15"17"20"LCD TV
USER'S MANUAL
MODEL:
L15SV6-A0, L17LV6-A1,L20AV6-A0
L17L6A-G1,L20L6A,L15G1-A0,
L17G1-A0,L20G1-A0,L15D2-A0,
L17D2-A0
Please read this manual carefully before
using your television and keep this manual
In a good place for future reference.
Safety Notice Items
Incorrect usage will cause fire or electric shock. To prevent this, please do
as required when you are installing, using and cleaning this machine. To insure
your safety and extend the life-span of LCD-TV, please read the following items
carefully before using:
l Please read and understand all the instructions before operation;
l Please keep the book for later use;
l Please comply with the warning instructions on the machine and in this book
strictly;
l Please comply with the instructions provided;
l Please do not use additional devices that are not recommended by
manufacturer:
l Before operation, please make sure that the operating voltage of your unit is
normal;
l Do not placethe unit onunstable, dusty andhumid places;
l Never put theunit in directsunlight or nearheat sources;
l Allow enough space for proper ventilation;
l Please keep water away from the LCD-TV . If water comes in contact with the
LCD-TV, disconnect the power cord from the power source, then wipe the set
with a dry soft cloth;
l Do not remove the back cover. If services were need, please refer to qualified
Personnel
Main Functions
1-Can be connected with analog RGB input
2-Can be connected with CVBS,S-VIDEO , and SCART (CVBS/RGB)
input
3-Can receive TV signal
Front Panel Controls
7
6
7
6
5
1
2
3
4
5
1
2
3
4
6
6
7
MENU
PR
VOL
TV/AV
1
3
5 7
2
4
3
2
4
G1 series
1
D2 series
1
4
2
3
5
4
2
3
5
TV/AV MENU VOL- VOL+ CH-
CH+ POWER
TV/AV MENU VOL- VOL+ CH-
CH+ POWER
7
6
7
6
Note: These buttons are onthe top ofthe sets onthese two series.
Control Panel Function
1. MENU Press to select the main menu
2.
VOL (V-/VOL-) Volume down /Left orientation toadjust the itemin the OSD
VOL (V+/VOL+) Volume up / Right orientationto adjust theitem/Press to
enter the submenu.
3. PR (P-/CH-)
TV channel down / to select the item in the menu
TV channel up / to select the item in the menu
Select the inputsignals: SCART/PC-RGB/AV/S-VIDEO/TV
PR
4.TV/AV
(P+/CH+)
5. Power supplyswitch
6. Power indicator
Illuminates red in standby mode, illuminates green when the display is
turned on
7.Remote Sensor
Receivingremote control sendsthe infrared remote
signal.
Connection Options
The figure is just for referrence, please see the real.)
AV Audio Input
D-SUB Input
Connect audio/video
output from an external
device to these jacks
SCART Input
Connect to the D-SUB
15PIN analog output
connector of the PC
display card for PC
display purpose
Connect to the DVD/
VCR/broadcasting
receiver or other
equipment
Earphone port
L
R
DC IN
D-SUB IN
HEADPHONE PC AUDIO IN
SCART
S-VIDEO VIDEO
AUDIO
ANT
S-Video Input
PC Audio Input
Connect S-Video out
from an S-Video device
to the jacks.
Connect the PC output
connector from a PC to
the audio input port
Antenna Input
Connect cable or
antenna signals to
the TV, either direc-
tly or through your
cable box.
DC Power Cord Socket
This TV operates on DC power.
The voltage is indicated on the
Specifications page . Never
attempt to operate the TV on AC
power.
Remote Control Key Functions
When using the remote control, aim it towards the remote sensor on the TV
SLEEP DISPLAY MUTE POWER
NICAM
PC
AUTO AD TV/AV
PSM
OK
.SSM
Q.VIEW
P+
V-
MENU
V+
P-
INDEX
TEXT
SUBCODE MIX
TIME
HOLD
SIZE
REVEAL
Illustration of the keys on the remote control:
POWER
1.
Power supply switch
MUTE
2. MUTE
3. DISPLAY
4. 0-9
Display current input signal information
TV channel number select
Set time to change the TV into the standby status after a
period of preset time.(time is 240/180/120/90/60/45/30/15/0)
5. SLEEP
NICAM/A2 Stereo select
EXIT
6. NICAM
7. OK
Quick TV channel switch(return to the last channel)
8.Q.VIEW
9. V-
Volume down / Left orientation to adjust the item in the OSD
Volume up / Right orientation to adjust the item/Press to
enter the submenu.
V+
TV channel up/down or select the item of the menu
Select SCART/PC-RGB/AV/S-VIDEO/TV
10. P+/P-
11. TV/AV
12. PSM
Select picture mode: PERSONAL/STANDARD/MILD/FRESH
Remote Control Key Functions
PC-RGB system select
13. PC
M
Select sound mode:VOICE/MUSIC/THEATRE/PERSONAL
Auto adjust (PC mode)
14. SS
28. AUTO AD
15. RED
Correspond to the differently colored subjects
16. CYAN
17. GREEN
T
E
L
E
T
E
X
T
18.YELLOW
19. TEXT
Switch to the Teletext with text mode/turn off Teletext and
switch to TV mode
Hold on or off for current page display
Switch to the Teletext with mix mode
20. HOLD
21. MIX
Request index page
Change display size
22.INDEX
23.SIZE
Sub coded page access
24.SUBCODE
25.TIME
While in normal TV mode only, pressing the button TIME will
display the teletext time in the top right corner for a few
seconds.
Reveal or hidden the hidden words
Press to select the main menu
26.REVEAL
27. MENU
Note:
The buttons instructionfor the operationjust take remotecontroller for examplein this
manual . Buttons(MENU , V+/-or VOL or VOL+/-, P+/-or PR orCH+/-,
TV/AV,POWER or )on the TV panel iscorresponding with buttons( MENU, V+/-, P+/- ,
TV/AV , POWER )on the remotecontroller.
Installing Batteries
1.Slide open thecover of thebattery compartment onthe back ofthe remote
control.
2.Load two 5#alkaline batteries inthe compartment. (plusand minus polesto
respective mark)
3.Replace the coverof the batterycompartment.
1
2
3
Connection Instructions
Grounding
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connectingit to telephone wires, lighteningrods, or gaspipes.
External Equipment Connections
Antenna Connection
- Antenna or Cable Service with a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
wall antenna
socket
RF coaxial wire (75 ohm)
VHF antenna
UHF antenna
Be careful not to bend the bronze
wire when connecting the antenna.
outdoor
antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
To improve picture quality in a poor
signal area, purchase and install a
signal amplifier.
If the antenna needs to be split for two
TV s, install a 2-Way Signal Splitter
in the connections.
If the antenna is not installed properly,
contact your dealer for assistance.
NOTE: All cables shown are not included with the TV
Connection Instructions
PC Setup
You can use your LCD-TV as a monitor for your personal computer using a VGA
cable (not supplied).
Connection and use steps:
1.Read the userguide supplied with
your computer and ensure that it has
a VGAconnector;
2.Make sure that the power of the LCD
-TV and thePC are off;
3.Connect a Dtype 15-pin VGAinterface
cable ( not supplied ) to the VGAvideo
interface connector on the PC. Then
connect the other end to the VGA video
interface connector on the back of the
LCD-TV.Tighten the screwson the VGA
connectors once they are firmly
connected;
4.Turn on the power ofthe LCD-TV first,
and then turn on the power of the PC;
5.Press the TV/AV button to set the video
input mode ofthe LCD-TV toPC-RGB;
6.Check the image on your TV. There may be noise associated with the resolution,
vertical pattern, contrast or brightness in PC mode. If noise is present, change
the PC mode to another resolution, change the refresh rate to another rate or
adjust the brightness and contrast on the menu until the picture is clear. If the
refresh rate of the PC graphic card can not be changed,change the PC graphic
card or consult the manufacturer of the PC graphic card.
Connection Instructions
VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the
VCR and TV
Connection and use steps:
1.Read the user guide supplied with your AV devices and ensure that it has
Composite or S-Video connectors;
2.Make sure that the power of the LCD-TV and the AV device are off;
Connection Option 1
Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.
Connection Option 2
1. Connect the audio and video cables from
the VCR's output jacks to the TV input jacks,
as shown in the figure.
When connecting the TV to VCR, match
the jack colors (Video = yellow,Audio
Left = white,and Audio Right = red).
If you connect an S-VIDEO output from
2
VCR to the S-VIDEO input, the picture
quality is improved; compared to conne-
1
.
cting a regular VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner
manual.)
s
VCR
3.Turn on the power of the LCD-TV first ;
and then turn on the power of the AV
device;
4.Press the TV/AV button to set the video
input mode of the LCD-TV to S-VIDEO
mode or AV mode.
Connection Instructions
Cable TV Setup
- After subscribing to a cable TV service from a local provider you can watch cable
TV programming. The TV cannot display TV programming unless a TV tuner
device or cableTV converter box is connectedto the TV.
- For furtherinformation regarding cableTV service, contact your localcable TV
service provider(s).
Connection Option 1
1. Select 3or 4 withchannel switch oncable
box.
2. Tunethe TV channel to thesame selected
output channel oncable box.
3. Select channelsat the cablebox or with
the cable boxremote control.
Connection Option 2
1. Connect theaudio and videocables from
the Cable Box'soutput jacks tothe TV
input jacks, asshown in thefigure.When
connecting the TV to aCable Box, match
the jack colors
(Video = yellow, Audio Left =white, and
Audio Right= red).
2. Select theinput source byusing the TV/AV
button on theremote control.
3. Select yourdesired channel withthe
remote control forcable box.
External AV Source Setup
How to connect
Connect the audioand video cablesfrom
the external equipment'soutput jacks tothe
TV input jacks, as shown inthe figure.
When connecting theTV to external equip-
ment, match thejack colors (Video = yellow,
Audio Left =white, andAudio Right =red).
How to use
1. Select theinput source byusing the TV/AV
button on theremote control.
2. Operate thecorresponding external equi-
pment. Refer toexternal equipment ope-
rating guide.
Basic Operating Instructions
Turn on the LCD-TV
When the POWER button is pressed and the LCD-TV is
SLEEP DISPLAY MUTE POWER
NICAM
PC
AUTO AD TV/AV
turned on, the indicator light on the front of the LCD-TV
changes from red to green. When the LCD-TV is turned on,
the input mode is displayed on the screen. When the LCD-TV
is turned off using the power button, the LCD-TV will go into
standby mode and the indicator light turns red.
PSM
OK
.SSM
Q.VIEW
P+
Note:
The display of the input mode
will disappear in3 seconds.
TV
V-
MENU
V+
P-
SCART
INDEX
TEXT
SUBCODE MIX
PC-RGB
AV
TIME
HOLD
SIZE
REVEAL
S-VIDEO
Switch Among Different Inputs: TV / SCART / PC-RGB / AV / S-VIDEO
Press the TV/AV button to select the input mode you want.
Each time you press the TV/AV button, TV, SCART , PC-RGB, AV, S-
VIDEO, will appear on the screen in the order.
.
Note:
The display of the input mode will disappear in 3 seconds.
Audio Control
1.Press the V+ button to increase the volume. A number will appear on
screen indicating the volume level.
2.Press the V- button to decrease the volume. A number will appear on
screen indicating the volume level.
Mute
1.Press the MUTE button to mute the sound temporarily. A mute icon
appears on the screen.
2.Press the MUTE button or V+ again to restore the sound.
The mute icon disappears.
Note: when you cut off the power supply completeley , the mute function is
cancelled automatically . But if the TV is switched to standby mode , the
mute function can not be cancelled.
When you press MUTE to cancel the sound ,if you press V- button , the
level of the sound will be decreased, but the sound is still mute. In this
condition,when you press MUTE again, the sound will restore the level you
have decrease just.
Basic Operating Instructions
Select the TV Channel You Want
You can use the number keys on the remote control to directly select TV
channels.
The LCD-TV can store up to 100 channels , and you can press the keys on the
remote control or on the panel to make a selection.
1.Press the relevant key on the remote control if you want to choose any channel
from 0 to 9. for example: if you want to choose channel 8, just press the key
number 0 and 8.
Note: You must press 0 first and then the other numbers from 0 to 9 if you want
To choose channels from 0 to 9)
2.If you want to choose a channel bigger than 9, please enter the two digits of the
channel number you want to watch within 3 seconds. for example: select
channel 16
Picture Mode
Press PSM button on the remote control for menu display . For desired mode as
follows:
PERSONAL STANDARD MILD FRESH
TELETEXT
Some menu related function are not available in TELETEXT mode. MENU and AUTO AD
control functions are not available in TELETEXT mode. If the TV is switched on by POWER
after off in TELETEXT mode, or press TV/AV or PC button, the TELETEXT mode will
disappear automatically.
Teletext features may vary depending on the Broadcasting
Companies and is only available if the channel selected is
SLEEP DISPLAY MUTE POWER
NICAM
PC
AUTO AD TV/AV
transmitting Teletext. Pressing the TEXT button whilst in
Teletext operation will switch the current status to TV.
When in Teletext mode, the volume may still be altered to
the desired listening level.
PSM
OK
.SSM
Q.VIEW
P+
V-
MENU
V+
Page Selection
P-
INDEX
TEXT
Pages can beselected in twoways:
a. Press P+ or P- button to increase or decrease the
page number by one.
SUBCODE MIX
TIME
HOLD
SIZE
REVEAL
b. By entering the page number, using the number
keys on the remote control.
SIZE Button
Press SIZE button to change display size : normal large top large bottom
normal
REVEAL Button
Press REVEAL to reveal hidden words e.g. Quiz page answers . Press again
to hide.
Red/Green/ Yellow/CyanButtons
These four buttonscorrespond to thedifferently colored subjects .
HOLD Button
Press HOLD button to remain the Teletext page when viewing multi-page
information .
INDEX Button
Press INDEX button to return to the main index page .
Depending on the way information is transmitted , this may have to be pressed
more than once to return to the main index page .
TELETEXT
SUBCODE Button
When Teletext information exceeds more than one page , it may take some time
for the automatic changing of the sub pages to reach the sub page you require .
It is possible to enter your required sub page and continue watching the normal
programme until the correct sub page is found .
Select the required page number using buttons 0-9 .
If the top of the page indicates that sub pages are being transmitted yet the page
does not change . Then the number at the top of the page is there to indicated
that the broadcaster has updated the page s contents , there are no sub pages .
Press SUBCODE button , page number/--- will be displayed at the bottom right
of the screen.
Enter desired sub page number before the page number/--- disappears . To
select page 6 enter 0,0,0 and 6 .
TEXT Button
Press TEXT to enter Teletext mode and only the text page can be visible .
MIX Button
Press MIX button to enter Teletext mode and both the TV picture and text page
can be visible.
TIME
While in normal TV mode only, pressing the button TIME will display the
teletext time in the top right corner for a few seconds.
Menu Operations
* In this manual, the OSD (On Screen Display) may be different from your TV
because it is just an example to help you with the TV operation.
s
1. Press MENU button to either display the PC MENU or
TV MENU or
VIDEO MENU or GENERAL MENU or AUDIO MENU in different
source inputs.
2. Press P+/P- to scroll through the parameters
3. Press V+/V- buttons to make changes to the parameters
4. Press the OK button to exit the menu
Picture Menu Options
Picture quality can be adjusted for any input separately .
The picture qualityon the screencan be adjustedas follows:
1. Press MENU button until the following menu appears on the screen.
PC MENU
PC MENU
BRIGHTNESS
CONTRAST
50
50
COLOR SETTING 9300K
AUTO CONFIG
H-POSITION
V-POSITION
PHASE
50
50
50
50
CLOCK
AV/S-VIDEO MENU
VIDEO MENU
BRIGHTNESS
CONTRAST
COLOR
HUE
SHARPNESS
50
50
50
50
50
Menu Operations
Picture Menu Options Continued
TV MENU
VIDEO MENU
BRIGHTNESS
CONTRAST
COLOR
HUE
SHARPNESS
50
50
50
50
50
2. Press P+/P- button to enter the picture menu and to go up and down to
select the desired option .
3.Press V+/V- button to increase and decrease the level to adjust the
selected option to your preference .
4. Repeat step 2 and step 3 until desired picture quality has been achieved .
Function:
BRIGHTNESS :Adjust the brightness of the picture . By increasing the level, it
will add more light to dark parts of the picture and by decreasing the level ,it will
add more dark to light parts of the picture.
CONTRAST : Adjust the contrast of the picture . The image becomes higher as
the number increase.
COLOR SETTING : Press V+/V- to select between 9300K/6500K/USER
define . You could adjust the color values in USER mode . And the menu display
as follows:
USER COLOR SETTING
RED
GREEN
BLUE
100
100
100
AUTO CONFIG : Is opted for adjustment of picture location frequency and phase
parameters .
H-POSITION : Picture horizontal adjust
V-POSITION : Picture vertical position adjust .
Menu Operations
Picture Menu Options Continued
PHASE : Removes any horizontal distortion and clears or sharpness the displayed
characters .
CLOCK :Adjust the TFT-LCD tomatch the PC-RGBinput source
COLOR : Press V+/V- to adjust the color
HUE :Adjust the toneof the picture. Appearand be adjustedonly under NTSC
mode
SHARPNESS : Adjust the amount of the detail enhancement , the image
sharpness rises as the number increases (By increasing the level, it will show
cleaner and clearerimages and bydecreasing the level, it will makepicture
smoother).
Sound Menu Options
Sound can be adjusted for any input as follows:
1. Press MENU button until the following menu appears on the screen
AUDIO MENU
VOLUME
BALANCE
50
50
AUDIO PRESET PERSONAL
TREBLE
BASS
AVL
50
50
ON
You can adjust sound options BALANCE, TREBLE, and BASS to the levels you
prefer.
2. Press P+/P- button to enter the audio menu and to go up and down to
select the desired option .
3.Press V+/V- button to increase and decrease the level to adjust the
selected option to your preference .
4. Repeat step 2 and step 3 until desired audio quality has been achieved ..
Menu Operations
Sound Menu Options Continued
Function :
VOLUME : Adjust the volume of your TV
BALANCE : Adjust the balance of the audio output from left to right . When
indication value of balance increases toward 100 , sound of the left speaker
becomes weaker . When indication value of balance decreases toward 0 ,
sound of the right speaker become weaker .
AUDIO PRESET : Press V+/V- to select between PERSONAL, VOICE,
MUSIC and THEATER .
TREBLE : Adjust the treble of the sound . Can only be adjust under PERSONAL
mode .
BASS : Adjust the bass of the sound . Can only be adjust under PERSONAL mode .
AVL: Select ON to adjust the volume level automatically.
General Menu Options
Menu Language Selection:
The menus can be shown on the screen in the selected language. First select
your language.
1. Press the MENU button until the GENERAL MENU appears on the screen .
2. Press P+/P- button to select LANGUAGE.
3. Press V+/V- button to select your desired language.
From this point on, the on-screen menus will be shown in the language of your
choice.
GENERAL MENU
LANGUAGE
ENGLISH
ON
OFF
TV
PAN EUROPEAN
EAST
BLUE SCREEN
NOISE REDUCE
INPUT SOURCE
TXT LANGUAGE
TXT EAST/WEST
RESET
Menu Operations
General Menu Options Continued
1. Press MENU button until the following menu appears on the screen
GENERAL MENU
LANGUAGE
ENGLISH
ON
OFF
TV
PAN EUROPEAN
EAST
BLUE SCREEN
NOISE REDUCE
INPUT SOURCE
TXT LANGUAGE
TXT EAST/WEST
RESET
You can adjust sound options BLUE SCREEN , NOISE REDUCE, INPUT
SOURCE and RESET to the levels you prefer.
2. Press P+/P- button to enter the general menu and to go up and down to
select the desired option .
3.Press V+/V- button to adjust the selected option to your preference .
4. Repeat step 2 and step 3 until desired quality has been achieved ..
Functions:
1. BLUE SCREEN : You can set it ON or OFF . If select ON and there is no signal ,
the screen will display blue screen
2.NOISE REDUCE : select OFF/LOW/MID/HIGH to reduce the noise of the
picture , provide clearer picture . (The effect is more and more distinctness if
you select in sequence as follows: OFF, LOW, MID,HIGH.)
3. INPUT SOURCE : Display current mode . There are PC-RGB , AV , S-VIDEO ,
TV , SCART to display .
4. TXT LANGUAGE: To switch the teletext languages.
5. TXT EAST/WEST: To select EASTor WEST .
6. RESET : Press V+ to reset some settings to the factory default .
Menu Operations
TV Menu Options
1. Press MENU button until the following menu appears on the screen
TV MENU
CHANNEL
SYSTEM
SKIP
AFC
FINE TUNE
SWAP
1
DK
OFF
ON
448.25MHz
MANUAL SEARCH
AUTO SEARCH
Note: This menuis only appearsin TV mode.
2. Press P+/P- button to enter the TV menu and to go up and down to
select the desired option .
3.Press V+/V- button to adjust the selected option to your preference .
4. Repeat step 2 and step 3 until desired picture quality has been achieved ..
Functions:
1. CHANNEL : Press V+/V- to change the TV channel .
2.SYSTEM : Select the TV standard system from DK,I,L,BG
3. SKIP : If you want skip a channel , press V+/V- to select ON , and this
channel will be skip next time when you press P+/P- . But you can press
digits button to select the channel . If you want to restore the channel , select
OFF.
4. AFC : Auto frequence control . Select ON to improve the image quality .
5. FINE TUNE : If the image received is not very good , you can press P+/P-
to select FINE TURN item in menu . Then , press V+/V- button to adjust
and improve the image quality .
Menu Operations
TV Menu Options Continued
6. SWAP : Press V+ to display the menu as follows:
FROM :
TO :
1
9
SWAP
Press P+/- to select the item and then V+/- to adjust the channel and V+
to confirm.( For example: press P+/- to select FROM item, and then press
V+/- to adjust the channel number to 1; then Press P+/- to select TO item,
and V+/- to adjust the channel number to 9; press P+/- to select SWAP item,
and then V+ to confirm. The two channels will be exchanged)
7. MANUAL SEARCH : Press V+ to start to search the channel . The following
menu will display on the screen:
DOWN
543.25MHz
UP
Press P+/- or V+/- to select DOWN or UP , and then press MENU to confirm.
(If you select DOWN, the search will search the lower frequency channel and UP
will search the higher frequency channel)
7. AUTO SEARCH : Auto search and save the channel .press V+ to start to
search the channel and the following menu will appears on the screen :
AUTO SEARCH
SECAM L
NO
YES
Press P+/- to select SECAM L , and V+/- to adjust between SECAM L and
BG/DK/I system.
Press P+/- to select NO or YES, and MENU to confirm. Then the TV will start
to search as follows:
AUTO SEARCH
PLEASE WAIT
11
190.65MHz
You could press MENU to stop the search .
Specifications
Specifications of the television that you have just purchased may
vary from the information in this table due to technical innovations.
Picture, sound
PAL/SECAM-B/G,I,D/K,L,L
system
Antenna input
impedance
75
Audio output
1.5W+1.5W
AV input PC input S-VIDEO input PC audio input
SCART input 12V DC input Antenna input
External input port
Input: ~100-240V 50/60Hz,
Output:
--- 12V
AC-DC adapter
Temperature
Working:5 C~35 C
Storage:-15 C~45 C
NOTE:Sound system L' certainly does not demonstrate in the TV's OSD, in
menu L includes sound system L and sound system L'.
Accessories
1
2
AC-DC adapter
AC cable
3
4
Remote control
Owner's Manual
5 Batteries
Warranty card
6
Note Warranty card is only forthe special countriesand areas
Note:
All specifications are subject to change without notice.
All quality are approximate value.
V0.2
0090506259
|