Twin-tub Washing Machine
User's manual
This manual is for
HWM80-0626S
HWM80-0626SH
Please read this manual
carefully before using.
Retain it for future reference.
0030807884
Names of the parts
Wash tub cover
Drain selector
Program selector
Wash timer
Outer cover of the spin tub
Inner cover of the spin tub
Spin timer
Control panel seat
Water-filling entrance
Control panel
Plate support(right)
Spin tub frame
Spin tub
Plate support (left)
Water filling control handle
Bypass channel
Front door
Power cord
Water level adjust lever
Overflow filter
Lint filter
Pulsator
Drain hose
Cabinet handle
Wash tub
Cabinet
Base frame
Notes: All illustrations in this Manual are given for reference only. Your products and
accessories may show differences from these illustrations due to our
continuous improvement.
Meaning and description of the symbols
Contents marked with that symbol are related
Warning sign
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.
Contents marked with that symbol are actions
Forbidding sign
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of he user.
Please check if the power receptacle has good earthing condition
before using to guarantee your safety.
1
Safety precautions
When the machine is normally using,
Please insert the power cord into special
receptacle with rated voltage. Be sure to
use single-phase three pins receptacle.
The earthing terminal of the receptacle
must be earthed reliably. If possible,
please adopt electric leakage protector.
please put the power plug at the
location easily to be inserted and
extracted by hand. Be sure to pull the
plug off when there's power failure, or
the machine is being moved, cleaned
or when it is idle.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have
it replaced by the technicians of our special shop or the after-sale service
department.
Do not put the machine at damp
Do not use water hotter than 50 C .
place like the bathroom . Never wash
it with water. Do not place wet laundries
on the control panel.
In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.
Do not wash water-proof laundries like
the raincoat, bike covers etc, to avoid
abnormal vibrations in spinning.
Ventilation hole at
the bottom of the
washing machine
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
2
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not decompose, repair or alter the
machine by yourself.
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.).
ol
tr
Pe
ner
in
h
T
Handicapped or children without care
shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the
heater.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged, please contact the local
after-sale service department of our company.
Install
Dismantle
3
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
Usage of the drain hose
The drain hose shall drain smoothly
1.The height of the drain hose shall be
less than 10cm, or the drainage will not
be smooth, and cost such long time that
<10cm
the machine may stop at mid way.
2.Do not ramp or press the drain hose.
3.If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
>
30mm
4.If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not
less than 40mm, and the length shall
not exceed 1.5m.
<1.5m
If the extra hose is too long, cut it
either at A or at B point.
A
B
4
How to change the direction of the drain hoses
Figure 1 indicates the ex factory installation
position of the drain hose.
Back
Extend the drain hose from the side of spin tub
Front
Figure 1
Put soft items on the ground. Lean the machine
down gently with the front surface facing the
ground. Take off the drain hose from the cabinet.
Dismantle the drain hose fixing clamp and take
the hose out of the fixing groove.
(See to Figure 2).
Soft item
Figure 2
Embed the drain hose into the groove along the side
of the spin tub in the order of 1 ~ 3 , heading for the
side of the spin tub. (See to Figure 3).
Embed the drain hose into the groove with
hands. Take care not to damage the drain
hose in fastening the fixing clamp.
Extend to the
spin tub side
Fig ure 3
Install the water inlet hose; Select the water level
Insert the water inlet hose into the water-filling
entrance on the control panel
To
dismantle the water inlet pipe, just push the
control handle as indicated in the figure and
pull it out
Water inlet
hose
Water-filling
entrance
Select water level according to the
quantity of the laundries.
Set the water level adjusting lever
to needed line.
Water level
indicator
Max
Maximum
Medium
Med
Min
Minimum
5
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose .
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to followings before washing the laundries
Check if
The quantity of When the pulsator
the laundries
shall not be too buttons of the
large. Stretch laundries may
and loosen the cause noise. For
laundries before the sake of
Clear the
Tie the long
strips; fasten
the buttons;
close zippers.
the laundries
has special
requirement
on washing
is running , the
pocket. Take
out the coins,
sand, hairpins
etc.
putting them in discretion, please
the tub.
put the laundries
with buttons into
other laundries.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soi.l
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
6
The musts in washing
The capacity of washing and spinning of the
machine refer to the largest weight of the
standard laundries under dry condition that can
be washed or spinned in one time.
The thickness ,size , type of the cloth will influ-
ence the actual washing capacity. It is suit-
able to put in reasonable amount of laundries
and the laundries can be turned round in wash-
ing for one time washing.
It is suggested to use foamless washing
powder.
Do not select " Max " water level for
laundries less 1.5kg , so as to avoid splashing
of water.
Usage of the detergent
How to use the washing powder
How to use the whitener
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Runfor 30
seconds to dissolve it completely.
3.Put it in the laundries. Select suitable
water level.
Fill water to decided level. Dilute
the whitener with container. Pour
it slowly into the washing tub.
Avoid using whitener on laun-
dries with color or pattern as they
are prone to lose color.
The instant dissolving of thewashing
powder:
1.Prepare warm water of 30C and a
container.
2.Add the powder while stirringto fully
dissolve it.
The whitener shall not touch
the laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
The powder is more proneto pollute the
laundries than the detergent. Therefore
please use it with properquantity.
For powder whitener, please
dissolve it before using.
Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.
7
Washing sequence
Drain switch
Not set the switch to
DRAIN during washing
Spin timer
Function selector
Wash timer
(To set to below 1 minute,
first set to
(Soft current,
Standard current)
2
minutes then
(To set to below 2 minutes,
first set to 6 minutes then
turn it back.).
turn it back. it can increase
the service life of the timer).
OFF
OFF
STANDARD
STANDARD
5
4
1
SOFT
SOFT
DRAIN
CALEFACTION
2
3
(HWM80-0626SH)
(HWM80-0626S)
DRAIN SWITCH
SPIN TIMER
WASH TIMER
FUNCTION SELECTOR
Wash
1.Water-filling selector
1 Set the water inlet selector at the "WASH" side.
(Figure 1)
2 Set the water level adjusting lever to needed line.
2. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
WASH
SPIN
WATER LET LECTOR
Figure 1
Figure 2
Run washing program for some time to stir and
dissolve the powder completely.
STANDARD
STANDARD
SOFT
SOFT
Page7
CALEFACTION
3.Put in the laundries. If the water quantity is
insufficient, please add water.
Figure 3
4.Select the current.
Select the strength of the current according to
the laundries. (Figure 3)
(HWM80-0626S)
(HWM80-0626SH)
FUNCTION SELECTOR
Figure 4
5.Select the washing time
Select the washing time according to the laundries.
(Figure 4)
WASH TIMER
OFF
6.After washing, set the "WASH SELECTOR"
at "DRAIN". (Figure 5).
DRAIN
Figure 5
DRAIN SWITCH
8
Calefaction
Function selector
(Soft current,
Standard current)
STANDARD
SOFT
CALEFACTION
Figure 6
(HWM80-0626SH)
FUNCTION SELECTOR
When filling water to MAX or MED and MIN water levels,
turn the SELECTOR to the CALEFACTION after put in the
laundries. It begins to heat after close the wash tub, when
the temperature reaches 45
5 , the Buzzer will give an
musical alarm. Then turn the selector to "STANDARD"
or "SOFT" , the heater will stop heating and the Buzzer
will stop alarming. It begins to wash after turning the WASH
TIMER.
Remarks Don not open the wash tub when heating
otherwise it will stop heating and influence the heating
time.
9
Midway spinning
1.Put the laundries into the spin tub evenly and smoothly.
2.Spin
(1) Put the gland in properly.
Please put in the gland properly even if the
laundries quantity is small.
Push
Gland
Push
The laundries
are slanting
No gland
Proper
Proper
(2) Close the inner and outer cover of the spin tub.
Outer cover of
The spin tub
Inner cover of
The spin tub
(3) Spin for 1-2 minutes.
3.Run the foam-removing spinning.
Set the inlet selector handle on spin side and
1
fill water for about 1 min.
In case water flows out from wash tub side
due to too much inflow, please turn down
the water tap a bit.
WASH
SPIN
WATER NLET LECTOR
2
Close the spin tub outer cover and spin
for about 1 - 2 min.
10
Rinsing
Rinse with water-filling
1.Put the laundries into the wash tub. Select
suitable current according to the laundries.
2.Adjust the water level
Set the water level with water level adjusting
lever according to the laundries quantity.
Then fill suitable water continuously.
3.Rinse
Adjust the wash timer to 5-7 minutes to do
rinsing.
(Repeat the midway spinning and rinsing with stored
water for 2-3 times.)
Rinse with stored water
1. Put the laundries into the wash tub. Select suitable current
according to the laundries.
2. Fill water to preset water level.
3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.
When the laundries quantity is below 4.0 kg, please use
SOFT current.If you use STANDARD current,
it may splash.
11
Spinning
1.Put the laundries into the spin tub evenly and smoothly.
2.Press the gland in the tub properly. Close the inner and
outer cover of the spin tub.
3.Spin
Select suitable spin time according to the laundries, and do spinning.
During spinning, if there is abnormal sound, it is generally owing to
slanting placement of the laundries. Please stop the machine and
reorder the laundries.
In spinning, it will pause the work if you open the outer cover of the
spin tub. Close it to resume the spinning.
To do spinning and draining and rinse
with water-filling together, please first
do spinning for around 1 minute, then
do draining or rinse with water-filling .
Otherwise the spinning will stop owing
to too much water stored in the spin tub.
12
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter and
overflow filter in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using.
1. Press the elastic piece at upper end of lint filter to
release the tab from the filter cover, and pull the lint
filter outward to remove it. (See Figure 7).
Figure 7
2. Remove lint
Pull the lower end of lint filter rear cover outward
Lint filter rear cover
to disassemble it from the lint filter front cover.
Remove lint completely with clear water. (See
Disassemble
Figure 8).
Install
3. Install lint filter
Lint filter frontcover
Page 8
Figure 8
Cleaning the overflow filter
Too much lint on the overflow filter will influence
the normal usage of the machine. Please
clean it every two months.
1
Take off the overflow filter.
Elastic fixing
claw
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.
13
Cleaning the overflow filter
2. Take off the corrugation pipe.
Dismantle the upper part of the
corrugation pipe inside the
overflow filter ( as indicated in
Figure 9).
Water level
adjusting lever
Corrugation
Pipe
3. Cleaning the overflow filter
Clean the lint around the filter
and flush with tap water.
Figure 9
4. Install the overflow filter.
(1).Install the corrugation pipe.
(2).Insert the mounting plate at
the bottom of the filter into
the valve cover.
Hook
(3).Hang up the hook at the left
upper side.
(4).Push the upper part in (as
indicated in Figure 10).
Figure 10
Disposal of the complete unit
After washing, dismount the water inlet
hose.
Do not store water in the tub for long
period. Discharge the water immediately
after each using.
Pull off the power plug and hang up the
power cord.
Hang up the drain hose.
Wipe the complete unit with soft
cloth twisted dry.
Wipe with neutral detergent if too
dirty.
Do not wash it directly by water.
Wipe off the water drops on the surface
and inside the tub with clean soft cloth.
Open the cover of the wash tub and the
inner/outer cover of the spin tub for
some time (about one hour), then close
them.
Petrol
Thinner
Alcohol
14
Trouble-shooting Answers to question
If the laundries fall to the outer side of the spin tub
If the laundries fall to the outer side of the spin tub, Please
take it out quickly.
1.Dismantle
First take two plugs out, then dismantle the two
screws which fixed the Spin tub frame. As
indicated in the figure, push the point marked
with " " to pull the spin tub frame to oblique
upwards to dismantle it.
Spin tub frame
Figure 1
Spin tub
Please check carefully. The laundries may fall to the
lower part of the outer side of the spin tub ( Figure 2).
If the laundries fall to the outer side of the spin tub,
during spinning the draining will get blocked and the
rotation speed of the spin tub is reduced.
Laundries
Figure 2
2.Install
After install the back edge of the spin tub frame to
proper position, push the four points marked with
"
" by force to reset it, fix it with screws, then
fixed the two plugs at the position.
Figure 3
When the remained water is frozen
Prevent the freezing
Drain completely after using.
When the water is frozen
Below 50
Pour hot water below 50
into the wash tub
to soak it completely. Then turn the pulsator
with hands gently. Please confirm the drainage
can work normally before next using.
15
Trouble-shooting Answers to question
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending
it to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do not repair it by yourself.
Phenomena
The reason
Is there power failure?
The machine does
not act.
Is the power plug loose?
Is the pulsator twisted by foreign materials?
Does the drain hose put down?
Is the drain hose frozen?
The draining does
not work.
Is the drain hose blocked by foreign material?
Are there laundries falling to the outer side of
the spin tub?
There's abnormal
sound during
washing
Are there hair pin, coins or metal items brought
inside the tub?
Is the machine slanting?
There's abnormal
sound and violent
vibration during
spinning
Is the gland pressed evenly?
Are there laundries falling to the outer side of
the spin tub?
Are the laundries in spin tub too much?
There may be some
waterflowing out of
the drain hose in the
first use of the
It is the water remained in the factory inspection
of performance.
machine.
16
Packing list
Name
Quantity
User's manual
One piece
Warranty card
Water inlet hose
One piece
One piece
One piece
One set
Gland
Twin-tub washing machine
Specification
Water level / Water
quantity (about)(L)
Maximum/71 Medium/60 Minimum/49
Injection pressure(MPa)
0.02 0.2
8.0/6.0
Rated washing / spinning
capacity kg
17
|