Installation
Domestic Dishwasher
DW9-AFE
Diagram
The symbol
on the product or on its packaging indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and elec-
tronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative con-
sequences for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product.
GB
For more detailed information about recycling of this product, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.
Code:0120505667
Detergent and Rinse Aid
S a l t
Salt
Adjusting Salt Consumption
Detergent
Rinse Aid
The hardness of the water varies from place to place. If hard
water is used in the dishwasher, deposits will form on the dishes
and utensils.
The dishwasher is designed to allow for adjusting the amount of
salt consumed based on the hardness of the water used. This is
intended to optimise and customise the level of salt consumption
so that it remains at a minimum. Your local Water Board can
supply the degree of hardness of the water in your area.
To adjust salt consumption, proceed as follows:
Detergent specifically intended for use with dishwashers must
be used. The dispenser must be refilled before the start of each
wash cycle following the instructions provided in the "Wash Cycle
Table." The detergent dispenser is located on the inside panel of
the door.
This product makes dishes sparkle and helps them to dry with-
out spotting. The dispenser is located on the inside panel of the
door and should be filled after every 80 wash cycles (or when
the rinse aid indicator light comes on for those models with this
feature).
The appliance is equipped with a special softener that uses a salt
specifically designed to eliminate lime and minerals from the water.
Loading the Salt into the Softener
Loading the detergent
Loading the Rinse Aid
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should
be filled as follows:
To open the "A" cover on the dispenser, press the "B" button.
The detergent for the wash cycle should be poured into the "C"
compartment.
To open the dispenser, turn the "C" cap in an anti-clockwise
direction and then pour in the rinse aid, making sure not to overfill.
The amount of rinse aid used for each cycle can be regulated by
turning the "F" dose adjustor, located beneath the "C" cap, with
a screwdriver. There are 6 different settings; the normal dosage
setting is 3.
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
After the detergent has been placed in the dispenser, close the
cover and press down until it clicks in place.
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel (supplied) into the hole and intro-
duce about 2 kg of salt. It is normal for a small amount of water
to come out of the salt container.
Important
B
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs, the
dosage adjustor should be turned to a higher setting.
If the dishes have white streaks, turn the dosage adjustor to a
lower setting.
- Carefully screw the cap back on.
- Unscrew the cap from the salt container;
- There is a ring on the container with an arrow on it (see figure),
If necessary, rotate the ring in an anticlockwise direction from
the "-" setting towards the "+" sign, based on the hardness of
the water being used.
It is recommended that adjustments be made in accordance with
the following scheme:
Water Hardness
C
A
C
Salt
Autonomy
Selector
Clarke
consumption
(Grams/cycle)
ºdH
Level
mmol/l
(cycles/2kg)
position
degrees
Note: To facilitate closing the cover, remove any excess de-
tergent on the edges of the dispenser.
1
2
0
14
0 17
0 1,7
/
0
/
The salt container must be filled when the "low salt" indicator
light (located on the control panel) comes on.
F
14 36 18 44 1,8 4,4
"-"
20
60
To prevent the formation of rust, load the salt just before begin-
ning a wash cycle.
3
4
36 71 45 89 4,5 8,9 MED
40
60
40
25
>71
>89
>8,9
"+"
.4.
.3.
GB
GB
Turning on the Appliance
Loading the Dishwasher
Before placing the dishes in the dishwasher, remove larger food
particles to prevent the filter from becoming clogged, which results
in reduced performance.
Starting a wash cycle
Setting the Wash Cycle with a Delayed Start Time
Lower Rack
Upper Rack
After having completed all of the installation steps in the preced-
ing paragraphs, turn on the water all the way and press the ON-
OFF button (D) located on the control panel. The "A" indicator
light will come on. At this point, the appliance is on but you must
wait a few seconds before programming the cycle setting.
By pressing the "F" button (see close-up view-'Control panel")
the start of wash cycle can be delayed for between 1 to 12 hours.
Each time the button is pressed, the display (G) will show the
number of hours for the delay period. Choose the amount of
time desired. After selecting the wash cycle, a short acoustic sig-
nal will sound and after a few seconds, the delay time on the dis-
play will blink, This indicates that the countdown has begun.
If the pots and pans have baked-on food that is extremely hard to
remove, we recommend that they are soaked before washed. This
will eliminate the need for extra wash cycles.
Pull out the rack to load the dishwasher.
Setting and Starting a wash Cycle
Select the desired cycle by pressing the selector button (I). Each
time the button is pressed, one of the "J" cycle indicator lights will
come on in succession. Choose the wash cycle you feel is most
appropriate for the type of dishes that need washing (consult the
wash cycle table contained in this manual. After a few seconds,
the wash cycle has begun and can no longer be changed.
How to use the lower rack
We recommend that you place the most difficult to clean items on
the bottom rack: pots, pans, lids, serving dishes and bowls, as
shown in the figure to the right.
After the time has lapsed, the cycle will start.
Load for 9 Standard Settings
It is preferable to place serving dishes and lids on the sides of the
racks in order to avoid blocking the rotation of the top spray arm.
- Pots, serving bowls, etc. must always be placed face down.
- Deep pots should be slanted to allow the water to flow out.
- The lower rack features fold down tine rows (see fig.A) so that
larger or more pots and pans can be loaded.
NOTE:
During the delay period, it is preferable not to change any of the
settings, If this is necessary, all of the settings must be cancelled
by pressing the ON/OFF button (D).
1
Cancelling or modifying a cycle
2
At this point, all of the steps for "setting the wash cycle with a
Delayed Start Time" and "Setting and Starting a wash cycle" must
be repeated, following the instructions contained in the correspond-
ing sections.
A cycle that is underway can only be modified if it has only been
running for a short time. Otherwise, the detergent may have al-
ready been used, and the appliance may have already drained
the wash water. If this is the case, the detergent dispenser must
be refilled (see the paragraph entitled, "Loading the Detergent").
To modify a cycle that is already underway, press the ON/OFF
button (D), all of the settings will be cancelled. To set a new
cycle, follow the instructions contained in the paragraph entitled
"Setting and starting a wash cycle".
- The silverware basket can not be doubled (see fig.B).
- Silverware should be placed in the silverware basket with the
handles at the bottom; if the rack has side baskets, the spoons
should be located individually into the appropriate slots. Espe-
cially long utensils should be placed in the horizontal position at
the front of the upper rack.
3
4
If the door is opened to the unit during the delay period, the count-
down will stop. It will begin again when the door is closed.
All of the wash cycle set to reverse time function, we may in
fig.B
fig.A
focus start circulate time.
How to use the upper rack
The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, cups and saucers, plates, small bowls
and shallow pans (as long as they are not too dirty).
- Position the dishes and cookware so that they do not get moved
by the spray of water.
Wash Cycle adjustment Buttons
1/2 load Button
Wash Cycle Program Light
The dishwasher is equipped with a LED indicator light (J) that
turns on when the appliance is running the wash cycle.
Adjust the upper basket to the higher level and you have more
space to accommodate those taller pans and trays in the bottom
basket.
This button (see "close-up View - Control Panel", letter"E") makes
it possible to wash dishes using only the upper rack if there are
not enough dishes for a full load. This will allow you to save on
water and power. It can be used before setting any of the wash
cycle, except for the intensive cycle ( if included in the wash cycle
table). Please keep in mind that the amount of detergent should
also be cut in half.
fig.C
At the end of the wash cycle
Six beeps will indicate that the wash cycle has finished and the
cycle indicator light (J) for the cycle will begin to die out. Turn off
the appliance using the ON-OFF button. Turn off the water sup-
ply to the appliance and open the door. Wait a few minutes be-
fore unloading the dishwasher to avoid handling the dishes and
utensils while they are still hot and more susceptible to breakage.
They will also dry better.
Shelf
Lean tall glasses and those with long stems against the shelf-not
against other items to be washed.
Place glasses, cups and small bowls on the additional cup rack.
The additional cup rack can be swivelled in or out as required(see
fig.C).
.6.
.5.
GB
GB
Wash Cycle Table
Energy Saving Tips
- Use the right amount of detergent: if you use too much detergent,
the result will not be cleaner dishes, but, rather, a greater nega-
tive impact on the environment.
- It is important to try and run the dishwasher when it is fully
loaded in order to save on energy. To prevent odors from forming
and food from caking onto the dishes, you can run the soak cycle.
Cycle Selection
Cycle
Description of Cycle
Detergent Rinse Aid
Information
- Choose the right wash cycle: the choice of cycle depends on
the type of dishware, cookware and utensils being washed and
how dirty they are.
Pre-wash with warm water.
Very dirty dishes, pots and
pans. (not to be used with
delicate items)
Extended wash at 70ꢀ
.
Rinse with cold water.
Rinse with hot water.
Drying.
30g
Heavy Duty
Pre-wash with cold water.
Normal dirty dishes, pots
and pans. standard daily
cycle.
Extended wash at 55 ꢀ
.
30g
15g
Rinse with cold water.
Rinse with hot water.
Drying.
Normal Wash
Rapid Wash
Economic, fast cycle to be
used on not very dirty dishes
right after they are used. No
drying cycle.
Short wash at 40
Cold rinse .
.
ꢀ
How to Keep Your Dishwasher in Shape
After Every Wash
Moving the Appliance
Pre-wash with cold water.
Extended wash at 48ꢀ.
Rinse with cold water.
Rinse with hot water.
Economic,test cycle for
IECEN50242
After every wash, turn off the water supply to the appliance and
leave the door slightly ajar so that moisture and odors are not
trapped inside.
If the appliance must be moved, try to keep it in the vertical position.
If absolutely necessary, it can be positioned on its back.
5+25g
(5)
Glass ware
(EN50242)
Seals
Remove the Plug
One of the factors that cause odors to form in the dishwasher is
food that remains trapped in the seals. Periodic cleaning with a
sponge will prevent this from occurring.
Pre-wash of dishes, pots and
pans while waiting for the load
to be completed after the sub-
sequent meal.
Short cold wash to prevent food
residue from drying on the dishes .
Before cleaning or performing maintenance, always remove the
plug from the socket.
Soak
No Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do not
use solvents or abrasive cleaning products. Use only a cloth and
warm soapy water.
When You Go on Holiday
When you go on holiday, it is recommended that you run a wash
cycle with the dishwasher empty and then remove the plug from
the socket. Turn off the water supply and leave the door of the
appliance slightly ajar. This will help the seals last longer and pre-
vent odors from forming within the appliance.
To remove spots or stains from the surface of the interior, use a
cloth damp and a little white vinegar, or a cleaning product made
specifically for dishwashers.
.8.
.7.
GB
GB
Installation
Cleaning and Special Maintenance
Positioning the Appliance
The connection must be made to the hot water line following the
same procedures as those for the connection to the cold water
line.
Position the appliance in the desired location. The back should
rest against the wall behind it, and the sides, along the adjacent
cabinets or wall. The dishwasher is equipped with water supply
and drain hoses that can be positioned to the right or the left to
allow proper installation.
Filter Assembly
Cleaning the Spray Arms
For best performance and results, the filter assembly must be
cleaned.
It may happen that food particles become encrusted on the
sprayer arms and block the holes (see "Close up view interior",
letters C-E ). Check the sprayer arms periodically and clean them
when needed.
Anti-Flooding Protection
The filter efficiently removes food particles from the wash water,
allowing it to be recirculated during the cycle. For this reason, it
is a good idea to remove the larger food particles trapped in the
filter after each wash cycle by rinsing the "A" semi-circular filter
and cup under running water. To remove the filter assembly, pull
on the cup handle in the upward direction. The entire filter as-
sembly (made up of the "A" semicircular filter and the "B" fine
filter) should be cleaned at; east once a month. To clean the filter
and the fine filter, use a cleaning brush. Then, reassemble the
filter parts as shown in the figures below and reinsert the entire
assembly in the dishwasher, positioning in its seat and pressing
downward.
The dishwasher is equipped with a system that stops the supply of
water in the event of a problem with the water supply hose, or
leaks within the unit, If for any reason the box containing the elec-
trical components happens to get damaged, remove the plug from
the socket immediately. In order to guarantee that the anti-flood-
ing feature operates properly, the "A" box with water supply hose
must be attached to the water supply tap as shown in Fig.1. No
other type of connection is acceptable. The water supply hose must
not, under any circumstances, be cut, as it contains electrical parts
which are live. If the length of the hose is not adequate to make a
proper connection, the hose must be replaced with one that is long
enough. This hose is available upon request from specialised re-
tailers and service centres.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing them
in or out) to adjust the dishwasher, making it level. In any case,
the appliance should not be inclined more than 2 . If the appli-
ance is level, it will help ensure proper performance.
A
Cold Water Connection
B
fig.1
Connect the cold water supply hose to a threaded 3/4 (gas) con-
nector making sure that it is fastened tightly in place (see Fig.1).
If the water pipes are new or have not been used for an extended
period of time, let the water run to make sure that the water is
clear and free of impurities. If this precaution is not taken, there is
a risk that the water inlet can get blocked and damage the
appliance.
Cleaning the Water Inlet Filter
Periodically clean the water inlet filter (see fig.1/A) located on
the outlet of the water supply tap.
The dishwasher must never be used without the filters. Improper
replacement of the filters may reduce the performance level of
the appliance and damage dishes and utensils.
After turning off the water tap, unscrew the end of the water sup-
ply hose, remove the filter and clean it carefully under running
water. Then, return the filter to its place and tighten the water
supply hose back into position.
Hot Water Connection
The water supply to the appliance can also be connected to the
house's hot water line (centralised system, heating system), as
Troubleshooting
long as it does not exceed a temperature of 60
.
In this case, the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
Fig.1
It may occur that the dishwasher does not function or does not
function properly. Before calling for assistance, See what can
be done first: Have you forgotten to press one of the buttons or
to perform an essential operation?
The dishwasher does not drain
Attention:
Have you checked whether:
The appliance is to be connected to the water mains using new
hose-sets and old hose-sets should not be reused!
- the drain hose is crimped or bend.
Lime deposits or a white film form on the dishes
Have you checked whether:
Installation
The dishwasher does not start
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
Attention:
Drain Hose Connection
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
If, despite all these checks, the dishwasher still does not function
and/or the problem persists, contact the nearest authorised service
centre and provide them with the following information:
- the nature of the problem;
The special plastic hose support must be solidly fastened to the
wall to prevent the drain hose from moving and allowing water to
spill outside the drain.
Insert the drain hose into a drain pipe with a minimum diameter
of 4cm, or let it run into the sink, making sure to avoid bending
or crimping it. Use the special plastic support that comes with
the appliance (see Fig.2). The free end of the hose must be at
a height between 40 and 100 cm and must not be immersed in
water.
- the ON-OFF switch is on "ON";
- the water supply is turned on.
Electrical Connection
- the model and the serial number which are indicated on the plate
located on the side of the inner part of the door.
After making sure that the voltage and frequency values for the
current in the home correspond to those on the rating plate (located
on the stainless steel inner door of the appliance) and that the
electrical system is sized for the maximum voltage on the rating
plate, insert the plug into an electrical socket which is earthed prop-
erly (the earthing of the appliance is a safety requirement man-
dated by law).
Never call on unauthorised technicians and refuse to allow
parts to be installed that are not original spare parts.
The dishwasher does not load water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient pressure;
- the water supply hose is crimped or bend;
- the filter for the water supply hose is clogged.
If the electrical socket to which the appliance must be connected is
not appropriate for the plug, replace the plug rather than using
adapters or the like as they could cause overheating and burns.
Fig.2
.10.
.9.
GB
GB
|