QuickSpecs
Overview
HP SFP+ Transceivers (SR, LRM, LR and ER)
Models
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X132 10G SFP+ LC ER Transceiver
J9150A
J9151A
J9152A
J9153A
DA - 13285 Worldwide — Version 3 — September 5, 2012
Page 1
QuickSpecs
Technical Specifications
HP SFP+ Transceivers (SR, LRM, LR and ER)
HP X132 10G SFP+ LC LR Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-LR); Duplex: full only
Transceiver (J9151A)
Connectivity
Connector type
Wavelength
LC
1310 nm
A 10-Gigabit transceiver in
SFP+ form-factor that
supports the 10-Gigabit LR
standard, providing 10-
Gigabit connectivity up to
10 km on single-mode
fiber.
Physical characteristics Dimensions
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
Weight
0.04 lb. (.02 kg)
Transceiver form factor SFP+
Operating temperature 32°F to 158°F (0°C to 70°C)
Environment
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
0.9 W
Electrical characteristics Power consumption
typical
Power consumption
maximum
1 W
Cabling
Cable type:
Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and
ISO/IEC 793-2 Type B1;
Maximum distance:
2m-10km with 9/125 µm single-mode cable
Cable length
Fiber type
2m to 10km
Single Mode
Notes
Conditioning patch cord cables are not supported.
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Services
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13285 Worldwide — Version 3 — September 5, 2012
Page 3
QuickSpecs
Technical Specifications
HP SFP+ Transceivers (SR, LRM, LR and ER)
HP X132 10G SFP+ LC LRM Ports
1 LC 10-GbE port (IEEE 802.3aq Type 10Gbase-LRM); Duplex: full only
Transceiver (J9152A)
Connectivity
Connector type
Wavelength
LC
1310 nm
A 10-Gigabit transceiver in
SFP+ form-factor that
supports the 10-Gigabit
LRM standard, for 10-
Gigabit connectivity up to
220 m on legacy
Physical characteristics Dimensions
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
Weight
0.04 lb. (.02 kg)
Transceiver form factor SFP+
Operating temperature 32°F to 158°F (0°C to 70°C)
Environment
multimode fiber.
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
0.7 W
Electrical characteristics Power consumption
typical
Power consumption
maximum
1 W
Cabling
Cable type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively (a mode conditioning patch cord may be needed
in some multimode fiber installations);
Maximum distance:
0.5-220m with 62.5 µm multimode cable @ 160/500 MHz*km
0.5-220m with 62.5 µm multimode cable @ 200/500 MHz*km
0.5-100m with 50 µm multimode cable @ 400/400 MHz*km
0.5-220m with 50 µm multimode cable @ 500/500 MHz*km
0.5-220m with 50 µm multimode cable @ 1500/500 MHz*km
Cable length
Fiber type
0.5m to 220m
Multi Mode
Notes
For OM3 cable (50 µm multimode @ 1500/500 MHz*km), a mode-conditioning
patch cord is not required. Other multimode cables may require mode-
conditioning patch cords to achieve the maximum distances listed above.
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Services
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13285 Worldwide — Version 3 — September 5, 2012
Page 4
QuickSpecs
Technical Specifications
HP SFP+ Transceivers (SR, LRM, LR and ER)
HP X132 10G SFP+ LC ER Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-ER); Duplex: full only
Transceiver (J9153A)
Connectivity
Connector type
Wavelength
LC
1550 nm
The SFP+ ER Transceiver
will transmit 10Gbps over
up to 40km using standard
OM3 fiber cable. This
Physical characteristics Dimensions
2.22(d) x 0.55(w) x 0.47(h) in. (5.65 x 1.39 x 1.19
cm)
Weight
.04 lb., Fully loaded
product expands the HP
Networking transceiver
portfolio for connections
from 0m to 40km. Use only
genuine HP transceivers
with your HP Networking
equipment to ensure
Transceiver form factor SFP+
Operating temperature 32°F to 158°F (0°C to 70°C)
Environment
Operating relative
humidity
5% to 95%, noncondensing
-40°F to 185°F (-40°C to 85°C)
5% to 95%, noncondensing
Nonoperating/Storage
temperature
reliability and support.
Nonoperating/Storage
relative humidity
Altitude
up to 10,000 ft. (3 km)
1.3 W
Electrical characteristics Power consumption
typical
Power consumption
maximum
1.5 W
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
40km
Fiber type
Single Mode
Notes
Check switch release notes for minimum version of software required to
support this transceiver.
Some switches have limits as to how many of this particular transceiver can
be installed. See the release notes of the switch software/firmware being
used for more details.
Services
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
© Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and
services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
DA - 13285 Worldwide — Version 3 — September 5, 2012
Page 5
|