from Previous HP-UX Releases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Supported Cold-Install Paths to HP-UX 11i v2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Supported Update Paths to HP-UX 11i v2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Deciding Which Method to Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
When to Cold-Install. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
When to Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Installing Network Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Cold-Install Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Update Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Install-time Security Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Security Choice Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Secured Services and Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
The Next Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
3. Installing and Updating System Requirements
7
Contents
Factory Ignited Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Disk Space Allocation for File Partitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Update Disk Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
How to Plan Your Disk Space Needs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Supported Servers and Workstations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Unsupported Servers and Workstations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Keeping Up with Firmware Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Identifying Model, OS/OE, and Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
The Next Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Update Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Recording Software Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Rebuilding the Kernel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Cleaning Out Your Log Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Updating Your Ignite-UX Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Selecting Your HP-UX Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Interface Differences between Itanium-based Systems . . . . . . . . . . . . . . . . . . . . . . . 68
Additional Notes on Console Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
About Online Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
About Offline Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Backing Up Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Saving Configuration Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Locating Source Media and Codewords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Locating Codewords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
The Next Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
5. Cold-Installing HP-UX 11i v2
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Reviewing the Cold-Install Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Cold-installing HP-UX 11i v2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Continuing the Install with Ignite-UX Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Continuing with Guided Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
8
Retrieving Information after Cold-installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
The Next Step. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Reviewing the Update Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Updating Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Monitoring the Update Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Running Other Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
In Case of Trouble. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
All Software Does Not Get Updated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Updating to HP-UX 11i v2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Optional Step: Creating a Network Depot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Step 1: Installing the update-ux Command (Required Task). . . . . . . . . . . . . . . . . . 100
Step 2: Using update-ux to Update to HP-UX 11i v2 . . . . . . . . . . . . . . . . . . . . . . . . 101
Configuring OE Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Creating an HP Service Partition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
The Next Step. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
7. Verifying System Install or Update
Verifying the HP-UX Install or Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Verifying HP-UX Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Changing the State of HP-UX Installed Patches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
The Next Step. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Keeping Up to Date with the Latest Critical Patches . . . . . . . . . . . . . . . . . . . . . . . . . 126
HP-UX Patching Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Installing OS Patches Required by Individual Applications . . . . . . . . . . . . . . . . . . . . 128
Determining the List of Previous HP-UX patches . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Obtaining Newer HP-UX patches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Getting HP-UX Patch Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Removing HP-UX Patches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Adding HP-UX Patches to a Software Depot or System. . . . . . . . . . . . . . . . . . . . . . 129
Tips for Installing or Updating HP Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Installing Optional Software Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Using Ignite-UX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Backing Up the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
9
Contents
The Next Step. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Configuring Your HP-UX 11i v2 System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Maintaining Your HP-UX 11i v2 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
A. Data Collection Tables
Network Data Collection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Miscellaneous Data Collection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
B. Known Problems and Troubleshooting
Known Install/Update Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
HP CIFS Server Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
v2 Ignite-UX Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
HIDS Becomes Unbundled during Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
“Incorrect protocol version (20) in volboot file” Error . . . . . . . . . . . . . . . . . . . . . . . . 148
mod_load_helper Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Uninstalling HP-UX 11i v2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Restrictions with Netscape Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Netscape 4.x Unbundles during Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Netscape 7.0 Aborts with ja_JP.utf8 Locale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Character-code Handling with Perl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
C. Controlling Memory Utilization of VxFS 3.5 on HP-UX 11i v2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Controlling the inode Cache . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Controlling the Buffer Cache. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
D. Software Distribution Media
HP-UX 11i v2 Operating Environments at a Glance. . . . . . . . . . . . . . . . . . . . . . . . . . 162
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
HP-UX 11i v2 Foundation OE (FOE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
10
HP-UX 11i v2 Enterprise OE (EOE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
HP-UX 11i v2 Mission Critical OE (MCOE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
HP-UX 11i v2 Minimal Technical OE (MTOE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
HP-UX 11i v2 Core Software Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
HP-UX 11i v2 Always-Installed Software Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
HP-UX 11i v2 Default-Installed Software Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
HP-UX 11i v2 Selectable Software Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
HP-UX 11i v2 Selectable Network Drivers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
E. Web Resources
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
11
Contents
12
Table 1-2. Supported Operating Environments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Table 2-2. Predefined Security Configuration Bundles . . . . . . . . . . . . . . . . . . . . . . . .43
Table D-1. Supported Operating Environments. . . . . . . . . . . . . . . . . . . . . . . . . . . . .163
Table D-2. HP-UX 11i v2 Core Software Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . .170
Table D-3. HP-UX 11i v2 Always-Installed Software Bundles (by OE) . . . . . . . . . .171
Table D-4. HP-UX 11i v2 Always-Installed Network Drivers . . . . . . . . . . . . . . . . . .174
Table D-5. HP-UX 11i v2 Default-Installed Software Bundles (all OEs) . . . . . . . . .175
Table D-6. HP-UX 11i v2 Selectable Software Bundles (all OEs) . . . . . . . . . . . . . . .177
Table D-7. HP-UX 11i v1 Selectable Network Drivers. . . . . . . . . . . . . . . . . . . . . . . .178
13
Tables
14
Figure 2-1. Install-time Security Software Dependencies . . . . . . . . . . . . . . . . . . . . . .44
Figure 5-1. Cold-installing HP-UX 11i v2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Figure 6-1. Updating to HP-UX 11i v2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Figure 6-2. idisk Output Showing No HP Service Partition Installed . . . . . . . . . . .110
Figure 6-3. idisk Output Showing HP Service Partition Installed . . . . . . . . . . . . . .111
Figure 9-1. Reactive Software Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
15
Figures
16
1
Welcome to HP-UX 11i Version 2
contents, and other resources of HP-UX 11i Version 2 (B.11.23).
•
•
•
•
•
•
•
•
“Introduction” on page 19
“How to Use This Guide” on page 20
“Media Kit Contents” on page 24
“HP-UX 11i v2 Operating Environments” on page 25
“Other Sources of Information about This Release” on page 27
“The Next Steps” on page 30
To complete the review in this chapter, we estimate you require 1 hour.
Please note that your time may vary.
Chapter 1
17
Welcome to HP-UX 11i Version 2
Welcome to HP-UX 11i Version 2
Welcome to HP-UX 11i Version 2
HP-UX 11i Version 2 is the newest release of HP-UX 11i for the Intel
Itanium architecture. This enterprise release offers a full range of
HP-UX Operating Environments, including systems management and
high-availability software products. Itanium-based systems offer
significantly better price/performance and performance scalability than
systems based on current architectures, and HP-UX 11i v2 provides the
best way to preserve your investment through the transition from
PA-RISC systems to Itanium-based systems.
Hewlett-Packard's enterprise computing business has carefully planned
the transition to Itanium-based systems, placing a premium on customer
and partner investment protection. HP-UX 11i v2 maintains
compatibility with HP-UX 11iv1 on PA-RISC through the following:
•
•
Common “look and feel”
Application Build Environment compatibility (source code
compatibility)
•
•
Data compatibility
Binary compatibility
HP-UX 11i v2 offers these industry firsts for Itanium-based systems:
•
Support for HP-UX 11i, Linux, and Windows running in separate
hardware-based partitions on the same computer
•
•
64-way performance scaling
iCOD (Instant Capacity on Demand) and Pay-Per-Use (PPU)
HP-UX 11i v2 brings to Itanium-based systems the full power of HP
11iv1, the #1-rated UNIX operating system (OS) in the world (DH Brown
2002 UNIX OS Review; see the web site:
http://www.hp.com/hpinfo/newsroom/press/2002/020530b.html
HP-UX 11i v2 on Itanium takes its place alongside HP-UX 11i v1 on
PA-RISC as an industry mainstay for mission critical enterprise
applications.
18
Chapter 1
Welcome to HP-UX 11i Version 2
Introduction
Introduction
HP-UX 11i Version 2 is the latest release for most Itanium-based HP-UX
systems. The Release ID for HP-UX 11i Version 2 is B.11.23, and we use
the term HP-UX 11i v2 throughout this guide. The HP-UX 11i v2
Operating Environments (OEs) are integrated and tested software
solutions containing the operating system and selected applications.
Precision Architecture Reduced Instruction Set Computing
(PA-RISC)-based systems should continue to run HP-UX 11iv1 (Release
ID B.11.11) or earlier releases. HP-UX 11i v2 does not run on
PA-RISC-based systems.
HP-UX 11i Release Names and Release Identifiers
With HP-UX 11i, HP delivers a highly available, secure, and manageable
operating system that meets the demands of end-to-end Internet-critical
computing. HP-UX 11i supports enterprise, mission critical, and
technical computing environments. HP-UX 11i is available on both
PA-RISC systems and Itanium-based systems.
Each HP-UX 11i release has an associated release name and release
identifier. The uname (1) command with the -roption returns the
release identifier. The following table shows the releases available for
HP-UX 11i.
Table 1-1
HP-UX 11i Releases
Supported
Processor
Release Identifier Release Name
Architecture
B.11.11
B.11.20
B.11.22
B.11.23
HP-UX 11i v1
HP-UX 11i v1.5
HP-UX 11i v1.6
HP-UX 11i v2
PA-RISC
Intel Itanium
Intel Itanium
Intel Itanium
Chapter 1
19
Welcome to HP-UX 11i Version 2
How to Use This Guide
How to Use This Guide
To help ensure a successful cold-install or update of HP-UX 11i v2, we
recommend that you review this guide before proceeding to cold-install
or update the operating system or an operating environment on your
system. This guide provides detailed information regarding both the
hardware and the software that together makeup your new system.
IMPORTANT
We provide any last-minute cold-install and update information in the
Read Before Installing or Updating to HP-UX 11i Version 2 DVD booklet
Appendix C, “Controlling Memory Utilization of VxFS 3.5 on HP-UX 11i
v2,” on page 155
Appendix D, “Software Distribution Media,” on page 161
Appendix E, “Web Resources,” on page 179
20
Chapter 1
Welcome to HP-UX 11i Version 2
What is HP-UX 11i v2?
What is HP-UX 11i v2?
HP-UX 11i v2 is the latest Enterprise Release on Itanium-based systems
with extended software solutions and new hardware platforms.
Features and Applications Available in HP-UX 11i v2
The HP-UX 11i v2 release includes the following major features and
enhancements:
•
All Operating Environments: Foundation OE, Enterprise OE,
Mission Critical OE, Minimal Technical OE, and Technical
Computing OE
•
•
•
Support for 64-way capable Itanium-based version of Superdome
with 64-CPU performance scaling
HP-UX Partition Manager support for HP-UX 11i, Windows, and
Linux running in separate partitions
Multi-OS system management for HP-UX, Windows, and Linux
running in separate hard partitions
•
•
Support for 1 terabyte of main memory
Support for all previously released Itanium 2 servers: HP Integrity
rx5670 and HP Integrity rx2600
•
•
•
Cell local memory for Superdome/Itanium-based performance
scalability
PCI and PCI-X Doorbell for one-touch online I/O card removal or
replacement
Six more dynamically tunable kernel parameters: dbc_max_pct,
dbc_min_pct, nflocks, nfile, maxfiles, and fs_symlinks
nPars (hard partitions)
VxFS/VxVM/CVM 3.5 (Veritas File System, Veritas Volume
Manager, Veritas Cluster Manager) with up to 1024 ACLs (Access
Control Lists), 2 terabyte maximum file size, and 4 terabyte
maximum file system size. VxFS is the default file system
Performance improvements in Aries dynamic code translator
(executes PA-RISC binaries on Itanium systems) versus HP-UX 11i
v1.6 (B.11.22)
•
•
•
•
•
•
•
iCOD (instant Capacity on Demand)
Pay Per Use (PPU)
Dynamically Loadable Kernel Modules for File System
Java Virtual Machine (JVM) v1.4.1 with 32- and 64-bit hotspot
Chapter 1
21
Welcome to HP-UX 11i Version 2
What is HP-UX 11i v2?
•
•
•
•
•
HP Workload Manager
HP-UX Bastille for secure system configuration
Faster system boot and memory dump through greater parallelism
Hyperfabric2
Application binary compatibility with previous HP-UX 11i releases
for Itanium (HP-UX 11i v1.5 (B.11.20) and HP-UX 11i v1.6 (B.11.22))
Application source code compatibility with HP-UX 11i v1 on
PA-RISC
•
•
•
•
Dynamic Loader
Interrupt Migration
HP WBEM Services for HP-UX for monitoring and controlling a
diverse set of resources.
•
•
•
•
•
•
•
AutoFS+2.3
On-Line Addition and Replacement of I/O Adapters
IPv6 support
SNAplus2
Mozilla Application Suite (Mozilla is the default browser)
HP-UX Secure Shell
New and improved kernel configuration mechanism
You can find the complete list of applications included in the HP-UX 11i
v2 release in the HP Application Availability Matrix:
http://www.software.hp.com/MATRIX
NOTE
HP is continually adding support for additional hardware and software.
Contact your HP Service Representative for information about
additional support or refer to the latest edition of this document on
http://docs.hp.com.
22
Chapter 1
Welcome to HP-UX 11i Version 2
What is HP-UX 11i v2?
Features Unavailable in HP-UX 11i v2
In comparison with HP-UX 11i v1 or HP-UX 11i v1.6, HP-UX 11i v2 does
not provide support for the following:
•
•
•
•
PA-RISC systems
Virtual Partitions (vPars)
32-bit support
Support of update from HP-UX 11i v1.6 (B.11.22) workstations to
HP-UX 11i v2 (zx2000 and zx6000)
•
•
•
•
•
•
•
Business Copy/BCV/snapshot features on high-end disk arrays
Fabric connectivity with Fibre Channel Mass Storage
OSPF agent for gated
PA-RISC cross development on Itanium-based processors
HP-supplied PA-RISC mode archive system libraries
HP-supplied Itanium-based archived system libraries
Mix and match between Itanium-based and PA-RISC binaries and/or
32-bit and 64-bit objects
•
•
Framebuffer graphics support
Boot from floppy disk
In addition, administrators and developers should make note of the
following important change and limitation:
•
No 32-bit version of this OS will be made available.
TIP
Additional information about these changes, limitations, and differences
between HP-UX 11i v1.6 (B.11.22) and HP-UX 11i v2 (B.11.23) are
described further in the HP-UX 11i Version 2 Release Notes.
Chapter 1
23
Welcome to HP-UX 11i Version 2
Media Kit Contents
Media Kit Contents
This guide is part of the HP-UX 11i v2 media kit. Please review the
contents, which also include the following DVDs and documents:
•
HP-UX 11i v2 (B.11.23) DVD — Contains the HP-UX operating
system (OS), operating environments (OE), required networking
software, Update-UX, Ignite-UX, and online diagnostics.
•
•
HP-UX 11i v2 (B.11.23) Applications DVD — Contains HP-UX
application software.
HP-UX 11i v2 Instant Information DVD — Contains current
HP-UX manuals, release notes, and white papers. See the DVD
booklet for more information.
HP-UX 11i v2 Internet Express DVD — A collection of Open
Source Web, Internet, and security services which have been tested
and qualified on HP-UX. Internet Express is an easily installed,
configured, and administered product.
•
•
Read Before Installing or Updating to HP-UX 11i Version 2 —
Provides last-minute information for HP-UX 11i v2. Read this DVD
booklet before cold-installing, updating, or configuring HP-UX.
HP-UX 11i Version 2 Release Notes — Describes new features and
functionality changes for HP-UX 11i v2. The release notes show the
difference between HP-UX 11i v1.6 and HP-UX 11i v2. After you
cold-install or update HP-UX, this file is on the system in
/usr/share/docs. Release Notes are also available on the Instant
Information DVD and on the web:
http://docs.hp.com/hpux/os/11iv2
•
HP-UX 11i Version 2 Installation and Update Guide —
Describes the media kit, and instructions to cold-install or update to
the latest release of HP-UX. The guide is also available on the web:
http://docs.hp.com/hpux/os/11iv2
NOTE
For the latest information on HP-UX software releases, go to the web:
http://www.software.hp.com/RELEASES-MEDIA
24
Chapter 1
Welcome to HP-UX 11i Version 2
HP-UX 11i v2 Operating Environments
HP-UX 11i v2 Operating Environments
Operating Environments are tested and integrated application bundles
designed to work with the operating system and provide the
functionality needed for your system’s purpose. The following list details
the currently available HP-UX 11i v2 OEs:
•
•
•
HP-UX 11i v2 Foundation Operating Environment (FOE) —
Designed for the demands of Web servers, content servers and
front-end servers, this OE is provided at no-charge and includes
applications such as HP-UX Web Server Suite, Java, and Mozilla
Application Suite. This OE is bundled as HPUX11i-OE.
HP-UX 11i v2 Enterprise Operating Environment (EOE) —
Designed for database application servers and logic servers, this OE
is an extra-cost package containing the HP-UX 11i Foundation OE
and additional applications such as GlancePlus Pak to enable an
enterprise-level server. This OE is bundled as HPUX11i-OE-ENT.
HP-UX 11i v2 Mission Critical Operating Environment
(MCOE) — Designed for the large, powerful back-end application
servers and database servers that access customer files and handle
transaction processing, this OE is an extra-cost package containing
the Enterprise OE, plus applications such as MC/ServiceGuard and
Workload Manager to enable a mission-critical server. This OE is
bundled as HPUX11i-OE-MC.
•
•
HP-UX 11i v2 Minimal Technical Operating Environment
(MTOE) — Designed for workstations running HP-UX 11i v2, this
OE is provided at no charge and includes the Mozilla Application
Suite, Perl, VxVM, and Judy applications, plus the OpenGL
Graphics Developer’s Kit. This OE is bundled as HPUX11i-MTOE
HP-UX 11i v2 Technical Computing Operating Environment
(TCOE) — Designed for both compute-intensive workstation and
MTOE plus extensive graphics applications and Math Libraries.
This OE is bundled as HPUX11i-TCOE.
For more information about the contents of the operating environments,
see Appendix D, “Software Distribution Media,” on page 161.
Chapter 1
25
Welcome to HP-UX 11i Version 2
HP-UX 11i v2 Operating Environments
The following table details the supported operating environments for
servers and workstations:
Table 1-2
Supported Operating Environments
1
FOE
EOE
MCOE
MTOE
TCOE
HP Commercial Servers
X
X
X
X
X
HP Workstations
X
(and Technical Servers)
1. You can use TCOE on either workstations or compute-intensive
technical servers.
Mission Critical OE Support
If your system is on HP Mission Critical Support, discuss the proper
method of cold-installing and updating the OE with your HP Customer
Engineer.
26
Chapter 1
Welcome to HP-UX 11i Version 2
Other Sources of Information about This Release
Other Sources of Information about This
Release
In addition to this guide, you have many other sources of information
related to the HP-UX 11i v2 release available to you at the web site:
http://docs.hp.com/hpux/os/11iv2
The following documents, which are found at this web site, may be of
particular interest:
HP-UX 11i Version 2 Release Notes, MPN 5187-2723
Managing Systems and Workgroups, Edition 6, MPN 5187-2216
Ignite-UX Administrator's Guide, Edition 11 MPN B2355-90788
Software Distributor Administrator's Guide, MPN B2355-90789
Getting Started with Software Package Builder, MPN 5187-3646
HP-UX System Partitions Guide, MPN 5971-4742
Read Before Installing or Updating to HP-UX 11i Version 2, MPN
5187-2734
HP-UX 11i Version 2 Reference, MPN B2355-60103
Additionally, some or all of these documents are available on the Instant
Information media and in printed form.
HP Documentation Web Site
Hewlett-Packard provides a web site where the latest HP-UX
documentation and updates are available:
http://docs.hp.com
HP-UX 11i v2 Instant Information Media
The Instant Information provides HP-UX documentation on media,
either CD or DVD. Documentation supporting the release can be
accessed before the software is installed. It provides improved online
presentation, print quality, and search capabilities.
Chapter 1
27
Welcome to HP-UX 11i Version 2
Other Sources of Information about This Release
HP-UX Welcome Page
The HP-UX Welcome Page on your HP-UX 11i v2 system contains
pointers to information to help you use your HP-UX system.
Manual Pages
For the HP-UX 11i v2 release, the manual (man) pages are available on
the HP-UX Welcome Page of your system, on the Instant Information
under the title HP-UX Reference, through the use of the mancommand,
and on the web:
http://docs.hp.com/hpux/os/11iv2/index.html#HP-UX%20Referenc
e%20(Manpages)
README Documents
README documents are media booklets that contain information about
the installation process that may not appear in the HP-UX 11i Version 2
Installation and Update Guide. Any product contained in the release
may have a README document, so several README documents may be
included. The README document specific for HP-UX 11i v2 is included
with your media kit.
Release Notes
The HP-UX 11i Version 2 Release Notes describe what is new, changed,
or obsolete in this release as compared to previous releases. These
release notes apply only to features that are part of the HP-UX 11i v2
operating system.
The purpose of the HP-UX 11i Version 2 Release Notes is to define the
major differences between HP-UX 11i v1.6 (B.11.22) and HP-UX 11i v2
(B.11.23).
Release notes are found in the following locations:
•
HP-UX 11i v2 Instant Information DVD
• /usr/share/docson your HP-UX 11i v2 system. Also included in
the /usr/share/docsdirectory are files containing information
about previous releases of HP-UX
• http://docs.hp.com
28
Chapter 1
Welcome to HP-UX 11i Version 2
The Next Steps
The Next Steps
•
•
•
•
•
•
•
“Introduction” on page 19
“How to Use This Guide” on page 20
“What is HP-UX 11i v2?” on page 21
“Media Kit Contents” on page 24
“HP-UX 11i v2 Operating Environments” on page 25
“Other Sources of Information about This Release” on page 27
After reading about the media contents and HP-UX, you are now ready
to start reviewing the appropriate method to migrate to HP-UX 11i v2,
either cold-install or update. Continue with the following chapter:
•
Chapter 2, “Choosing a Migration Path,” on page 31
30
Chapter 1
2
Choosing a Migration Path
most appropriate method to migrate your system to HP-UX 11i v2.
•
•
•
•
•
“Migrating from Previous HP-UX Releases” on page 33
“Deciding Which Method to Use” on page 36
“Install-time Security Considerations” on page 43
“The Next Steps” on page 49
To complete the review in this chapter, we estimate you require one hour
to read about the install and update migration paths, security, and
choose a method. Please note that your time may vary.
Chapter 2
31
Choosing a Migration Path
If You Have an Existing HP-UX 11i v2 System
If You Have an Existing HP-UX 11i v2 System
If your system is already running HP-UX 11i v2, you may only need to
install one or more patch bundles to bring your system up-to-date or to
enable new hardware.
Check the following references:
•
“Keeping Up to Date with the Latest Critical Patches” on page 126
• http://itrc.hp.com
• http://software.hp.com
•
Application release notes, readme files, and DVD booklets for the
latest information
32
Chapter 2
Choosing a Migration Path
Migrating from Previous HP-UX Releases
You can cold-install HP-UX 11i v2 and its accompanying operating
environment on any supported system listed in “Supported Servers and
Workstations” on page 56.
You can also choose to update to HP-UX 11i v2 from any of the
supported paths listed in Table 2-1. Updating from any other release
directly to HP-UX 11i v2 is not supported.
Supported Cold-Install Paths to HP-UX 11i v2
Cold-install is supported on both Itanium-based HP servers and
workstations. For a list of supported systems, see “Supported Servers
and Workstations” on page 56.
You can cold-install from most HP-UX 11i v1.6 (B.11.22) systems and all
HP-UX 11i v2 (B.11.23) systems.
IMPORTANT
If you have an LVM-based HP-UX 11i v1.6 system, you can use an
HP-UX 11i v2 Ignite-UX server to cold-install HP-UX 11i v2 on your
system.
If you have an VxVM-based HP-UX 11i v1.6 system, you cannot use an
HP-UX 11i v2 Ignite-UX server to cold-install HP-UX 11i v2 on your
system.
For more details, please see the Ignite-UX web site:
http://software.hp.com/products/IUX
Chapter 2
33
Choosing a Migration Path
Migrating from Previous HP-UX Releases
Supported Update Paths to HP-UX 11i v2
IMPORTANT
Update is only supported on HP Servers (see “Supported Servers and
Workstations” on page 56 for a list of supported servers).
The following table details the supported update migration paths:
Table 2-1
OE Update Migration Paths to HP-UX 11i v2
a
From Current Configuration
To the following HP-UX 11i v2.0 OS/OE
HP-UX 11i v1.6 Base OS
•
•
•
Base OS
Foundation OE
Technical Computing OE (Technical Servers only)
HP-UX 11i v1.6 OE
•
•
Foundation OE
HP-UX 11i v1.6 TCOE
HP-UX 11i v1.6 MTOE
HP-UX 11i v2 Base OS
Technical Computing OE (Servers only)
NO Supported Paths (Cold-install only)
•
•
•
•
•
Base OS
Foundation OE
Enterprise OE
Mission Critical OE
Technical Computing OE
HP-UX 11i v2 Foundation OE
HP-UX 11i v2 Enterprise OE
•
•
•
Foundation OE
Enterprise OE
Mission Critical OE
•
•
Enterprise OE
Mission Critical OE
HP-UX 11i v2 MCOE
HP-UX 11i v2 TCOE
•
•
Mission Critical OE
Technical Computing OE (Servers only)
34
Chapter 2
Choosing a Migration Path
Migrating from Previous HP-UX Releases
Table 2-1
OE Update Migration Paths to HP-UX 11i v2 (Continued)
a
From Current Configuration
To the following HP-UX 11i v2.0 OS/OE
HP-UX 11i v2 MTOE
NO Supported Paths (Cold-install only)
a. Contents of the HP-UX operating environments are listed in Appendix D,
“Software Distribution Media,” on page 161.
Update Path Notes
•
If you are planning to update to a higher level server operating
environment from a current HP-UX 11i v1.6 server operating
environment (for example, HP-UX 11i v1.6 Foundation OE (base OE)
to HP-UX 11i v2 Enterprise OE, you must proceed using the
following steps:
1. Update to HP-UX 11i v2 Foundation OE
2. Update to the desired premium OE (in this case, the Enterprise
OE)
•
•
You cannot downgrade to a lower level operating environment (for
example from Enterprise OE (EOE) to Foundation OE (FOE), or
Technical Computing Operating Environment (TCOE) to Minimum
Technical Operating Environment (MTOE)
You cannot update between server operating environments (FOE,
EOE, and MCOE) and technical operating environments (MTOE,
and TCOE)
Chapter 2
35
Choosing a Migration Path
Deciding Which Method to Use
Deciding Which Method to Use
Now that you have evaluated your system and ordered any additionally
needed hardware, you need to decide whether to cold-install or update
to HP-UX 11i v2 on your system.
Cold-installing using Ignite-UX — This method overwrites
everything on the target disk. Use cold-install for new systems and on
existing systems when overwriting the root (/) volume will not cause loss
of applications or data. The process described in this guide cold-installs a
single system from local media. If you plan to install many systems
simultaneously, you should plan on using an Ignite-UX server. Ignite-UX
is available on the HP-UX 11i v2 DVD. Additional information on
Ignite-UX and newer versions are available on this web site:
http://software.hp.com/products/IUX
command and Software Distributor (SD) tools to selectively overwrite
the operating system and application software from media or a network
source depot. An advantage of performing an update is that it leaves user
data, configuration, and applications in place. Updating to HP-UX 11i v2
is limited to the supported paths listed in Table 2-1, “OE Update
Migration Paths to HP-UX 11i v2,” on page 34.
Depending on your system’s current configuration, here are some
general guidelines to help you choose the best migration path to HP-UX
11i v2.
When to Cold-Install
We recommend using Ignite-UX to cold-install HP-UX 11i v2 in the
following situations:
•
•
•
You are managing several systems with similar OS configurations.
You need fast, predictable deployment.
Your disk space needs reconfiguration. See “How to Plan Your Disk
Space Needs” on page 55.
•
Your systems are organized with clean separation of the OS from
user, application, and data files.
36
Chapter 2
Choosing a Migration Path
Deciding Which Method to Use
•
•
(see Table 2-1, “OE Update Migration Paths to HP-UX 11i v2,” on
page 34).
You can cold-install from any supported configuration (see “Supported
Servers and Workstations” on page 56).
See Chapter 4, “Preparing to Migrate to HP-UX 11i v2,” on page 63 for
more information about preparing your system for cold-install. Then the
When to Update
You can update rather than cold-install HP-UX 11i v2 when you are
updating from supported HP-UX 11i v1.6 systems or from HP-UX 11i v2
(see Table 2-1, “OE Update Migration Paths to HP-UX 11i v2,” on
page 34 for specific details). Other scenarios include:
•
your root volume, and do not want to write over non-OS files when
cold-installing HP-UX 11i v2.
•
•
Each system has a unique configuration.
Current disk space is sufficient for HP-UX 11i v2 (see “How to Plan
NOTE
Update is not supported on HP Workstations.
See Chapter 4, “Preparing to Migrate to HP-UX 11i v2,” on page 63 for
details on how to prepare your system to update to HP-UX 11i v2. Then
Installing Network Drivers
Installing HP-UX 11i v2 will install a minimum set of default
networking drivers that apply to the system (see Table D-4, “HP-UX 11i
v2 Always-Installed Network Drivers,” on page 174).
Chapter 2
37
Choosing a Migration Path
Deciding Which Method to Use
You may need to select or specify other available networking drivers to
enable other cards on your system (see “HP-UX 11i v2 Always-Installed
Network & Mass Storage Drivers” on page 174). This can easily be done
during the cold-install or update by following the instructions in
“Cold-installing HP-UX 11i v2” on page 83.
Cold-Install Considerations
The following sections provide additional information to assist you in
your decision to cold-install HP-UX 11i v2.
HP Service Partition
During cold-install or recovery, Ignite-UX will change the boot disk
partition layout to create a new HP Service Partition (HPSP). This
400MB partition created at the end of the boot disk is used by Online and
Offline Diagnostics to hold tools and system data.
The order of the partitions on the boot disk will be:
1. EFI OS Boot Partition (ESP)
2. HP-UX File System (HPUX)
3. HP Service Partition (HPSP)
During back-up and recovery operations, Ignite-UX will not save or
restore any changes you make to the HPSP.
Instant Ignition
For customers ordering new systems with the “Instant Ignition” option
(also known as “factory integrated”), the cold-installation process
described here has already been performed. Skip this chapter and
proceed to install application software. See Chapter 8, “Installing
Patches and Applications,” on page 125.
38
Chapter 2
Choosing a Migration Path
Deciding Which Method to Use
Alternate Cold-Install Methods
In addition to the procedures described in this chapter, you can
cold-install your system using the following methods:
•
Install from Software Depots
Use Software Distributor commands to create depots containing OS,
OE, and other software bundles, then install from the depot using
Ignite-UX. For help with this method, see the swinstall (1M)
manpage and Software Distributor Administration Guide and
Ignite-UX Administration Guide.
•
Install from Golden Images
If you need to install the same OS/OE and applications on many
systems in your network, use an Ignite-UX server as explained in the
Ignite-UX Administration Guide. With Ignite-UX, you can create a
single install image (golden image) containing OS/OE bundles,
application bundles, and patch bundles, then install the image on
multiple systems in your environment.
IMPORTANT
Please note that if you are running an Ignite-UX server on HP-UX 11i v2
and have HP-UX Bastille enabled, then cold-installing a golden image
onto another system will require additional steps. For the latest
information, please see the following web site:
http://www.software.hp.com/products/IUX
Using the HP-UX 11iv2 DVDs on an HP-UX 11iv1 (B.11.11) System
If you plan to read the HP-UX 11iv2 DVDs on an HP-UX 11iv1 system,
or cold-install HP-UX 11iv2 from a depot on an HP-UX 11iv1 system,
then you need to install the PHKL_28025patch in order to read the DVDs.
The PHKL_28025patch is in the GOLDBASE11ibundle as of June 2003,
which you can find on the Support Plus media for HP-UX 11iv1 or at the
following web site:
http://itrc.hp.com
PHKL_28025supersedes PHKL_25760.
Chapter 2
39
Choosing a Migration Path
Deciding Which Method to Use
Update Considerations
HP Service Partition Is Not Created During Update
If you are updating from a supported update path (see “Supported
Update Paths to HP-UX 11i v2” on page 34), HP Service Partition will
not be created or modified. OnlineDiagwill continue to work properly.
Offline Diagnostics, however, will work with reduced functionality.
In order to have full Offline Diagnostics functionality, you must:
1. Update your system.
2. Back up your system with either make_net_recoveryor
make_tape_recovery.
3. Re-configure your boot disk partition layout to include the HP
Service Partition.
4. Restore your system with either make_net_recoveryor
for more details about make_net_recoveryand
make_tape_recovery.
5. Update the Offline Diagnostics with the latest version of the HP
Itanium-Processor Family Offline Diagnostics and Utilities CD. See
“About Offline Diagnostics” on page 71.
How to Determine If You Have an HP Service Partition
To determine if an HP Service partition exists on your system, enter the
following command on your physical disk volume (here named
/dev/rdsk/c2t1d0):
idisk -p /dev/rdsk/c2t1d0
Example 2-1
idisk Output from Disk without HP Service Partition
idisk version: 1.31
EFI Primary Header:
Signature
= EFI PART
= 0x10000
= 0x5c
Revision
HeaderSize
HeaderCRC32
MyLbaLo
= 0x20e10a24
= 0x1
40
Chapter 2
Choosing a Migration Path
Deciding Which Method to Use
AlternateLbaLo
FirstUsableLbaLo
LastUsableLbaLo
Disk GUID
= 0x43d671f
= 0x22
= 0x43d66fc
= 59609df4-c295-11d7-8001-d6217b60e588
= 0x2
PartitionEntryLbaLo
NumberOfPartitionEntries = 0xc
SizeOfPartitionEntry = 0x80
PartitionEntryArrayCRC32 = 0xc0a93cc2
Primary Partition Table (in 512 byte blocks):
Partition 1 (EFI):
Partition Type GUID
Unique Partition GUID
Starting Lba
= c12a7328-f81f-11d2-ba4b-00a0c93ec93b
= 5960a1be-c295-11d7-8002-d6217b60e588
= 0x22
Ending Lba
= 0xfa021
Partition 2 (HP-UX):
Partition Type GUID
Unique Partition GUID
Starting Lba
= 75894c1e-3aeb-11d3-b7c1-7b03a0000000
= 5960a1fa-c295-11d7-8003-d6217b60e588
= 0xfa022
Ending Lba
= 0x430e021
You should notice that under the “Primary Partition Table (in 512
byte blocks)” heading, only two partitions exist on the system: the EFI
boot partition, and the HP-UX partition. This example shows that you
v2.
Default-Installed Bundles Cannot Be Deselected
There is currently no support for deselecting default-installed bundles
(see Appendix D, “Software Distribution Media,” on page 161) from
Update-UX. Consequently, all default-installed bundles will be installed
with the Operating Environment.
Using the HP-UX 11iv2 DVDs on an HP-UX 11iv1 (B.11.11) System
If you plan to read the HP-UX 11iv2 DVDs on an HP-UX 11iv1 system,
or update HP-UX 11iv2 from a depot on an HP-UX 11iv1 system, then
you need to install the PHKL_28025patch in order to read the DVDs.
Chapter 2
41
Choosing a Migration Path
Deciding Which Method to Use
The PHKL_28025patch is in the GOLDBASE11ibundle as of June 2003,
which you can find on the Support Plus media for HP-UX 11iv1 or at the
following web site:
http://itrc.hp.com
NOTE
PHKL_28025supersedes PHKL_25760.
42
Chapter 2
Choosing a Migration Path
Install-time Security Considerations
Install-time Security Considerations
Beginning with HP-UX 11i v2, HP-UX Bastille (B6849AA) is included as
default-installed software on the Operating Environment media and can
be installed with Ignite-UX or Update-UX.
HP-UX Bastille is a security hardening/lockdown tool that can be used to
enhance security of the HP-UX operating system. It provides customized
lockdown on a system-by-system basis by encoding functionality similar
to Bastion Host and other hardening/lockdown checklists.
NOTE
For more information about HP-UX Bastille, see the HP-UX 11i Version
2 Release Notes and Managing Systems and Workgroups.
At install- or update-time, you can choose one of the following security
configuration bundles with each bundle providing incrementally higher
security:
Table 2-2
Predefined Security Configuration Bundles
Configuration
File Name
Bundle
Name
Description
a
b
-
The install-time security infrastructure; no security
changes
Sec00Tools
c
HOST.config
Host-based lockdown: no firewall; many some common
clear-text services turned off, excluding Telnet and
FTP
Sec10Host
c
MANDMZ.config
DMZ.config
Lockdown: IPFilter firewall blocks incoming
connections except common, secured, management
protocols
Sec20MngDMZ
c
Full lockdown: IPFilter blocks all incoming
connections except HP-UX Secure Shell
Sec30DMZ
a. Configuration files are installed to /etc/opt/sec_mgmt/bastille.
b. This is a default-installed bundle.
c. This is a selectable bundle.
Chapter 2
43
Choosing a Migration Path
Install-time Security Considerations
Security Choice Dependencies
The Sec00Toolssecurity infrastructure bundle is default-installed on
your system. While this bundle does not implement any security changes
at install- or update-time, it does ensure that the required software (see
Figure 2-1) is installed. By installing Sec00Tools, you can opt to run
HP-UX Bastille at a later time to lock down your system.
Alternately, you can lock down your system using one of the following
selectable security configuration bundles at install- or update-time:
• Sec10Host
• Sec20MngDMZ
• Sec30DMZ
These bundles are dependent on the Sec00Toolsbundle.
Figure 2-1
Install-time Security Software Dependencies
These selectable bundles lock down your
system at install- or update-time. They
depend on Sec00Tools to install the needed
software to secure your system.
Sec30DMZ
Sec20MngDMZ
Sec00Tools
Sec10Host
This default-installed bundle does not apply
any security at install- or update-time.
Instead, it ensures that the following required
bundles are installed.
Security
Patch
Check
HP-UX
Secure
Shell
IPFilter
HP-UX
Bastille
This default-installed software is required
to secure your system either at install-time
or at a later time.
perl
Selectable security bundles
Default-installed bundles
44
Chapter 2
Choosing a Migration Path
Install-time Security Considerations
Secured Services and Protocols
Each security configuration bundle provides incrementally higher
uses a series of questions to determine which services and protocols to
applies a default security profile, simplifying the lockdown process.
or update-time.
•
•
•
Table 2-4 lists the security settings applied with Sec20MngDMZ,
additional to the settings in Table 2-3
Table 2-5 lists the security settings applied with Sec30DMZ. These
settings are additional to the settings applied in Table 2-3 and
Table 2-4
IMPORTANT
Review these tables carefully. Some of the locked down services and
protocols may be used by other applications, and may have adverse
effects on the behavior or functionality of these applications. For
example, ServiceControl Manager and ParMgr rely on WBEM for part of
their functionality; Sec30DMZblocks all incoming WBEM connections via
IPFilter.
You can change the security settings configured at install-time by
running HP-UX Bastille after installing or updating your system. For
more information about using HP-UX Bastille, see the Managing
Systems and Workgroups manual, or the HP-UX Bastille User’s Guide,
located on your system at
/opt/sec_mgmt/bastille/docs/user_guide.txt
Chapter 2
45
Choosing a Migration Path
Install-time Security Considerations
a
Table 2-3
Host-based Sec10HostInstall-time Security Settings
Category Actions
Logins and
Deny login unless home directory exists
Deny non-root logins if /etc/nologinfile exists
Set a default path for su command
Disable root logins from network tty
Hide encrypted passwords
Passwords
Disallow ftpdsystem account logins
Disable remote X logins
b,c
File System,
Modify nddsettings
Network, and Kernel
Restrict remote access to swlist
Set default umask
Enable kernel-based stack execute protection
Disable ptydaemon
Daemons
Disable pwgrd
Disable rbootd
Disable NFS client daemons
Disable NFS server
Disable NIS client programs
Disable NIS server programs
Disable SNMPD
Deactivate bootp
inetd Services
Deactivate inetd’s built-in services
Deactivate CDE helper services
Deactivate finger
Deactivate ident
Deactivate kloginand kshell
Deactivate ntalk
Deactivate login, shell, and execservices
Deactivate swat
Deactivate printer
Deactivate recserv
Deactivate tftp
Deactivate time
Deactivate uucp
Enable logging for all inetdconnections
Run sendmailvia cronto process queue
Stop sendmailfrom running in daemon mode
Disable vrfyand expncommands
sendmail
46
Chapter 2
Choosing a Migration Path
Install-time Security Considerations
a
Table 2-3
Host-based Sec10HostInstall-time Security Settings (Continued)
Category
Actions
d
Other Settings
Deactivate HP Apache 2.x Web Server
b
Set up cronjob to Security Patch Check
a. Security settings listed here also apply to Sec20MngDMZand Sec30DMZ
b. Manual action may be required to complete configuration. See
/etc/opt/sec_mgmt/bastille/TODOfor more information, after install or
update.
c. The following nddchanges will be made:
ip_forward_directed_broadcasts=0
ip_forward_src_routed=0
ip_forwarding=0
ip_ire_gw_probe=0
ip_pmtu_strategy=1
ip_send_source_quench=0
tcp_conn_request_max=4096
tcp_syn_rcvd_max=1000
d. Settings only applied if software is installed
a
Table 2-4
Additional Sec20MngDMZInstall-time Security Settings
Category
Actions
inetd Services
Includes all disabled inetd services in Table 2-3
and:
Deactivate ftp
Deactivate telnet
Block incoming DNS query connections
IPFilter
b
c,d
Configuration
Configure IPFilter to allow outbound traffic, block
incoming traffic with IP options set, and all other traffic
except for HP-UX Secure Shell, HIDS agent, WBEM,
e
web admin and web admin autostart.
a. Applies all security configuration settings in Table 2-3
b. IPFilter rules are applied via a custom rules file located at
/etc/opt/sec_mgmt/bastille/ipf.customrules
c. HP-UX Host IDS is a selectable software bundle and only available for commercial
servers
d. Settings only applied if software is installed
Chapter 2
47
Choosing a Migration Path
Install-time Security Considerations
e. Manual action may be required to complete configuration. See
/var/opt/sec_mgmt/bastille/TODO.txtfor more information, after install or
update.
a
Table 2-5
Additional Sec30DMZInstall-time Security Settings
Category
Actions
IPFilter
Configuration
Includes all IPFilter settings in Table 2-4 and:
b
c,d
Block incoming HIDS agent connections
e
Block incoming WBEM connections
Block incoming web admin connections
Block incoming web admin autostart connections
Block all traffic except HP-UX Secure Shell
a. Applies all security configuration settings in Table 2-3 and Table 2-4
b. IPFilter rules are applied via a custom rules file located at
/etc/opt/sec_mgmt/bastille/ipf.customrules
c. Settings only applied if software is installed
d. HP-UX Host IDS is a selectable software bundle and only available for commercial
servers
e. WBEM is required for several HP management applications including
ServiceControl Manager and ParMgr
48
Chapter 2
Choosing a Migration Path
The Next Steps
The Next Steps
•
•
•
•
“If You Have an Existing HP-UX 11i v2 System” on page 32
“Migrating from Previous HP-UX Releases” on page 33
“Deciding Which Method to Use” on page 36
“Install-time Security Considerations” on page 43
After deciding which method you will use to migrate to HP-UX 11i v2,
you are ready to start preparing your system for either cold-install or
update:
•
Chapter 4, “Preparing to Migrate to HP-UX 11i v2,” on page 63
IMPORTANT
Be sure to review the Read Before Installing or Updating to HP-UX 11i
v2 DVD booklet for situations not discussed in this chapter that may
apply to your system.
Chapter 2
49
Choosing a Migration Path
The Next Steps
50
Chapter 2
3
Installing and Updating System
Requirements
to cold-installing or updating to HP-UX 11i v2.
•
•
•
•
page 57
•
•
•
“Keeping Up with Firmware Recommendations” on page 58
“Identifying Model, OS/OE, and Software” on page 60
“The Next Steps” on page 62
IMPORTANT
Review the Read Before Installing or Updating to HP-UX 11i v2 DVD
booklet. It describes last-minute information.
To complete the steps in this chapter, we estimate you require 1 hour to
compare the system requirements specified in this guide with your
system. Please note that your time may vary.
Chapter 3
51
Installing and Updating System Requirements
Factory Ignited Systems
Factory Ignited Systems
If you have a system that is already running HP-UX 11i v2, such as a
system that was factory ignited, you may only need to check for the
latest, critical patches to have the most up-to-date system.
Check the following references:
•
“Keeping Up to Date with the Latest Critical Patches” on page 126
• http://itrc.hp.com
• http://software.hp.com
•
Application release notes and readme booklets for the latest
information
52
Chapter 3
Installing and Updating System Requirements
System Requirements
System Requirements
To cold-install or update HP-UX 11i v2, you must have the following:
•
Supported system, see “Supported Servers and Workstations” on
page 56
•
•
•
•
HP-UX 11i v2 OE and application media (two DVD set)
512 MB memory, minimum
1 GB swap space, minimum
1 GB disk space to accommodate EFI Boot Disk and HP Service
Partition
NOTE
If your system has less than 1GB of memory, you may need to manually
set VxFS tunables for optimal performance after cold-installing or
updating to HP-UX 11i v2. For more information about these tunables
see Appendix C, “Controlling Memory Utilization of VxFS 3.5 on HP-UX
11i v2,” on page 155.
Extra space
Cold-installing or updating the HP-UX 11i v2 Technical Computing OE
needed with TCOE and the Minimal Technical OE installs all CDE languages, rather than
and MTOE
just a selected language. To remove unneeded CDE language bundles
after installing the TCOE or MTOE list them using swlistand remove
unneeded bundles using swremove. See Chapter 7, “Verifying System
Install or Update,” on page 117 for example uses of swlistand
swremove.
Disk Space Allocation for File Partitions
Depending on your system’s purpose, you may need to determine how
much disk space you will need for each file partition before you
cold-install or update to HP-UX 11i v2. For example, if you plan to install
applications from other vendors, you may need to modify the size of the
/optpartition to accommodate for their size.
Chapter 3
53
Installing and Updating System Requirements
System Requirements
The following table lists the amount of disk space allocated for the
following partitions during a default cold-install for each operating
environment (percentage used in each partition in parentheses):
1
Table 3-1
File Partition Disk Space Allocation by Operating Environment
Partition
FOE
EOE
MCOE
208 MB
TCOE
208 MB
MTOE
223 MB
/
208 MB
208 MB
(78% used)
(81% used)
(81% used)
(77% used)
(83% used)
/stand
/var
304 MB
(21% used)
304 MB
(21% used)
304 MB
(21% used)
304 MB
(21% used)
300 MB
(23% used)
4.5 GB
4.5 GB
4.5 GB
4.5 GB
1.5 GB
(2% used)
(2% used)
(2% used)
(2% used)
(6% used)
/usr
2.6 GB
2.7 GB
2.7 GB
3.7 GB
3.7 GB
(76% used)
(75% used)
(75% used)
(61% used)
(62% used)
/tmp
208 MB
208 MB
208 MB
208 MB
200 MB
(4% used)
(4% used)
(4% used)
(4% used)
(4% used)
/opt
3.6 GB
3.7 GB
3.7 GB
4.5 GB
2.7 GB
(52% used)
(53% used)
(53% used)
(58% used)
(63% used)
/home
32 MB
32 MB
32 MB
32 MB
20 MB
(26% used)
(26% used)
(26% used)
(26% used)
(41% used)
2,3
11.6 GB
(37% used) (37% used)
11.7 GB
11.8 GB
(36% used)
13.7 GB
(38% used)
8.7 GB
(50% used)
Total
1. The results are from using the bdf (1M)command; your results may vary if you
use the du (1) command.
2. Totals are not exact due to rounding
3. Totals do not include disk space required for the EFI Boot Partition, HP Service
Partition, or /swap
Depending on how much disk space you have available, you can change
the size of the partitions to meet your system’s needs. For more
information about modifying your file system, see Managing Systems
and Workgroups: A Guide for HP-UX System Administrators.
54
Chapter 3
Installing and Updating System Requirements
System Requirements
Update Disk Space Requirements
To ensure a successful update to HP-UX 11i v2, you will need to make
sure that you have at least as much disk space allocated to the file
partitions listed in Table 3-1, and each partition (most importantly,
/usr,/optand /var) has at least 10-20% free space to allow for any
growth. Additionally, make sure that you have at least 1 GB allocated for
/swap.
How to Plan Your Disk Space Needs
This section provides hints and information to help you determine your
disk needs for HP-UX 11i v2. If you need more disk space, be sure to
order the equipment and plan on installing it after backing up your
current system.
Planning Hints
•
•
Record the hardware path to the DVD drive.
Develop a clear configuration plan, including:
— File system sizes
— Swap space size
— Dump device
— Disk and file-system parameters
— Mirroring information
•
•
If installing application programs other than those supplied within
an HP-UX 11i v2 Operating Environment (OE), consider the vendor’s
size recommendations.
When planning disk space, refer to these books:
— Managing Systems and Workgroups: A Guide for HP-UX System
Administrators — This manual is available on the Instant
Information DVD and the web:
http://docs.hp.com
— Disk and File Management Tasks on HP-UX — Prentice-Hall
Hewlett-Packard Professional Books, 1997.
Chapter 3
55
Installing and Updating System Requirements
Supported Servers and Workstations
Supported Servers and Workstations
HP-UX 11i v2 (B.11.23) supports only a 64-bit version of the HP-UX
kernel. The HP-UX 11i v2 release fully supports the following servers
and workstations:
•
•
•
•
•
•
•
•
HP Integrity rx2600 (HP server)
HP Integrity rx4640 (HP server)
HP Integrity rx5670 (HP server)
HP Integrity rx7620 (HP server)
HP Integrity rx8620 (HP server)
HP Integrity Superdome (HP servers: 16-, 32-, and 64-way))
zx2000 (HP workstation)
zx6000 (HP workstation)
NOTE
For additional information, including specifications, warranty, and
support go to the web:
http://www.hp.com/products1/itanium
Unsupported Servers and Workstations
HP-UX 11i v2 is not supported on the following platforms:
•
•
•
PA-RISC platforms
i2000 (HP workstation)
HP Integrity rx4610 (HP server)
56
Chapter 3
Installing and Updating System Requirements
HP-UX 11i v2 Network, Mass Storage, and SCSI Drivers
HP-UX 11i v2 Network, Mass Storage, and
SCSI Drivers
The HP-UX 11i Version 2 Release Notes provides a complete list of
supported network and mass storage drivers, and SCSI devices. See
documentation for the products.
Additionally, the following sections list the network and mass storage
drivers, and supported I/O adapters included with HP-UX 11i v2:
•
“HP-UX 11i v2 Always-Installed Network & Mass Storage Drivers”
on page 174
•
“HP-UX 11i v2 Selectable Network Drivers” on page 178
Chapter 3
57
Installing and Updating System Requirements
Keeping Up with Firmware Recommendations
Keeping Up with Firmware Recommendations
Pre-Migration Task Firmware changes frequently. It is important to make sure your system
for Everyone
has the latest firmware installed in order, for example, to support the
latest versions of I/O adapters, mass storage devices, and devices used
when you install from media or a network depot.
NOTE
To make sure your system has the latest firmware, check this web site:
http://www.hp.com/support/itaniumservers
Table 3-2
System
Firmware for the First Release of HP-UX 11i v2 Systems
Platform
Baseboard
Management
Controller
(BMC)
Manage-
ment
Manufac-
turing
Dependent
Hardware
Controller
(PDHC)
System
Processor
(MP)
Firmware
(MFW)
Firmware
HP Integrity
rx2600 (HP
server)
1.50
2.18
1.30
MP E.02.10
or E.02.23
2.21
HP Integrity
rx4640 (HP
server)
E.02.23
E.02.23
1.10
HP Integrity
rx5670 (HP
server)
3.20
HP Integrity
rx7620 (HP
server)
Core I/O
MP: 5.10
3.6
3.6
0.18.0
0.18.0
HP Integrity
rx8620 (HP
server)
Core I/O
MP: 5.10
58
Chapter 3
Installing and Updating System Requirements
Keeping Up with Firmware Recommendations
Table 3-2
Firmware for the First Release of HP-UX 11i v2 Systems
Platform
Dependent
Hardware
Controller
(PDHC)
Baseboard
Management
Controller
(BMC)
Manage-
ment
Processor
(MP)
Manufac-
turing
Firmware
(MFW)
System
Firmware
System
HP Integrity
Superdome
(HP servers:
16-, 32-, and
64-way)
14.12
1.12
zx2000
(HP
workstation)
1.50
1.50
2.21
2.21
zx6000
(HP
MP E.02.10
or E.02.23
workstation)
Chapter 3
59
Installing and Updating System Requirements
Identifying Model, OS/OE, and Software
Identifying Model, OS/OE, and Software
Before you cold-install or update to HP-UX 11i v2, check the model and
other information on the system. You can use this information in the
Identifying model To determine the model number of your system, enter:
model
To verify that HP-UX 11i v2 is supported on your system see “Supported
Servers and Workstations” on page 56.
From EFI you can identify the model by interrupting the autoboot
process in the boot manager, entering the EFI shell, and using the
info syscommand:
Shell> info sys
The sample output should appear as follows:
SYSTEM INFORMATION
Product Name: server rx2600
Serial Number: sg20220034
UUID: FFFFFFFF-FFFF-FFFF-FFFF-FFFFFFFFFFFF
Identifying OS and To identify the OS version that your system is currently running, enter:
OE
uname -r
When a system has HP-UX 11i v2 installed, you can determine which
revision (Release ID) is installed by entering the following command:
/usr/sbin/swlist -l bundle
The HPUXBaseAuxbundle indicate the current installed revision level.
The revision level is indicated both in the bundle version number and the
description text.
To identify the Operating Environment currently installed on your
system, use swlist. For example:
/usr/sbin/swlist
The output of this command includes a line which identifies the installed
OE. For example, this HP-UX 11i v2 OE release generates this line:
HPUX11i-OE B.11.23 HP-UX 11i Operating Environment Component
60
Chapter 3
Installing and Updating System Requirements
Identifying Model, OS/OE, and Software
Identifying
To identify the software products on a system or media, use swlist. For
installed software example, to show revision and descriptive title of all software installed
on a system, enter:
/usr/sbin/swlist
For example, to list all products and their versions on a DVD mounted at
/cdrom, enter:
/usr/sbin/swlist -s /cdrom
To get table of contents and product details, enter:
/usr/sbin/swlist -dvl product -a readme @ /cdrom
The swlistcommand has many options to expand or narrow the listing
to specific attributes; see the swlist (1M) manpage or the Software
Distributor Administrator Guide, available on the Instant Information
DVD and on this web site: http://docs.hp.com/hpux/os/11iv2
NOTE
The cold-install process will erase all software on the root volume before
installing HP-UX 11i v2. If you wish to retain any existing software, be
sure to back up that software before migrating, or use update.
Chapter 3
61
Installing and Updating System Requirements
The Next Steps
The Next Steps
•
•
•
•
“HP-UX 11i v2 Network, Mass Storage, and SCSI Drivers” on
page 57
•
•
“Identifying Model, OS/OE, and Software” on page 60
Continue with the next chapter:
Chapter 4, “Preparing to Migrate to HP-UX 11i v2,” on page 63
•
62
Chapter 3
4
Preparing to Migrate to HP-UX
11i v2
update to HP-UX 11i v2.
•
•
•
•
•
•
•
•
“Update Tasks” on page 64
“Backing Up Your System” on page 72
“Saving Configuration Files” on page 75
“Locating Source Media and Codewords” on page 76
“The Next Steps” on page 78
To complete the preparation in this chapter, we estimate you require 2
hours. Please note that your time may vary.
Chapter 4
63
Preparing to Migrate to HP-UX 11i v2
Update Tasks
Update Tasks
Prior to updating to HP-UX 11i v2, you should perform these tasks:
•
•
•
Recording Software Versions
Rebuilding the Kernel
Cleaning Out Your Log Files
Recording Software Versions
To identify what software still needs updating after the OS update, print
a swlistlisting of all products and bundles prior to the update. For
example, enter:
/usr/sbin/swlist | lp
Then compare it with a similar swlistexecuted after the update.
Rebuilding the Kernel
Your update could fail if the HP-UX kernel build fails in the starting
environment. To ensure that you have a reliable starting point, rebuild
the kernel before you update:
1. As root, enter:
/usr/sbin/mk_kernel
2. Fix any problems listed in the mk_kerneloutput.
3. Reboot your system to ensure that your new kernel boots.
Cleaning Out Your Log Files
To make it easier to check for problems encountered during an update,
rename the log files before starting an update:
1. cd /var/adm/sw
2. As root, rename each log file. For example:
mv swagent.log swagent_old.log
64
Chapter 4
Preparing to Migrate to HP-UX 11i v2
Updating Your Ignite-UX Server
Updating Your Ignite-UX Server
The HP-UX 11i v2 DVD contains the complete Ignite-UX product. When
you cold-install HP-UX 11i v2 from the media, a subset of Ignite-UX is
used to perform the installation on a single system.
If you plan to update an existing Ignite-UX server to install HP-UX 11i
v2 on more than one system in your network, then you should update
your Ignite-UX server first.
Updating your Ignite-UX server and using it to update other systems
will ensure that you have the make_net_recoveryand
make_tape_rcoverycommands to backup and recover your systems (see
the make_net_recovery (1M) and make_tape_recovery (1M) manpages for
information). You will also be assured of keeping consistent kernel
configuration with specific drivers, daemons, and kernel tunables on all
systems.
The latest Ignite-UX software and documentation can also be
downloaded from HP via this web site:
http://software.hp.com/products/IUX
Chapter 4
65
Preparing to Migrate to HP-UX 11i v2
Selecting Your HP-UX Console
Selecting Your HP-UX Console
HP-UX requires that you select the correct console via a firmware
selection menu. If you have ordered a machine with HP-UX
pre-installed, your console selections will be correctly chosen for you. If
you are already on the system console, then you can skip this section.
However, if you are cold-installing HP-UX, or change your system
configuration, you may need to select the correct console. Skipping this
step can result in HP-UX using an unexpected device as a console, and
can therefore appear as a system hang.
IMPORTANT
Do not select more than one console device. HP-UX 11i v2 only recognizes
one device at a time. Choosing more than one device may result in the
appearance of system hang.
Step 1. Decide what console you want to use.
Depending on your system configuration, HP-UX can use one of several
possible devices as your system console. The possibilities are:
•
•
•
System Serial Port
Management Processor (MP) Serial Port (if present)
VGA device (if present)
Step 2. Using the EFI menus, select the appropriate console device and deselect
others:
1. Choose the “Boot option maintenance menu” choice from the main
Boot Manager Menu:
EFI Boot Manager ver 1.10 [14.57] Firmware ver 1.20 [4225]
Please select a boot option
HP-UX Primary Boot: 0/2/2/0.0.0.0
EFI Shell [Built-in]
Boot option maintenance menu
Security/Password Menu
66
Chapter 4
Preparing to Migrate to HP-UX 11i v2
Selecting Your HP-UX Console
2. Choose “Select Active Console Output Devices”:
EFI Boot Maintenance Manager ver 1.10 [14.57]
Main Menu. Select an Operation
Boot from a File
Add a Boot Option
Delete Boot Option(s)
Change Boot Order
Manage BootNext setting
Set Auto Boot TimeOut
Select Active Console Output Devices
Select Active Console Input Devices
Select Active Standard Error Devices
Cold Reset
Exit
SystemGuid-->[FFFFFFFF-FFFF-FFFF-FFFF-FFFFFFFFFFFF]
SerialNumber-->[(null)]
3. Choose the correct output device and deselect others. On the HP
Integrity rx2600, HP Integrity rx5670, and zx6000 systems, the
“Select Active Console Output Devices” menu will look like this (see
“Interface Differences between Itanium-based Systems” on page 68
for details about choosing the appropriate device):
EFI Boot Maintenance Manager ver 1.10 [14.57]
Select the Console Output Device(s)
Acpi(PNP0501,0)/Uart(9600 N81)/VenMsg(PcAnsi)
Acpi(PNP0501,0)/Uart(9600 N81)/VenMsg(Vt100)
Acpi(PNP0501,0)/Uart(9600 N81)/VenMsg(Vt100+)
Acpi(PNP0501,0)/Uart(9600 N81)/VenMsg(VtUtf8)
Acpi(HWP0002,700)/Pci(1|1)/Uart(9600 N81)/VenMsg(PcAnsi)
Acpi(HWP0002,700)/Pci(1|1)/Uart(9600 N81)/VenMsg(Vt100)
Acpi(HWP0002,700)/Pci(1|1)/Uart(9600 N81)/VenMsg(Vt100+)
Acpi(HWP0002,700)/Pci(1|1)/Uart(9600 N81)/VenMsg(VtUtf8)
* Acpi(HWP0002,700)/Pci(2|0)
Acpi(HWP0003,400)/Pci(0|0)
Save Settings to NVRAM
Exit
Chapter 4
67
Preparing to Migrate to HP-UX 11i v2
Selecting Your HP-UX Console
Interface Differences between Itanium-based Systems
Each Itanium-based system has a similar interface with minor
differences. You can navigate these menus with the arrow keys or “v”
and “^” keys to move around, and use the enter or space key to select and
deselect devices. Selected devices have an asterisk (“*”) next to them.
After making your changes to this menu, choose Save Settings to
NVRAMand then Exit.
VGA Consoles
Any device in the output device menu that has a Pcisection in its path,
but does not have a Uartsection will be a VGA device. If you require a
VGA console, choose this device, and unmark all others. In the example
above, a VGA device is selected as the console.
Other Console
Types
Any device in the output device menu that has a Uartsection, but no Pci
section is one of the system serial ports; devices containing both a Uart
and Pcisection are MP serial ports. Notice that there are actually four
almost identical system serial ports in the example above. The first four
entries are identical except for their VenMsgsection. This means that
each entry is actually the same device, with different protocols for
accessing the device. If the first entry is chosen, an Ansi capable terminal
device should be used to talk to the serial port. If the second entry is
chosen, a Vt100 capable terminal device should be used, and so on.
If you choose either a system or MP serial port, HP recommends you
choose a Vt100+ capable terminal device.
Selecting a Console on the HP Integrity rx2600,
rx5670, and zx6000 Systems
On the HP Integrity rx2600, HP Integrity rx5670, and zx6000 systems,
an entry in the output device menu that has a Uartsection and a Pci
section will be the serial port on a Management Processor (MP). To use
the MP as your console device, select one of the MP serial device entries,
and deselect everything else.
Step 1. Choose Select Active Console Input Devices.
Step 2. Choose the correct input device and deselect others.
68
Chapter 4
Preparing to Migrate to HP-UX 11i v2
Selecting Your HP-UX Console
Follow all the substeps in Step 2 of “Selecting Your HP-UX Console” on
page 66 to correctly select your console input device. For input devices, a
Step 3. Choose Select Active Standard Error Devices.
Step 4. Choose the correct standard error device and deselect others.
Follow all the substeps in Step 2 of “Selecting Your HP-UX Console” on
page 66 to correctly select your standard error device. Output on this
device will be important firmware messages reporting errors.
Step 5. Reset your system
A system reset is required for your console selections to take effect
Additional Notes on Console Selection
HP-UX makes decisions based upon the EFI Boot Maintenance Manager
menu's Select Active Consolesections to determine where to send its
output. If the incorrect console devices are chosen, HP-UX may either
fail to boot, or will boot with output directed to the wrong location.
Therefore, any time new potential console devices are added to a system,
or anytime NVRAM on a system is cleared, console selections should be
reviewed to ensure that they are correct.
More information on the EFI Paths used for console selection can be
found in Intel's Extensible Firmware Interface documents available from
their web site.
Chapter 4
69
Preparing to Migrate to HP-UX 11i v2
About Online Diagnostics
About Online Diagnostics
HP-UX 11i v2 automatically installs diagnostics on all systems to
provide required hardware support. These tools, contained in the
OnlineDiagbundle, give you a complete solution to verify, troubleshoot,
and monitor Itanium-based system hardware, including CPUs, memory,
interface cards, mass storage and other devices.
CAUTION
Uninstalling the OnlineDiag bundle prevents products with dependencies
on the diagnostics from functioning correctly.
Not installing OnlineDiagremoves protections against hardware
failures that diagnostics provide. Without the tools, it is much harder to
troubleshoot and fix problems if a hardware failure occurs.
To ensure the reliability of your computer system, we highly recommend
installing the OnlineDiagbundle with HP-UX 11i v2 (it will be installed
by default with any HP-UX 11i Operating Environment).
The tools in OnlineDiag:
•
Protect you against some hardware failures (for example, some
memory problems)
•
•
Notify you of hardware events that may indicate impending failure
Maintain logs that can give you critical help in determining the
cause of failures
•
Let you troubleshoot system problems with the system online
For most computer systems, no special configuration of the diagnostics is
necessary.
For complete information, see the diagnostics web site:
http://docs.hp.com/hpux/diag
70
Chapter 4
Preparing to Migrate to HP-UX 11i v2
About Online Diagnostics
About Offline Diagnostics
Offline Diagnostics (ODE) are on the HP Itanium-Processor Family
Offline Diagnostics and Utilities CD. The CD is delivered with the
hardware and is non-OS dependent (it is not delivered with the HP-UX
11i v2 media kit).
HP highly recommends that you get the latest CD and update the Offline
Diagnostics for improved functionality. To order the HP
Itanium-Processor Family Offline Diagnostics and Utilities CD, go to the
following web sites:
Software Depot: www.software.hp.com
Biz Support: www.hp.com/support/Itaniumservers
NOTE
For more information on ODE, go to the following web site:
http://www.docs.hp.com/hpux/onlinedocs/diag/ode/ode_over.htm
Chapter 4
71
Preparing to Migrate to HP-UX 11i v2
Backing Up Your System
Backing Up Your System
In addition to your normal, periodic system backup procedures, you
should create a network backup of your root volume group (see
Chapter 5, “Cold-Installing HP-UX 11i v2,” on page 79). Do this first
before performing a cold-install, and again after the cold-install. If a
problem occurs, it’s a very simple procedure to restore the system to its
original state.
This section offers several alternatives for performing system backups:
fbackup and frecover, and make_net_recovery and
make_tape_recovery.
Using fbackup and Many administrators use the basic fbackupcommand to back up the
frecover
entire system to tape. You do not need to unmount any imported file
systems; fbackupdoes not cross NFS boundaries unless specified.
Using the normal tape location to do a full backup, insert a new tape and
enter:
fbackup -f/dev/rmt/0m -i -v
Later, if you wish to return the system to its previous state, use the
frecovercommand. See the fbackup (1M) manpage for examples.
Ignite-UX recovery For recovering a system, a better alternative to using fbackupand
commands
frecoveris to use the make_net_recoveryor make_tape_recovery
commands available with Ignite-UX, which offer more flexibility than
systems.
The Ignite-UX server software for HP-UX 11i v2 is provided on the
HP-UX 11i v2 DVD, and can be cold-installed or updated along with
HP-UX 11i v2 to create or update a new server. See “Updating Your
Ignite-UX Server” on page 65 for details.
Using make_net_
recovery
The Ignite-UX server has the make_net_recoverycommand to create a
system recovery archive on another system on the network. The archive
created by make_net_recoveryis specific to the system it was created
for and its identity includes hostname, IP_address, networking
information, and so on. In the event of a root disk failure, you use the
Ignite-UX server to restore the system by installing the recovery archive.
72
Chapter 4
Preparing to Migrate to HP-UX 11i v2
Backing Up Your System
The contents of the system recovery archive always includes all files and
directories which are essential to bringing up a functional system. This
“essential” list is pre-defined by make_net_recovery. You can run
make_net_recoveryin its interactive mode to review the directories and
files which make up the “essential list,” and also add or remove other
data from the archive on a disk/volume group, file, or directory basis.
For more information on using make_net_recovery, see the
make_net_recovery (1M) manpage or the Ignite-UX Administration
Guide.
Using make_tape_ The Ignite-UX server’s make_tape_recoverycommand creates a
recovery
bootable recovery tape for an LVM or whole disk file system while it is up
and running. When a system has a logical volume layout, the recovery
tape will only include data from the root volume group, plus data from
any non-root volume group containing the /usr directory.
You can run make_tape_recoveryeither on the Ignite-UX server or
locally on the system from which you are trying to make a recovery tape.
To create the bootable recovery tape, enter:
/opt/ignite/bin/make_tape_recovery -Av
where: vis for verbose mode and A specifies the entire root disk or
volume group. Also, more than one volume group can be specified with
the -xoption.
If a tape drive other than the default (/dev/rmt/0m) will be used, modify
the command to point to the device you want to use, for example a tape
drive at /dev/rmt/3mn:
/opt/ignite/bin/make_tape_recovery -Av -d /dev/rmt/3mn
To recover a failed system disk or volume group after a recovery tape has
been made, simply load the recovery tape, boot the system, interrupting
the boot sequence to redirect to the tape drive. Allow the install process
to complete. Do not intervene. The system will reboot and, because map
files for all associated volume groups have been saved on the tape, any
other existing volume groups are imported and mounted automatically.
Data which is not in the root volume group must be backed up and
recovered using normal backup utilities.
Chapter 4
73
Preparing to Migrate to HP-UX 11i v2
Backing Up Your System
For more information on using make_tape_recovery, see the
make_tape_recovery (1M) manpage on an Ignite-UX server or the
Ignite-UX Administration Guide. The guide is available on the HP-UX
11i v2 Instant Information CD and at this web site:
http://docs.hp.com/
74
Chapter 4
Preparing to Migrate to HP-UX 11i v2
Saving Configuration Files
Saving Configuration Files
If you are planning to cold-install HP-UX 11i v2 on a system that already
has HP-UX installed, be sure to save the files that you will want to
re-install.
These include a number of configuration files in /etc, the contents of
/usr/local, any local home directories (that is, those you do not import
from another system), and any configuration files located in the
/etc/optdirectories for installed software.
If multiple users are preparing for the cold-install, you might consider
creating a directory (such as /backup) on another system. Do not create
this directory on your root disk. Mount it with sam. Then create a
subdirectory for each system or user (for example, /backup/your_sys).
As root, copy the files. For example:
Step 1. Copy all config files from /etcon a system named system1to system
system2. On system2, enter:
mkdir /backup/system1/etc
rcp -p your_name@system1:/etc/* /backup/system1/etc/.
Step 2. Copy your local home directory to the backup system:
mkdir /backup/system1/home
rcp -pr your_name@system1:/home/ /backup/system1/home/
Chapter 4
75
Preparing to Migrate to HP-UX 11i v2
Locating Source Media and Codewords
Locating Source Media and Codewords
Now that you have backed up your system and important data files, and
you have decided how to cold-install or update to HP-UX 11i v2, you need
to locate the source media needed for the migration:
•
If you are cold-installing or updating one system at a time —
cold-install or update directly from the DVDs in the HP-UX 11i v2
media kit:
— HP-UX 11i v2 DVD — Boot and install a new system.
— HP-UX Application DVDs — Install applications not installed
with the OE or install a newer version of an OE application.
Some applications installed with an HP-UX 11i v2 OE may be
older versions than those available on the HP-UX Applications
DVDs supplied in the media kit. Products available on
Application DVDs are listed in the TABLE_OF_CONTENTS file on
each DVD.
•
If you plan to cold-install on many systems in your enterprise
— We recommend using an Ignite-UX server to create a “golden
image” from which to cold-install. This install image can contain the
OS and OE, other applications, and any needed patches. Once the
archive is in place, either on the Ignite-UX server or on another
system, cold-install on each client system is a single-pass operation;
you will only need to reboot each client once.
For details on installing an Ignite-UX server, see the Ignite-UX
Administration Guide, supplied on the Instant Information DVD and
on this web site:
http://docs.hp.com/hpux/os/11iv2
76
Chapter 4
Preparing to Migrate to HP-UX 11i v2
Locating Source Media and Codewords
Locating Codewords
You can obtain a codeword for a purchased product by calling one of the
following numbers.
Table 4-1
HP Licensing Services
Location
Asia
Telephone
0120.42.1231
Email
(Inside Japan)
0426.48.9310
(Inside Japan)
+81.426.48.9312
(Outside Japan)
Europe
+33 (0)4.76.14.15.29
(800) 538-1733
North
America
NOTE
For more information on HP Licensing Services and codeword
redemption, go to the web:
http://licensing.hp.com
The Codeword Request forms also list the telephone numbers and web
site for codeword redemption.
Chapter 4
77
Preparing to Migrate to HP-UX 11i v2
The Next Steps
The Next Steps
•
•
•
•
•
•
“About Online Diagnostics” on page 70
“Backing Up Your System” on page 72
“Saving Configuration Files” on page 75
You are now ready to cold-install or update to HP-UX 11i v2
•
To cold-install: see Chapter 5, “Cold-Installing HP-UX 11i v2,” on
page 79
•
To update: see Chapter 6, “Updating to HP-UX 11i v2,” on page 93
78
Chapter 4
5
Cold-Installing HP-UX 11i v2
This chapter describes cold-installing HP-UX 11i v2.
•
•
•
•
•
“Before You Begin” on page 80
“Reviewing the Cold-Install Process” on page 81
“Cold-installing HP-UX 11i v2” on page 83
“Retrieving Information after Cold-installing” on page 90
“The Next Step” on page 92
To complete the steps in this chapter, we estimate you require 2-3 hours,
depending upon the system, and if you are installing the OS or an OE.
Please note that your time may vary.
CAUTION
The cold-install process overwrites everything on the root (/) disk. Make
sure you completed backups in “Backing Up Your System” on page 72.
Chapter 5
79
Cold-Installing HP-UX 11i v2
Before You Begin
Before You Begin
Before you cold-install HP-UX 11i v2, be sure you have done the
following:
•
You are installing from a supported migration path, see “Supported
Cold-Install Paths to HP-UX 11i v2” on page 33.
•
particularly:
•
•
•
and operate HP-UX 11i v2. For more details see Chapter 3,
“Installing and Updating System Requirements,” on page 51.
You have completed the preparation tasks required to update your
system. For more information see Chapter 4, “Preparing to Migrate
to HP-UX 11i v2,” on page 63.
See Appendix A, “Data Collection Tables,” on page 141 for
networking and other data that you need to collect.
80
Chapter 5
Cold-Installing HP-UX 11i v2
Reviewing the Cold-Install Process
Reviewing the Cold-Install Process
This section describes cold-installing from the HP-UX 11i v2 DVDs,
including the operating system, a selected operating environment (OE)
bundle, network drivers, CDE language bundle, and diagnostics.
The overall process is shown in Figure 5-1 on page 82, along with
alternate methods of cold-installing HP-UX 11i v2:
Alternate install
methods
•
•
Installing from software depots — Use Software Distributor
commands to create depots containing OS, OE, and other software
bundles, then install from the depot using Ignite-UX. For help with
this method, see the swinstall (1M) manpage, Software Distributor
Administration Guide, and Ignite-UX Administration Guide.
Installing from golden images — If you need to install the same
OS/OE and applications on many systems in your network, use an
Ignite-UX server as explained in the Ignite-UX Administration
Guide. With Ignite-UX, you can create a single install image (golden
image) containing OS/OE bundles, application bundles, and patch
bundles, then install the image on multiple systems in your
environment.
•
For customers ordering new systems with the “Instant Ignition”
option (also known as “factory ignited”), the cold-installation process
described here has already been performed. Skip this chapter and
proceed to Chapter 7, “Verifying System Install or Update,” on
page 117.
Mission Critical
Support
If your system is on HP Mission Critical Support, discuss the proper
method of installing and patching the OE with your HP Customer
Engineer.
Required media
Have these DVDs ready from the HP-UX 11i v2 media kit:
•
•
HP-UX 11i v2 DVD
HP-UX 11i v2 Applications DVD
Chapter 5
81
Cold-Installing HP-UX 11i v2
Reviewing the Cold-Install Process
Figure 5-1
Cold-installing HP-UX 11i v2
Determine
install
approach
If Factory
Integrated
FromGolden
From
From
Media
2
1
Image
Depots
Install 11i v2 OS/OE using
Ignite-UX
Create Install Golden
Create 2 install depots:
Image using
• OE depot: OS/OE
2
Ignite-UX Server
• AR depot: Applications
Install non-OE applications
using swinstall
Install image using
Ignite-UX Server
(see Chapter 8)
Install from OE depot using
Ignite-UX with config files
for both depots
Using tools from ITRC,
identify and install additional
Install non-OE applications
from AR depot using
swinstall
3
needed patches
Install 3rd-party and
internal software
1
For help creating depots, see the Software Distributor
Administration Guide
2
Golden image can contain OE/OE, patches, and application
Create
archive/recovery
image
bundles. For help creating golden images, see the Ignite-UX
Administration Guide
3
The Custom Patch Manager (CPM) can be found at the
ITRC (http://itrc.hp.com) and can be used to find additional
needed patches, such as patches for non-OE applications and
new security patches
Done
82
Chapter 5
Cold-Installing HP-UX 11i v2
Cold-installing HP-UX 11i v2
Cold-installing HP-UX 11i v2
To cold-install the operating system, use the following steps. Please note
that cold-installing overwrites everything on the target disk. You should
review the Appendix B, “Known Problems and Troubleshooting,” on
page 145 to see if any installation issues apply to your system.
Step 1. Make sure any external devices connected to the target system are
turned ON and operational.
Step 2. Insert the HP-UX 11i v2 DVD into the drive.
Step 3. Turn the system ON, reboot, or cycle power. The system should boot
automatically from the DVD.
•
•
If the system boots automatically, go to step 4.
If the system does not boot automatically, it goes to the boot menu. It
is a timed menu; press any key to stop the timer. Then, you can run
the install manually from the EFI shell using the following steps:
a. From the boot menu, select EFI Shell (Built In).
b. The list of devices displays automatically, and the install process
selects the device for you.
c. If the device is not automatically selected, select the device name for
the CDROM and then execute install. For example, from the EFI
shell prompt, you may see something similar to the following:
Shell> fs1:
fs1:\> install
If you do not see the CDROM device, use the mapcommand to list all
device names from the EFI shell prompt.
NOTE
Your DVD device may not always be fs1. Make sure you verify the
ID appropriate with your DVD device.
Step 4. Once the kernel has booted, it scans the system for I/O devices.
Chapter 5
83
Cold-Installing HP-UX 11i v2
Cold-installing HP-UX 11i v2
Continuing the Install with Ignite-UX Program
The system now displays the Ignite-UX welcome screen for the HP-UX
installation process. If you have used Ignite-UX on PA systems, the
remaining procedures will be familiar to you.
Step 1. Take a moment to read how to navigate and select choices on this
terminal interface:
•
•
•
•
Use the Tab key to navigate between fields and the arrow keys to
navigate within fields.
Use the Return/Enter key to select an item. Pressing Return/Enter or
the spacebar opens a menu list.
For Help, use Ctrl-K for navigation key help and Ctrl-F (or F1) for
context-sensitive help.
You can enter the underlined letter of an item (such as Ifor install
HP-UX) to navigate more quickly.
Step 2. If the install detects that you have a keyboard, pick the number of the
language you want to use, for example, 26. Confirm your choice.
*****************************************************
A USB interface has been detected on this system.
In order to use a keyboard on this interface, you must specify
a language mapping which will be used by X windows and
the Internal Terminal Emulator (ITE).
The characters “1234567890” will appear as “!@#$^&*()”
on keyboards that use the shift key to type a number.
Your choice will be stored in the file /etc/kbdlang
1) USB_PS2_DIN_Belgian
3) USB_PS2_DIN_Danish
5) USB_PS2_DIN_Euro_Spanish
7) USB_PS2_DIN_French
2)USB_PS2_DIN_Belgian_Euro
4)USB_PS2_DIN_Danish_Euro
6)USB_PS2_DIN_Euro_Spanish_Euro
8)USB_PS2_DIN_French_Euro
10)USB_PS2_DIN_German_Euro
12)USB_PS2_DIN_Italian_Euro
14)USB_PS2_DIN_Korean
16)USB_PS2_DIN_Norwegian_Euro
18)USB_PS2_DIN_Swedish
20)USB_PS2_DIN_Swiss_French2_Euro
9) USB_PS2_DIN_German
11) USB_PS2_DIN_Italian
13) USB_PS2_DIN_JIS_109
15) USB_PS2_DIN_Norwegian
17) USB_PS2_DIN_S_Chinese
19) USB_PS2_DIN_Swedish_Euro
21) USB_PS2_DIN_Swiss_German2 22)USB_PS2_DIN_Swiss_German2_Euro
23) USB_PS2_DIN_T_Chinese 24)USB_PS2_DIN_UK_English
25) USB_PS2_DIN_UK_English_Euro 26)USB_PS2_DIN_US_English
27) USB_PS2_DIN_US_English_Euro
Enter the number of the language you want: 26
84
Chapter 5
Cold-Installing HP-UX 11i v2
Cold-installing HP-UX 11i v2
You have selected the keyboard language USB_PS2_DIN_US_English.
Please confirm your choice by pressing RETURN or enter a new
number:
Step 3. Select Install HP-UX to begin interacting with the Ignite-UX (cold-install)
program.
Step 4. From the User Interface and Media Options screen, choose the degree of
customizing needed to configure the installation. The default setting
under Source Location Options (Media only installation) is correct for
installing from a DVD.
Three choices are shown in User Interface Options:
•
Guided Installation provides tutorial information and limited choices
for inexperienced Ignite-UX users.
•
Advanced Installation enables you to customize your system on tabbed
screens. Use this mode to change VxVM settings. You may also find
it convenient to set system parameters, network services, file-system
characteristics, and other configuration details.
•
No User Interface Use all the defaults and GO.
Ignite-UX permits you to exit from Guided Installation and restart the
configuration using Advanced Installation later by either selecting the
Cancel button or pressing C. Mark your choices and select OK.
Step 5. The remaining steps take you through the Guided Installation. For help,
consult the Help screens. For more help on using Advanced Installation,
see the Ignite-UX Administration Guide.
Deselecting OE Software Bundles
If you use the Guided or Advanced Installations, then you can deselect
the software bundles that are default installed. For a list of
default-installed software bundles, see “HP-UX 11i v2 Default-Installed
Software Bundles” on page 175.
If you choose the No User Interface option, then you cannot deselect the
default-installed software bundles.
Step 1. In the Guided or Advanced Installation screens, go to the Software tab.
Step 2. Use the arrow keys to select a bundle and the spacebar to change the
option.
Chapter 5
85
Cold-Installing HP-UX 11i v2
Cold-installing HP-UX 11i v2
IMPORTANT
Review the HP-UX 11i Version 2 Release Notes to ensure that any bundle
you deselect does not have a dependency. For example, you may deselect
a software bundle that is necessary for another program to work
correctly.
Continuing with Guided Installation
Step 1. You are now at the first step of the Install HP-UX Wizard: Select an
overall system configuration. Accept the default option: HP-UX B.11.23
Default.
Step 2. Select a system environment. In this step you will choose the type of
Operating Environment that will be installed on your system. Press
Return/Enter to view the choices.
For Technical Computing OE media, the choices are:
x Environments: [HP-UX 11i TCOE-64bit ->] (HP-UX B.11.23) x
x
x
HP-UX 11i MTOE-64bit
HP-UX 11i Base OS-64bit
x
x
For 11i v2 Foundation OE media, the choices are:
x Environments: [HP-UX 11i OE-64bit
HP-UX 11i Base OS-64bit
->] (HP-UX B.11.23) x
x
x
For Minimum Technical media, the choices are:
x Environments: [HP-UX 11i MTOE-64bit ->] (HP-UX B.11.23) x
x
HP-UX 11i Base OS-64bit
x
Step 3. Select a root disk. In this step you will choose the disk that will house
your root filesystem. If you are unsure of what to choose, keep the default
selection which has been calculated by the install program. Press
Return/Enter to view the choices.
Step 4. Specify the amount of root swap space. Some initial calculations have
been performed by the install program, and a recommended value has
been set for you. You can either accept this value or change it before
continuing. Press Return/Enter to view the choices.
86
Chapter 5
Cold-Installing HP-UX 11i v2
Cold-installing HP-UX 11i v2
Step 5. Select file system type. The default value chosen by the install program
is recommended. Press Return/Enter to view the choices.
x Install HP-UX wizard: Select a file system type
x
x Now that you have made your root swap selection, you
x
x
x
x need to choose which type of file system you would like x
x to use. The current choice displayed in the selector is x
x recommended. If you are unsure of what to choose, keep
x the default selection. You may then safely proceed to
x the next step.
x
x
x
x ----------------------------------------------------------x
x
x
x VERITAS Volume Manager (VxVM) with VxFS x
x Whole disk with VxFS
x
x File System: [x Logical Volume Manager (LVM) with VxFS] x
x-----------------------------------------------------------x
x
x
x
x
x
x
[ < Back ] [ Next > ] [ Cancel ] [ Help ]
x-----------------------------------------------------------x
NOTE
If you select VxVM, the root disk can not be moved to another SCSI bus
or address that results in a change in the hardware path to the device. If
it is moved, you may not be able to boot safely from it. This is similar to
the limitation present in LVM.
Step 6. Specify number of disks in the root group. In this step you will specify
how many disks you want placed into the root disk volume group and
whether or not you would like the disks to be striped. (The HP-UX Install
Wizard describes these features in depth.)
You must enter Yes or No to “Use Striping”.
Step 7. Select language(s). Browse the available languages, marking the desired
software which you would like loaded onto your system. Browse the list,
marking your selections, then continue to the next step.
For example, to secure your system at install-time with the Sec30DMZ
configuration bundle (see “Install-time Security Considerations” on
page 43):
Chapter 5
87
Cold-Installing HP-UX 11i v2
Cold-installing HP-UX 11i v2
a. Select SecurityChoices. The four security configuration bundles
appear. By default, Sec00Toolsis selected.
b. Select Sec30DMZfrom the list.
c. Select OK.
Step 9. Pre-Install disk information, Step 1. There are two steps involved in the
pre-install checks. The first is to identify which disks will be overwritten
during the install process. If you see a disk in the list that you do not
want included, back up to the root disk selection and choose another
disk. Otherwise, continue on to the next step.
Step 10. Pre-Install check information, Step 2. The second step in the pre-install
check is to review any errors, warnings, or notes. Warnings are simply
informational. If there are any errors, they will need to be resolved
before the installation can continue.
Step 11. System summary. At this point you have successfully defined your
system. Use the Show Summary button to view a summary of how your
system will be configured. If you see any problems, or wish to change any
of your selections, feel free to back up to the appropriate step, and make
the needed changes. Otherwise, select Finish (at the bottom of the tabs).
You have the chance to Cancel at this time. If you cancel, you can start
again.
Step 12. Next, the installation will begin with filesets being copied from the
media to the hard disk. The system will automatically reboot during the
installation process.
Step 13. Depending on how you set up your parameters, the system will either set
basic network configurations automatically, or will call the set_parms
command after it has rebooted to allow you to set the root password, date
and time, time zone, IP address, and additional network parameters.
After set_parmsis executed, then the “Welcome to HP-UX” screen will
be displayed.
Step 14. In order to use a keyboard on this interface, you must specify a language
mapping which will be used by X Windows and the Internal Terminal
Emulator (ITE). Choose the appropriate language. For English, select
number 26.
88
Chapter 5
Cold-Installing HP-UX 11i v2
Cold-installing HP-UX 11i v2
the system. The first is whether or not you plan to use the system on a
network. If you completed the pre-install data collection tables in
Appendix A, “Data Collection Tables,” on page 141, you have all the
information you need for set_parms, so answer Y for yes.
Step 16. Enter the basic network information that you collected in Appendix A,
“Data Collection Tables,” on page 141 on the screens that follow.
Step 17. Confirm your choices. Congratulations! You are now finished with the
install procedure and will be given the opportunity to log in to the system
as root.
Step 18. Log in to the system.
Step 19. After the cold-install, store the HP-UX DVDs in a safe place. You may
need them to install drivers or other software later.
Chapter 5
89
Cold-Installing HP-UX 11i v2
Retrieving Information after Cold-installing
Retrieving Information after Cold-installing
After completing the cold-install, you can retrieve the information you
had previously saved onto another system. Here are some tips:
Creating a new
root home
directory
Consider creating a root home directory that is not /. This keeps the user
root dot files out of the / directory. Make sure it is on the root volume by
calling it something like /homeroot. This is especially important if you
are using LVM and /homeis a separate volume.
Step 1. From the CDE login screen, select Options -> Command Line Login and
login as root.
Step 2. Except on trusted systems, edit /etc/passwdto change the home
directory from root to /homerootand save it.
Step 3. Create the /homerootdirectory:
mkdir /homeroot
Step 4. Move root’s personal files (files beginning with .) to /homeroot:
mv /.[a-zA-Z]* /homeroot
Step 5. Exit and log in again as root.
Recovering files
Recover all the customized and personal files that you saved previously
by merging them manually. For example, do not overwrite /etc/passwd
with your old version. Instead, either paste in entries from your old files
or merge the old information into the new files.
Restoring /home
If you had a local home directory, you can restore it as follows:
•
For instance, if you copied it to, /backup/system1/home, enter these
commands:
cd /backup/system1/home
find -depth | cpio -pdm /system1/home
•
If you backed it up to tape with fbackup, enter:
frecover -x -i /system1/home -v
90
Chapter 5
Cold-Installing HP-UX 11i v2
Retrieving Information after Cold-installing
Restoring other
files
Carefully use the same techniques to restore other files and directories,
such as /usr, /local and /opt. For help in importing entire volume
groups, see either the Managing Systems and Workgroups: A Guide for
HP-UX System Administrators or the Managing Superdome Complexes.
The commands above will not write over newer files, so your new
operating system and any files you update are well protected.
Chapter 5
91
Cold-Installing HP-UX 11i v2
The Next Step
The Next Step
You have completed the cold-install process:
•
•
•
“Reviewing the Cold-Install Process” on page 81
“Retrieving Information after Cold-installing” on page 90
Continue with chapter:
Chapter 7, “Verifying System Install or Update,” on page 117
•
92
Chapter 5
6
Updating to HP-UX 11i v2
cold-install, see Chapter 2, “Choosing a Migration Path,” on page 31.
•
•
•
•
•
•
•
“Before You Begin” on page 94
“Updating Tips” on page 97
“Updating to HP-UX 11i v2” on page 99
“Configuring OE Applications” on page 108
“Creating an HP Service Partition” on page 109
“The Next Step” on page 115
To complete the steps in this chapter, we estimate you require 3-4 hours,
depending upon the system, and if you are updating the OS or an OE. If
you need to create an HP Service Partition, you will need an additional
4-6 hours. Please note that your time may vary.
Chapter 6
93
Updating to HP-UX 11i v2
Before You Begin
Before You Begin
Before you update to HP-UX 11i v2, be sure you have done the following:
✓ You are updating from a supported migration path, see “Supported
Update Paths to HP-UX 11i v2” on page 34
particularly:
— “Update Considerations” on page 40
and operate HP-UX 11i v2. For more details see Chapter 3,
“Installing and Updating System Requirements,” on page 51
✓ You have completed the preparation tasks required to update your
system. For more information see Chapter 4, “Preparing to Migrate
to HP-UX 11i v2,” on page 63.
94
Chapter 6
Updating to HP-UX 11i v2
Reviewing the Update Process
Reviewing the Update Process
This section describes updating to HP-UX 11i v2 using update-ux
command and Software Distributor (SD) tools to selectively overwrite
the operating system and application software from a media or network
source depot.
The overall process is described in Figure 6-1 on page 96, along with
alternate methods of updating to HP-UX 11i v2:
IMPORTANT
You must install the latest version of Update-UX prior to updating your
system. Failure to do so may cause the update to fail.
Alternate Update
Methods
•
•
Updating from network depots
Updating from DVD media
Mission Critical
Support
If your system is on HP Mission Critical Support, discuss the proper
method to update and patch your operating environment with your HP
Customer engineer.
Chapter 6
95
Updating to HP-UX 11i v2
Reviewing the Update Process
Figure 6-1
Updating to HP-UX 11i v2
Create
archive/recovery
image
update
depots
Important!
Install latest
update-ux
Determine
update
approach
Create depots(s)
Determine
source
media
You can still
opt to
cold-install
Update HP-UX 11i v2
from depot containing
OS/OE bundles using
update-ux
Continue to update
OS/OE from 11i v2 OE
media using update-ux
Cold-Install from
media, depots or
golden image
Update non-OE
applications from
Application media
using swinstall
Update non-OE
applications using
swinstall
Identify and install
non-OE patches (use
Custom Patch
Manager)
Install 3rd-party and
internal software
Create HP Service
Partition using
make_*_recovery
tools
Have HP
Service
Partition?
Create
archive/recovery
image
NO
YES
DONE
96
Chapter 6
Updating to HP-UX 11i v2
Updating Tips
Updating Tips
During an update process, here are some tips and recommendations:
Monitoring the Update Process
If you wish to view the update process in detail, open another terminal
window (drag it aside so you can also watch for any messages on the
window running update-ux) and use the tailcommand to view
swinstallmessages being logged:
tail -f /var/adm/sw/swagent.log
You may also wish to log all messages directed to the console by using
the scriptcommand. For example, to log all messages into a file named:
/tmp/updateOS, enter:
script -a /tmp/updateOS
To halt the scriptlog process, enter: exit
Running Other Commands
You can run other commands during an update, such as viewing files and
an update; doing so may cause the commands to function improperly.
In Case of Trouble
If you encounter a problem during the update process, review
Appendix B, “Known Problems and Troubleshooting,” on page 145 for
possible solutions.
The update-uxcommand returns an error value when it is not
successful:
1 - Error during execution; update aborted.
2 - Update aborted via user action (-n or keyboard press)
Messages are recorded in /var/adm/sw/swagent.log,
/var/adm/sw/swinstall.log, and /var/adm/sw/update-ux.log.
When updating Ignite-UX, also look at its log in /var/adm/sw/.
Chapter 6
97
Updating to HP-UX 11i v2
Updating Tips
All Software Does Not Get Updated
The update-uxcommand updates the HP-UX OS and any software
specified in additional software bundles available on the source media or
depot. When an OE is specified, some products in the OE will not get
with an OE already exists on the system.
You will have to update or re-install those products after updating
HP-UX 11i v2. For more information about how to update these
additional software bundles, please see “Updating Selectable Software”
on page 106.
98
Chapter 6
Updating to HP-UX 11i v2
Updating to HP-UX 11i v2
Updating to HP-UX 11i v2
After determining if your system meets the requirements for updating to
HP-UX 11i v2 and preparing your system, you are ready to update your
system. Updating your system using update-uxincludes the following
steps:
•
how to create a network depot to update other systems on the
procedure.
•
•
“Step 1: Installing the update-ux Command (Required Task)” on
page 100: Shows you how to install the update-uxcommand on your
system.
“Step 2: Using update-ux to Update to HP-UX 11i v2” on page 101:
Shows you how to use update-uxto update your system. Several
examples are provided to assist you with some of the most common
scenarios for using update-ux.
Optional Step: Creating a Network Depot
NOTE
This optional step pertains to creating a network depot to be used to
update other systems on the network.
If you are attempting to update your system from a network depot, start
with “Step 1: Installing the update-ux Command (Required Task)” on
page 100.
As root, follow this procedure to create a network depot from the HP-UX
11i v2 DVD onto a depot server or other system running HP-UX 11i v2 in
your network:
Step 1. Verify that you have at least 2,000 MB (2 GB) of free space to create the
network depot on another system in your network. If this space is not
available, use samto either create a new volume group or extend an
existing volume group. For help, see either SAM help or the Managing
Systems and Workgroups manual.
Chapter 6
99
Updating to HP-UX 11i v2
Updating to HP-UX 11i v2
Step 2. Log in as root and mount the logical volume on a new directory named
/update. This directory will hold your network depot.
Step 3. Insert the HP-UX 11i v2 DVD and wait for the drive’s busy light to stop
blinking.
Step 4. Find the DVD-ROM device file name:
ioscan -f -C disk | more
/dev/dsk/c1t2d0is a typical device name.
Step 5. Create the directory under root(/):
mkdir /dvdrom
Step 6. Mount the DVD onto the new directory as a file system. For example:
mount /dev/dsk/c1t2d0 /dvdrom
Step 7. Copy all products on the mounted DVD to the target depot, for example
/update/update-depot:
swcopy -s /dvdrom \* @ /update/update-depot
Step 8. Unmount the DVD from its directory
umount /dvdrom
The network depot is now ready to update your system to HP-UX 11i v2.
Continue with Step 1: Installing the update-ux Command (Required
Task)
Step 1: Installing the update-uxCommand (Required
Task)
IMPORTANT
Prior to updating your system, you must install the latest version of the
update-uxcommand.
Step 1. Insert the HP-UX 11i v2 DVD and wait for the drive’s busy light to stop
blinking.
100
Chapter 6
Updating to HP-UX 11i v2
Updating to HP-UX 11i v2
Step 2. Find the DVD-ROM device file name:
ioscan -f -C disk | more
/dev/dsk/c1t2d0is a typical device name.
Step 3. Create the directory under root(/):
mkdir /dvdrom
Step 4. Mount the DVD onto the new directory as a file system. For example:
mount /dev/dsk/c1t2d0 /dvdrom
Step 5. Using either ksh, Posix-sh or Bourne shell, install update-uxon the
target system.
From the DVD
swinstall -s /dvdrom Update-UX
media
From a depot
The depot example uses the following syntax:
depot_server:<depot_path>.
swinstall -s depot_server:/var/depots/my_depot Update-UX
Step 2: Using update-uxto Update to HP-UX 11i v2
After you have installed update-uxon the target system (see “Step 1:
Installing the update-ux Command (Required Task)” on page 100) and,
optionally, created an update depot containing all software to be
installed, (see “Optional Step: Creating a Network Depot” on page 99),
you can now proceed to update your target system. Use the following
syntax to run update-ux:.
Chapter 6
101
Updating to HP-UX 11i v2
Updating to HP-UX 11i v2
update-ux Syntax
update-ux -s source_location [-?] [-n|-y] [-i]
[-x option=value] [sw_spec]
where:
-s source_location
Specifies the source containing the new software depot.
Possible locations are a local directory, a mounted DVD
containing a depot, or a remote system-and-depot
combination. All paths used in the source_location
must be absolute paths. If source_locationis a
remote system/depot combination, the remote system
should be specified first, followed by the absolute path
to the remote depot, separated by a colon with no
spaces; for example: swperf:/var/spool/sw
-?
Prints the usage statement.
-n|-y
update-uxissues a message and waits for your
response to continue whenever something unexpected
is attempted. Specify -nat first (or omit this option) to
have update-ux“not continue” when an error is issued.
When you have reviewed/resolved all errors, use -y
instead of -nto have update-uxignore all messages
which would otherwise cause update-uxto wait for a
user response.
-i
Specifies the swinstallinteractive user interface to
select software products from a depot or bundle during
the update. For more information, see the swinstall
(1M) manpage.
-xoption=value
Specifies swinstalloptions to be applied during the
update. For a typical update, no swinstalloptions are
required. swinstall -p(preview) is not supported. For
information on swinstalloptions, see the swinstall
(1M) manpage or the Software Distributor
Administration Guide.
sw_spec
Specifies one or more optional software bundles to be
updated, such as an operating environment (OE)
bundle name, a network-driver bundle or Ignite-UX. If
102
Chapter 6
Updating to HP-UX 11i v2
an OE bundle name is not included on the command
line, only the core OS will be updated. For more
information, see Appendix D, “Software Distribution
Media,” on page 161.
For more about update-ux, see the update-ux (1M) manpage.
update-ux Examples
use update-ux. In this section, we provide some scenarios and examples
of how you might use update-uxto update your system:
•
how to update to HP-UX 11i v2 with an operating environment.
•
Updating to HP-UX 11i v2 OS (No OE Installed) on page 105 shows
environment.
•
your system by either adding or upgrading the operating
environment on your system.
•
•
update your system from a server on the network.
Updating Using Interactive Software Selection on page 106 shows
you how to use the interactive option to manually select the software
you want to update.
•
Updating Selectable Software on page 106 shows you how to update
your system with selectable software bundles.
Chapter 6
103
Updating to HP-UX 11i v2
Updating to HP-UX 11i v2
We Recommend
this Update:
Updating to HP-UX 11i v2 OS (OE Installed)
To update to HP-UX 11i v2 and include an HP-UX 11i v2 operating
environment, you need to specify the OE bundle name in the update-ux
command. The OE bundles names are:
HPUX11i-OE
HP-UX 11i v2 Foundation OE
HPUX11i-OE-EntHP-UX 11i v2 Enterprise OE
HPUX11i-OE-MC HP-UX 11i v2 Mission Critical OE
HPUX11i-MTOE HP-UX 11i v2 Minimal Technical OE
HPUX11i-TCOE HP-UX 11i v2 Technical Computing OE
For example, to update to HP-UX 11i v2 and install HP-UX 11i v2
Foundation OE, insert the HP-UX 11i v2 DVD in the local drive mounted
at /dvdrom. As root, enter:
/usr/sbin/update-ux -s /dvdrom HPUX11i-OE
Enterprise OE (from a supported update path), you would enter:
/usr/sbin/update-ux -s /dvdrom HPUX11i-OE-Ent
NOTE
NOTE
Please be sure to read See “Supported Update Paths to HP-UX 11i v2” on
page 34 to ensure that you are updating your system from a supported
update path.
want (such as Ignite-UX, HP-UX IPFilter, and the selectable network
drivers) at the same time that you do your update. See “Updating
Selectable Software” on page 106 for more information.
For details on what is included in each of the Operating Environments,
see Appendix D, “Software Distribution Media,” on page 161.
104
Chapter 6
Updating to HP-UX 11i v2
Updating to HP-UX 11i v2
Updating to HP-UX 11i v2 OS (No OE Installed)
NOTE
environment to provide you with an integrated and tested set of
supporting software and applications.
If you do not specify an OE bundle update-uxwill only install the OS,
networking, diagnostic and CDE bundles listed on page 161. Any
additional software bundles associated with an OE are not installed.
For example, to update the HP-UX 11i v2 OS, insert the HP-UX 11i v2
DVD in the local mounted drive and enter the following command:
/usr/sbin/update-ux -s /dvdrom
Adding or Upgrading an OE
To install an OE on an HP-UX 11i v2 system not containing an OE, or to
upgrade HP-UX 11i v2 to higher-level OE (for example, HP-UX 11i v2
Foundation OE to HP-UX 11i v2 Enterprise OE) insert the HP-UX 11i v2
DVD and specify the new OE using the update-uxcommand. For
example, to add the HP-UX 11i v2 Enterprise OE, enter:
/usr/sbin/update-ux -s /dvdrom HPUX11i-OE-Ent
When the update is complete, the original OE bundle wrapper (if one
existed) will be removed and replaced with the new bundle wrapper.
IMPORTANT
Upgrading to a higher level OE is only supported if you are updating
from a lower level HP-UX 11i v2 operating environment. In other words
you cannot update, for example, from HP-UX 11i v1.6 Foundation OE to
HP-UX 11i v2 Enterprise OE
You can not downgrade from a higher level OE to a lower level OE
Updating From a Network Depot
To update from an network depot on a remote system named netdepot,
include the path to the depot in the update-uxcommand. The following
example does an update to the HP-UX 11i v2 Enterprise OE:
Chapter 6
105
Updating to HP-UX 11i v2
Updating to HP-UX 11i v2
/usr/sbin/update-ux -s netdepot:/update/update_depot \
HPUX11i-OE-Ent
Updating Using Interactive Software Selection
To interactively select software for an update, use the -ioption. For
example:
/usr/sbin/update-ux -s /cdrom -i
update-uxdisplays swinstall’s interactive user interface with software
already selected to match the default update. Now you can change
software selections. For example, you can select a non-default network
driver or a web browser before performing the update. Since update-ux
selects OS, networking, language, and diagnostic bundles by default, the
interactive user interface provides a way to deselect the default software.
CAUTION
Do not combine -iand -xoptions in the same update-uxcommand.
IMPORTANT
swinstall’s interactive user interface does not provide for selecting
mutually exclusive selectable software bundles. As a result, if you select
more than one HP-UX Bastille security configuration bundle from the
SecurityChoices section of the Select Additional Software screen (for
example, Sec20MngDMZand Sec30DMZ), HP-UX Bastille will apply the
highest security configuration selected.
For help using swinstallin interactive mode, see the swinstall (1M)
Updating Selectable Software
To update to HP-UX 11i v2 and include additional selectable software
such as one of the HP-UX Bastille Security Configuration bundles, like
Sec30DMZ(see “Install-time Security Considerations” on page 43):
Step 1. Assuming you are updating from the DVD media, as root, enter:
/usr/sbin/update-ux -x /dvdrom HPUX11-OE Sec30DMZ
106
Chapter 6
Updating to HP-UX 11i v2
Updating to HP-UX 11i v2
In the above command, update-uxinstalls the HP-UX 11i v2 Foundation
Operating Environment bundles listed on Appendix D, “Software
Distribution Media,” on page 161, plus the Sec30DMZsecurity
configuration bundle (including HP-UX Bastille, Perl, HP-UX IPFilter -
included in Sec00Tools).
If you only want to update your system with a selectable software
bundle, enter:
/usr/sbin/update-ux -s /dvdrom Sec30DMZ
NOTE
If you select more than one HP-UX Bastille security configuration
bundle, for example Sec20MngDMZand Sec30DMZ, the highest level of
security will be applied to your system.
IMPORTANT
HP-UX Bastille’s security model is such that it provides incrementally
higher security (metaphorically, like a ratchet). As a result, you can
update from a lower security level to a higher security level (example:
Sec10Hostto Sec20MngDMZ.
If you intend to downgrade from a higher security level to a lower
security level, HP recommends that you run bastille -rbefore you
update your system to ensure that only the security settings you wanted
in the lower security level are applied. Otherwise, you may encounter
some security configurations left over from the previous security settings
applied by HP-UX Bastille.
Step 2. Complete any configuration for HP software explained in the HP-UX 11i
v2 Release Notes available on the Instant Information DVD and on
http://docs.hp.com/hpux/os/11iv2. In this example, to complete the
HP-UX Bastille installation, see the security chapter in the Managing
Systems and Workgroups manual.
Chapter 6
107
Updating to HP-UX 11i v2
Configuring OE Applications
Configuring OE Applications
After updating to an HP-UX 11i v2 operating environment (OE), some
OE products will need post-installation configuration to make them
functional. This may be indicated by a message logged in
/var/adm/sw/swagent.log.
Refer to each product’s installation instructions for details. The location
of OE product documentation is listed in the HP-UX 11i v2 Release Notes
(available on the Instant Information DVD and http://docs.hp.com).
108
Chapter 6
Updating to HP-UX 11i v2
Creating an HP Service Partition
Creating an HP Service Partition
Update-UX does not create or modify the HP Service Partition required
by some HP Offline Diagnostics tools. If you are updating from a system
that does not have an HP Service Partition, such as system newly
updated from HP-UX 11i v1.6, you will need to create the HP Service
Partition now.
To Determine If the HP Service Partition Exists
Step 1. As root, find the location of your root disk:
•
If you are using LVM, enter the following command:
lvlnboot -v
You should see results similar to the following:
# lvlnboot -v
Boot Definitions for Volume Group /dev/vg00:
Physical Volumes belonging in Root Volume Group:
/dev/dsk/c2t1d0s2 (0/1/1/0.1.0) -- Boot Disk
Boot: lvol1
Root: lvol3
Swap: lvol2
Dump: lvol2
on:
on:
on:
on:
/dev/dsk/c2t1d0s2
/dev/dsk/c2t1d0s2
/dev/dsk/c2t1d0s2
/dev/dsk/c2t1d0s2, 0
•
For VxVM, enter the following command:
vxprint -d
You should see output similar to the following:
# vxprint -d
Disk group: rootdg
TY NAME
ASSOC
KSTATE LENGTH PLOFFS STATE
TUTIL0 PUTIL0
dm rootdisk01 c0t0d0s2
-
34640800 -
-
-
-
Chapter 6
109
Updating to HP-UX 11i v2
Creating an HP Service Partition
Step 2. Run the idiskcommand on the boot disk. For example on LVM enter:
# idisk -p /dev/rdsk/c2t1d0
Figure 6-2 shows idiskoutput without an HP Service Partition
installed;Figure 6-3 shows idiskoutput showing an HP Service
Partition installed.
Figure 6-2
idiskOutput Showing No HP Service Partition Installed
idisk version: 1.31
EFI Primary Header:
Signature
= EFI PART
Revision
= 0x10000
HeaderSize
= 0x5c
HeaderCRC32
= 0x20e10a24
MyLbaLo
= 0x1
AlternateLbaLo
FirstUsableLbaLo
LastUsableLbaLo
Disk GUID
= 0x43d671f
= 0x22
= 0x43d66fc
= 59609df4-c295-11d7-8001-d6217b60e588
= 0x2
PartitionEntryLbaLo
NumberOfPartitionEntries = 0xc
SizeOfPartitionEntry
= 0x80
PartitionEntryArrayCRC32 = 0xc0a93cc2
Primary Partition Table (in 512 byte blocks):
Partition 1 (EFI):
Partition Type GUID
Unique Partition GUID
Starting Lba
= c12a7328-f81f-11d2-ba4b-00a0c93ec93b
= 5960a1be-c295-11d7-8002-d6217b60e588
= 0x22
Ending Lba
= 0xfa021
Partition 2 (HP-UX):
Partition Type GUID
Unique Partition GUID
Starting Lba
= 75894c1e-3aeb-11d3-b7c1-7b03a0000000
= 5960a1fa-c295-11d7-8003-d6217b60e588
= 0xfa022
Ending Lba
= 0x430e021
110
Chapter 6
Updating to HP-UX 11i v2
Creating an HP Service Partition
Figure 6-3
idiskOutput Showing HP Service Partition Installed
idisk version: 1.31
EFI Primary Header:
Signature
= EFI PART
= 0x10000
= 0x5c
Revision
HeaderSize
HeaderCRC32
= 0x20e10a24
= 0x1
MyLbaLo
AlternateLbaLo
FirstUsableLbaLo
LastUsableLbaLo
Disk GUID
= 0x43d671f
= 0x22
= 0x43d66fc
= 59609df4-c295-11d7-8001-d6217b60e588
= 0x2
PartitionEntryLbaLo
NumberOfPartitionEntries = 0xc
SizeOfPartitionEntry
= 0x80
PartitionEntryArrayCRC32 = 0xc0a93cc2
Primary Partition Table (in 512 byte blocks):
Partition 1 (EFI):
Partition Type GUID
Unique Partition GUID
Starting Lba
= c12a7328-f81f-11d2-ba4b-00a0c93ec93b
= 5960a1be-c295-11d7-8002-d6217b60e588
= 0x22
Ending Lba
= 0xfa021
Partition 2 (HP-UX):
Partition Type GUID
Unique Partition GUID
Starting Lba
= 75894c1e-3aeb-11d3-b7c1-7b03a0000000
= 5960a1fa-c295-11d7-8003-d6217b60e588
= 0xfa022
Ending Lba
= 0x430e021
Partition 3 (HPSP):
Partition Type GUID
Unique Partition GUID
Starting Lba
= e2a1e728-32e3-11d6-a682-7b03a0000000
= 5960a22c-c295-11d7-8004-d6217b60e588
= 0x430e022
Ending Lba
= 0x43d6021
Chapter 6
111
Updating to HP-UX 11i v2
Creating an HP Service Partition
Partition were already configured, you should see a third partition listed
as HPSP.
If you already have an HP Service Partition (your output looks similar to
Figure 6-3), you may skip the rest of this section and continue with, “The
Next Step” on page 115.
Before You Begin You will need to ensure that you have a minimum of 1 GB of disk space
that you can allocate for use by the EFI Boot Disk Partition and the new
HP Service Partition prior to beginning this procedure.
Make sure that you are familiar with the Ignite-UX make_tape_recovery
(1M) or make_net_recovery (4) commands before you start. You can also
find more information about Ignite-UX, including the latest
documentation, on the web:
http://software.hp.com/products/IUX
The following procedure will take you through creating and configuring a
new HP Service Partition.
Creating an HP Service Partition
Step 1. Determine which recovery method to use:
• make_tape_recoverygenerally provides faster recovery/restore
performance than make_net_recovery. However HP Integrity
servers do not support direct boot from tape devices. Consequently,
you will need to perform a “two-step media” recovery process. This
means that you will need a tape device with enough capacity to hold
the system archive, the HP-UX 11i v2 DVD media along with the
recovery tape to create the HP Service Partition and restore your
system.
• make_net_recoveryrecovery/restore performance is determined by
the speed of your network. In most cases, this method is slower than
make_tape_recovery. However, you can boot directly to the
Ignite-UX server containing your system archive.
112
Chapter 6
Updating to HP-UX 11i v2
Creating an HP Service Partition
IMPORTANT
The recovery process may fail if the boot disk file system is very full
while attempting to create a full archive with make_tape_recoveryor
make_net_recovery, causing either the system or user data restore to
run out of space.
HP strongly recommends that you back up your user data using other
supported backup software for HP-UX 11i v2, and use
make_tape_recoveryor make_net_recoveryto create an archive of
your system data.
See the Ignite-UX Administration Guide for more details on the
make_net_recoveryand make_tape_recoverycommands.
Step 2. Make a system archive using either the make_net_recoveryor
make_tape_recoverycommand:
•
To save a system archive to an Ignite-UX server:
make_net_recovery -s iuxServer -x inc_entire=vg00
To save a system archive to tape:
•
make_tape_recovery -a /dev/rmt/0mn -x inc_entire=vg00
Step 3. Reboot your system. If you created a system archive using the
make_tape_recoverycommand, insert your HP-UX 11i v2 DVD into the
DVD drive, before resetting your system.
Step 4. Depending on which method you used to create your system archive,
choose the appropriate boot method:
• make_net_recoverymethod: Select the appropriate network EFI
boot option
• make_tape_recoverymethod: Select the appropriate DVD boot
option
NOTE
See the “System Recovery” chapter of the Ignite-UX Administration
Guide for more details and information about the appropriate boot
methods.
Chapter 6
113
Updating to HP-UX 11i v2
Creating an HP Service Partition
Step 5. Enter the appropriate Keyboard device for your system.
Step 6. The Welcome to Ignite-UX! screen appears. Using the Tab key, select
Advanced Options. The User Interface and Media Options screen appears.
Step 7. From the list of User Interface Options, select Advanced Installation, then
select OK. The /opt/ignite/bin/itool() screen appears.
Step 8. From the Basic tab, select Additional.... The Additional Configuration
Controls screen appears. This screen includes a list of current partitions
and their sizes (in KB).
Step 9. Select EFI Boot Partition. A popup screen appears listing partition size
options (in KB) that you can choose from. Select 512000(500 MB) from
the list and select OK. You should now be back in the Additional
Configuration Controls screen.
Step 10. Select HP Service Partition. Select 409600(400 MB) from the list and
select OK.
Step 11. In the Additional Configuration Controls screen, select OK.
Step 12. In the /opt/ignite/bin/itool() screen select Go! Your system partitions (EFI
and HP Service Partition) have been configured and Ignite-UX will now
begin restoring your system data.
Step 13. If you backed up your user data using other backup software, restore this
data now following the vendor’s restore procedures.
Step 14. After your system and user data has been restored, run the idisk
command again to verify that the HP Service Partition was created and
the partition size is correct.
114
Chapter 6
Updating to HP-UX 11i v2
The Next Step
The Next Step
•
•
•
•
•
•
“Before You Begin” on page 94
“Updating Tips” on page 97
“Updating to HP-UX 11i v2” on page 99
“Creating an HP Service Partition” on page 109
Continue with the next chapter:
•
Chapter 7, “Verifying System Install or Update,” on page 117
Chapter 6
115
Updating to HP-UX 11i v2
The Next Step
116
Chapter 6
7
Verifying System Install or
Update
either installing or updating to HP-UX 11i v2.
What You Will Find in This Chapter
•
•
•
“Verifying the HP-UX Install or Update” on page 118
“Verifying HP-UX Applications” on page 120
“Changing the State of HP-UX Installed Patches” on page 121
To complete the steps in this chapter, we estimate you require 2-3 hours
to verify the HP-UX install or update, applications, and patches. Please
note your time may vary.
TIP
This chapter provides verification information for the HP-UX install,
update, applications, and patches. To check other software patches and
applications, please refer to the appropriate vendor documentation.
Chapter 7
117
Verifying System Install or Update
Verifying the HP-UX Install or Update
Verifying the HP-UX Install or Update
To verify that HP-UX 11i v2 was installed or updated successfully, use
the Software Distributor commands swlistand swverify.
Start Task
1. Run swlistto determine all software installed on your system:
/usr/sbin/swlist
You can control the detail level of the information displayed with the
-loption. To see all bundles installed, use this command:
/usr/sbin/swlist -l bundle
To see all products installed or all filesets installed, use these
commands:
/usr/sbin/swlist -l product
/usr/sbin/swlist -l fileset
For a cold-install, compare your list with the list of software products
in the TABLE_OF_CONTENTSfiles on the HP-UX 11i v2 Operating
System DVD and on the Applications DVD.
2. Run swverifyto verify that each bundle is intact. Several examples
follow:
•
To verify that an installed English 64-bit OS is intact, enter the
command:
/usr/sbin/swverify HPUXBaseOS
•
To verify all HP software on your system, enter the command:
/usr/sbin/swverify \*
The Selection process determines all dependencies of all software.
After the list, the following message displays:
* Selection succeeded.
Then, the Analysis process verifies that each required file is loaded
(existence and revision), that all required dependencies are met, and
then it runs any available verification scripts for the product. After
the analysis, the following message displays:
* Analysis succeeded.
118
Chapter 7
Verifying System Install or Update
Verifying the HP-UX Install or Update
If the analysis fails, either view /var/adm/sw/swagent.logto
review the analysis log or run the swjob... command listed at the end
of the swverifyreport sent to standard output.
* Verification succeeded.
TIP
For help with these commands, see the swlist (1M) and swverify (1M)
manpages, and the Software Distributor Administration Guide, which is
available on the Instant Information CD or the web:
http://docs.hp.com/hpux/os/11iv2
NOTE
The HP-UX Bastille install-time security configuration bundles
(Sec10Host, Sec20MngDMZ, or Sec30DMZ) will not appear in the
swagent.log. Instead, review your rc.logto determine the status of the
install-time security configuration. If errors are found in the rc.log,
review /var/opt/sec_mgmt/bastille/level-application-errorsfor
more details.
Chapter 7
119
Verifying System Install or Update
Verifying HP-UX Applications
Verifying HP-UX Applications
To verify that all required HP-UX applications have been installed or
updated, you should have already tried the Software Distributor
commands swlistand swverify, as explained in “Verifying the HP-UX
Install or Update” on page 118.
For example, to verify that the HP-UX 11i v2 default operating
environment is intact on your system, enter the command:
/usr/sbin/swlist -l bundle
Identify the bundle(s) containing the OE extension.
Then enter this command to verify it:
/usr/sbin/swverify bundle-name
If you get an error like the following, then the software identified is
incompatible with your system and needs to be replaced with a newer
version:
system's architecture or operating system.
Start Task
To update the HP-UX software, do the following:
1. Mount the HP-UX Applications DVD that contains the software.
2. Go to Chapter 8, “Installing Patches and Applications,” on page 125
to install or update the new version using the swinstallcommand.
3. Use the application; this is the best way to verify the application’s
operation.
Open each application, view a working document or project, and
perform typical production operations such as editing a file and
printing a report. If the application does not work as expected, see
the application’s release notes and documentation to determine the
problem.
120
Chapter 7
Verifying System Install or Update
Changing the State of HP-UX Installed Patches
Changing the State of HP-UX Installed
Patches
The swinstallutility permits the installation of multiple patch bundles
with a deferred configuration. Some of these patch bundles may contain
superseded patches that do not get configured.
After executing swverify \*on your system, these patches show an
“installed” software state in the swagent.logfile. This “installed”
software state is not treated as a warning or error by swverify.
The “installed” patches may present a problem when the current
“applied” patch is removed using swremove. The swremovecommand
does not detect or configure a superseded patch with an “installed”
software state.
Start Task
Follow these steps to check the state of patches currently applied to your
system:
1. List the “SD software state” and “patch state” of both superseded
patches and active (or applied) patches on your system:
/usr/sbin/swlist -a state -a patch_state patch_number
To list all patches, use the command:
/usr/sbin/swlist -a state -a patch_state PH*
For example, the above swlistoptions may show some differences
between an older (superseded) patch and the current (applied) patch
on your system.
NOTE
Superseded patches left in an “installed” SD state do not cause any
problems, but they require an extra swconfigstep when they
become the current “applied” patch.
2. HP recommends that you configure a current “applied” patch in the
“installed” SD state with the following command:
/usr/sbin/swconfig patch_number
Chapter 7
121
Verifying System Install or Update
Changing the State of HP-UX Installed Patches
WARNING
This problem only exists when an active patch is removed
and rolled back to a superseded patch left in an “installed”
state. Executing swconfigon a patch in the “superseded”
patch state is dangerous; do not do it.
3. Use the following options to list active products, patches, and states:
swlist -l fileset -a state -a patch_state
The previous swlistoptions will display all active (non-superseded)
filesets with their “SD software state” and “patch state” attributes.
You can change swlistto display superseded patches by adding the
following line to the /var/adm/sw/defaults file:
swlist.show_superseded_patches=true
or you can use the following command to display superseded patches:
swlist -l fileset -a state -a patch_state -x \
swlist.show_superseded_patches=true
TIP
For help with these commands, see the Software Distributor
Administration Guide, which is available on the Instant Information
DVD and on the web:
http://docs.hp.com/hpux/os/11iv2
122
Chapter 7
Verifying System Install or Update
The Next Step
The Next Step
You have completed the verification process:
•
•
•
“Verifying the HP-UX Install or Update” on page 118
“Changing the State of HP-UX Installed Patches” on page 121
Continue with the next chapter:
Chapter 8, “Installing Patches and Applications,” on page 125
•
Chapter 7
123
Verifying System Install or Update
The Next Step
124
Chapter 7
8
Installing Patches and
Applications
•
•
page 128
•
•
•
“Tips for Installing or Updating HP Applications” on page 131
“Backing Up the System” on page 135
“The Next Step” on page 136
To complete the steps in this chapter, we estimate you require 1-2 hours
per patch and 1-2 hours per application. Time per patch is reduced if you
download and install multiple patches in a single session. Please note
your time may vary.
TIP
This chapter provides installation information for HP-related patches
and applications only. To install or upgrade other vendor patches and
applications, please refer to the appropriate vendor documentation.
You can find the complete list of applications included in the HP-UX 11i
v2 release in the HP Application Availability Matrix:
http://www.software.hp.com/MATRIX
Chapter 8
125
Installing Patches and Applications
Keeping Up to Date with the Latest Critical Patches
Keeping Up to Date with the Latest Critical
Patches
After you installed HP-UX 11i v2, you will have the latest critical
patches installed on your system that shipped with the media.
However, other recommended critical or required patches may have
become available after the initial release of the media. You should check
on a regular, proactive basis to see if Hewlett-Packard has released any
new, recommended critical patches.
HP-UX Patching Resources
You should install any additional recommended critical or required
patches to your base OS and applications which may have occurred since
the initial HP-UX 11i v2 install media was produced.
Using the Custom You can identify and download all needed patches for your system by
Patch Manager
using the HP Custom Patch Manager:
http://itrc.hp.com/wps/bin/doc.pl/sid=00f2dea61cb1fc364e
NOTE
As of this release, use of CPM requires a current support contract or it
may be used on a fee-per-use basis.
If you are already registered, log in with your user ID and password. If
to save your user ID and password.
CPM will identify recommended patches for your system and all required
dependencies. Once you have downloaded needed patches, install them
using the swinstallcommand, as explained in “Installing OS Patches
Required by Individual Applications” on page 128.
126
Chapter 8
Installing Patches and Applications
Keeping Up to Date with the Latest Critical Patches
Downloading
When you need to find and download a single patch, use the HP Patch
Individual Patches Database. Begin at the HP IT Resource Center web site:
http://itrc.hp.com
From the home page, select individual patches.
If you are already registered, log in with your user ID and password. If
you are not registered, follow the instructions on the screen.
From the patch database main page, select HP-UX and use the search tool
to find required patches and download them. You may download patches
individually or as a group. All dependent patches will also be identified.
Once you have downloaded needed patches, install them using the
swinstallcommand as explained in “Adding HP-UX Patches to a
Software Depot or System” on page 129.
HP Security
Bulletins &
Security Patch
Check Tool
To keep informed on newly identified security patches and HP-UX
patches released in a previous week, you can sign up to receive periodic
HP Security Bulletins and weekly HP-UX Patch Digests, respectively. To
subscribe, go to the HP IT Resource Center:
http://itrc.hp.com
Under Maintenance and Support, select subscribe to security bulletins &
patch digests. For security bulletins, register for the HP-UX Security
Bulletins digests, and for all HP-UX patches register for HP-UX 11.X
Patch Digests. Security Patch Check is a tool available for identifying
security patches applicable for your system. For more information on
Security Patch Check, go to the web:
http://www.software.hp.com/cgi-bin/swdepot_parser.cgi/cgi/displayP
roductInfo.pl?productNumber=B6834AA
Other HP-UX
Patching
If you are not familiar with patching HP-UX, documents in the Patch
Management section of the HP documentation web site may be helpful.
Resources
http://docs.hp.com
Go to the operating system or environment version and then search for
patch management. General guidelines for patching HP-UX are provided
in the HP-UX Software Transition Kit:
http://devresource.hp.com/STK/hpuxpatch.html
Also see “Managing Patches” in the Software Distributor Administration
Guide.
Chapter 8
127
Installing Patches and Applications
Installing OS Patches Required by Individual Applications
Installing OS Patches Required by Individual
Applications
If the operating system requires any new HP-UX patches, you can do the
following:
•
•
•
•
•
•
Determine the list of HP-UX patches prior to cold-install
Obtain the newer HP-UX patches
Get the HP-UX patch information
Remove HP-UX patches, if necessary
Add newer HP-UX patches, if necessary
Keep up to date with the latest critical patches
Determining the List of Previous HP-UX patches
New or replacement patches may be required as dependencies for
application software installed on your system. Before removing a patch
or a patch bundle, determine the dependencies required by the installed
software. You can find this information in the release notes for the
to remove some installed software from your system.
Obtaining Newer HP-UX patches
To obtain newer patches, see the “HP-UX Patching Resources” on
page 126.
Getting HP-UX Patch Information
For information on individual patches in a patch bundle, use swlist (1M)
to list the readmeattribute at the product level.
Start Task
1. From the depot, log in as root and enter the command:
/usr/sbin/swlist -s /temp/depot_name -l product -a readme
patch_name
128
Chapter 8
Installing Patches and Applications
Installing OS Patches Required by Individual Applications
2. From your system, enter the command:
/usr/sbin/swlist -l product -a readme patch_name
Removing HP-UX Patches
To remove any patches from your system, you must first determine
which patches are installed.
1. To display installed patches, enter the command:
/usr/sbin/swlist -l patch \*.\*,c=patch
2. To preview the removal analysis, enter the command:
/usr/sbin/swremove -p patch_name1 patch_name2 ...
3. You must interpret patch dependencies manually from the patch
documents, that is, the patch_name.txt files.
CAUTION
In rare cases, you may have to remove a patch from your system.
Generally, a newer patch should just be installed over a superseded
patch. You should take extreme caution before ever removing a patch
from your system. Always check for patch dependencies before
attempting to remove any patch. The swremovewill not do automatic
patch dependency checking for you like the swinstallcommand does.
Adding HP-UX Patches to a Software Depot or System
For help on adding patches see the Software Distributor Administration
Guide, which is available on the Instant Information CD and on the web:
http://docs.hp.com/hpux/os/11v2
General guidelines for patching HP-UX are provided in the HP-UX
Software Transition Kit:
http://devresource.hp.com/STK/hpuxpatch.html
The following instructions are a general review of installing patches; see
the “HP-UX Patching Resources” on page 126 for more information.
Start Task
Chapter 8
If you are already running an HP-UX 11i v2 system, you can run
swinstallinteractively and see the contents of the depot online:
129
Installing Patches and Applications
Installing OS Patches Required by Individual Applications
1. On the system, run swinstallinteractively:
/usr/sbin/swinstall
2. Highlight the patch bundle to select it, or individual patches and
press Return/Enter. This opens the patch bundle to the product level.
3. For any given product (shown as a patch number):
a. Highlight the product line to select it.
b. Select Actions -> Show Description of Software. This generates a
Software Description Dialogue box.
c. From the Software Description Dialog box, select Readme. This
generates the Readme Viewer Dialog box, through which you can
scroll to find the following:
•
•
•
•
•
•
•
Affected filesets
Reboot requirement for the patch
Category tags used to create the patch
Symptoms the patch addresses
Description of the defect being fixed
Patch files and dependencies
Instructions for installing an individual patch
4. To find out which patches are in a specific category tag, use swlist.
For example, to list the patches (by product name) for all patches
categorized as hardware enablement, enter the command:
/usr/sbin/swlist -d -l product *,c-hardware_enablement \
@ host:deport
TIP
Each patch comes with installation instructions and in some cases
“special installation” instructions. For example, when installing patches,
it is recommended that certain SD options be selected so that only
patches applicable to the target system are loaded.
130
Chapter 8
Installing Patches and Applications
Tips for Installing or Updating HP Applications
Tips for Installing or Updating HP
Applications
In the previous chapters of this guide, you installed HP-UX 11i v2,
installed additional patches if necessary, and verified the system. Now
you should install and/or update other needed HP, non-OS applications.
Here are some tips:
•
To determine which products and versions are on your system use
the swlistcommand:
/usr/sbin/swlist -l product
•
HP-UX Applications DVDs have an ASCII file on each DVD called
the Applications DVD. This ASCII file is viewable with vi,emacs, or
any other text editor.
•
•
To verify that all installed products are compatible with the new OS,
run swverifyas explained in “Verifying the HP-UX Install or
Update” on page 118.
Use swinstallto install new software or update each application
not included in the HP-UX 11i v2 OS and OE you just installed. The
latest versions of many HP-UX software products are provided on the
HP-UX Applications DVD. To find the contents of each DVD, mount
any HP-UX Applications DVD and view the TABLE_OF_CONTENTSfile.
For swinstallinstructions, see the next section.
•
•
Installation of application patches and applications may occur in the
same swinstallsession to save on the number of required reboots.
For HP applications, there exists documentation that shows you how
to install and use an application. The documents may include release
notes, readme files, DVD and CD booklets, white papers, and guides.
See the Instant Information CD and the web:
http://docs.hp.com
Chapter 8
131
Installing Patches and Applications
Tips for Installing or Updating HP Applications
Installing Optional Software Products
The Applications DVD that is distributed with HP-UX 11i v2 contains
optional development tools and system management software.
HP-UX 11i v2 must be booted in order to install optional software
products. The following is the procedure for installing products from the
Applications DVD.
Step 1. Insert the Applications DVD in the DVD-ROM drive.
Step 2. Mount the Applications DVD.
To install software from the Applications DVD, you must mount the
DVD as a filesystem that HP-UX 11i v2 can access.
a. Determine the DVD device name.
Use the ioscan -funC diskcommand to list disk devices, including
the DVD devices.
b. Create a mount point for the Applications DVD, if one does not yet
exist.
The mount point is a directory that HP-UX will use as an access
point for the DVD. Often a /cdromdirectory is used. If this directory
does not exist, create it using the mkdir /cdromcommand.
c. Use the mountcommand to mount the DVD.
Using the mountcommand, specify the DVD device name and mount
point. For example, the following command mounts the
/dev/dsk/c1t0d0device as the /cdromdirectory.
mount /dev/dsk/c1t0d0 /cdrom
See the mount (1M) manpage for details.
Step 3. Use swinstallto install software from the Application DVD.
The following example command runs swinstallto install software
from the source mounted at /cdrom.
swinstall -i -s /cdrom
See the swinstall (1M) manpage for details.
Step 4. Select and install software from the Applications DVD.
132
Chapter 8
Installing Patches and Applications
Tips for Installing or Updating HP Applications
The swinstallprogram presents an interface for selecting and
installing software from the DVD.
Step 5. Unmount and eject the Applications DVD.
You must unmount the DVD before you can eject it from the DVD-ROM
drive. The DVD is automatically unmounted whenever the server
reboots.
Use the umountcommand to unmount the DVD. For example,
umount /cdromwill unmount the /cdromfile system. See the umount
(1M) manpage for details.
Using Ignite-UX
You can use the Ignite-UX utility to install HP-UX applications on
systems using a local mount directory, or over a network using an
Ignite-UX server. Ignite-UX is an HP-UX product that facilitates
installing and configuring HP-UX systems.
See the Ignite-UX Administration Guide for detailed instructions on how
to install HP-UX applications. It is on the Instant Information DVD and
on the web:
http://docs.hp.com/hpux/os/11v2
Ignite-UX can address your need to perform system installations and
deployment, often on a large scale. With Ignite-UX, you can do the
following:
•
•
Create and reuse standard system configurations.
Archive a standard system configuration and use that archive to
replicate systems in far less time than with other methods.
•
•
Create customized processes to allow interactive and unattended
installs.
Recover OS and applications more easily after crashes and hardware
failures.
For example, you can install the Ignite-UX utilities to install HP-UX and
applications on other systems:
1. Mount the HP-UX 11i v2 DVD containing Ignite-UX (mount point is
assumed here to be /cdrom) and enter the command:
/usr/sbin/swinstall -s /cdrom B5725AA
Chapter 8
133
Installing Patches and Applications
Tips for Installing or Updating HP Applications
2. After installing the software, see the Ignite-UX release notes and
Ignite-UX Administration Guide to complete any post-install steps
and configuration.
After running an Ignite-UX install session, you have a working HP-UX
client system.
134
Chapter 8
Installing Patches and Applications
Backing Up the System
Backing Up the System
Now that you have a solid system configuration, you need to back it up.
This provides you with a stable configuration that you can use to rebuild
the system, if necessary.
You can use the Ignite-UX product for making a system recovery backup.
See the Ignite-UX Administration Guide:
http://docs.hp.com/hpux/os/11iv2
Depending on your work environment, you can use the following
commands:
• fbackupand frecoverto create a backup archive and frecoverto
restore the system, if necessary
•
Ignite-UX commands: make_net_recoveryand
make_tape_recovery
Chapter 8
135
9
Configuring and Maintaining
HP-UX 11i v2
needs. Before you begin you should have already completed the install or
chapters.
What You Will Find in This Chapter
•
•
“Configuring Your HP-UX 11i v2 System” on page 138
“Maintaining Your HP-UX 11i v2 System” on page 140
To complete the steps in this chapter, we estimate you require 2-4 hours
to configure the system while the time to maintain your system is
ongoing. Please note that your time may vary.
Chapter 9
137
Configuring and Maintaining HP-UX 11i v2
Configuring Your HP-UX 11i v2 System
Configuring Your HP-UX 11i v2 System
Now that you have installed or updated HP-UX 11i v2 and any
additional software and patches, your next task is to configure your
system. You can find many of these tasks in Managing Systems and
Workgroups: A Guide for HP-UX System Administrators.
The following list breaks these tasks into several categories to assist you
in finding the information you need:
•
Networking and Connectivity
— Manually setting system information: Use the set_parms
command to configure your system’s hostname, IP Address,
DNS, and other network and system data. For more information
about set_parms, see the Managing Systems and Workgroups: A
•
File System Administration
— Small Memory Systems (less than 1GB/CPU RAM): If you have
less than 1GB/CPU of memory, please see Appendix C,
“Controlling Memory Utilization of VxFS 3.5 on HP-UX 11i v2,”
on page 155 for details about optimizing VxFS for your system.
— Setting Up File Systems: Depending on how you want to manage
your physical volumes, choose one of the following:
— LVM: See the Managing Systems and Workgroups: A Guide
for HP-UX System Administrators on http://docs.hp.com.
— VxVM: See the VERITAS Volume Manager 3.5
Administrator’s Guide on the Veritas web site
— Network File Systems (NFS): If you want to make local
directories available to other hosts on the network, see Installing
and Administering NFS Services on http://docs.hp.com
•
Managing Users and Groups
— Adding Users and Groups: See Managing Systems and
Workgroups: A Guide for HP-UX System Administrators on
http://docs.hp.com
138
Chapter 9
Configuring and Maintaining HP-UX 11i v2
Configuring Your HP-UX 11i v2 System
•
•
Printers and Peripherals
— Printers: See Managing Systems and Workgroups: A Guide for
HP-UX System Administrators on http://docs.hp.com.
— Peripherals: See Configuring HP-UX for Peripherals
Other Tasks
You can find information about other tasks for HP-UX 11i v2 at
http://docs.hp.com/hpux/os/11iv2
Chapter 9
139
Configuring and Maintaining HP-UX 11i v2
Maintaining Your HP-UX 11i v2 System
Maintaining Your HP-UX 11i v2 System
The following flowchart offers a recommended method for maintaining
your HP-UX 11i v2 system using the HP software support services.
Figure 9-1
Reactive Software Maintenance
rd
Receive New 3 Party
Encounter Problem
Software
Search patch database
on
Download Patches
http://itrc.hp.com
Update or create new
install depot *
Download Patches
Install new version of
software
Update or create new
install depot *
Update software using
swinstall with
match_patch_target
Create
archive/recovery
image
* For help creating depots, see the Software Distributor Administration Guide.
Depots can contain applications from the HP-UX Application DVDs.
140
Chapter 9
A
Data Collection Tables
Network Data and Miscellaneous Data collection tables.
What You Will Find in This Appendix
•
•
“Network Data Collection Table” on page 142
“Miscellaneous Data Collection Table” on page 143
NOTE
These additional points should help you determine when to use the
collection tables:
•
If you chose the Guided Install, the HP-UX Install Wizard prompts
you for the data in these tables at various stages during the install.
•
If you chose the Advanced Install, an interface gives you the
opportunity to enter all of this data at the beginning of the install.
The interface is a tabbed file-folder and character-based.
•
If you choose to network-enable your system, you must designate a
unique host name, host Internet Protocol (IP) address, and other
network information for your server or workstation.
Talk to your site network administrator for the details to include in
these tables.
Appendix A
141
Data Collection Tables
Network Data Collection Table
Network Data Collection Table
The following Network Data collection table provides HP-UX commands
that you can use after the install to confirm specific information.
Table A-1
Enter Network Data
HP-UX command to
Type of Data
Enter Your Specific Data
confirm data after system
is up and running
Host Name
uname -n
Host IP Address
nslookup name
Subnet Mask
grep SUBNET_MASK
/etc/rc.config.d/netconf
Default
netstat -r
Gateway IP
Address
Domain Name
cat /etc/resolv.conf
cat /etc/resolv.conf
DNS IP
Address
NIS Domain
Name
grep NIS_DOMAIN
/etc/rc.config.d/namesvrs
142
Appendix A
Data Collection Tables
Miscellaneous Data Collection Table
Miscellaneous Data Collection Table
The following Miscellaneous Data collection table may contain some
items that are not familiar to you, but they are all questions that you will
be asked during the install.
The install process describes all options in detail, so you can defer
making decisions about those items unfamiliar to you until you reach
that point in the install.
Table A-2
Enter Miscellaneous Data
Type of Data
Type of Desktop
Enter Your Specific Data
Root DiskPath
Root Swap Space
Filesystem Type
LVM, VxVM w/VxFS, or Whole disk
with VxFS
Root Disk Volume Group Disks
(How many disks you want placed
into the root disk volume group and
whether or not you want the disks
to be striped?)
Select additional software
(All, HP-UX Additions,
Uncategorized)
Pre-Installed Disk Information
(Is overwritten during the install
disk, see Root Disk Path) This is a
“review” confirmation step.
Appendix A
143
Data Collection Tables
Miscellaneous Data Collection Table
144
Appendix A
B
Known Problems and
Troubleshooting
install and update.
•
•
•
•
“Known Install/Update Problems” on page 146
“Uninstalling HP-UX 11i v2” on page 151
“Restrictions with Netscape Communicator” on page 152.
“Character-code Handling with Perl” on page 153
NOTE
As the HP-UX 11i v2 install progresses, you will see messages relating to
the progress being entered into the log file. These messages usually refer
to normal behavior. The ERROR, WARNING, and NOTEmessages, however,
have the following significance:
ERROR
WARNING
NOTE
Indicates a serious problem, usually requiring action
from you in order to proceed with an installation.
Indicates something out of the ordinary, but not fatal.
The warning may require action from you.
Indicates something out of the ordinary, but not fatal.
The note does not require action from you.
Appendix B
145
Known Problems and Troubleshooting
Known Install/Update Problems
Known Install/Update Problems
The following problems are known to occur in the HP-UX 11i v2 release.
HP CIFS Server Product
The new version of the HP CIFS Server A.01.09.04 is based on Samba
2.2.5 and is available on HP-UX 11i v2 release. Please refer to the HP
CIFS Server 2.2e (version A.01.09.04) Release Notes for new features,
known problems, and workarounds for this product. The CIFS Server
2.2e (version A.01.09.04) Release Notes are available in the Networking
and Communication Section of the HP document web site:
http://docs.hp.com
Known Issues with OE Media Install Tool and
Network Depots
The Ignite-UX install tool on the OE media supports the use of network
depots. However, network depots must match the media depots for the
choices in the install tool to work properly.
The Ignite-UX documentation also explains the setup and use of network
depots without using the OE media for each installation. See the
following web site for information on the Ignite-UX product:
http://software.hp.com/products/IUX
Error Message When Trying to Ignite an HP-UX 11i
v1.6 System with an HP-UX 11i v2 Ignite-UX Server
If you are trying to install HP-UX 11i v2 on an HP-UX 11i v1.6 system
from an HP-UX 11i v2 Ignite-UX server, you may see the following error
message if your HP-UX 11i v1.6 system is using VxVM:
ERROR: VxVM installs of 11.22 are not supported with the 11.23 or
later install kernel due to VxVM 3.5 versus 3.1
incompatibilities. The VxVM disk group “rootdg” must be
changed to LVM or whole-disk or be removed
146
Appendix B
Known Problems and Troubleshooting
Known Install/Update Problems
How Do You Know If your current system is running HP-UX 11i v1.6 and VxVM, and you
If This Affects You attempt to install HP-UX 11i v2 from an Ignite-UX server, you will
receive this message.
What to Do
Because of incompatibilities between VxVM 3.1 (on HP-UX 11i v1.6) and
VxVM 3.5 (on HP-UX 11i v2), you can not install HP-UX 11i v2 on an
HP-UX 11i v1.6 system running VxVM 3.1 from an Ignite-UX server.
Instead, you can do one of the following:
•
Change your volume manager to LVM or Whole Disk, and retry
installing HP-UX 11i v2 from the Ignite-UX server.
•
Install HP-UX 11i v2 from the DVD media.
For more information, please see the Ignite-UX website:
http://software.hp.com/products/IUX
HIDS Becomes Unbundled during Update
The following warning message may appear in your swagent.logafter
the update process, or from running swverify.
From swagent.log:
* [20255] Running “checkinstall” script for fileset
“IDS.IDS-AGT-KRN”.
WARNING: Excluding fileset IDS-AGT-KRN because the IDDS driver is
already configured. An unbundled IDS-AGT-KRN fileset may
result. If your system contains an unbundled IDS-AGT-KRN
fileset, the installation, configuration and operation of
HP-UX Host IDS is not affected. You can safely ignore the
unbundled IDS-AGT-KRN fileset.
NOTE:
[20259] The “checkinstall” script for “IDS.IDS-AGT-KRN
gave an “exclude” return (exit code “3”). The script location was
“/var/tmp/BAAa04878/catalog/IDS.2/IDS-AGT-KRN/checkinstall”.
NOTE:
[140257] This software will be excluded from further
processing.
* [20255] Running “checkinstall” script for fileset
“IDS.IDS-ADM-RUN”.
From swverify:
ERROR: [140167] The product “IDS,l=/opt/ids,r=C.02.01.44” is not
compatible with this system’s architecture or operating
system. If the OS has been updated since this product was
installed, a newer version should be installed if available
* [140061]
Configured
IDS.IDS-AGT-KRN,l=/opt/ids,r=C.02.01.44
Appendix B
147
Known Problems and Troubleshooting
Known Install/Update Problems
How Do You Know If you update your system to HP-UX 11i v2 from either HP-UX 11i v1.6
If This Affects You or HP-UX 11i v2, you will encounter this error message.
The problem is caused by an ‘orphaned’ fileset IDS-AGT-KRNleft on your
system in order to prevent an unnecessary reboot, and results in
swverifyerrors after the update.
What to Do
You can safely ignore this message. HIDS will work properly. However,
if you want to ensure a clean installation of IDS:
1. Save any customization files to a safe location
2. Use the swremovecommand to remove HIDS (J5083AA)
3. Use the swinstallcommand to install HIDS (J5083AA) from the
HP-UX 11i v2 media.
“Incorrect protocol version (20) in volboot file” Error
After updating to HP-UX 11i v2 from HP-UX 11i v1.6, the following error
message may appear during reboot:
Starting vxconfigd in boot mode (pre_init_rc).
vxvm:vxconfigd: WARNING: volboot: Incorrect protocol version (20)
in volboot file.
vxvm:vxconfigd: WARNING: volboot: Using the highest supported
protocol version 40
Checking root file system.
How Do You Know You will encounter this error if you updated an HP-UX 11i v1.6 system
If This Affects You with VxVM 3.1 as your volume manager to HP-UX 11i v2 with VxVM
3.5. The problem is caused by different version values in the volbootfile
(20in VxVM 3.1; 40in VxVM 3.5
What to Do
You can safely ignore this error message.
“Unable to flush file system metadata for /stand to
disk” Warning
The following warning message will appear just before your system
reboots after updating to HP-UX 11i v2 from HP-UX 11i v1.6:
WARNING: Unable to flush file system metadata for /stand to
disk
148
Appendix B
Known Problems and Troubleshooting
Known Install/Update Problems
How Do You Know The problem occurs after updating to HP-UX 11i v2 from HP-UX 11i
If This Affects You v1.6. During the reboot after the update, the HP-UX 11i v2 Update-UX
kernel attempts to reboot the system.
While the system has been updated with HP-UX 11i v2 bits, the system
kernel is still running as HP-UX 11i v1.6 before the reboot. You will
encounter this warning message because of differences between the
Update-UX kernel and system kernel commands used to shut down your
system.
What to Do
You can safely ignore this warning message.
mod_load_helperError
After updating from HP-UX 11i v1.6 to HP-UX 11i v2, you may see the
following dmesgor syslogerror:
MOD: mod_load_helper:gvid_him_fgl(gvid_him_fgl):_load returned
error 13
What to Do
You can safely ignore this error.
/stand/ioconfigRead Warning
After cold-installing HP-UX 11i v2, you may see the following warning
message while rebooting your system:
Booting kernel
WARNING: GIO: read_ioconfig_file(): /stand/ioconfig read
error.
ioconfig = NULL
NOTICE: cachefs_link(): File system was registered at index 4.
NOTICE: nfs3_link(): File system was registered at index 7.
td: claimed Tachyon XL2 Fibre Channel Mass Storage card at
0/2/1/0
igelan1: INITIALIZING HP PCI 1000Base-T Core at hardware path
0/1/2/
How Do You Know This problem occurs on new installed kernels because there is no
If This Affects You ioconfigfile from a previous boot. GIOissues the warning because it
cannot find an ioconfigfile.
What to Do
You can safely ignore this warning.
Appendix B
149
Known Problems and Troubleshooting
Known Install/Update Problems
No Dump Devices Configured Warning
After cold-installing HP-UX 11i v2, you may see the following warning
message while rebooting your system:
WARNING: No dump devices are configured. Dump is disabled.
Starting the STREAMS daemons-phase 1
execve(“/sbin/sh”) failed, errno 0xffffffff
execve(“/bin/sh”) failed, errno 0xffffffff
Create STCP device files
Starting the STREAMS daemons-phase 2
What to Do
You can safely ignore this warning.
150
Appendix B
Known Problems and Troubleshooting
Uninstalling HP-UX 11i v2
Uninstalling HP-UX 11i v2
If you cannot resolve problems after installing HP-UX 11i v2, then you
may want to un-install it. The process depends upon the install process
you followed:
•
Assuming that you have made a make_net_recoverytape using
Ignite-UX, boot the system from that media to return the OS and any
archived applications to the previous release. This is covered in
Chapter 11 of the Ignite-UX Administration Guide, available on the
Instant Information DVD and on the web:
http://docs.hp.com
If you do not use Ignite-UX or do not have a current
make_net_recoverytape, read on....
•
•
If your applications and data are on a separate disk from the OS,
cold-install the previous OS. This ensures a clean OS installation,
removing all previous upgrade and patch information.
If applications and/or data are on the same volume with the OS, boot
from the previously-saved system recovery tape to return to a
previous OS. These “expert recovery” processes are in Chapter 11 of
the Ignite-UX Administration Guide.
To determine which applications are on the system and where they are
located, use swlist. If you only need to remove applications or patches
from the system, use swremove. See the Software Distributor
Administration Guide for details.
Appendix B
151
Known Problems and Troubleshooting
Restrictions with Netscape Communicator
Restrictions with Netscape Communicator
Netscape 4.x Unbundles during Update
When updating from HP-UX 11i v1.6 to HP-UX 11i v2, Netscape 4.x will
become unbundled. You may see an error message similar to the
following after running swverify:
# Product(s) not contained in a Bundle:
# NS-communicate B.11.00.01 Netscape Communicator 4.79
What to Do
You can still use the product, but it will not swverifycorrectly. Netscape
4.x is not supported on HP-UX 11i v2, so we recommend you upgrade to
the Mozilla Application Suite.
For more information, see the web site:
http://www.hp.com/go/mozilla
Netscape 7.0 Aborts with ja_JP.utf8 Locale
Netscape 7.0 aborts immediately or soon after it is invoked in ja_JP.utf8.
What to Do
Select another Japanese locale. To see which locales are available, use
the locale -acommand.
For more information see locale (1).
152
Appendix B
Known Problems and Troubleshooting
Character-code Handling with Perl
Character-code Handling with Perl
Although Perl 5.6.1 does not directly support wide characters, its
experimental support of Unicode may be a suitable solution. JPerl
5.005_003 is another solution to handle Japanese multi-byte characters
albeit by an older version of Perl.
What to Do
Get the patch jperl5.005_03and apply it to Perl. This patch is open
source and available at a number of non-HP FTP sites.
Follow these steps:
Step 1. Get the Perl 5.005_03 source files from http://devresource.hp.com
Step 2. Download patch jperl5.005_03from an open-source Perl site.
Step 3. Apply the patch to the source code, and build it.
NOTE
Once patched with jperl5.005_003, you cannot use Perl as Mod_perl
under the HP Apache-based Web server.
Appendix B
153
Known Problems and Troubleshooting
Character-code Handling with Perl
154
Appendix B
Controlling Memory Utilization of VxFS 3.5 on HP-UX 11i v2
C
Controlling Memory Utilization
of VxFS 3.5 on HP-UX 11i v2
on setting them for machines with relatively low RAM.
•
•
•
•
“Introduction” on page 156
“Controlling the inode Cache” on page 157
“Controlling the Buffer Cache” on page 158
“Conclusion” on page 159
Appendix C
155
Controlling Memory Utilization of VxFS 3.5 on HP-UX 11i v2
Introduction
Introduction
VxFS 3.5 resorts to caching objects in memory as a way to improve
performance. Most of the memory consumed by VxFS is used to cache
inodes (in the inode cache) and metadata (in the buffer cache). The sizes
of these caches and the behavior of VxFS are controlled by a set of
tunables. You can tailor the performance of VxFS to meet a variety of
usage scenarios while taking into account variations in machine
configurations via the use of these tunables.
The default settings of these tunables are meant to provide good
performance for typical deployment configurations. However, these
default values can result in the VxFS driver consuming more memory,
especially when the file systems are stressed (under heavy file system
load). For machines low on RAM, these tunables may need to be
manually turned down depending on the expected use of the machine
and the performance required of the file system.
VxFS 3.5 exposes two global tunables, vx_ninodeand vx_bc_bufhwm,
that control the size of the inode cache respectively and thereby affect
system memory consumption by the file system driver.
This appendix discusses when and why the sizes of the inode and buffer
caches need to be tuned down from their default values in certain
configurations. The following sections describe these tunables in detail
as well as the effects of changing their default values.
156
Appendix C
Controlling Memory Utilization of VxFS 3.5 on HP-UX 11i v2
Controlling the inode Cache
Controlling the inode Cache
As a matter of course, VxFS file systems allocate and free up inodes as
required by the load on the file system. VxFS caches these inodes for
better performance (faster lookups). In general, larger inode caches help
file systems perform better for file/web server loads. The global (static)
tunable vx_ninoderepresents the maximum possible size of the VxFS
inode cache.
Normally, the size of the inode cache is decided (auto-tuned) at boot time
by VxFS depending on the amount of physical memory in the machine,
provided that the value of vx_ninodeis set to zero (default).
However, systems low on RAM (typically less than or equal to 1GB/CPU)
may not require a large inode cache if file systems are not exposed to
file/web server loads, or file system performance is not critical. It is
recommended that the value of vx_ninodebe set to more than that of
nfile, an HP-UX tunable that represents the maximum number of file
descriptors.
Appendix C
157
Controlling Memory Utilization of VxFS 3.5 on HP-UX 11i v2
Controlling the Buffer Cache
Controlling the Buffer Cache
VxFS 3.5 implements a private buffer cache used exclusively for
metadata. The allocations made for this buffer cache are not static but
grow and shrink during system usage, depending on the load on the file
system. The global (static) tunable vx_bc_bufhwmrepresents the
maximum possible size of the VxFS buffer cache.
The maximum size of the metadata buffer cache is decided (auto-tuned)
at boot time based on system memory size, provided that the value of
vx_bc_bufhwmis set to zero (default).
As with the tunable vx_ninode, a large metadata buffer cache can help
improve file system performance especially during metadata-intensive
loads (stat, create, remove, link, lookup operations).
However, systems low on RAM (having typically 1GB/CPU or less) may
not need a large metadata buffer cache if the file system load is not
metadata-intensive or performance is not critical. In such circumstances,
the value of vx_bc_bufhwmcan be manually tuned down, subject to a
minimum of 6144 (6MB).
158
Appendix C
Controlling Memory Utilization of VxFS 3.5 on HP-UX 11i v2
Conclusion
Conclusion
VxFS uses in-memory caches for objects that result in improved file
system performance. The cache sizes are controlled by tunables that are
auto-tuned at boot time by the driver. For situations where the
auto-tuned values are not optimal, you are provided with the ability to
set these tunables.
Appendix C
159
Controlling Memory Utilization of VxFS 3.5 on HP-UX 11i v2
Conclusion
160
Appendix C
Software Distribution Media
HP-UX 11i v2 Operating Environments at a Glance
HP-UX 11i v2 Operating Environments at a
Glance
Overview
Operating Environments are tested and integrated application bundles
designed to work with the operating system and provide the
functionality needed for your system’s purpose. The following lists the
currently available HP-UX 11i v2 OEs:
•
•
•
HP-UX 11i v2 Foundation Operating Environment (FOE) —
Designed for the demands of Web servers, content servers and
front-end servers, this OE is provided at no-charge and includes
applications such as HP-UX Web Server Suite, Java, and Mozilla
Application Suite. This OE is bundled as HPUX11i-OE.For more
details, see “HP-UX 11i v2 Foundation OE (FOE)” on page 163.
HP-UX 11i v2 Enterprise OE (EOE) — Designed for database
application servers and logic servers, this OE is an extra-cost
package containing the HP-UX 11i Foundation OE and additional
applications such as GlancePlus Pak to enable an enterprise-level
server. This OE is bundled as HPUX11i-OE-ENT. For more details, see
“HP-UX 11i v2 Enterprise OE (EOE)” on page 165.
that access customer files and handle transaction processing, this
OE is an extra-cost package containing the Enterprise OE, plus
applications such as MC/ServiceGuard and Workload Manager to
enable a mission-critical server. This OE is bundled as
HPUX11i-OE-MC.For more details, see “HP-UX 11i v2 Mission
Critical OE (MCOE)” on page 166.
•
HP-UX 11i v2 Minimal Technical OE (MTOE) — Designed for
workstations running HP-UX 11i v2, this OE is provided at no
charge and includes the Mozilla Application Suite, Perl, VxVM, and
Judy applications, plus the OpenGL Graphics Developer’s Kit. This
OE is bundled as HPUX11i-MTOE.For more details, see “HP-UX 11i
v2 Minimal Technical OE (MTOE)” on page 166.
162
Appendix D
Software Distribution Media
HP-UX 11i v2 Operating Environments at a Glance
•
(TCOE) — Designed for both compute-intensive workstation and
server applications, this OE is an extra-cost package containing the
MTOE plus extensive graphics applications and Math Libraries.
This OE is bundled as HPUX11i-TCOE. For more details, see “HP-UX
11i v2 Technical Computing Operating Environment (TCOE)” on
page 168.
The following table details the supported operating environments for HP
Servers and Workstations.
The operating environments are represented as follows:
FOE
Foundation Operating Environment
EOE
Enterprise Operating Environment
MCOE
MTOE
TCOE
Mission Critical Operating Environment
Minimum Technical Operating Environment
Technical Computing Operating Environment
Table D-1
Supported Operating Environments
1
FOE
EOE
MCOE
MTOE
TCOE
HP Commercial Servers
X
X
X
X
X
HP Workstations
X
(and Technical Servers)
1. You can use TCOE on either workstations or compute-intensive
technical servers.
HP-UX 11i v2 Foundation OE (FOE)
The HP-UX 11i v2 Foundation Operating Environment is the standard
OE from which the Enterprise OE and Mission Critical OE have been
derived by adding appropriate applications. The HP-UX 11i v2
Foundation OE includes the base 64-bit HP-UX operating system, plus
the following features:
Appendix D
163
Software Distribution Media
HP-UX 11i v2 Operating Environments at a Glance
Always-Installed Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Event Monitoring System
FDDI (PCI)
FibreChannel (PCI)
Gigabit Ethernet (PCI)
Gigabit Ethernet Next Generation (PCI)
HP CIFS Client
HP CIFS Server
HP WBEM Services for HP-UX
HP-UX Kernel Configuration
iEther (PCI)
instant Capacity on Demand
Logical Volume Manager
nPartition Provider
ONC+
Online Diagnostics
PAM Kerberos
Peripheral Device Tool
Runtime Plug-in (JPI) for Netscape/Mozilla for the Java 2 Platform
v1.3 and v1.4
•
•
•
•
•
•
SCSI U320-00
Software Distributor
SWGETTOOLS
Update-UX
VERITAS File System (base VxFS/JFS)
VERITAS Volume Manager (base)
Default-Installed Features
•
•
•
•
•
GTK+ Libraries
HP-UX Bastille
HP-UX IPFilter
HP-UX Secure Shell
HP-UX Web Server Suite (including HP-UX Apache-based Web
Server, HP-UX Tomcat-based Servlet Engine, HP-UX Webmin-based
Admin, and HP-UX XML Web Server Tools)
Install-Time Security
Java SDK v1.3 and v1.4
Judy Libraries
Mozilla Application Suite
Mozilla Source
•
•
•
•
•
•
MySQL
164
Appendix D
Software Distribution Media
HP-UX 11i v2 Operating Environments at a Glance
•
•
•
•
•
•
Netscape 7
Partition Manager
Perl
Runtime Environment (RTE) for the Java 2 Platform v1.3 and v1.4
Secure Patch Check
Servicecontrol Manager
Selectable Features
•
•
•
•
•
•
•
•
•
•
•
•
•
ATM-00
HP-UX Host Intrusion Detection System (HIDS) (servers only)
HP-UX Install Utilities
HyperFabric
Ignite-UX
Java (Out of Box) Tunable
Pay Per Use
PCI MUX
Security Level 10
Security Level 20
Security Level 30
Software Package Builder
Token Ring
The HP-UX 11i v2 Enterprise Operating Environment (EOE) is targeted
especially for database application servers and logic servers. In addition
to the features found in the HP-UX 11i v2 Foundation Operating
Environment (described in “HP-UX 11i v2 Foundation OE (FOE)” on
page 163), the Enterprise OE includes the following additional features:
Always-Installed Features
•
•
•
•
•
Event Monitoring Service
MirrorDisk/UX
GlancePlus Pak
HP Process Resource Manager
Default-Installed Features
See “HP-UX 11i v2 Foundation OE (FOE)” on page 163
•
Appendix D
165
Software Distribution Media
HP-UX 11i v2 Operating Environments at a Glance
Selectable Features
•
See “HP-UX 11i v2 Foundation OE (FOE)” on page 163
HP-UX 11i v2 Mission Critical OE (MCOE)
The HP-UX 11i v2 Mission Critical Operating Environment (MCOE) is a
high-availability Operating Environment for HP servers. In addition to
the features found in the Foundation and Enterprise operating
environments, the Mission Critical OE includes the following features:
Always-Installed Features
•
•
•
•
•
•
Enterprise Cluster Master Toolkit
MC/ServiceGuard
MC/ServiceGuard NFS Toolkit
Cluster Object Manager
Workload Manager
Workload Manager Toolkits
Default-Installed Features
See “HP-UX 11i v2 Foundation OE (FOE)” on page 163
•
Selectable Features
See “HP-UX 11i v2 Foundation OE (FOE)” on page 163
•
HP-UX 11i v2 Minimal Technical OE (MTOE)
The Minimal Technical Operating Environment (MTOE) is the smallest
and most fundamental OE that is defined specifically for HP
workstations. It exists to offer an HP-UX 11i v2 solution to the customer
who is interested in a low-cost HP Workstation and a correspondingly
basic Operating Environment. The Minimal Technical Operating
Environment is directed to the Workstation OEM market and to those
customers for whom the Technical Computing Operating Environment
(TCOE) is not a suitable solution.
The MTOE contains all the base functionality that is common to the
other four OEs, including the base 64-bit HP-UX Operating System,
network drivers, and some of the other always-installed features.
However, compared to the Technical Computing Operating
Environment, the set of additional features is greatly reduced.
166
Appendix D
Software Distribution Media
HP-UX 11i v2 Operating Environments at a Glance
The MTOE is positioned to deliver a lean set of high-demand
applications that do not increase purchase cost, support cost, or license
cost over the base operating system.
The HP-UX 11i v2 Minimal Technical Operating Environment includes
the following features:
Always-Installed Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Event Monitoring System
FDDI (PCI)
FibreChannel (PCI)
Gigabit Ethernet (PCI)
Gigabit Ethernet Next Generation (PCI)
HP WBEM Services for HP-UX
HP-UX Kernel Configuration
iEther (PCI)
instant Capacity on Demand
nPartition Provider
ONC+
Online Diagnostics
OpenGL
Peripheral Device Tool
SCSI U320-00
Software Distributor
Technical System Configuration (TechSysConf)
SWGETTOOLS
Update-UX
USB
VERITAS File System (base VxVS/JFS)
VERITAS Volume Manager (base)
Default-Installed Features
See “HP-UX 11i v2 Foundation OE (FOE)” on page 163
•
Selectable Features
See “HP-UX 11i v2 Foundation OE (FOE)” on page 163
•
Appendix D
167
Software Distribution Media
HP-UX 11i v2 Operating Environments at a Glance
HP-UX 11i v2 Technical Computing Operating
Environment (TCOE)
Like the Minimal Technical Operating Environment, the Technical
Computing Operating Environment (TCOE) contains all the base
functionality that is common to the other four OEs, including the base
32/64-bit HP-UX Operating System, network drivers, and other
always-installed functionality. While it is not a superset of the
Foundation 11i v2 OE, it is a superset of the Minimal Technical OE.
Unlike the Minimal Technical OE, however, the Technical Computing
OE is available on both technical servers and workstations.
In addition to the features found in the HP-UX 11i v2 Minimal Technical
OE, the HP-UX 11i v2 Technical Computing Operating Environment
includes the following features:
Always-Installed Features
•
•
•
•
HP CIFS Client
HP CIFS Server
PAM Kerberos
Runtime Plug-in (JPI) for Netscape/Mozilla for the Java 2 Platform
v1.3 and v1.4
•
•
•
HP MLIB
HP Message Passing Interface (MPI)
Default-Installed Features
See “HP-UX 11i v2 Foundation OE (FOE)” on page 163
•
Selectable Features
See “HP-UX 11i v2 Foundation OE (FOE)” on page 163
•
168
Appendix D
Software Distribution Media
HP-UX 11i v2 Software and Driver Bundle Type Definitions
HP-UX 11i v2 Software and Driver Bundle
Type Definitions
The HP-UX 11i v2 media contains all of the software and network driver
bundles for your system to run the latest version of HP-UX 11i v2.
Additional software and network driver bundles are included, which you
may choose to either select or deselect prior to install or update. HP-UX
11i v2 contains three types of bundles:
•
environment are also always-installed. Examples include the core
— “HP-UX 11i v2 Core Software Bundles” on page 170
— “HP-UX 11i v2 Always-Installed Software Bundles” on page 171
— “HP-UX 11i v2 Always-Installed Network & Mass Storage
Drivers” on page 174
•
•
Default-Installed: Software bundles that are installed by default.
You can manually deselect the bundles before you install or update
system. Examples include Mozilla and the HP-UX Web Server Suite
bundles. For a detailed list of default-installed bundles see:
Selectable: Software bundles that are not installed or updated by
default. You must manually select these bundles before you install or
update your system. Examples include Ignite-UX and security. For a
detailed list of selectable bundles see:
— “HP-UX 11i v2 Selectable Software Bundles” on page 177
Appendix D
169
Software Distribution Media
HP-UX 11i v2 Core Software Bundles
HP-UX 11i v2 Core Software Bundles
The following software bundles comprise the base software installed for
all operating environments:
Table D-2
HP-UX 11i v2 Core Software Bundles
Bundle Name
Description
HPUXBaseOS
HPUXBaseAux
HP-UX Base OS installation bundle(64-bit)
HP-UX Base Auxiliary bundle: Additional OS
software (shown with bundle tag):
HP-UX
Kernel Configuration (Casey)
EMS Framework (B7609BA)
ONC (ONCplus)
SWGETTOOLS (SWGETTOOLS)
HP-UX Peripheral Device Tool (PeriphDev)
Software Distributor (SD)
Update UX (UPDATE-UX)
CDE-xxx
Common Desktop Environment bundle (xxx is
language variable)
170
Appendix D
Software Distribution Media
HP-UX 11i v2 Always-Installed Software Bundles
HP-UX 11i v2 Always-Installed Software
Bundles
In addition to the core software bundles installed in Table D-2, the
following software bundles are installed by operating environment (for
the latest version information, please see the Read Before Installing or
Updating to HP-UX 11i v2 DVD booklet):
The operating environments are represented as follows:
FOE
Foundation Operating Environment
EOE
Enterprise Operating Environment
MCOE
MTOE
TCOE
Mission Critical Operating Environment
Minimum Technical Operating Environment
Technical Computing Operating Environment
Table D-3
Description
HP-UX 11i v2 Always-Installed Software Bundles (by OE)
Bundle
B6836AA
FOE
EOE
MCOE
MTOE
TCOE
3D Graphics
X
X
Development Kit and
RuntimeEnvironment
(RTE) for OpenGL
Cluster Object
Manager
B8324BA
T1909BA
X
X
Enterprise Cluster
Master (ECM) Toolkit
GlancePlus Pak
B3701AA
B5736DA
X
X
X
X
High Availability
(HA) Monitors
HP CIFS Client
HP CIFS Server
B8724AA
B8725AA
X
X
X
X
X
X
X
X
Appendix D
171
Software Distribution Media
HP-UX 11i v2 Always-Installed Software Bundles
Table D-3
Description
HP-UX 11i v2 Always-Installed Software Bundles (by OE)
Bundle
B6061AA
FOE
EOE
MCOE
MTOE
TCOE
HP MLIB
X
Mathematical
Software Library
HP WBEM Services
for HP-UX
B8465BA
B9073BA
X
X
X
X
X
X
X
X
X
X
Instant Capacity on
Demand (iCOD)
Java 2 JPI v1.4
T1458AA
T1455AA
T1868AA
T1869AA
T1905BA
B5140BA
X
X
X
X
X
X
X
X
X
X
Java JPI v1.3
Java3D for JRE v1.3
Java3D for JRE v1.4
MC/ServiceGuard
X
X
MC/ServiceGuard
NFS Toolkit
Message Passing
Interface (MPI)
B6060BA
X
MirrorDisk/UX
B2491BA
NPar
X
X
X
X
X
X
nPartition Provider
X
X
X
X
X
X
Online Diagnostics:
EMS Hardware
Monitors & Support
Tool Bundles
OnlineDiag
PAM Kerberos
J5849AA
B3835DA
X
X
X
X
X
X
X
Process Resource
Manager
Technical System
Configuration
TechSysConf
X
172
Appendix D
Software Distribution Media
HP-UX 11i v2 Always-Installed Software Bundles
Table D-3
Description
HP-UX 11i v2 Always-Installed Software Bundles (by OE)
Bundle
B3929DA
FOE
EOE
MCOE
MTOE
TCOE
Veritas File Systems
(VxFS v3.5)/
X
X
OnlineJFS v3.5
Veritas Volume
Manager (VxVM) v3.5
Base-VXVM
B8843CA
T1302AA
X
X
X
X
X
X
X
Workload Manager
(WLM)
Workload Manager
Toolkits
Appendix D
173
Software Distribution Media
HP-UX 11i v2 Always-Installed Network & Mass Storage Drivers
HP-UX 11i v2 Always-Installed Network &
Mass Storage Drivers
The following drivers are always-installed on your system (all operating
environments):
Table D-4
HP-UX 11i v2 Always-Installed Network
Drivers
Contents /
Description
Supported IO
Driver
Adapters
A3739B
PCI FDDI
FDDI-00
A6795A
A5158A
FibreChannel
Tachlite
FibrChanl-00
A4926A
PCI GigEther
1000B-SX
GigEther-01
GigEther-01
GigEther-01
A4929A
PCI GigEther
1000B-T
A6825A
A6847A
A6794A
A6865A
PCI Gigabit Ethernet
(NextGen)
A6825A
A6847A
PCI IEther
(10/100BT)
IEther-00
A5506A
A5230A
Core IO 10/100B-TX
Drivers in
Built-in (Core IO)
10/100B-TX support
HPUXBaseOSbundle
A5838A
A5149A
A5150A
A6828A
A6829A
Core IO SCSI Drivers
in HPUXBaseOS
bundle
Built-in (Core IO)
SCSI support
174
Appendix D
Software Distribution Media
HP-UX 11i v2 Default-Installed Software Bundles
HP-UX 11i v2 Default-Installed Software
Bundles
The following software bundles are installed on all operating
environments by default. You can deselect any of these bundles before
you install or update your system.
Table D-5
HP-UX 11i v2 Default-Installed Software
Bundles (all OEs)
Description
Bundle Name
B6849AA
HP-UX Bastille Security Tool
GTK+ Libraries
B6848BA
Sec00Tools
B9901AA
Judy
Install-Time Security Infrastructure
HP-UX IPFilter
Judy Libraries
Mozilla Application Suite
Mozilla Source Distribution
MySQL
MOZILLA
MOZILLAsrc
MySQL
Netscape 7.0
B6835AA
ParMgr
Partition Manager
Perl 5.8 Programming Language
HP-UX Secure Shell
perl
T1471AA
B6834AA
B8339BA
Security Patch Check
Servicecontrol Manager
HP-UX Web Server Suite
HP-UX Apache-based Web Server
HP-UX Tomcat-based Servlet Engine
hpuxwsApache
hpuxwsTomcat
Appendix D
175
Software Distribution Media
HP-UX 11i v2 Default-Installed Software Bundles
Table D-5
HP-UX 11i v2 Default-Installed Software
Bundles (all OEs) (Continued)
Description
HP-UX Webmin-based Admin
Bundle Name
hpuxwsWebmin
HP-UX XML Web Server Tools
Java Bundles
hpuxwsXml
Java 2 SDK v1.3
B9788AA
B9789AA
T1456AA
T1457AA
Java 2 JRE v1.3
Java 2 JDK v1.4
Java 2 JRE v1.4
176
Appendix D
Software Distribution Media
HP-UX 11i v2 Selectable Software Bundles
HP-UX 11i v2 Selectable Software Bundles
The following bundles are not installed or updated by default. You must
select the desired bundles prior to installing or updating your system.
Table D-6
HP-UX 11i v2 Selectable Software Bundles (all
OEs)
Description
Bundle Name
HP-UX Installation Utilities (Ignite-UX) B5725AA
HP-UX Host Intrusion Detection System J5083AA
(HIDS) (Servers Only)
Java (Out of Box) Tunable
Pay Per Use
JAVAOOB
T2351AA
Security Level 10
Sec10Host
Sec20MngDMZ
Sec30DMZ
Security Level 20
Security Level 30
Software Package Builder (SPB)
SwPkgBuilder
Appendix D
177
Software Distribution Media
HP-UX 11i v2 Selectable Network Drivers
HP-UX 11i v2 Selectable Network Drivers
The following network drivers are not installed or updated by default.
You must select the desired bundles prior to installing or updating your
system.
Table D-7
HP-UX 11i v1 Selectable Network Drivers
Supported IO
Bundle Name
Adapters
Description
A5513A
A6386A
ATM (PCI)
ATM-00
PCI HyperFabric II
MUX (PCI)
HyperFab-00
TermIO-00
A6748A
A6749A
A5783A
Token Ring (PCI)
TokenRing-00
178
Appendix D
E
Web Resources
This appendix lists the many resources on the web:
•
Latest HP-UX 11i v2 information:
http://docs.hp.com/hpux/os/11iv2
http://forums.itrc.hp.com
http://www.hp.com
Local-language user guides:
http://docs.hp.com
Use the navigation menu to select a language.
Latest Itanium-based server and workstation information:
http://www.hp.com/products1/unix/operating/choice/hpux_itanium.html
Latest information on HP-UX software releases:
http://www.software.hp.com/RELEASES-MEDIA
•
•
•
•
Latest versions of HP-UX 11i v2 documentation, including release
notes, guides, and white papers:
http://docs.hp.com/hpux/os/11iv2
Downloading HP-UX patches and patch information from the HP IT
Resource Center web:
http://itrc.hp.com
Under Maintenance and Support, select the appropriate patching
tools. To receive HP Security Bulletins, select “subscribe to security
bulletins & patch digests.
•
International information:
http://www.hp.com
Select a country or region if you are not automatically directed.
High-availability products:
•
•
http://docs.hp.com/hpux/ha
HP-UX Software Transition Kit:
http://devresource.hp.com/STK
Appendix E
179
Web Resources
•
•
•
•
•
•
•
HP Technical Documentation feedback form:
http://docs.hp.com/assistance/feedback.html
Ignite-UX information and download:
http://software.hp.com/products/IUX
Partition Manager
http://www.software.hp.com/products/PARMGR
Safety and ergonomic information:
http://www.hp.com/ergo
Servicecontrol Manager:
http://software.hp.com/products/SCMGR
Software Distributor:
http://software.hp.com/products/SD_AT_HP
System administration for HP-UX systems:
http://docs.hp.com/hpux/os/11iv2
http://forums.itrc.hp.com
•
All HP-specific documentation included in the HP Apache-based Web
Server software you can find online after installation:
http://yourserver.com/hp_apache_docs
Or you can find it in the /opt/apache/hp_apache_docs/directory.
The latest information for the HP Apache-based Web Server is at the
following web site:
http://www.hp.com/go/webserver
180
Appendix E
Symbols
before you begin
installing, 80
updating, 94
/etc, 75
/etc/passwd, 90
/home, 90
/local, 91
bundles
/opt, 75, 91
/usr, 91
/usr/local/, 75
A
cache
about this guide, 5
adding
buffer, 141, 155, 158
choosing file system, 86
CIFS
OE, 105
adding groups, 138
adding patches, 129
adding users, 138
additional software, 87
alternate install methods, 81
Always-Installed
CIFS/9000
Drivers
FibreChanl-00, 174
GigEther-01, 174
Software
GlancePlus Pak, 171
HA Monitors, 171
MC/ServiceGuard, 172
MirrorDisk/UX, 172
commands
MLIB, 172
MPI, 172
Workload Manager, 173
Workload Manager Toolkit, 173
always-installed
drivers, 169
network drivers, 174
software, 169
swinstall, 95, 97
swlist, 64
software bundles, 171
Apache-based Web Server, 153, 180
applications, 120, 125, 128, 131
configuring after update, 108, 109
update-ux, 93, 97, 99, 100, 101, 104
comments, 4
Common Desktop Environment, 170
configuration, 75, 88
OE Applications, 108, 109
configuring, 138
B
backup, 72, 73, 135
system, 137
181
Index
considerations
cold-install, 38
golden images, 39
instant ignition, 38
software depots, 39
console, 66, 68
downloading, 180
console notes, 69
copyright notice, 2
core software
dump devices
bundles, 170
HPUXBase64, 170
CDE, 170
troubleshooting, 150
DVD
HPUXBase32, 170
HPUXBaseAux, 170
create depot, 99
D
EFI, 66
data collection, 142, 143
Deciding a Method
update, 37
enhancements, 21
enterprise operating environment
deciding a method
cold-install, 36
default gateway, 142
Default-Installed
Software
environments
Mozilla, 175
error codes
errors, 145
Perl, 175
examples
default-installed
drivers, 169
update using Interactive Software
Selection, 106
software, 169, 175
dependencies
security, 44
update-ux, 103
depots
updating 11i v2 OE, 104
upgrading OE, 105
creating, 99
diagnostics
offline, 71
directories, 90
F
disk space, 55
factory ignited, 32
disk volume, 87
factory ignition, 52, 81
182
fbackup, 72
Selection, 106
features, 18, 21
unavailable, 23
HP Apache
feedback, 180
feedback form, 4
FibrChanl-00, 174
file partitions, 54
file sizes, 53
Tomcat, 175
XML Web Server Tools, 176
file system metadata
firmware
HP-UX 11i
HP-UX 11i v2
recommendations, 58
flowchart
cold-install
FOE, 25, 26
considerations, 38
deciding which method, 36
DVD, 24
forums, 180
Foundation OE, 104
foundation operating environment
contents, 163
frecover, 72, 90
FW, 58
G
GigEther-01, 174
GlancePlus Pak, 171
global tunables
Minimal Computing Operating
Environment, 25
VxFS, 156
Gnome GTK+, 175
golden images, 81
installing from, 39
guide, contents, 20
Release Notes, 24
Environment, 25
H
update
HA Monitors, 171
hardware failures, 70
HIDS
deciding when, 37
HP-UX 11iv2
troubleshooting, 147
hints, 55
HP-UX Welcome Page, 28
host IP, 142
HPUXBaseAux, 170
How To
HSC
update using interactive Software
Selection, 106
how to
HyperFabric
D/R, 178
HyperFabric L/N, 178
HyperFab-00, 178
install, 83
update, 99
183
Index
I
identifying model, 60
identifying OE, 60
identifying OS, 60
identifying software, 60
IDS 9000, 177
rebuilding, 64
180
information, 27, 179
install
log files
known problems, 145
problems, 146
verify, 117, 118
install information, 90
installation tips, 131
installing, 79, 83, 84, 86
installing from
maintaining, 140
instant ignition, 38
software depot, 39
installing OnlineDiag, 70
installing patches, 128
installing software, 132
install-time
security, 43
security settings, 45, 47, 48
Instant Ignition, 81
interactive mode
kit, 24
interface differences, 68
deciding a method, 36
from previous HP-UX releases, 33
Minimal Computing Operating
ioscan, 100, 101, 132
IRTC, 140
Itanium-based
server, 179
contents, 166
Itanium-based systems, 18
Mission Critical Operating Environment, 25
mission critical operating environment
contents, 166
J
ja_JP.utf8
troubleshooting, 152
Java
Mission Critical Support, 26
mission critical support, 81
mk_kernel, 64
Out-of-Box, 177
JAVAOOB, 177
MLIB, 172
184
Index
Mod_perl, 153
model, 60
MCOE, 104
monitoring update, 97
Mozilla, 175
Source, 175
Minimal Computing Operating
Environment, 25
MP, 58, 66, 68
MPI, 172
25
MTOE, 25, 26, 53, 104
contents, 166
TCOE, 104
N
Netscape
network depot, 99
network depots
operating envronments
networking, 138
new patches, 128
new root, 90
OS patches, 128
overview
next steps, 123
NFS, 138
updating, 95
NIS, 142
notes, 69, 145
nslookup, 142
O
OEs
adding, 105
Enterprise OE, 104
Foundation OE, 104
MCOE, 104
MTOE, 104
TCOE, 104
PDHC, 58
updating, 93
offline diagnostics, 71
old patches, 128
older HP-UX Releases
migrating to HP-UX 11i v2, 33
OnlineDiag, 70
planning, 55
post-installation tasks, 90
pre-defined security, 43
pre-installed, 32
previous patches, 128
printers, 139
operating
environments, 162
operating environments, 25, 26, 53, 60
adding, 105
problems
185
Index
install, 146
Sec10Host, 43
update, 146
Sec20MngDMZ, 43
Sec30DMZ, 43
secured
process, 81
update, 95
protocols, 45
protocols
secured, 45
publication history, 4
install-time
R
settings, 45, 47, 48
Selectable
Read Before Installing or Updating to HP-UX
11i v2 DVD booklet, 24
rebuild kernel, 64
recovering files, 90
recovery, 72
Drivers
Software
selectable
release
contents, 21
identifiers, 19, 20
media, 24
names, 19, 20
selectable software
Release Notes, 28
release notes, 179
releases, 179
removing patches, 129
required media, 81
requirements, 53
restoring /local, 91
restoring /opt, 91
services
reviewing cold-install, 81
root, 87, 90, 143
secured, 45
settings
root disk, 86
root volume, 87
rx2600, 67, 68
rx5670, 67, 68
sizes
always-installed, 169, 171
bundles, 175
S
safety, 180
sam, 75, 99
saving configuration files, 75
SCM, 180
core bundles, 170
default-installed, 169, 175
media, 161
script, 97
SCSI, 57
record versions, 64
SD, 180
186
selectable, 169, 177
software depot, 95
installing from, 39
Software Selection
software transition kit, 179
source media, 76
tunables
STK, 179
storage, 57
subnet, 142
support, 26, 180
swagent.log, 121
swap, 143
swap space, 86
swconfig, 121
swremove, 53, 121
unsupported
system
update
backup, 73
Deciding a Method, 37
error codes, 97
examples
configuring, 137
firmware, 58
selectable software, 106
T
tables, 142, 143
tail, 97
contents, 168
Technical Computing Operating
Environment, 25
technical computing operating environment
contents, 168
tips, 131
problems, 146
updating, 97
steps
tools, 127
create network depot, 99
installing update-ux, 100
using update-ux, 101
tips, 64, 97
trademark notices, 3
transition kit, 179
troubleshooting, 145
CIFS, 146
187
Index
clean log files, 64
configuration, 108, 109
monitor process, 97
rebuild kernel, 64
to an 11i v2 OE, 104
to HP-UX 11i, 101
troubleshooting, 97
vs. cold-install, 36
update process
flowchart, 96
monitoring, 97
command syntax, 101
error codes, 97
errors, 97
examples, 103
from network depot, 105
installing, 100
update 11i v2 OE, 104
using, 101
updating
V
VenMsg, 66, 68
verifying, 120
VGA, 66, 68
volboot file
VUE, 75
vx_bc_bufhwm, 155
vx_ninode, 155
VxFS, 87, 143
global tunables, 156
memory use, 155
tunables, 156
VxVM, 87, 138, 143
188
|