Fully Automatic Washing Machine
User's manual
This manual is for
HWM75-0528 A
Special number:
837A
Please read this manual
carefully before using.
Retain it for future reference.
Packing list
Names of the parts
Water inlet valve
Top lid component
Water absorption
cushion
Detergent box
Control pannel
One
One
User's manual
Warranty card
Inside the document bag
Inside the document bag
Power cord
Filter frame
Softener inlet
Handle
Balance ring
Inner tub
Components of the water inlet
hose
Drain hose
One
Inside the accessory bag
Pulsater
Front control
board
Cabinet
Fixed leg
(3 pieces)
Lint filter
Inside the document bag
One
Drain hose frame
Adjustable
leg film
Adjustable leg
Back cover
Tapping screws
Bottom plate
Eight
Inside the accessory bag
Meaning and description of the symbols
Between the upper cushion of the washing
machine package and the upper seal of the
package carton
One
One
Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety
of the user.
Warning sign
Automatic washing machine
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
of the machine or injure the personal safety of the user.
Forbidden sign
1
Trouble-shooting answer to question
Safety precautions
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not
breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
The washing machine must be positioned so that
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
the plug is accessible. Be sure to pull the plug off
and close the water faucet in following cases:
power failure, delivering the machine, setting the
machine idle or cleaning the machine. Do not plug
or pull the power plug with wet hand.
Phenomena
The reason
How to settle
Buzzing upon reservation starts,
the digitron displays "E0"
The top lid is not closed
Close the top lid
Put down the drain hose. Open
and close the top lid once.
Clean the foreign material.
Open and close the top lid once.
Is the drain hose put down?
Earth
No or slow drain, the digitron
displays "E1" , buzzing.
Is the drain hose blocked by
foreign material?
Running pauses during spin,
the digitron displays "E2",
buzzing
The top cover leaves open
Close the top lid
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or our customer care agent.
Re-order the laundries. Close the
top lid.Level the machine in right
position.
Are the laundries put slantingly?
Is the machine slanting?
Safety switch actuates, not
spin, (after self-correction
twice), the digitron displays
"E3", buzzing
Open and close the top lid once.
Open the water tap.
The water tap is not open
No or slow water filling (not
reaching the level in 40 min),
the digitron displays "E4",
buzzing
Push the "Start/Pause" button.
Clean the water inlet valve.
Push the "Start/Pause" button.
Wait for the normal water pressure
Before use.
The water inlet valve is blocked
The water pressureis too low
and the current is too small
In case the washing machine is installed on ground
with carpet, do not block the ventilation hole with
carpet.
Do not use water hotter than 50
.
Please contact the after-sales
service department.
The water level sensor is bad.
The ventilation
holes at the bottom
The digitron displays E6.
Poor or no waterfall flow
If the nozzle is choked with
foreign bodies
Remove the foreign bodies
Back
Soft object
Is there power failure?
Is the power plug loose?
Use it when the power is on.
Front
Insert the power plug tightly.
Affusion to the set water level.
Not wash
The machine does
not act
Does the water level arrive at the
set water level?
Is the power plug loose?
Is the top lid closed?
Insert the power plug tightly.
Close the top lid
Not spin
Are the laundries put orderly?
Put the laundries orderly.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Is the machine slanting?
Level the machine properly.
Re-order the laundries.
There's abnormal sound inside the
machine
Are the laundries slanting in
spinning?
Is the jointer screw of the water
inlet hose is loose or twisted
awry?
Fasten the jointer screw
properly.
The water faucet leaks
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure pauses.
The cloth sensor is detecting , it will add water
after about 48 senconds.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
The program is setting the drain time , certain
period is needed before it starts spinning.
Select spin program, but it does not work.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained performance inspection
by the factory.
2
Safety precautions
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Do not decompose, repair or alter the machine
by yourself.
Do not stretch hands into the working machine.
It is dangerous even if the rotation is slow.
Take special care of the children.
The lint filter must be used during washing.
It must be cleaned in time after each using.
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See to Figure 1)
2. Clean the lint
Put it in water and clean while it is
still wet.(See to Figure 2)
Figure 1
Do not put any hot or heavy items (such as the kettle
with hot water) on the washing machine
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the filter frame ,
then push the upper part of the
filter in ( marked with " up side ").
(See to Figure 3)
Benzene
Figure 2
Figure 3
The appliance is not instruct for use of young
children of infirm persons without supervision.
Young children should be supervised to ensure
that they do not play with the appliance.
Keep the machine away from direct sunlight and
heat source like the heater.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
The filter screen of the water inlet
valve is likely to be blocked by
foreign materials andinfluence
the water inlet. Please clean it
Do not wipe it with thinner, petrol,
alcoholetc.
hol
Alco
Thinner
Petrol
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
Installation and adjustment
Please install and adjust the machine according to the requirement of the mannual.
It is very important to your security and correct operating the machine.
3 Push the " WATER LEVEL "button,select suitable water level
Install the lint filter
Install the bottom plate
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"
button, then push the "water level" button to set the water level.
After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth,blanket, etc. ).
Install the bottom plate to the bottom of the
machine with the eight screws by a cross
screwdriver, then lift the machine up gently.
See to the figure:
1.Press downward to assemble.
2.Pull upward to detach.
4 Push the "PROGRAM/RESERVE" button to select suitable reserve
wash program
Back
After switching on the power, the reserve program is set to off mode automatically. If you need to
set the washing procedure to be finished at reserved time, please push the "PROGRAM/RESERVE"
button to set the reserve wash program two seconds. Refer to "PROGRAM/RESERVE"
button in Page 11 for selection.
Front
Bottom plate
Soft items
Screw
the washing will be finished after 18 hours.
Adjust the Installation position
5 Push the "Start/Pause" button
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
6 Finish washing
After finishing wash it will switch off power automatically
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
the adjustable nut
the adjustable leg
Fasten
Loosen
High
2 . After adjustment, fasten the nut.
Low
How to change the direction of the drain hose
Steps of using the operation buttons and
description of the steps
b
1.Dismantle the rear cover of the washing machine.
3.Dismantle the drain outlet protecting cover at the other side,
(the way is the same as the drain bushing),then install the drain
bushing, as indicated in Figure 4.
2.Put down the drain hose .Take off the drain hose
frame as indicated in Figure 1.Take the drain hose into
the cabinet ,then nip the drain fixing clamp to make it
deviated from the clip,the other hand is used to put down
the drain bushing,as indicated in Figure 2,3.
4.Extend the drain hose from the other side. Fix the drain hose
with drain hose frame onto the cabinet, as indicated in Figure 5.
Program
STANDARD
SOAK HEAVY
GENTLE
Drain outlet
protecting cover
SAVE
COTTON
SINGLE WASH
RINSE SPIN
SINGLE SPIN
TUB CLEAN
AIR DRY
INDICATION OF PROCESS
POWER
ON/OFF
TIME REMAINED(MINUTES)
(NO CHOOSING)
SOAK
WASH
RINSE
SPIN
Drain hose
WATER
LEVEL
RESERVE(HOURS LATER)
Digital display
Fuzzy logic col
Figure 5
Figure 4
START
PAUSE
10 water leve
PROGRAM/RESERVE
Drain hose support
Cabinet
Drain bushing
Figure 2
Drain bushing
Figure 1
5.Install the drain outlet protecting cover to the other side,
as indicated in Figure 6
Inner
Push
Outer
Drain bushing
Take down
Drain hose fixing
clamp
Figure 6
Figure 3
Push
1.Push "POWER"button to switch on the power
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose
with our company serviceman .
POWER
ON/OFF
2.Push "PROGRAM/RESERVE" button to select
suitable automatic program
PROGRAM/RESERVE
Usage the drain hose
The drainage shall be smooth with the drain hose.
After the power is switched on, "standard" is automatically set. To select other full-auto program, please push
the "PROGRAM/RESERVE" button till the corresponding indicator is on. Refer to the "PROGRAM/RESERVE
button" on Page 11.E.g
1.The height of the drain hose shall be less than 10cm,
or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.
4.If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
For instance:select "SAVE" program for small quantity of laundries with light soil.
2.Do not step on or press the drain hose.
Program select
The running process
(the digitron displays the running process)
Program
The display of digitron
Application
WASH(
SOAK(
)
)
SPIN(
)
STANDARD
Common washing
RINSE(
WASH(
)
)
01
02
03
SOAK HEAVY Washing for coverlet bigger laundries
SPIN(
)
RINSE(
SPIN(
SPIN(
)
GENTLE
)
)
Washing the woollen silk textiles
3. If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
WASH(
WASH(
)
RINSE(
RINSE(
)
5.If the extra hose is too long, cut it either at A or at B.
)
)
SAVE
)
Washing for normal laundries
Washing the cotton textiles
04
05
06
COTTON
WASH(
WASH(
)
)
SPIN(
)
RINSE(
SINGLE WASH
Reusing the washing detergent
Washing the cloth washedby hand
(first draining, then spinning)
RINSE(
)
RINSE SPIN
SINGLE SPIN
SPIN(
)
07
08
Only spinning the cloth wetor washed by
hand (first draining, then spinning)
SPIN(
SPIN(
)
)
The spinning time is thesame to the single spin,
but spinning in lower
TUB CLEAN
AIR DRY
09
10
Avoid growing mildew on the outer tub and the
inner tub
SPIN(
)
12
5
Install the water inlet hose
Confirm the water faucet
"Power" button
Reserve,Process,remain time digitron
Push the "power" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "power" button to switch on the power. If the
"start/pause" button is not pushed, the machine will
switch off the power automatically after 5 minutes.
Water faucet,suitable
Water faucet,not suitable
It displays "--" during detecting.
It displays remained reserve time (hour).
It displays total remained time (min). If the total time
exceeds 99 minutes, it uses "A" on tens digit to
represent100 minutes, and uses "b" to represent 110
minutes.E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation.
(See to Page15)
Outlet end surface
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
HT
LIG
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the
four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise
it may leak water. See to Figure 3.)
FLASH
(MINUTES)
POWER
ON/OFF
WATER
LEVEL
(HOURS LATER)
Digitall display
Fuzzyy logiic control
10 water level selection
PROGRAM/RESERVE
water inlet hose jointer
Screw
Slider
Sign plate
Screw knife
Bushing
Figure 3
Lock level
WATER LEVEL button
PROGRAM/RESERVE button
The washing machine can detect the laundries automatically.
After detection,it will set the water level to suitable value among
4, 6, 8,and 10 automatically.
Push down the program/ reserve button. You
can select one program of ten which is
standard,soak heavy, gentle,save,cotton,
single wash,rinse spin,single spin,tub clean,
air dry;
water inlet hose
Figure 2
Figure 1
You can also set water level by yourself. After the machine is started,
it will not set water level automatically. You shall push thestart/pause
button to make new setting.
3.Fasten the four screws evenly. See to Figure 4.
If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .
Push the"program/ reserve" button to set the
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
reserve wash program morethan two seconds
continuously;
If save program is selected, it will display water level 2 .
When water level 2 is reached in water filling, it will perform
washing while filling water.When water level 3 is reached, it will
change to normal washing.
When the "reserve" function is activated, the
indicator light of the program you have set will
be off. The "reserve (hour)" and "time remain"
indicator lights will be on;
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
During operation of wash and rinse program, you can push down
the water level button to add water. When you release the button, or
it reaches the overflow water level, the machine will stop adding
water.
About 4mm before twisting
About less than 2mm after twisting
During reserve procedure, push the "reserve"
button to display the reserve mode.To change
the running program or cancel the reserve
setting, you need to switch off the power and
make new selection;
The water level decided may be different from actual value because
of the different moisture level of the laundries.
Screw nut
Figure 5
Attention As selecting the waterlevel 1,3,5,7,9;the light
is flashing;
Figure 4
Figure 6
As selecting thewater level 2,4,6,8,10;the light
is lighting;
5 Use the operation buttons
Description of operation button
Connection between the water inlet hose and the washer
1.Do not take off the water absorption cushion. Please check if the
cushion is dropped or damaged before each usage. If it happens
please contact our after-sale department immediately.
a
nut of the water
inlet hose
Indicator mode and meaning
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
Off:
Flashing: indicate the running program
jointer of the
water inlet valve
water absorption
cushion.
On: indicate the program about to run, or
indicate the selected mode
Connection between the jointer of the water inlet hose and the water inlet hose
the jointer of the
water inlet hose
1.Push down the slider. Insert the water inlet hose into the jointer.
Slider
Program
STANDARD
Locking level
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
SOAK HEAVY
GENTLE
SAVE
COTTON
INDICATION OF PROCESS
SINGLE WASH
(NO CHOOSING)
RINSE SPIN
SOAK
TIME REMAINED
SINGLE SPIN
WASH
TUB CLEAN
AIR DRY
RINSE
SPIN
RESERVE
START
PAUSE
Check the connection between the jointer of the water inlet hose
and the water faucet
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
START/PAUSE button
After the power is switched on,press it to
start the machine
During working,push it to pause.
During pause,push this button to restart and
go on working
Dismantle the water inlet hose
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
Attention:
Locking level
If the machine is used frequently, the jointer of the water inlet hose can be
on the faucet to prevent damaging the fixing screw.
kept
Slider
1. The digitron displays the remained time and process alternately during the washing machine
working.
2. The process function is not selected solely .(see to Page 12)
1.Preparation before washing
3. Usage of the detergent
How to use the softner
Preparation before washing
1.Connect the water inlet hose
The usage and dose of the softener as per the specifications of softener.
Before washing put the softener into the filling entrance(can be found on
the balancing ring by rotating the inner tub, as illustrated in the left
drawing, The softener will put into the washer when rinsing.
After the softener is put in, please don't place for a long time otherwise
softener may solidify and cause flowing not smooth.
2.Confirm that the washing machine is earthed reliably.Then insert the
Softener
inlet
SOFTNER
power plug into the receptacle.Do not connect the earth terminal to the
gas pipe and tap water pipe.
3.Put down the drain hose.
4.Slanting or uneven ground may result
in unstable working or abnormal noise.
Please make the machine stand horizontally.
When the washer in spin process,please don't push "START/ PAUSE "
button for fear that the softener is put in earlier, which affect the effects.
Pay attention to followings before washing the laundries
Control panel seat
Add washing powder into the box directly
as per indicated in left figure.
Clear the pocket.
Take out the coins ,
sand,hairpins etc.
Confirm if there's
special requirement
for the laundries.
The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.
Fasten the buttons
and zippers.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
After adding, close the box.
Liquid detergent inlet
laundries.
How to use washing powder
It is suggested to add washing powder into the box directly
under fuzzy program and reserve program.
How to use the whitener
Dissolve directly inside the washing machine: (not applicable
for fuzzy and reserve program)
1.Add some water(select the "1" water level)
2.Add washing powder. Run for about 30s to fully dissolve
the powder. Then push the"start/pause" button.
3.Put in laundries. Select suitable water level. Push the
Fill water to decided level. Dilute
the whitener with container. Pour
it slowly into the washing tub.
Avoid using whiteneron laundries
with color or pattern as they are
prone to lose color.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries with unfast color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
button again.
"start/pause"
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into
mesh bag for washing.
Quick dissolving of washing powder:
The whitener shall not touch the
laundries directly.
Refer to theuser's manual for the
usage and quantity of the whitener.
For powder whitener, please
dissolve it before use.
1.Prepare warm water of 30 C and container.
2. Add washing powder while stirring to dissolve it completely.
Please add suitable washing powder as per the laundries
quantity, the set water level and water quantity.
If you select save program, it is suggested to use liquid
detergent instead of washing powder to guarantee the
2.Put in the laundries
washing effect.
It is not recommended to use rich-foam washing powder.
The capacity of washing of the machine refer to the largest weight of the standard
laundries under dry condition that can be washed in one time. Laundries quantity
in one washing cycle shall be lower than the rated capacity.
Washing powder with poor quality or long-time storage may
get caked. Please clean the detergent box duly in usage.
The thickness ,size , type of the cloth will influence the actual washing capacity.
It is suitable to put inreasonable amount of laundries and the laundries can be turned
round in washing for one time washing.
4. Close the top lid
If you open the top lid,the machine will stop working and alarm in
spinning process.
Do not select more than "4" water level for laundries less than 1.0kg ,so as to avoid
splashing of water.
|