Haier Washer HKS1000TXVE HKS1000TXME User Manual

Automatic Drum Washing Machine  
HKS1200TXVE/ME  
HKS1000TXVE/ME  
HKS800TXVE/ME  
Table of Contents  
Before using the appliance  
Name of parts...inside front cover  
Matters needing attention......1-3  
Installation.............................4-5  
Function ...............................6-7  
How to operate the wasing machine  
Program description table........8  
Preparation .............................9  
Washing Procedure ..........10-11  
Maintenance  
Maintenance ..........................12  
Troubleshooting Guide ..........13  
Technical Specifications ........14  
Wiring Circuit .........................15  
 
Matters Needing Attention  
ƽ Safety  
2. Hold the plug and not the electric cable when  
ꢀꢁ  
.A separate earthed socket is required for the  
power supply. The washing machine must be  
positioned so that the plug is accessible.  
unplugging the washing machine.  
4. Do not touch or use the washing machine bare-  
footed or when the hands or feet are wet.  
3.Fuses in the power circuit should be rated for 15A.  
If the supply cord is damaged, it must be replaced  
by the manufacturer, its service agent or similarly  
qualified persons in order to avoid a hazard.  
5.Do not use flammable detergent or dry clean 6. The door of the washing machine will become hot  
ing agent; do not use flammable spray in close  
vicinity to the washing machine; do not remove  
or insert the plug in the presence of flammable  
gas.  
during the heating process. Avoid contact with the  
door during the heating process. For safety, keep  
children away from the washing machine.  
Keep children away from the packing materials after unpacked.  
 
Matters Needing Attention  
Wiring Circuit  
8.The washing machine should not be installed 9. The carpet must not obstruct the ventilation  
HKS1200TXVE/ME HKS1000TXVE/ME HKS800TXVE/ME  
outdoors or in a damp place. In the event of water  
leakage or splashes allow the machine to dry  
naturally.  
openings in the base of the washing machine.  
L
N
Power Switch  
Door Lock  
ST-1  
ST-2  
ST-3  
ST-4  
ST-5  
ST-6  
ST-7  
ST-8  
ST-9  
Display PCB  
O1  
J12-3  
O2  
D1  
J12-4  
J12-11  
D2  
D3  
J12-12  
J12-4  
N1  
N2  
J12-1  
J12-2  
Adjustable Thermostat  
Drain Pump  
M1B1  
Power Drive PCB  
P1  
P2  
J12-11  
J12-5  
M
11.During installation, ensure that the electric  
cable is not trapped by the washing machine  
10.Keep away from heat sources and direct sunlight  
to prevent plastic and rubber components from  
aging.  
M2B2  
B3  
B4  
M3  
M4  
VH2  
Motor  
VH1  
J12-7  
J12-8  
J12-9  
and avoid damage to the electric cable.  
Dear customer,For the machine and your own  
security,DO NOT REPAIR IT BY YOURSELF!  
DO NOT USE THE WASHING MACHINE WHICH  
SOME PARTS ARE LOST!  
V1  
Economic Wash Switch  
V2  
M5B5  
G
B6  
M6  
L2  
L1  
L3  
H1  
H2  
Pressure Switch Heating Element  
During Use  
1. Before use, check the joints of the filling hose,  
the tap and the drainage hose for possible  
problems from water pressure fluctuations.  
If joints are loose or there is leakage, turn  
off the tap and repair. Do not use the washing  
machine until the hoses are properly fixed.  
Keep the door slightly open when the washing  
machine is not in use to prevent formation of  
odors; do not cover the washing machine with  
plastic cover so that inside dampness cannot  
be kept in.  
2.  
2
15  
 
Matters Needing Attention  
Technical Specifications  
Model  
HKS1200TXVE/ME  
220V~(50Hz)  
2100  
HKS1000TXVE/ME  
3. Do not place heavy, heating source or wet articles  
on the top of the washing machine.  
4. Do not hot wash foam rubber or sponge-like  
materials.  
HKS800TXVE/ME  
220V~(50Hz)  
2100  
Power supply  
Power(Max)  
220V~(50Hz)  
2100  
Water pressure (MPa)  
<
1
<
0.05  
P
<
1
<
0.05  
P
<
1
<
0.05  
P
Washing power(W)  
Spinning power(W)  
160  
450  
5
160  
450  
160  
450  
5
5
800  
9
Max. wash load (kg)  
Spinning speed (MAX) (r/min)  
Wash program  
5. Before washing, do up zippers, buttons and clothes  
straps and put small articles, such as socks, laces  
or bras, into a washing bag or a pillow.  
6. Do not open the detergent distribution drawer  
during the wash cycle..  
1200  
9
1000  
9
Heating power (W)  
Weight (kg)  
1900  
1900  
1900  
Steel wires in bras will pop  
out during washing; never  
wash bras containing steel  
wires.  
74  
74  
74  
I
Anti-Electric Shock  
Anti-Water Class  
I
I
IPX4  
IPX4  
IPX4  
8. After each wash program, turn off the tap to prevent  
leakage; and unplug the washing machine and  
wipe clean the lower part of the porthole.  
7. The door is fitted with a self-lock device and will not  
open until 2~3 minutes after the washing machine  
stops. Do not force the door open. Do not open the  
door if water level can reach the porthole.  
ꢀꢃ  
 
Installation  
Troubleshooting  
ƽ
Remove all the packing materials (including the  
The following circumstances do not constitute problems. Do not contact the maintenance service  
until the problem has been confirmed.  
foam base)to prevent vibration during use, as  
shown in Fig.1.Upon opening of the package,  
water drops may be seen on the plastic bag and  
the porthole. This is normal phenomenon resulting  
from water test in the factory.  
Problem  
Possible cause  
Fig. 1  
Poor connection to power supply  
Power failure  
The washing machine fails to operate  
ƽ
Door is not properly closed (It will show E1)  
Machine has not been switched on  
Check attachments and materials with reference to the following  
Name  
Operation  
manual  
Water  
hose  
Drainage  
holder  
Plastic  
plugs  
Quality  
Qty  
certificate  
Water tap is not turned on(It will show E5)  
Water pressure is less than 0.05Mpa  
The inlet hose is kinked  
Model  
Washing machine cannot be filled  
with water  
HKS1200TXVE/ME  
HKS1000TXVE/ME  
HKS800TXVE/ME  
1
1
1
3
Water supply failure  
1
The program dial is not properly set  
The door is not properly closed  
The inlet hose filter is blocked  
The height of the drainage hose is below 80cm (it  
should be within 80-100cm)  
The drainage hose end is in water  
The machine is draining while is  
being filled  
ƽ
Dismantle the packing bolts as shown in Fig. 2.  
The packing bolts are designed for clamping anti-vibration components  
inside of the washing machine during the transportation process.  
Before use:  
1. Remove the back plate;  
2. Remove the three packing bolts on the back plate and take out the  
rubber hose;  
Drainage hose is blocked (It will show E2)  
Drainage hose end is exceed 100cm above the floor  
Drainage failure  
level  
The filter is blocked  
Not all packing bolts have been removed  
3. Replace the back plate;  
Washing machine is located on an uneven surface  
Machine load is over 5kg.  
Not all foam packing has been removed from the motor  
Strong vibration during spin drying  
4. Fill the holes left by the packing bolts with plastic plugs.  
(Attention: The packing bolts and rubber hose should be kept in a safe  
place for later use)  
Operation stops before completion  
of a wash cycle  
Water or electricity failure  
Washing machine is in soak cycle  
Fig.2  
Fig.3  
ƽ
Adjusting the washing machine  
Washing machine is in soak cycle  
Operation stops for a period of time  
Washing machine gives an error message.  
There are adjustable feet under the bottom of the washing machine. Before  
use, the washing machine should be adjusted, as shown in Fig. 3, so that it  
is level.  
Excessive foam in the drum, which  
is spilled to the distribution drawer  
The detergent is not a low-foaming type or for manual  
wash  
Excessive use of detergent  
13  
4
 
4. Clean the filter Cleaning methods (once a month)  
1) Push out the outer cover (Fig. 1);  
2) Screw out filter by turning counterclockwise (Fig. 2);  
3) Flash clean with running water;  
4) Replace the filter by turning clockwise and remount the  
cover.  
Caution: The filter must be in place, or it may lead to  
leakage.  
F
Fig1  
Fig2  
Fig3  
The appliance is to be connected to the water mains using new hose-sets  
and that old hose-sets should not be reused.  
12  
5
 
Hints for Saving Energy  
Operational Functions  
.
4. Setting washing temperature  
Press the temperature button until "_ _ oC" is displayed if heating is not needed; otherwise, select  
an appropriate temperature as required (refer to the "Guide to Operational Program Selection").  
Speed  
Load  
Tamp  
HKS1200TXVEME  
Easy lroning Delay Timer Prewash Extra Rinse Super Wash  
ON/OFF  
5. Function selecting button  
/
Select functions as required (refer to the "Operational Functions" section).  
$ꢇIroning-free b  
utton  
Press this button, the  
reduce wrinkles.  
laundry will be fluffed  
6. Washing  
up at the end of the  
spinning cycle to  
Press the Start / Pause button, the indicator at the upper left corner of the button will blink  
and the washing machine starts operation.  
B:Delay button  
Press the Delay button before the program is started if necessary. Press of the Delay button  
one time, the delay time will increase one hour (the regulating range is from the current setting  
to 24 hours). After the delay time is changed, press the Start button to activate the delay  
function.  
7. Finish  
Note: The delay time must be longer than the program time; otherwise, the washing machine  
will start the wash program directly.  
The washing machine will stop operation automatically when a wash cycle ends. The "End" sign will  
appear. Open the door and take out the laundry. Then turn off the tap and unplug the power cable.  
C:Pre-wash button  
Press this button, the washing machine will automatically start a prewash cycle during  
execution of a washing program.  
D: Extra rinsing button  
Press this button, the washing machine will run an additional rinsing cycle to further clean your  
clothes.  
ƽ
Hints for saving energy  
During operation  
E: Super wash button  
1. Collect clothes for one full wash load.  
2. Do not overload the washing machine.  
3. Pre-wash heavily soiled clothes.  
4. Reduce the amount of detergent or choose standard or delicate wash  
programs for slightly soiled clothes.  
5. Choose a proper washing temperature. Only exceed 60  
soiled clothes.  
6. Do not use more detergent than required.  
Press this button,the display will be on when choosing super wash button. The "  
"
and "  
system finished.  
" will display circularly. The sign of super wash will be off when the super wash  
F: Washing load button  
ć
for heavily  
Press this button, 3 load levels of "ϔϔϔϔ" (0-1.5kg), "ѠѠѠѠ" (1.5-3kg) and "ϝϝϝϝ"  
(3-5kg) will appear on the screen for manual selection before water is filled. After the load is  
set, the water content will be automatically adjusted.  
7. Softening agent makes clothes feel softer and easier to iron.  
G: Power button  
Press this button to switch on the washing machine; press it again to switch the machine off.  
To cancle a wash program during a wash cycle,please switch the machine off.  
ꢀꢀ  
 
Functions  
Washing Procedure  
H: Wash programming knob and start button  
By turning the knob clockwise or counterclockwise, the required program can be selected;  
press the start button to start a program; press it again to pause  
1. Loading  
Open the door, put in the laundry piece by piece.  
Close the door tightly.  
Load Reference  
ƽꢅ-HDQVꢅ  
ꢈꢉꢊꢊJꢋ  
Notes: 1) When first using the washing  
machine,let it run unloaded for one program  
to prevent the laundry from being tainted by  
oil or dirty water from the washing machine.  
2) Do not overload the washing  
machine.  
I: Speed button  
ƽ
(cotton appr 950g)  
Overalls  
ƽ Pajamas  
Press this button to set a required spinning speed, which covers 0 rpm to 1200 rpm.  
(0-1200rpm for HKS1200TXVE/ME 0-1000rpm for HKS1000TXVE/ME  
0-800rpm for HKS800TXVE/ME )  
(appr 200g)  
ƽBlended fabric  
clothes  
(appr 800g)  
ƽ Shirts  
(appr 300g)  
ƽ
T-shirt  
ƽ
Underwear  
(cotton  
J : Temperature button  
Press this button to set a required temperature. The selectable temperature range is  
0-90Ɔ. (Some programs have temperature limits. Refer to the programming guide)  
appr 300g)  
(blended fabrics appr 70g)  
ƽ Socks (blended  
fabrics appr 50g)  
ƽ Jackets (cotton  
appr 800g)  
ƽ Single bed sheets  
(cotton appr 800g)  
ƽ Woolen  
blankets  
(appr 3000)  
K: Display  
Remaining time, set temperature, spinning speed, other function information, and error messages  
are displayed. Refer to the Display Description  
2. Adding detergent  
Slide out the detergent drawer and put the required detergent and  
softening agent into the corresponding boxes. Push back the drawer gently.  
Caution:  
/ꢇDetergent distribution drawer  
There are instructions on the handle of the distribution drawer. Swing  
out the drawer, three compartments can be seen.  
Compartment 1: Pre-washing detergent. If pre-wash is not selected, do  
not add detergent.  
Compartment 2: Detergent for all washing programs. Detergent must be  
added whetherpre-wash is selected or not.  
1) For pre-washing program, detergent should be added to both  
compartments 1 and 2. Compartment 2 allows only solid detergents.  
For other programs, do not add detergent to compartment 1.  
2) Do not overuse softener; otherwise, it will damage the artificial  
fibers. Refer to the instructions during use.  
Compartment 3: Softening agent, conditioning agent, perfume, etc  
B+C: combination for keyboard lock  
After a program is started, press the delay button and the Pre-wash button at the same  
time for 3 seconds, the keyboard will be locked and "SAFE ON" will appear on the screen.  
Press the two buttons again for 3 seconds, the keyboard will be unlocked and "SAFE OFF"  
will be displayed. This function is used to protect the washing machine from being disturbed  
during operation, such as accidental press of buttons or turning of knobs by children, as this  
may affect or suspend the operation of a program. Note: If this function is activated during  
a washing cycle, be sure to inactivate it at the end of the cycle when the "End" sign is  
displayed.  
3. Selecting washing program  
To get the best washing effect, an appropriate washing program should be selected  
according to the laundry type.  
Note: The above operations refer to conditions without power-off memory. Or the washing  
machine will continue operation from where the program was broken. To clear memory,  
press the Start/Pause button. Turn off the power for a few seconds and turn on again, all  
the settings will be renewed.  
Caution: If the keyboard lock is not activated, press the Start/Pause button and then cut off  
the power, the suspended program will be canceled after power is resumed. Now turn the  
program knob to reselect.  
ꢀꢊ  
 
Program Description Table  
Preparation  
Detergent  
1.Power supply  
2.Water supply  
Program Time  
(At Max  
Mode Selection  
Recommended  
Laundry  
Selectable  
Plug in the power supply 220V~50HZ  
Turn on the tap ensure that the water in clear.  
Caution:Before staring the washing machine turn on the water  
faucet to ensure the water faucet and the water inlet hose are  
connected correctly and do not leak  
Temperature  
Temperature)  
3
2
1
Button Position Program  
Intense  
Heavy and  
thick fabrics  
2:26  
ć
0-90  
ƾ
ƾ
Cotton  
White fabrics  
1:41  
ć
0-90  
Normal  
4.Detergent selection  
3.Laundry treatment  
Fast-color and  
medium soil  
fabrics  
Delicate  
ƾ
1:25  
Sort out clothes according to type and extent of dirt.There are  
Only special low foam detergent should  
be used in automatic drum washing  
mashine,form blended or wool fabrics  
special deter-gent should ne used.dry  
clearning solvent should not be used  
such as trichhloroethy-lene or alike  
(caution :load the required amount of  
detergent only).  
0-60  
0-60  
three types of clothes:cotton,synthetical and woolen (silk) fabrics.  
Separate white clothes from colored.If whites and coloreds  
are combimed for one load,make sure the coloreds are colorfast  
Fast-color  
and heavy-  
soil fabrics  
Synthetic  
Normal  
wash  
ƾ
ƾ
0:58  
ć
0-40  
Cashmere Wool and silk  
0:49  
0:46  
-Clothing with frayed edges or yams should be put in a wash  
bag or special bag before washing  
-repair damged clothing,lose buttons or damaged zips  
and hooks before washing.  
-Bed sheets and table ware should be loosely loaded and not  
folded.  
Delicate  
/Super  
Quick  
ć
0-40  
ƾ
ƾ
Wool  
Wool  
Wash  
Medium-soil  
cotton &  
synthetics  
Super  
quick wash  
0:29  
ć
0-40  
This washing mashine is for househould use and designed  
for mechanically washable clothes.When washing,separate  
unwashable clothes with reference to clothes labels.  
Rinse  
0:32  
0:11  
Single  
Wash  
Program  
Spin dry  
5.Wash Load  
Woolen fabrics  
2kg  
non-fade cottens  
Type  
Delicate fabrics  
3kg  
Note :" " indicates that softener or bleacher can be added if needed;  
" ƾ " indicates that detergent must be added;  
Max Load  
5kg  
" X " indicates that detergent must not be added.  
"
"
indicates that if pre-wash is selected,detergent must be added.  
 

Haier Automobile Accessories JF U40B User Manual
Harbor Freight Tools Impact Driver 37730 User Manual
Harbor Freight Tools Impact Driver 92921 User Manual
Harbor Freight Tools Work Light 66308 User Manual
Harman Kardon Stereo Receiver AVR 225 User Manual
Havis Shields Automobile Accessories C VS 2400 CHGR 1 User Manual
Hearth and Home Technologies Indoor Fireplace SL 550TRS E User Manual
Honeywell Clock TE103NL User Manual
Honeywell Home Security System 5894PI User Manual
HP Hewlett Packard Personal Computer vl410 User Manual