Haier Washer HWM85 728 User Manual

Fully Automatic Washing Machine  
User's manual  
This manual is for  
HWM85-728  
Please read this manual carefully  
before using.  
Retain it for future reference.  
0030508582  
 
Packing list  
Names of the parts  
Names of the parts  
Name  
Quantity  
One piece  
User's manual  
Warranty card  
Top lid component  
Water inlet valve  
Water absorption  
cushion  
One piece  
Detergent box  
Control panel seat  
Outer tub cover  
Lint filter  
Water inlet hose  
Back control  
board  
The end connecting to  
the washing machine  
One piece  
Jointer connecting  
the water inlet hose  
to the water faucet  
Balance ring  
Inner tub  
Power cord  
Filter cover  
Pulsator  
Control panel film  
The end connecting to  
the water inlet hose jointer  
Handle  
Drain hose  
Hook  
Blenching filler  
Cabinet  
Base  
One piece  
Put into the innner tub  
Bottom plate  
Screw cover  
Adjustable foot  
seam  
Adjustable leg  
Back cover  
Meaning and description of the symbols  
Tapping screw  
One piece  
Warning sign  
Contents marked with that symbol are related to the  
safety of the product and the personal safety of the users.  
Please operate in strict conformity to the contents.  
One set  
Fully automatic washing machine  
Contents marked with that symbol are actions forbidden  
to perform. Performing of those action may result in  
damage of the machine or influence the personal safety of  
the users.  
Forbidden sign  
1
 
Trouble-shooting Answer to question  
Safety precautions  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.  
Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department  
or after-sale service department of our company. Do not repair it by yourself.  
The washing machine must be positioned  
Please plug the power plug on special  
receptacle. Be sure to use three-pins  
power receptacle. Ensure that the earthing  
prong of the power receptacle is earthed  
reliably. Use leakage protector if possible.  
so that the plug is accessible. Be sure to pull the  
plug off and close the water faucet in  
following cases: power failure, delivering  
the machine, setting the machine idle or  
cleaning the machine. Do not plug  
Phenomena  
The reason  
How to settle  
The digitron displays E0.  
The top lid is opened during reserve procedure.  
Close the top lid.  
or pull the power plug with wet hand.  
Put down the drain hose. Open and close the  
top lid once.  
Clean the foreign material. Open and close the  
top lid once.  
The drainage cannot work, or is too slow.  
The digitron displays E1.  
Is the drain hose put down?  
Is the drain hose blocked?  
It stops running in midway. The digitron  
displays E2.  
The top lid is not closed.  
Close the top lid.  
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.  
Keep the pin of the power plug clean, if the power plug is polluted with dust,  
please wipe with dry cloth carefully.  
If the power cord or the power plug is bad, to avoid risk it is  
required to have it replaced by the technicians of our  
special shop or the after-sale service department.  
The safety switch acts, and the  
spinning cannot work. The  
digitron displays E3.  
Reorder the laundries. Close the top lid.  
Th machine will start running after 10  
seconds of being placed horizontally.  
Are the laundries put slantingly?  
Is the machine slanting?  
Is the water tap opened, or is there water  
supply failure?  
Is the water inlet valve blocked?  
Is the water pressure too low?  
Open the water tap. Push the start/Pause  
button once.  
Clean the water inlet valve then push  
the start/Pause button once.  
Push the Start/Pause button once.  
The water filling does not work, or is  
slow. After about 30 minutes later,  
the digital displays E4.  
Do not use water hotter than 50  
.
In case the washing machine is installed on ground  
with carpet, do not block the ventilation hole with  
carpet.  
Please contact the after-sales  
service department.  
The digitron displays E6.  
The water level sensor is bad.  
Is there power failure?  
Is the power plug inserted tightly?  
Is the water level reached preset position?  
Please use it when there's power supply.  
Insert the power plug tightly.  
Fill water to the preset position.  
Not wash  
The ventilation holes  
at the bottom  
The machine does  
not act  
Carpet  
Is the power plug inserted tightly?  
Is the top lid closed reliably?  
Are the laundries set flat?  
Insert the power plug tightly.  
Close the top lid.  
Set the laundries flat.  
Not spin  
Adjust the machine to be even  
Reorder the laundries and close the top lid.  
Remove the foreign materials.  
Is the machine slanting?  
Are the laundries put slantingly in spinning?  
Are there any foreign materials?  
There's abnormal sound  
inside the machine  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
Do not put the machine at damp place like  
the bathroom. Never wash it with water. Do  
not put wet laundries on the control panel.  
Is the screw of the jointer of water  
inlet hose loose or awry?  
Fasten the screw of the jointer properly.  
The water tap leaks  
Common phenomena  
Phenomena  
Explanation  
Balance the laundries to avoid slanting.  
The spinning is intermittent when it starts.  
The wash procedure is paused.  
The cloth sensor is checking the cloth, it will add water after 48 seconds.  
The program is setting the drain time. Some time is needed  
before it starts spinning.  
Push the PROGRAM button to select SPIN,  
but it doesn't work.  
Do not let the machine share one receptacle with other  
electric appliances. If the plugging into the receptacle  
is loose, do not use the plug any more.  
The pulsator pauses during water inlet  
in wash and rinse.  
It is to avoid splashing during water inlet.  
There may be some water flowing out of the  
drain hose in the first use of the machine.  
It is the water remained in the factory inspection of performance.  
2
 
Disposal after washing  
Safety precautions  
After using, please clean the lint and foreign materials of the lint filter etc. in time.  
Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Do not put hand into the rotating tub. It is dangerous  
Do not decompose, repair or alter the machine by  
yourself.  
even if the rotation speed is slow. Take special care of  
the children. Keep children away from the washing  
machine to avoid them climbing on.  
The lint filter must be used during washing.  
Clean the detergent box and set it on  
It must be cleaned in time after each using.  
the control panel seat.  
Lint filter:  
1.The method of dismantle: Push it up aslant and gently.  
1.Push down the spring piece of the top lint filter  
to make the claws out of the filter cover, and then  
pull out the lint filter to get it down. figure1  
2.Pull the back of the lint filter, and then you can  
get down it off the front cover of the lint filter. figure2  
3.Sweep the rubbish in the lint filter.  
2.The method of install : install it upwards and aslant  
and push it in .  
Do not wash laundries with volatile materials  
(such as thinner, petrol etc.).  
Do not put any hot or heavy items (such as the  
kettle with hot water) on the washing machine.  
4.Put the back of the lint filter into the front cover .  
5.Put the lint filter into filter cover, and make it  
tight .  
trol  
Pe  
Benzene  
6.Make sure the lint filter well installed, or it can  
influence your use.  
Up  
The back cover of lint filter  
Up  
Install  
Dismantle  
Dismantle  
Install  
Dismantle  
Install  
Down  
The front cover of lint filter  
Figure 2  
The handicapped or children without care shall not use  
the machine.  
Down  
Keep the machine away from direct sunlight and  
heat source like the heater.  
Figure 1  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
The filter screen of the water inlet valve is likely to be  
blocked by foreign materials and influence the water  
inlet.  
Wipe it with neutral detergent.  
Please clean it with brush every two months.  
Do not wipe it with thinner, petrol, alcohol etc.  
Benzene  
Please keep the lint filter in good condition,  
and install it to proper position during  
washing. If the lint filter is lost or  
To protect your laundries and washing machine,  
please take out all of the coins, buttons, sand, hairpin  
and other foreign materials before washing.  
Install  
Dismantle  
damaged, please contact the customer  
care agent of our company.  
.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.  
It is suggested to use foamless washing powder.  
To change the direction of drain pipe, please contact the customer care agent of our company.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time  
(about 1 hour), then close the top lid.  
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,  
please be sure to ensure the washer is placed under the room temperature for 24 hours and then use  
otherwise the washing effects may be lowered or the washer may be damaged.  
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual.  
It is very important to your security and correct operating the machine.  
Attention  
.
Even there's no water in the tub, a certain period is  
required before spin starting.  
Do not use the soak program for the woolen textiles.  
Separate the laundries that are not colorfast from  
other laundries in washing.  
Install the bottom plate  
After opening the package, please lean the  
washing machine gently down on soft items  
(like towel cloth,blanket, etc.). Install the bottom  
plate to the bottom of the machine with one  
screw by a cross screwdriver, then lift the machine  
up gently. See to the figure:  
I
Front  
I enlarge  
The pulsator will not rotate unless the water is  
filled to"18L"water level.  
Carpet  
The soak procedure can work in cooperation with automatic programs like standard,normal, jeans, and fiber .  
There is intermittent pulsator stirring during soak.  
After the machine starts operation, you can only set the program and procedure during washing,soak and can not  
make setting in other cases.  
Back  
The two claws of bottom plate should  
insert the two strip holes ,and insure  
3 Push the "PROCESS" button  
You can choose one or more process among soak, wash, rinse, spin.  
The button is invaid if you choose QUICK or TUB DRY program.  
Adjust the Installation position  
You can not choose soak process if you choose WOOL  
program.  
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground  
will result in unstable running or stoppage of the machine. Please adjust it with following methods:  
WATER  
LEVEL  
4 Push the " WATER LEVEL"button, select suitable water level  
Confirm it's horizontal:  
Hang the lead line to check if it is  
horizontal.  
After switching on the power and the "standard"or" normal"programs set,washing machine will execute fuzzy  
program automatically to detect the cloth.After defection, it can set the water level automatically. To select other  
water level, first push the "start/pause" button, then push the "water level" button to  
set the water level.  
Adjust the adjustable leg:  
1 .To twist the adjustable leg, please first lift up the  
side of the leg slightly, loosen the adjustable nut,  
and twist the leg.  
the adjustable nut  
Fasten  
Loosen  
2 . After adjustment, fasten the nut.  
the adjustable feet  
5 Push the "SELF-PROGRAM"button and "+ " " -"button  
High  
Low  
to select suitable program  
Set up timeOf soaking, washing, dehydration and times of rinse you can also set up an  
appointment; set that means chosen the appointment booking functions, after start,  
the light of process you choose will be off,a digital displays the remaining appointment  
time (hours). Appointment process, holding down the "self-programming"button to display  
the status of an appointment thatshows the procedureof your choice, water, process and  
the remaining time (minutes). Run theprogram to changeor cancel an appointment,  
need to cutoff the powersupply, re-select.In the light of article 11 can be"self-programming"  
button and select button "+""-".  
6 Push the "START/PAUSE" button  
As the top lid opened, the washer will automatically given alarm and stop running,  
exclusively during draining  
7 Finish washing  
After the laundry process, washing machines beep alarm, and then automatically power off  
 
How to change the direction of the drain hose  
6 "START/PAUSE" button  
WATER  
LEVEL  
After the power is switched on, press it to start the machine  
During working, push it to pause.  
During pause, push this button to restart and go on working.  
1.Loosen the screws of back cover, dismantle the back cover, then take off the drain hose  
(As indicated figure 1)  
Figure 1  
REMAIN(MINUTES) indicator digitron  
During sensing, it displays --  
Drain hose  
frame  
RESERVE(HOURS)  
2.Take off the drain hose from base, nip flat the drain hose mouth, dismantle the hang hook, take the  
drain hose into cabinet from the left of base As indicated figure 2)  
During delay procedure, it displays the remained delay time (in hours).  
During operation of programs, it displays the remaining time (in minutes).  
In case of abnormal phenomenon, it displays the abnormal symbols  
Figure 2  
nip flat the drain hose  
mouth, dismantle the  
hang hook  
Steps of using the operation buttons and description of each step.  
3.Extend the drain hose from the right side of base, fix the drain hose onto the base with the drain  
hose frame, and screw down the screws, put the hang hole onto the drain hose ,then hang up the  
drain hose.(As indicated in Figure 3)  
POWER  
ON/OFF  
1.Push the "POWER ON/OFF " button to switch on the power  
Figure 3  
It has the special power resume function. In the case of power failure or the power plug is loose  
during running , the machine can save the running program, and resume the program after the  
power supply is recovered. You do not need to set the program again.  
4.Install the back cover as primary state.  
2.Push the "PROGRAM" button to select the suitable  
automatic program  
Remarks: in order to make sure of the correct of installation, it is suggested to change the  
direction of the drain hose with our company serviceman .  
Usage the drain hose  
After switching on the power, the machine will set STANDARD program automatically. To select other  
automatic program, push the "PROGRAM" button till the relative indicator is light . Refer to the  
"PROGRAM "button on Page 10 for the selection. For instance: select "QUICK" program for laundries  
The drainage shall be smooth with the drain hose.  
1.The height of the drain hose shall be less than 10cm,  
or the drainage will not be smooth, and cost such long  
time that the machine may stop at mid way.  
4.If extra drain hose is needed, please make separate  
purchase. The inner diameter of the extra hose shall  
not less than 30mm, and the length shall not exceed  
1.5m.  
with small quantity and light soil.  
Page 10  
In selecting the standard program, the machine will execute fuzzy program to select water level  
and wash time according to the cloth and weight of the laundries. The full process is controlled  
automatically.  
2.Do not step on or press the drain hose.  
Attention  
Even there's no water in the tub, the spinning will start  
after a certain period.  
Wash and spin after putting the damageable clothes  
into tuck net, to avoid scathe.  
3. If the drain hose is too long, cut it at mid point. To make  
smooth drainage, cut the front end of the hose slantingly.  
5.If the extra hose is too long, cut it either at A or at B.  
Wash the laundries that are prone to lose colors separately  
from other laundries.  
When washing start or opening cover intermitting, the washing machine will begin  
to work after a period time, this is normal phenomenon.  
Only select rinse program,If there's water inside the tub, the machine will spin before  
rinsing ,If there's no water the machine will rinse directly.  
5
12  
 
Install the water inlet hose  
Confirm the water faucet  
3 "PROCESS"button  
You can choose one or more process among soak, wash, rinse, spin.  
The button is invaid if you choose QUICK or TUB DRY program.  
PROCESS  
Water faucet,suitable  
Water faucet,not suitable  
You can not choose soak process if you choose WOOL  
program.  
Outlet end surface  
4 "SELF-PROGRAM"button and "+ " " -"button  
>10mm  
Press the "Self-Program" button, the machine goes into the  
self-program state when the associated indicated light  
flickers. About 3 seconds later, you can change the program  
by pressing "+" or " " button, to adjust reserved time (hour),  
soak time (minute), washing time (minute), spinning time  
(minute) or rinsing times (number of times) . When the time or  
number of times is 0, it means you cancel all the functions the  
flicker lights associated with.  
When choosing the "quick" program, you can add or reduce  
the reserved time. Choosing the "wool" program, you can add  
or reduce the reserved time but cannot change the washing,  
spinning time and rinsing times, it means the washing time,  
spinning time and rinsing times are defaulted time, times or  
zero. When choosing the "Tub dry" program, the "Self-  
Program" and "+" "-" button are invalid.  
It is required that the front end shall be longer than 10mm.  
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.  
SELF-PROGRAM  
Connection between the water inlet hose jointer and the water faucet  
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the  
water inlet hose component. See to Figure 1.  
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.  
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen  
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,  
otherwise it may leak water. See to Figure 3.)  
water inlet hose jointer  
Screw  
When choosing the "memory" program, after using the self-  
program, the washing machine will remember the programs  
you set this time when you use it next time.  
Slider  
Sign plate  
Screw knife  
Bushing  
Lock level  
water inlet hose  
Figure 1  
Figure 2  
Figure 3  
5 "WATER LEVEL"button  
During standard programs, the washing machine can detect the laundries automatically.After  
detection, it will set the water level to suitable valve automatically among the water level  
"LOW","MEDIUM" ,"HIGH"and "MAXIMUM".  
3.Fasten the four screws evenly. See to Figure 4.  
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure  
to seal up the exit end face of the faucet. See to Figure 5.  
.
You can also set water level by yourself.After the machine is started, it will not set water level  
automatically. You shall push the"START/PAUSE" button to make new setting.  
remark: Before installation, the threading is 4mmabove the upper surface of the nut.  
If there's water inside the tub, the machine can not detect the laundries and will display water  
level "MEDIUM" .If wet aundries are put in, it may display water level "MAXIMUM" .  
WATER  
LEVEL  
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.  
If "QUICK" program is selected, it will display water level "LOW". The water level can not  
be adjusted.  
During operation of wash , rinse and soak program, you can push down the water level  
button to add water. When you release the button, or it reaches the overflow water level, the  
machine will stop adding water.  
About 4mm before twisting  
About less than 2mm after twisting  
Screw nut  
The water level decided may be different from actual value because of the different moisture  
level of the laundries.  
Figure 6  
Figure 4  
Figure 5  
 
4 Use the operation buttons  
Connection between the water inlet hose and the washer  
RESERVE(HOURS)  
1.Do not take off the water absorption cushion. Please check if the  
66L  
70L  
62L  
52L  
40L  
nut of the water  
cushion is dropped or damaged before each usage. If it happens  
inlet hose  
STANDARD  
57L  
46L  
34L  
MEMORY  
SOAK  
WASH  
RINSE  
please contact our after-sale department immediately.  
POWER  
ON/OFF  
COTTON  
WOOL  
HEAVY  
CHILD  
QUICK  
R
E
S
E
R
V
E
R
I
N
S
E
S
O
A
K
W
A
S
S
P
I
2 Put the nut of the water inlet hose on the valve jointer.  
3 Fasten the nut. Swing it gently to confirm if it's suitable.  
26L  
18L  
H
N
START  
PAUSE  
TUB DRY  
SPIN  
(M  
(M)  
(H)  
(T)  
(M)  
jointer of the  
water inlet valve  
water absorption  
cushion.  
WATER  
LEVEL  
SELF-PROGRAM  
PROGRAM  
PROCESS  
Connection between the jointer of the water inlet hose and the water inlet hose  
the jointer of the  
water inlet hose  
1.Push down the slider. Insert the water inlet hose into the jointer.  
Slider  
Locking level  
2 Hang the lock lever to the jointer. Release the slider till a click  
sound is heard.  
Mode and meaning of the indicators  
The light is off  
Flashing: indicate the running program or indicate the water level  
Check the connection between the jointer of the water inlet hose  
and the water faucet  
On: indicate the program about to run, or indicate the selected mode or indicate the water level  
1 "POWER ON/OFF"button  
Push the "POWER ON/OFF"button to switch on the power.  
1.Swing the hose gently to confirm if it is fastened stable.  
POWER  
ON/OFF  
2.After installation, open the faucet to check if it leaks.  
3.Do not bend the hose with overstrain.  
Under power-on mode, push it to switch off the power.  
Push the "POWER ON/OFF" button to switch on the power. If the "START/PAUSE"button is not pushed, the  
machine will switch off the power automatically after 5 minutes.  
4.Before each usage please check if the connection  
between the jointer of the water inlet hose and the  
water faucet, and the installation of the water inlet  
hose are firm, so as to prevent dropping from  
improper installation position.  
2 "PROGRAM"button  
Applicable situation  
Program  
STANDARD  
Washing the normal laundries  
HEAVY Washing the bigger and heavier lanudries  
GENTLE  
Washing the woolen textiles or underwear  
Quick waching of the light dirt laundries  
Dismantle the water inlet hose  
QUICK  
PROGRAM  
BLANKET  
Washing the blanket  
1. Close the water faucet.  
COTTON Washing the cotton textiles  
2. Press the locking lever. Push down the slider. Then pull of the water inlet  
hose.  
Washing the woollen textiles  
WOOL  
Locking level  
Drying the inner tub and the outer tub, which can avoid growing mildew.(after washing  
clothes,there is dampness between the inner tub and the outer tub, the wall of the inner tub  
TUB DRY and out tub can breed mildew, where you can choose thetub dry program, Drying the inner  
tub and the outer tub, keeping the inner tub and outer tub dry, which can avoid growing mildew.  
If the machine is used frequently, the jointer of the water inlet hose can be  
kept on the faucet to prevent damaging the fixing screw.  
Slider  
 
1 Preparation before washing  
2.Put in the laundries  
The capacity of washing and spinning of he  
Preparation before washing  
1.Connect the water inlet hose  
machine refer to the largest weight of the standard  
laundries under dry condition that can be washed or  
spinned in one time.One time washing quantity  
shall be lower than the rated capacity.  
The thickness, size, type of the cloth will influence  
the actual washing capacity. It is suitable for one  
time washing to put in reasonable amount of laundries  
and the laundries can be turned round in washing.  
2.Confirm that the washing machine is earthed  
reliably. Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose  
Do not select high water level for laundries less than  
1.0kg ,so as to avoid splashing of water.  
3. Usage of the detergent  
How to use the softener  
The usage and dose of the softener as per the specifications  
of softener.  
Before washing put the softener into the detergent box directly  
as indicated in the left figure The softener will be put into the  
washer when the last rinsing.  
Control panel seat  
4.slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally  
Liquid whitener inlet  
Access for detergent  
After that,please close the detergent box.Refer to the following  
list for the usage of the detergent:selection of the water level,  
water quantity and dosage of detergent.  
Pay attention to followings before washing the laundries  
After the softener is put in, please don't place for a long time  
otherwise softener may solidify and cause flowing not smooth.  
The quantity of the  
laundries shall not  
exceed the rated  
value. The big  
laundries like the  
jeans shall be put  
in loosely.  
When the pulsator is  
running ,the buttons of  
the laundries may cause  
noise. For the sake of  
discretion ,please put  
the laundries with  
buttons into other  
Confirm if there's  
special requirement  
for the laundries.  
Clear the pocket.  
Take out the coins ,  
sand, hairpins etc.  
Fasten the buttons  
and zippers.  
Detergent box  
How to use the washing powder  
Access for softener  
Directly dissolved in the machine (not applicable for  
fuzzy program )  
1.Fill small quantity of water.  
2.Add the powder. Run for 30 seconds to dissolve it  
completely.  
How to use the whitener  
laundries.  
Fill water to decided level .Dilute  
the whitener with container. Pour it  
slowly into the washing tub.  
Avoid using whitener on laundries  
with colour or pattern as they are  
prone to lose colour.  
3.Put in the laundry. Select suitable water level.  
The instant dissolving of the washing powder:  
1.Prepare warm water of 30 and a container.  
2.Add the powder while stirring to fully dissolve it. In  
selecting the quick program, it is suggested to adopt  
liquid detergent instead of washing powder to  
guarantee the washing effect.  
Put in the proper quantities detergent according to the  
water level and the laundries quantities.  
It is suggested not to use high sudsing detergent.  
Washing powder with poor quality or long time storage  
maybe caked. Please pay attention to cleaning the  
detergent box in time.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,  
please apply detergent in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.  
f. Do not put those laundries polluted by chemicals directly into the washing machine.  
g.For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into  
mesh bag for washing.  
The whitener shall not touch the  
laundries directly.  
Refer to the user's manual for the  
usage and quantity of the whitener.  
For powder whitener, please  
dissolve it before using.  
 
 

Haier Freezer HFH 50 User Manual
HANNspree Flat Panel Television ST06 15U1 User Manual
Harrington Hoists Saw EAC700 User Manual
Hasbro Games 13744 User Manual
Hasbro Games Sonic Hover Jet User Manual
Hayter Mowers Lawn Mower 615E User Manual
Honeywell DVR HD DVR 1004 User Manual
Honeywell Wireless Office Headset 9590 User Manual
Husqvarna Trimmer 235FR User Manual
Hypertec Camera Accessories D7968PHY User Manual