AUTOMATIC DRUM
WASHING MACHINE
XQG60-HA800TX(M)
XQG60-HA1000TX(M)
INSTRUCTIONS FOR
INSTALLATION AND
OPERATION
FUNCTION INTRODUCTION
FUNCTION COMPARING TABLE
MODE
XQG60-HA800TX(M)
XQG60-HA1000TX(M)
6kg
FUNCTION
6kg
18
●
Washing capacity
Programmes
18
●
●
●
Cotton
Synthetic
Wool
●
●
●
Adjustable thermostat(0~90 C)
Cold wash button
●
●
●
●
●
Speed button
Economic button
Spin speed
850r/min
1000r/min
Power switch
ON/OFF
●
●
●
●
●
●
Rinse
Stainless steel tub
Door-locking device
●
●
●
●
Power
300W
530W
72Kg
300W
Power(Wash)
Power(Spin)
530W
72Kg
Weight
850X550X595
HX.WX.D
2
Installation
Unpacking
levelling and
positioning
Remove the package and check that the machine is
undamaged.
If you have any doubts, do not use the machine and call on a
qualified technician. Keep all packing parts (plastic bag,
foam rubber, screws etc.) out of the reach of children since
theycouldbedangerous.
Important: The inside of the washing machine which
consists of a floating unit, is fixed with screws at the back of
the cabinet (Fig.1) during transport. Before starting the
machine remember to release the floating unit by removing
the above screws . To prevent water spray from entering the
machine, remember to close the holes left open by the
screws with the plastic caps provided in the packet
containing the owner's manual. And rescrew the holes
where the iron piece is taken down with the former two
screws.Attention:keep the packing screws and plastic caps
in a safe place for later use. It is important for the machine to
be perfectly level (the angle of inclination on the work surface
must not be more than 2 degrees). For this reason the
machine is fitted with adjustable feet used for levelling the
machine before use (Fig.2). In the case of flooring with
carpeting, remember to check that the ventilation in the
support area is not plugged.
Fig.2
Fig.1
3
Installation
Connect the plug to a socket provided with efficient earthing.
Electric
connection
Or use the spare earthing wire supplied together with the
machine and the earthing terminal located on the left-upper
corner of the back of your machine (Warning: this appliance
must be earthed as a safety measure according to the law).
Make sure that the voltage and frequency available
correspond with the values stated on the data plate located at
the back of the machine (power range:187-242V) and that the
electric system is dimensioned to withstand the maximum
current shown on the data plate. If the socket the machine is
connected to does not correspond with the plug, replace the
plug with a suitable one and avoid using adaptors or shunts
since they could cause overheating and burn out.The spare
eathing wire is absolutely not allowed to be connected to
water pipe,heating pipe or other kinds of pipes.
Connection
of tap and
Loading
Hose
Connect the inlet hose to a cold water tap with a 3/4 gas
threaded opening, and fit the filter and the rubber gasket
supplied with the washing machine. Check that it is tightly
screwedtothetap(Fig. 3).
Fig. 3
If the water piping is new or has not been used for a long time,
before making the connection, let the water run until it is clear
andfreefromimpurities.
This step is necessary to ensure that the incoming water
doesnotclogandpossiblydamagethemachine.
4
Installation
Connection of
the Drain Hose
Connect the drain hose to a drain duct (with internal
diameter of at least 4 cm.) or place it for drainage into
a sink or a tub, ensuring that there are no kinks or
bends. The free end must be at a height of between
80 and 100 cm. Should it be necessary to fix the end
of the hose at a height of less than 80 cm from the
floor, the hose must be fixed in the appropriate hook
on the upper part of the back panel (Fig.4) or use the
suppliedsupporttofixthedrainhose.(Fig.5)
Fig.5
Fig.4
Insert stainless steel screen washers into end of each
supply hose and attach that end of supply hose to
your 3/4" water tap spigot.Be sure that you match up
cold water to "C" and hot to "H".Note:Home Centers
also have"Y" connectors and "Couplings" which
enable you to connect the machine to your sinks
faucet.
Connecting
WaterSupply
5
Close up
G
D
F1
C
E
H
A
B
XQG60-HA800TX(M)
V
1
2
IV
III
3
4
II
I
5
30
MAX
80
F
1
2
3
4
5
6
7
prewash
intense
normal
delicate
rinse
A
B
C
D
E
intense
normal
delicate
rinse
I
delicate
rinse
E
II
40
ON
500
850
III softening
Cotton
Synthetic
Wool
70
soak
50
OFF
softening
soak
spin
60
D
6
IV
V
spin
softening
spin
Draining
C
F
7
B
A
G
D
F2
C
E
H
A
B
XQG60-HA1000TX(M)
V
IV
1
2
III
3
4
II
I
5
30
MAX
80
F
1
prewash
intense
normal
delicate
rinse
A
intense
normal
delicate
rinse
I
delicate
rinse
E
2
3
4
5
6
7
B
C
D
E
II
40
ON
600
III softening
Cotton
Synthetic
Wool
70
soak
50
OFF
1000
softening
soak
spin
60
IV
V
spin
D
6
softening
spin
Draining
C
F
7
B
A
6
Close up
A Programme selector lcwob.
By turning this dial (clockwise only) you can
select from eighteen wash programmes the one
mostsuitedforyourwashing.
1~7cottoncycle
V
1
2
IV
III
3
4
II
I
5
F
E
D
6
C
7
B
A
A~Fsyntheticcycle
I~V woolcycle
B Programme selector Knob.
With this dial you can set the wash temperature
that you desire.For synthetic and wool, the
thermostat works below 60C and 40C
respectively.
30
MAX
80
40
70
50
60
When the dial is located at " ", a cold wash is
available
C PowerLight
This light indicates whether the electricity is on or
off. The light comes on when button D is pressed
and goes off when button D is not pressed.
D ON/OFFButton
ON/OFF button. Supplies electrical power to the
machine.
7
Close up
E EconomicWashButton.
It reduces water and power consumption when rinsing
ifthemachinedoesnothaveafullload.
(Lessthan3kg)
F1 Speed Button.
500
850
Push the button down, to reduce spin speed
from850r/min to 500r/min during strong washing
modeandmediumwashingmode
F2 Speed Button.
600
Push the button down, to reduce spin speed
from1000r/min to 600r/min during strong washing
modeandmediumwashingmode
1000
G Detergent Dispenser.
The detergent dispenser is divided into 3 compart-
mentsmarked1,2,3:(SeeFig.8)
1Pre-washdetergent
2Washdetergent
3Softeners, conditioners, perfumes
3
2
1
Fig.8
H DoorLockButton
The button is used to open the door, but we must
remember that only when the washer doesn't work,we
can open the door. After the washing program
finish,after 3 minutes, when the self-lock meter turn off,
we can open the door.
8
Using instructions:Your machine
offers the best results when...
In order to get the excellent results that you would expect
from your washing machine, it is important to load the washer
correctly. You should therefore choose the quantity of each
typeoffabricthatyouwanttowash.Thistablewillhelp:
The weight
is right
Colour fastfabrics
Delicate fabrics
Woollens
maximum load 5 kgs/11 lbs
maximum load 2 kgs/2.5 lbs
maximum load 1 kg/2.2 lbs
maximum load 2.5 kgs/5.5 lbs
Mixed fabrics
Divide the laundry by fabric and degree of soiling loaded
making the loads as uniform as possible.
Pull the handle out to open the door.
Laundry has
been loaded
correctly
Place the laundry in the machine remembering to arrange
uniformly.
9
Using instructions:Your machine
offers the best results when...
The correct
A perfect wash depends above all on choosing the most
programme has suitable programme. We would therefore advise you to
been chosen
divide up your washing into separate loads of more or
less the same types of fabric. This will make it easier to
selectthebestprogramme.
Hints on choosing the programme are shown in the table
onpagesofthismanual.
Onceyouhaveselectedaprogramme, justturndial
A clockwise until the chosen programme lines up with
theindicatorlineonthefaciapanel.
Anti-crease
When your machine is washing synthetic fabrics or
woollens, the wash cycle stops before the last spin cycle,
with the laundry soaked in water in order to prevent the
formation of creases due to spinning. Complete the
wash cycle with a spin cycle or simply drain the water
fromthewashingmachinewithoutspinning.
For the spin cycle, turn the selector knob A clockwise by
onestep.
To drain, set the selector knob A on drain programme in
both cases, before turning the knob A remember to
switchOFFtheON/OFFbuttonD.
10
Using instructions:Your machine
offers the best results when...
The detergent
has been put
in properly
The 3 compartments marked 1, 2, 3 (Fig.9) should be
usedasfollows:
1Pre-washdetergent
2Washdetergent
3 Conditioner, starch, scents
3
2
1
Fig.9
Remember that it is important to use the right amount of
soap powder or liquid for the type of laundry you are washing;
the amount of detergent you use depends on a number of
factors:
●Water hardness; if the water in your area has a
high calcium content, we recommend using a
anti-limestone additive.
●degree of dirtiness; increase the amount of
soap powder used in the case of heavily soiled
laundry.
●laundry load; the smaller the load the less soap
powder you will need to use.
11
Using instructions:Your machine
offers the best results when...
Thefollowingtablewillguideyou:
Compart.1 Compart.2
Laundry
Compart.3
prewash
wash
Normally 1/2 measuring 1 and 1/2
Softeners
soiled
cup
measuring (see note 3)
cups
When using concentrated detergents, remember to keep to the
manufacturer's instructions using only the measuring cups
supplied with the packet.
Use more detergent in the case of very hard water ( more than
21.F), but remember to maintain the proportion between the
prewashandwashcycles.
Liquiddetergent
The liquid detergents currently available on the market may be
used with the washing machine. Use compartment 2 for very
dense liquid detergents. Follow the manufacturer's
instructions when using liquid detergents sold with the ball
detergent dispenser. Place the ball dispenser in the tub of
washing machine together with the laundry.
The prewash cycle may not be used with liquid detergents.
Note "3"
For soft and fluffy laundry always a softener in the final rinsing
cycle.
Never place bleach in the other compartments.
12
Using instructions:Your machine
offers the best results when...
You can now start washing. We would advise you, especially
the first few times, to check that the programme that you
have set is really the one you want and that the fabric
selection is correct.
The cycle is
started
If you want to start the cycle immediately, press the ON/OFF
buttonD.
At the end of the chosen cycie, the machine will stop
automatically.
The wash is
finished
Press the ON/OFF button D to switch off the power (light C
willturnoff).
13
Maintenance: five simple
precautions for this machine
Your machine is designed to last without complicated
maintenance.
All the same, we would ask you to take care of a few small
matters. If you follow these four simple rules, we are sure that
the washing machine will stay as your faithful friend and
helperforalong, longtime.
1. Ensure that your machine was installed according to the
installation manual that comes with this booklet.
2. Avoid at all costs using solvents either to clean the
machine, or to do the wash. when clean the machine, cut
offthepower.
3. Clean the detergent dispenser every so often. This is very
simple and should be done with water. Your machine has
an extractable dispenser to make it even easier. Just pull it
upwards and out.
4. If it is long time no use, you'd better cut off the power,
switch off the tap, and open the door to avoid unpleasant
smell.
5. Your washer is equipped with a self-cleaning pump. It is
therefore not necessary to carry out cleaning and
maintenanceoperations.
Open the cover of the filter, loosen the knob in counter-
clockwise rotation, then take out the filter and clean it with
water, everymonth.(seeFig.8)
Note: Reassembly the filter carefully after cleaning,
Fig.8
ensuring it is fit perfectly and no water can come out.
14
Solution to Problems
Even though your washing machine has been carefully
designed and constructed, something could still go a miss
with your machine. Before rushing to phone one of our
service centres, however, please check that the operations
listed below have been carried out. In many cases you will
save time, money and bother. Our statistics show that many
of the calls received by our service centres could have been
avoidedwithjustalittlemoreattention.
Checkthat:
· theplugispushedrightintothemainssocket;
thedoorisclosedtightly:
·
· the "ON/OFF"buttonhasbeenpressed.
The washing
machine
won't start
Checkthat:
· thetapisopenandproperlyconnectedtotheinlet
pipe;
· theinletpipeisnotbent.
The washing
machine won't
fill with water
The machine
fills and drains
continuously
Checkthat:
· thedrainpipeisplacedatleast80cm/32inches
above ground level.
The machine
will not drain
drain the water
Check that:
· thedrainpipeisnotblocked;
· thedrainpipeisnotconnectedataheightmorethan
1 metre/40inchesabovegroundlevel.
There is too
much foam in
the tub
Checkthat:
· thedetergentbeingusedismeantforautomatic
machinesandnotforwashingbyhand;
· thattheamountusedisthatshowninthismanual
and not more.
15
Solution to Problems
Check that:
The machine
vibrates too
much when
spinning
· thetransitboltshavebeenremoved(see
installation manual);
· themachineislevel;
· thewashingloadisaccordingtotheinstructions
given in this booklet.
Check that:
· thereisasuddenpowerfailureorwaterstop.
The machine
stops operating
before finishing · themachineisinthenormalstateofrinse.
16
Guide for selecting programme
Wool cycle
Synthetic cycle
Cotton cycle
17
Warning:
1. If the supply cord is damaged, it must be replaced, these are
available from an authorised service agent.
2. The appliance must be placed so that the plug is accessible.
3. The appliance is to be connected to the water mains using new
hose-sets, old hose-sets should not be reused.
4. The appliance is not intended for use by yong children or infirm
persons without supervision. Yong children should be supervised
to ensure that they do not play with the appliance
5. if the appliance is supplied from a cord extension set or electrical
portable outlet device the cord extension set or electrical portable
outlet device should be positioned so it is not subject to splashing
Or ingress of moisture.
6. Use the new hose and the old hose should not be reused
7. Ensure carpet does not obstruct the opening in the bases.
18
WIRING CIRCIUT (XQG60-HA1000TX(M))
I6=1000/600
I4=ON/OFF
L Line
I5=ECONOMIC WASH
MT Timer motor
N Neutral
RR Heating element
SL Line LED
SO Door LED
THR Adjustable heating thermostat
EVP/EVF Water electrovalve
MR Thermal lock
PS Drain pump
M motor
P1 1-level pressure switch
P2 2-level pressure switch
WIRING CIRCIUT(XQG60-HA800TX(M))
I6=850/500
I4=ON/OFF
L Line
I5=ECONOMIC WASH
P1 1- level pressure switch
P2 2- level pressure switch
TM Timer motor
N Neutral
SL Line LED
SO Door LED
H Heating element
MR Thermal lock
D Drain pump
EVF/EVP Water electrovalve
|