HP Hewlett Packard Welder storage works User Manual

MSL6000  
Series  
Drive Module  
Installation  
HP  
StorageWorks  
Caution: Parts can be damaged by  
Note: This part is not hot-pluggable.  
Before installing the drive, you must take it  
off line using the library GUI touch screen.  
electrostatic discharge. Keep parts in their  
containers until needed. Ensure you are  
properly grounded when touching static-  
sensitive components.  
Note: If you are adding an additional  
tape drive to your library, skip to  
“Installation” in step 7.  
Note: Depending on the model, your  
library may look different from the ones  
illustrated in this procedure.  
Decimal Keypad  
Touch an Input Box to Edit  
Removal  
1
2
1
4
7
2
5
8
0
3
6
9
Source:  
Drive  
1
Destination:  
Slot  
2
Element Type  
Clear  
entry  
Back  
space  
Mail  
Slot  
Drive  
Slot  
Execute  
Move  
Back  
Drive 1  
Drive 0  
Drive 1  
Drive 0  
Drive 3  
Drive 2  
Unload any tape cartridges in the drive to be  
removed using your application software or the  
library GUI touch screen.  
Inspect the contents of the kit.  
 
9
10  
Slowly insert the new tape drive into the drive  
bay, aligning the connectors on the tape drive  
with the connectors in the drive bay.  
Using a flat-blade screwdriver, tighten the two  
captive thumbscrews. If adding an additional drive,  
configure the library for the new tape drive. Refer  
to the tape library user guide for more information.  
Caution: Push on the tape drive handle  
and the bottom portion of the tape drive  
until it is seated.  
Two-Drive Library  
Four-Drive Library  
- Terminator  
- 0.5 m cable  
11  
1
2
3
- 0.5 m cable  
to host  
If you are  
- RS-232 diagnostic  
cable (for service  
only)  
4
adding an  
additional tape  
drive to your  
library, or if you  
are upgrading an existing drive, ensure you  
use supported cabling configurations. See the  
HP StorageWorks MSL6000 Series Tape Library  
User Guide for more information. The user  
guide can be downloaded from  
Note: For optimum  
performance, Ultrium  
460 and 960 drives  
should be configured  
with one drive per bus.  
12  
13  
Activate the tape  
drive by selecting  
Activate Drive n >  
Back > Back >  
Back to the main  
screen. The screen  
will change to  
indicate that drive  
n is now activated.  
Use HP StorageWorks Library and Tape Tools,  
Remote Management Interface (RMI), or MSLUtil  
diagnostic software to upgrade the drive to the  
latest firmware.  
Note: You may need to reconfigure your  
software application. Drive serial numbers  
might be used for configuration and to  
assign drives to the library.  
 
Getting Help  
• HP Product Information Site:  
• HP Technical Support and Phone Numbers:  
• HP StorageWorks Library and Tape Tools  
(L&TT) diagnostic software:  
Note: Use L&TT, RMI, or MSLUtil  
diagnostic software to verify installations  
and to ensure your library has the latest  
firmware.  
© 2005 Hewlett-Packard Development Company, L.P.  
Second Edition (March 2005)  
Part Number: 331764-002  
*331764-002*  
331764-002  
 

Haier Washer 0030808445 User Manual
Hamilton Sundstrand Company Flat Panel Television SD 2006 02 User Manual
Harbor Freight Tools Drill 7528 User Manual
Harbor Freight Tools Dust Collector 45378 User Manual
HP Hewlett Packard Flat Panel Television HP SL4282N User Manual
HP Hewlett Packard Smoke Alarm HP 11722A User Manual
Huffy Board Games M731324 User Manual
Husqvarna Chainsaw 225LD User Manual
Husqvarna Sewing Machine ER10 User Manual
Impex Home Gym PWR 6 User Manual