User's manual
Fully Automatic Washing Machine
This manual is for
HWM6815
Please read this manual
carefully before using.
Retain it for future reference.
Names of the parts
Top lidI
Water valve
Sop mat
Top lid II
Cabinet handle
Drain hose
Detergent box
(two)
Lint filter
Control panel
Power cord
Filter cover
Inner tub
Control panel
film
Pulsator
ack cover
fixed foot (3)
Cabinet
Adjustable foot
ase frame
Meaning and description of the symbols
Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety
of the user.
Warning sign
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
of the machine or injure the personal safety of the user.
Forbidden sign
1
Safety precautions
The power cord plug should be convenient
Please plug the plug on special receptacle
with rated voltage. Be sure to use single-
phase three pins receptacle. Ensure the
earthing prong of the power receptacle is
earthed reliably. Use leakage protector if
possible.
to be pluged in or pluged out with hand
while the washing machine runs normally.
Be sure to pull the plug out and close the
water tap when the machine is idle, when
moving the machine, or when cleaning
the machine. Do not use wet hand to insert
or pull out the power plug.
Do not damage the power cord, bend ,extend, twist, bind or alter it by force. Do not press or
nip it with weight. If the power cord or the power plug is bad, or the power plug becomes
flexible, to avoid risk it is required to have it replaced by
the technicians of our special shop or the after-sale
service department. Keep the pin of the power plug
clean, if the power plug is polluted with dust, please
wipe with dry cloth carefully.
Do not use water hotter above 50 C .
Do not put the machine at damp place like
the bathroom. Never wash it with water.
Not put wet laundries on the control panel.
In case the washing machine is installed
on ground with carpet, do not block the
ventilation hole with carpet.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
The ventilation holes
at the bottom
soft items
Do not let the machine share one receptacle with other
electric appliances. If the power plug is damaged, or
the plugging into the receptacle is loose,
do not use the plug any more.
2
Safety precautions
Do not stretch hands into the working
Do not decompose, repair or alter the
machine by yourself.
machine. It is dangerous even if the
rotation is slow. Take special care of
the children. Do not let the children
climb the washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
r
Petrol
Thinne
The handicapped or children without
care shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the heater.
Toprotect your laundries and wash-
ing machine, please take out all of the
coins, buttons, sand, hairpin and
To prevent the lint inside the tub from blocking
the cascade outlet during washing, please
keep the lint filter in good condition, and
other foreign materials before washing.
install it to proper position. If the lint filter
is lost or damaged, please contact the local
after-sales service department of our company.
Please check if the water faucet is open,
and if the connection of the water inlet
pipe is proper.
Install
Dismantle
Install
Caution: :Do not connect to the hot water supply
Dismantle
It is suggested to use foamless washing
powder.
3
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
Install the bottom plate
Install the lint filter
After you open the package, please lean the
washing machine gently down on soft items
( like the towel cloth, blanket, etc. ). Install the
bottom plate to the bottom of the machine with
the five screws by a cross screwdriver, then
lift the machine up gently. See to the figure:
Push the lint filter
downward to location
for lint filter.
Back
Front
Soft items
Bottom plate
Screw
Adjust the installation position
The largest allowed slope of the
shank base of the machine is 2
.
The slanting or rough ground will
result in unstable running or
stoppage of the machine. Please
adjust it with following methods:
Adjust the adjustable foot:
1.To twist the adjustable foot, please
first lift up the side of the foot slightly,
loosen the adjustable nut, and twist
the foot.
adjustable nut
Fasten
adjustable foot
Loosen
High
Low
2.Fasten the nut after adjustment.
4
How to change the direction of the drain hose
1.Loosen the fastening screw of the
back cover to take off the back cover.
Be careful not to do it by force to
prevent breaking the claw of the back
cover.(as indicated in Figure 1)
3.Extend the drain hose from the installation
hole at the right side of the base frame. Fix
the drain hose onto the base frame with the
drain hose frame and fasten the screw. Then
set the drain hose hook on the drain hose and
hang the drain hose on the hanging hole of
the cabinet. (As
Back cover
indicated in Figure 3)
Figure 1
Figure 3
2.Take off the drain hose from the cabinet.
Nip the drain hose outlet slightly.
Dismantle the drain hose hook. Loosen
the fixing screw of the drain hose frame
to dismantle the drain hose frame. Pull
the drain hose into the cabinet from the
4.To install the back cover, first hang the lower
beard of the back cover on the cabinet, then
push the claws at the two side and the upper
end from bottom to top to resume the original
setting. Be careful not to do
left side of the base frame.
Drain hose frame
it by force. Then fasten
the screw (two points)
(as indicated in Figure 4).
Topclaw
Screw
Claws at the
two sides
Lower bread
Figure 4
Figure 2
Nip the drain hose outlet
Screw
and take off the drain hose hook
Usage of the drain hose
The drain hoseshall drain smoothly
1.The height of the drain hose shall be
less than 10cm, or the drainage will not
be smooth, and cost such long time that
the machine may stop at mid way.
4.If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
2.Do not trample or press the drain hose.
<10cm
If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
5.If the extrahose is toolong, cut it
either at A or at B point.
5
Install the water inlet hose
Confirm the water tap
Water tap,not suitable
Water tap,suitable
Outlet end surface
>10mm
It is required that the frontend shall be longer than 10mm.
The outlet end surface of thetap shall be flat and smooth. If not please file it to
avoid leakage.
Connection between the water inlet hose jointer and
the water tap
1.Press the lower end of the lock lever and push down the slider. Take off the water
inlet hose jointer from the water inlet hose component. See to Figure 1.
2.Loosen the screw till the water tap can be accessed. Put the jointer of the water
inlet hose on the tap. See to Figure 2. (If the tap diameter is too large and the jointer
can not be set on the water tap, please loosen the four screws and take out the
bushing in the jointer. See to the figure3.)
Water inlet pipe jointer
Screw
Slider
Mark label
Screwdriver
bushing
Locking lever
Water inlet pipe
Figure 1
Figure 2
Figure 3
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure.
See to Figure 5.
Remarks: Before twisting the fastening nut, the thread is 4mm above the
upper surface of the nut. After twisting the fastening nut, the thread is 2mm
above the upper surface of the nut. See to Figure 6.
About 4mm before twisting
About below 2mm after twisting
Nut
Figure 4
Figure 5
Figure 6
6
Connection between the water inlet hose and the
washing machine
1.Do not takeoff the water absorption
cushion. Please checkif the cushion
is dropped ordamaged before each
usage. If ithappens please contact
our after-sale departmentimmediately.
2.Put the nutof the waterinlet hose on
the valve jointer.
Nut of the water inlet hose
3.Fasten the nut. Swaying it gentlyto
confirm if it'ssuitable.
Water absorption cushion
Jointer of thewater inlet valve
Note : The new hose- set supplied with appliance are to be used and the old hose-sets should not be reuse.
Connection between the jointer of the water inlet
hose and the water inlet hose
1.Push down theslider. Insertthe
water inlet hoseinto the jointer.
Jointer of thewater
inlet hose
Slider
Locking lever
2.Hang the locklever to thejointer.
Release the slidertill a click
sound is heard.
Check the connection between the jointer of the
water inlet hose and the water tap
1.Swaying the hosegently to confirmif it isfastened stable.
2.After installation, openthe tap tocheck if itleaks.
3.Do not bendthe hose withoverstrain.
4.Before each usageplease check if
the connection betweenthe jointer
of the waterinlet hose andthe water
tap, and theinstallation of the
water inlet hoseare firm, soas to
prevent dropping fromimproper
Installation position.
Take down the water inlet hose
1.Close the watertap.
2.Press the lockinglever. Pushdown the slider. Then
pull off the water inlethose. If themachine is used
more than onceevery week, thejointer of thewater
inlet hose canbe kept onthe tap toprevent
damaging the fixingscrew.
Locking lever
Slider
7
Preparation before washing
Preparation before washing
1.Connect the water inlet hose and open the
water tap .
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth ter-
minal to the gas pipe and tap water pipe.
3.Put down the drain hose.
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to followings before washing the laundries
Confirm
if
Clear the pocket. Fasten the The quantity of
When the pulsator
the laundries is running , the
shall not exceed buttons of the
the rated value. laundries may
The big laundries cause noise. For
there's special Take out the
requirement for coins , sand,
the laundries. hairpins etc.
buttons and
zippers.
like the jeans
shall be put in
loosely.
t h e s a k e o f
discretion, please
put the laundries
with buttons into
other laundries.
a. Please check if the laundries are applicable for washing.
b. Separate those not colorfast from other laundries.
c. For laundries not water absorbing, please put them into water with hands.
d. For laundries with much soil, please remove the soil first. You can add detergent on the
part with serious soil directly. It is much easier to remove the soil by that mean.
e. For laundries likely to get lint ball or with long fibre, please first turn the inside out before
putting them into the water.
f. Do not put the laundries polluted with chemicals directly into the washing machine.
For those small laundries ,laundries likely to be twisted or worn, and woolen laundries,
please put them into mesh bag before washing.
8
Put in the laundries
The capacity of washing andspinning of the
machine refer to the largestweight of the
standard laundries under dry condition that
can be washedor spinned inone time. One
time washing quantity shall be lower thanthe
rated capacity.
The thickness, size, type ofthe cloth willinf-
luence the actual washing capacity. It is sui-
table for onetime washing to put inreasona-
ble amount oflaundries and the laundries can
be turned round in washing.
To wash thin laundries like thestocking, silk
etc , pleasefirst put theminto washing mesh
bag (which canbe purchased separately)
before wash.
Usage of the detergent
How to use the washing
powder
Direct dissolved in the machine
1.Fill water to "Low" water level.
2.Add the power. Runfor 30 seconds
to dissolve it completely.
Inlet box of the detergent
3.Put in thelaundries. Select
suitable water level.
How to usethe whitener
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 and a
container.
2.Add the powderwhile stirring to
fully dissolve it.
Put in the proper quantities detergent
according to the water level and the
laundries quantities .
It is suggested not to use high
sudsing detergent.
Washing powder with poor qualityor
long time storage maybe caked.
Please pay attention to cleaning the
detergent box intime
Fill water to decided level. Dilute
the whitener with container. Pour
it slowly into the washing tub.
Avoid using whitener on
laundries with color or pattern as
they are prone to lose color.
The whitener shall not touch the
laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
For powder whitener, please
dissolve it before use.
9
Use the operation buttons
a.
Description of the function of the buttons
SURPLUS(MIN)
"POWER ON/OFF"button
To indicate -- during sensing.
To indicate remaining min. During
program running.
Press "Power On/Off"button to connect
power supply.
After power is connected, pressing this
button will cut off the supply.
To indicate remaining reserved
time (hrs) during reservation period.
To indicate fault symbols for abnormal
"START/PAUSE"button
conditions (see page 15)
Page 15
After the power is switched on, press it to
start the machine
During working, push it to pause working.
During pause, push this button to restart
and continue operation.
PROGRAM
STANDARD
PROCESS
SOAK
HEAVY
WASH
RINSE
SPIN
DELICATE
QUICK WASH
WASH
SPIN
POWER
ON/OFF
START
PAUSE
PROGRAM
SET TIMER
WATER LEVEL
/SET TIMER " button
"PROGRAM
Press"PROGRAM/SET TIMER " button
you can select one or several programs of
Standard,Heavy,Delicate,Quick Wash,Wash
and Spin.
Press"PROGRAM/SET TIMER " button
" WATER LEVEL"button
The user selects a suitable water level
depending on the load.
over 2 seconds, you can select the program
of reservation. The nixie tube displays the
reserved hours to the wash cycle end. The
indicator flashes to indicate in-reservation.
Remarks: 1. After pressing "POWER ON/OFF" to connect power supply, if the washing
machine lasts idle more than 5 min, it would automatically shut off the supply.
10
b.
Operating procedure and explanations for the
buttons
PROGRAM
STANDARD
PROCESS
SOAK
HEAVY
WASH
RINSE
SPIN
DELICATE
QUICK WASH
WASH
SPIN
POWER
ON/OFF
START
PAUSE
PROGRAM
S E T T I M E R
WATER LEVEL
1 Press the "POWER ON/OFF" button to switch on
the power supply
POWER
ON/OFF
2 Press the button of" PROGRAM/SET TIMER " to
select a suitable full-automatic program
PROGRAM
SETTIMER
After switching on, the "Standard" program will be thedefault. If other full-automatic program is
desired, you can press thebutton " PROGRAM / SET TIMER " to getthe corresponding
indicator on. Refer to the"Button of "PROGRAM/SET TIMER
paragraph on page 10.
"
Page 10
Example: Use the "Quick" program for slightly soiled articles.
When "standard" programis selected, thewashing machine willperform full-automatically
controlled fuzzy programto set waterlevel, water flowand wash durationaccording to the
cloth nature andweight
If there is water inside the tub, the machine cannot detect the laundries and will display
middle level. If wet laundries are put in, it may display high level. You must set suitable
water level by yourself.
11
Attention
Even there's no water in the tub, the
spinning will start after a certain period.
Do not use soak process for woolen
laundries.
Wash the laundries that are prone to lose
colors separately from other laundries.
The pulsator will not rotate unless the
water is filled to selected water level.
Selection method of the procedure programs
Times of pushing
the"select"button
Contents(tthe nixie tube indicates
the programs about to run)
Selected program
Applicable procedure
0
1
2
3
4
5
Normal wash
STANDARD
HEAVY
Wash (bb) Rinse(cc) Spin(dd)
Large, thick or heavily soiled
laundry
Soak (AA) Wash (bb)
Rinse (CC) Spin (dd)
The laundry needn'tspin to
avoid wrinkles
DELICATE
QUICK WASH
Wash (bb) Rinse(cc) Spin(dd)
Wash (bb) Rinse(cc) Spin(dd)
Wash (bb)
For load below 1 kg
Repeat using thewashing
liquid
WASH
SPIN
When the laundriesneed only
spinning after manual
washing (first drainthen spin)
Spin(dd)
If you pushthe " PROGRAM/SET TIMER " button for6 times, itwill
resume the original mode, and itwill circulate like that.
If you select the"QUICK WASH" program, you have to set thefull procedure
of wash, rinse and spin. The procedure can not be selected.
12
3 Press the "WATER LEVEL" button to select suitable
water level
WATER LEVEL
After switching on the power, press the button "WATER LEVEL" to select a water level according
to the load. Please refer to the button " Water level" on page 10.
Page 10
4 Push the " PROGRAM/SET TIMER " button
to select suitable reserve program
PROGRAM
SET TIMER
After switching on, the washing machinereserved wash programwill be automaticallyset
inactive. If youdesire a washcycle to endat a reservedtime, you canpress the
"PROGRAM/SET TIMER"
button over 2seconds to seta reserved wash program.
Refer to The button of "PROGRAM/SET TIMER "
on page 10.
Page 10
Confirm the reserveprogram
When "Reservation" becomes active, thenixie tube
displays the timeto the endof the reservedwash cycle, and
the indicator turnson.During reserve procedure,pushthe
"Reservation" button to displaythe reserve mode.
To change the runningprogram or cancelthe reservation,
you should cutoff the supplyand reselect.
the washing will finish
about 18 hours later
5 Press the "start/pause" button
START
PAUSE
Close the top lid
Except water filling ,washing, rinsing and draining, if the top cover is opened, the
washing machine will stop running and alarm.
Finish washing
The washing machine cuts off the power supply automatically when wash cycle ends.
13
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
When washing, lint filter must be used
After using, please clean it in time.
Lint filter:
Clean
1.Pull upward to detach
Figure 1
2.Clean the lint
Put it in water and clean while it is still wet.
(See to Figure 1).
Dismantle
Install
Install
Dismantle
3.Press downward to assemble.
Figure 2
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol,
alcohol etc.
The filter screen of the water inlet
valve is likely to be blocked by
foreign materials andinfluence
the water inlet. Please clean it
Alcohol
Petrol
inner
Th
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
14
Trouble shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending it to
repair. If there are real breakdowns, please come to the special maintenance department or
after-sale service department of our company. Do not repair it byyourself.
The reason
How to settle
Phenomena
Buzzing upon reservation starts,
Nixie tube indicates "E0"
Close the top lid
The top lid is not closed
Put down the drain hose.
Is the drain hose put down?
Is the drain hose blocked
by foreign material?
No or slow drain, nixie tube
indicates "E1" , buzzing.
Open and close the top lid once.
Clean the foreign material.
Open and close the top lid once.
Running pauses during spin,
nixie tube indicates "E2",
buzzing
The top cover leaves open
Close the top lid
Re-order the laundries. Close the
top lid.
Level the machine in right position.
Open and close the top lid once.
Are the laundries put
slantingly?
Is the machine slanting?
Safety switch actuates, not spin,
(after self-correction twice),
nixie tube displays "E3", buzzing
Open the water tap. Push the
"Start/Pause" button.
Clean the water inlet valve.
push the "Start/Pause" button.
Wait for the normal water pre-
ssure before use.
The water tap is not open
The water inlet valve is blocked
No or slow water filling not
reaching the level in 15min
nixie tube indicates "E4",
buzzing
,
The water pressureis too low
and the currentis too small
If the nozzle is choked with
foreign bodies
Remove the foreign bodies
Poor or no waterfall flow
Not wash
Is there power failure?
Is the power plug loose?
Use it when the power is on.
Insert the power plug tightly.
Affusion to the set water level.
Does the water level arrive at the
set water level?
The machine
does not act
Insert the power plug tightly.
Close the top lid
Put the laundries orderly.
Is the power plug loose?
Is the top lid closed?
Are the laundries put orderly?
Not spin
Level the machine properly.
Re-order the laundries.
Is the machine slanting?
There's abnormal sound
inside the machine
Are the laundries slanting in
spinning?
Is the jointer screw of the water
inlet hose is loose or twisted
awry?
Fasten the jointer screw
properly.
The water faucet leaks
Common phenomena
Phenomena
Explanation
The spinning is intermittent when it starts.
Balance the laundries to avoid slanting.
The program is setting the drain time. Some time is
needed before it starts spinning.
Push the "Process" button to
select "Spin", but it doesn't work.
It is the water remained in the factory inspection of
performance.
There may be some water flowing out of
the drain hose in the first use of the machine.
While water filling in wash and rinse, the
pulsator pauses rotation
To prevent splash during water filling.
Supplementary water filling 48 s after
sensor tests cloth material.
Wash pauses
15
Packing list
Name
Quantity
One piece
User's manual
Components of the water
inlet hose
One piece
Two piece
Lint filter
Bottom plate
One piece
Tapping screws
Five pieces
One set
Fully automatic washing machine
Specification
High/About 48 L MIDDLE/About 37L
Low/About 30L EX.LOW/About 20L
Water level/Water
quantity (about)
0.03MPa-1MPa
Water inlet pressure
Rated washing/spinning capacity(kg)
6.0/6.0
16
3HK-6-414S-045-00-0
|